1 data sheet acquired from harris semiconductor schs198c features maximum frequency, typically 60mhz c l = 15pf, v cc = 5v, t a = 25 o c positive-edge clocking overriding reset buffered inputs and outputs fanout (over temperature range) - standard outputs . . . . . . . . . . . . . . . 10 lsttl loads - bus driver outputs . . . . . . . . . . . . . 15 lsttl loads wide operating temperature range . . . -55 o c to 125 o c balanced propagation delay and transition times signi?ant power reduction compared to lsttl logic ics hc types - 2v to 6v operation - high noise immunity: n il = 30%, n ih = 30% of v cc at v cc = 5v description the ?c4015 consists of two identical, independent, 4-stage serial-input/parallel-output registers. each register has independent clock (cp) and reset (mr) inputs as well as a single serial data input. ? outputs are available from each of the four stages on both registers. all register stages are d- type, master-slave ?p-?ps. the logic level present at the data input is transferred into the ?st register stage and shifted over one stage at each positive- going clock transition. resetting of all stages is accomplished by a high level on the reset line. the device can drive up to 10 low power schottky equivalent loads. the ?c4015 is an enhanced version of equivalent cmos types. pinout cd54hc4015 (cerdip) cd74hc4015 (pdip, soic) top view ordering information part number temp. range ( o c) package cd54hc4015f3a -55 to 125 16 ld cerdip cd74hc4015e -55 to 125 16 ld pdip cd74hc4015m -55 to 125 16 ld soic 14 15 16 9 13 12 11 10 1 2 3 4 5 7 6 8 2cp 2q 3 1q 2 1q 1 1q 0 1mr gnd 1d v cc 2mr 2q 0 2q 1 2q 2 1q 3 1cp 2d november 1997 - revised may 2003 caution: these devices are sensitive to electrostatic discharge. users should follow proper ic handling procedures. copyright 2003, texas instruments incorporated cd54hc4015, cd74hc4015 high speed cmos logic dual 4-stage static shift register [ /title (cd74 hc401 5) / sub- j ect (high speed cmos logic dual 4-
2 functional diagram truth table inputs outputs cp d r q 0 q 1 q 2 q 3 lllq 0 q 1 q 2 hlhq 0 q 1 q 2 xlq 0 q 1 q 2 q 3 xxhllll h = high voltage level h = high voltage level one set-up time prior to the low to high clock transition l = low voltage level l = low voltage level one set-up time prior to the low to high clock transition x = don? care. = low to high clock transition = high to low clock transition q n = lower case letters indicate the state of the referenced output one set-up time prior to the low to high clock transition. 7 6 1mr 1d 1cp gnd = 8 v cc = 16 1q 2 3 10 1q 3 1q 1 4 1q 0 5 9 15 14 2mr 2d 2cp 2q 2 11 2 2q 3 2q 1 12 2q 0 13 1 cd54hc4015, cd74hc4015
3 t6 f absolute maximum ratings thermal information dc supply voltage, v cc . . . . . . . . . . . . . . . . . . . . . . . . -0.5v to 7v dc input diode current, i ik for v i < -0.5v or v i > v cc + 0.5v . . . . . . . . . . . . . . . . . . . . . . 20ma dc output diode current, i ok for v o < -0.5v or v o > v cc + 0.5v . . . . . . . . . . . . . . . . . . . . 20ma dc output source or sink current per output pin, i o for v o > -0.5v or v o < v cc + 0.5v . . . . . . . . . . . . . . . . . . . . 25ma dc v cc or ground current, i cc . . . . . . . . . . . . . . . . . . . . . . . . . 50ma operating conditions temperature range, t a . . . . . . . . . . . . . . . . . . . . . . -55 o c to 125 o c supply voltage range, v cc hc types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2v to 6v dc input or output voltage, v i , v o . . . . . . . . . . . . . . . . . 0v to v cc input rise and fall time 2v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (max) 4.5v. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (max) 6v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (max) thermal resistance (typical, note 1) ja ( o c/w) e (pdip) package . . . . . . . . . . . . . . . . . . . . . . . . . . 67 m (soic) package. . . . . . . . . . . . . . . . . . . . . . . . . . 73 maximum junction temperature . . . . . . . . . . . . . . . . . . . . . . . 150oc maximum storage temperature range . . . . . . . . . .-65 o c to 150 o c maximum lead temperature (soldering 10s) . . . . . . . . . . . . . 300 o c (soic - lead tips only) caution: stresses above those listed in ?bsolute maximum ratings may cause permanent damage to the device. this is a stress only rating and operatio n of the device at these or any other conditions above those indicated in the operational sections of this speci?ation is not im plied. note: 1. the package thermal impedance is calculated in accordance with jesd 51-7. dc electrical speci?ations parameter symbol test conditions v cc (v) 25 o c -40 o c to 85 o c -55 o c to 125 o c units v i (v) i o (ma) min typ max min max min max high level input voltage v ih - - 2 1.5 - - 1.5 - 1.5 - v 4.5 3.15 - - 3.15 - 3.15 - v 6 4.2 - - 4.2 - 4.2 - v low level input voltage v il - - 2 - - 0.5 - 0.5 - 0.5 v 4.5 - - 1.35 - 1.35 - 1.35 v 6 - - 1.8 - 1.8 - 1.8 v high level output voltage cmos loads v oh v ih or v il -0.02 2 1.9 - - 1.9 - 1.9 - v -0.02 4.5 4.4 - - 4.4 - 4.4 - v -0.02 6 5.9 - - 5.9 - 5.9 - v high level output voltage ttl loads - - --- - - - - v -4 4.5 3.98 - - 3.84 - 3.7 - v -5.2 6 5.48 - - 5.34 - 5.2 - v low level output voltage cmos loads v ol v ih or v il 0.02 2 - - 0.1 - 0.1 - 0.1 v 0.02 4.5 - - 0.1 - 0.1 - 0.1 v 0.02 6 - - 0.1 - 0.1 - 0.1 v low level output voltage ttl loads - - --- - - - - v 4 4.5 - - 0.26 - 0.33 - 0.4 v 5.2 6 - - 0.26 - 0.33 - 0.4 v input leakage current i i v cc or gnd -6-- 0.1 - 1- 1 a quiescent device current i cc v cc or gnd 0 6 - - 8 - 80 - 160 a cd54hc4015, cd74hc4015
4 prerequisite for switching speci?ations parameter symbol v cc (v) 25 o c -40 o c to 85 o c -55 o c to 125 o c units min max min max min max maximum clock frequency f max 2 6-5-4-mhz 4.5 30 - 24 - 20 - mhz 6 35 - 28 - 24 - mhz clock pulse width t w 2 80 - 100 - 120 - ns 4.5 16 - 20 - 24 - ns 6 14-17-20-ns mr pulse width t w 2 150 - 190 - 225 - ns 4.5 30 - 38 - 45 - ns 6 26-33-38-ns mr recovery time t rec 2 50-65-75-ns 4.5 10 - 13 - 15 - ns 6 9 - 11 - 13 - ns set-up time, data-in to cp t sul, t suh 2 60-75-90-ns 4.5 12 - 15 - 18 - ns 6 10-13-15-ns hold time, data-in to cp t h 2 0-0-0-ns 4.5 0 - 0 - 0 - ns 6 0-0-0-ns switching speci?ations input t r , t f = 6ns parameter symbol test conditions v cc (v) 25 o c -40 o c to 85 o c -55 o c to 125 o c units min typ max min max min max propagation delay (figure 1) t plh, t phl c l = 50pf 2 - - 175 - 220 - 270 ns clock to q n 4.5 - - 35 - 44 - 54 ns c l =15pf 5 - 14 - - - - - ns c l = 50pf 6 - - 30 - 37 - 46 ns mr to q n , (clock high) t plh, t phl c l = 50pf 2 - - 275 - 345 - 415 ns 4.5 - - 55 - 64 - 83 ns c l =15pf 25 - - - - - ns c l = 50pf 6 - - 47 - 54 - 71 ns mr to q n , (clock low) t plh, t phl c l = 50pf 2 - - 325 - 400 - 490 ns 4.5 - - 65 - 81 - 98 ns c l =15pf 25 - - - - - ns c l = 50pf 6 - - 55 - 69 - 83 ns output transition time (figure 1) t tlh ,t thl c l = 50pf 2 - - 75 - 95 - 110 ns 4.5 - - 15 - 19 - 22 ns 6 - - 13 - 16 - 19 ns input capacitance c in c l = 50pf - - - 10 - 10 - 10 pf maximum clock frequency f max c l =15pf 5 - 60 - - - - - mhz power dissipation capacitance (notes 2, 3) c pd c l =15pf 5 - 43 - - - - - pf notes: 2. c pd is used to determine the dynamic power consumption, per shift register. 3. p d = v cc 2 f i + c l v cc 2 where f i = input frequency, c l = output load capacitance, v cc = supply voltage. cd54hc4015, cd74hc4015
5 test circuit and waveform figure 1. hc setup times, hold times, removal time, and propagation delay times for edge triggered sequential logic circuits t r c l t f c l gnd v cc gnd v cc 50% 90% 10% gnd clock input data input output set, reset or preset v cc 50% 50% 90% 10% 50% 90% t rem t plh t su(h) t tlh t thl t h(l) t phl ic c l 50pf t su(l) t h(h) cd54hc4015, cd74hc4015
packaging information orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) 5962-8995301EA active cdip j 16 1 tbd call ti level-nc-nc-nc cd54hc4015f3a active cdip j 16 1 tbd call ti level-nc-nc-nc cd74hc4015e active pdip n 16 25 pb-free (rohs) cu nipdau level-nc-nc-nc cd74hc4015ee4 active pdip n 16 25 pb-free (rohs) cu nipdau level-nc-nc-nc cd74hc4015m active soic d 16 40 green (rohs & no sb/br) cu nipdau level-1-260c-unlim cd74hc4015me4 active soic d 16 40 green (rohs & no sb/br) cu nipdau level-1-260c-unlim (1) the marketing status values are defined as follows: active: product device recommended for new designs. lifebuy: ti has announced that the device will be discontinued, and a lifetime-buy period is in effect. nrnd: not recommended for new designs. device is in production to support existing customers, but ti does not recommend using this part in a new design. preview: device has been announced but is not in production. samples may or may not be available. obsolete: ti has discontinued the production of the device. (2) eco plan - the planned eco-friendly classification: pb-free (rohs) or green (rohs & no sb/br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. tbd: the pb-free/green conversion plan has not been defined. pb-free (rohs): ti's terms "lead-free" or "pb-free" mean semiconductor products that are compatible with the current rohs requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. where designed to be soldered at high temperatures, ti pb-free products are suitable for use in specified lead-free processes. green (rohs & no sb/br): ti defines "green" to mean pb-free (rohs compatible), and free of bromine (br) and antimony (sb) based flame retardants (br or sb do not exceed 0.1% by weight in homogeneous material) (3) msl, peak temp. -- the moisture sensitivity level rating according to the jedec industry standard classifications, and peak solder temperature. important information and disclaimer: the information provided on this page represents ti's knowledge and belief as of the date that it is provided. ti bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. efforts are underway to better integrate information from third parties. ti has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ti and ti suppliers consider certain information to be proprietary, and thus cas numbers and other limited information may not be available for release. in no event shall ti's liability arising out of such information exceed the total purchase price of the ti part(s) at issue in this document sold by ti to customer on an annual basis. package option addendum www.ti.com 17-oct-2005 addendum-page 1
important notice texas instruments incorporated and its subsidiaries (ti) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. all products are sold subject to ti?s terms and conditions of sale supplied at the time of order acknowledgment. ti warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with ti?s standard warranty. testing and other quality control techniques are used to the extent ti deems necessary to support this warranty. except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. ti assumes no liability for applications assistance or customer product design. customers are responsible for their products and applications using ti components. to minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. ti does not warrant or represent that any license, either express or implied, is granted under any ti patent right, copyright, mask work right, or other ti intellectual property right relating to any combination, machine, or process in which ti products or services are used. information published by ti regarding third-party products or services does not constitute a license from ti to use such products or services or a warranty or endorsement thereof. use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from ti under the patents or other intellectual property of ti. reproduction of information in ti data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. reproduction of this information with alteration is an unfair and deceptive business practice. ti is not responsible or liable for such altered documentation. resale of ti products or services with statements different from or beyond the parameters stated by ti for that product or service voids all express and any implied warranties for the associated ti product or service and is an unfair and deceptive business practice. ti is not responsible or liable for any such statements. following are urls where you can obtain information on other texas instruments products and application solutions: products applications amplifiers amplifier.ti.com audio www.ti.com/audio data converters dataconverter.ti.com automotive www.ti.com/automotive dsp dsp.ti.com broadband www.ti.com/broadband interface interface.ti.com digital control www.ti.com/digitalcontrol logic logic.ti.com military www.ti.com/military power mgmt power.ti.com optical networking www.ti.com/opticalnetwork microcontrollers microcontroller.ti.com security www.ti.com/security telephony www.ti.com/telephony video & imaging www.ti.com/video wireless www.ti.com/wireless mailing address: texas instruments post office box 655303 dallas, texas 75265 copyright ? 2005, texas instruments incorporated
|
