| |
|
 |
MAXIM - Dallas Semiconductor
|
| Part No. |
MAX17116QEVKIT
|
| OCR Text |
...ted. follow the steps below to verify board operation. caution: do not turn on the power supply until all connections are completed. 1) verify that jumper ju1 is in the default position, as shown in table 1. 2) connect the ... |
| Description |
Evaluation Kit for the MAX17116 in a 24-Pin TQFN Package
|
| File Size |
140.04K /
6 Page |
 View
it Online |
Download Datasheet
|
| |
|
|
Maxim
|
| Part No. |
MAX1531EVKIT
|
| OCR Text |
...ettings) MAX1531 PC board
3) verify that a shunt is across pins 1 and 3 of jumpers JU4, JU5, JU6, JU7, and JU8. 4) verify that a shunt is across pins 1 and 5 of jumper JU9. 5) verify that a shunt is across pins 1 and 4 of jumper JU11. 6)... |
| Description |
Evaluation Kit for the MAX1530, MAX1531
|
| File Size |
300.28K /
13 Page |
View
it Online |
Download Datasheet |
| |
|
|
MAXIM - Dallas Semiconductor
|
| Part No. |
MAX1830EVKIT
|
| OCR Text |
...d (if any) from VOUT to GND. 2) verify that there is a shunt on JU1 (shutdown disabled). 3) verify that the JU2 shunt is connected across pins 1 and 4 to set the output to 1.8V. 4) Connect a 3V to 5.5V supply to the pads marked VIN and GND ... |
| Description |
Evaluation Kit for the MAX1830/MAX1831
|
| File Size |
102.66K /
4 Page |
View
it Online |
Download Datasheet |
| |
|
|
Maxim
|
| Part No. |
MAX1906EVKIT
|
| OCR Text |
...oard. Follow the steps below to verify board operation. Do not turn on the battery charger until indicated: 1) verify that shunts are not installed on jumpers JU1, JU2, and JU3 (fuse protection is disabled). 2) verify that shunts are instal... |
| Description |
Evaluation Kit for the MAX1906X/ MAX1906V/MAX1906S
|
| File Size |
108.07K /
5 Page |
View
it Online |
Download Datasheet |
| |
|
|
Maxim
|
| Part No. |
MAX2821EVKIT MAX2820EVKIT
|
| OCR Text |
...e recommended test equipment to verify the operation of the MAX2820/MAX2821. It is intended as a guide only, and substitutions may be possible. * DC supply capable of delivering +5.0V and 200mA of continuous current * * * DC supply capable ... |
| Description |
Evaluation Kits for the MAX2820/MAX2821
|
| File Size |
1,122.76K /
7 Page |
View
it Online |
Download Datasheet |
| |
|
|
Maxim
|
| Part No. |
MAX8620YEVKIT
|
| OCR Text |
...d tested. Follow these steps to verify board operation. Do not turn on the power supply until all connections are completed: 1) verify that a shunt is installed across pins 2 and 3 of jumper JU1. This configures the PWR_ON pin to be pulled ... |
| Description |
Evaluation Kit for the MAX8620Y
|
| File Size |
121.26K /
5 Page |
View
it Online |
Download Datasheet |
| |
|
|
hitachi
|
| Part No. |
HN27C256AP_AFPSERIES C256AP
|
| OCR Text |
...disable Standby Program Program verify Optional verify Program inhibit Identifier CE (20) VIL VIL VIH VIL VIH VIL VIH VIL OE (22) VIL VIH X VIH VIL VIL VIH VIL A9 (24) X X X X X X X VH
*2
VPP (1) VCC VCC VCC VPP VPP VPP VPP VCC
VCC (... |
| Description |
From old datasheet system
|
| File Size |
73.01K /
16 Page |
View
it Online |
Download Datasheet |
| |
|
|
Maxim
|
| Part No. |
MAX9713EVKIT
|
| OCR Text |
...ollow the steps listed below to verify board operation. Do not turn on the power supply until all connections are completed.
Table 1. Recommended Filter Component for Outputs with 8 Load
PART NUMBER L4, L5 C15 C16, C17, C18 C19, C20 R2,... |
| Description |
Evaluation Kit for the MAX9713
|
| File Size |
251.92K /
7 Page |
View
it Online |
Download Datasheet |
| |
|
|
Macronix 旺宏
|
| Part No. |
MX27C4000 27C4000
|
| OCR Text |
... from being programmed. PROGRAM verify MODE Verification should be performed on the programmed bits to determine that they were correctly programmed. The verification should be performed with OE and CEat VIL, and VPP at its programming volt... |
| Description |
4M-BIT [512K x8] CMOS EPROM
From old datasheet system
|
| File Size |
101.01K /
14 Page |
View
it Online |
Download Datasheet |
|
Price and Availability
|
