plx specifications temperature characteristics (max.impedance ratio) category temperature range rated voltage range rated capacitance range capacitance tolerance tangent of loss angle (tan ) esr ( 1) leakage current ( 2) performance characteristics item ? 55 to +125c 16 to 50v 22 to 390f 20% at 120hz, 20c less than or equal to the specified value at 120hz, 20c less than or equal to the specified value at 100khz, 20c less than or equal to the specified value. after 2 minutes' application of rated voltage at 20c z+125c / z+20c 1.25 (100khz) z ? 55c / z+20c 1.25 endurance damp heat (steady state) resistance to soldering heat marking the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 3000 hours at 125c. the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 60c, 90% rh. after soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200c for 60 to 180 seconds and peak temperature at 265c for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. navy blue print on the case top capacitance change tan leakage current ( 2) esr ( 1) within 20% of initial value ( 3 ) 150% or less of the initial specified value 150% or less of the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr ( 1) within 20% of initial value ( 3 ) 150% or less of the initial specified value 150% or less of the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr ( 1) within 10% of the initial capacitance value ( 3 ) 130% or less than the initial specified value 130% or less than the initial specified value less than or equal to the initial specified value high reliability, high voltage (to 50v). low esr, high ripple current. long life of 3000 hours at 125c. radial lead type: lead free flow soldering condition correspondence. adapted to the rohs directive (2011/65/eu). 1 esr should be measured at both of the terminal ends closest to the capacitor body. 2 conditioning : if any doubt arises, measure the leakage current after the voltage treatment of applying dc rated voltage con tinuously to the capacitor for 120 minutes at 105c. 3 initial value : the value before test of examination of resistance to soldering. p 1 l 2 x 3 1 4 v 5 3 6 9 7 0 8 m 91011 capacitance tolerance (20%) rated capacitance (39f) rated voltage (35v) cl 12 1 size code series name type configuration l +0.5max. 15min 4min d0.5 resin coated case d lx 39 v 023 capacitance series lot. no. voltage(v:35v) p 0.5 dimensions type numbering system (example : 35v 39 f) radial lead type, long life assurance dimension table in next page. voltage v 16 20 25 35 50 code c d e v h size d l p d 10 13l 10.0 12.5 5.0 0.6 8 9l 8.0 8.5 3.5 0.6 8 12l 8.0 11.5 3.5 0.6 (mm) conductive polymer aluminum solid electrolytic capacitors please refer to page 20 about the end seal configuration. plx higher temperature plv cat.8100e
61 conductive polymer aluminum solid electrolytic capacitors plx rated ripple current (marms) at 105c 100khz standard ratings rated voltage (v)(code) surge voltage (v) 810 930 1130 800 910 1110 780 890 1080 720 830 1040 700 810 1020 2100 2400 2900 2000 2300 2800 2000 2300 2800 1800 2100 2700 1800 2000 2600 26 25 23 27 26 24 28 27 25 33 31 28 35 33 29 480 704 1248 480 600 1080 410 600 900 273 392 700 220 270 470 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 8 9 812 10 13 8 9 812 10 13 8 9 812 10 13 8 9 812 10 13 8 9 812 10 13 150 220 390 120 150 270 82 120 180 39 56 100 y 22 y 27 y 47 18.4 23.0 28.7 40.2 57.5 16 (1c) 20 (1d) 25 (1e) 35 (1v) 50 (1h) plx1c151mcl1 PLX1C221MDL1 plx1c391mdl1 plx1d121mcl1 plx1d151mdl1 plx1d271mdl1 plx1e820mcl1 plx1e121mdl1 plx1e181mdl1 plx1v390mcl1 plx1v560mdl1 plx1v101mdl1 plx1h220mcl1 plx1h270mdl1 plx1h470mdl1 esr (m ) (at 100khz 20c) rated ripple (marms) rated capacitance (f) case size d l (mm) tan part number leakage current (a) ambient temperature of a capacitor please refer to page 20, 21, 22 about the formed or taped product spec. please refer to page 3 for the minimum order quantity. cat.8100e
|