? semiconductor components industries, llc, 2014 june, 2017 ? rev. 5 1 publication order number: ncv2393/d ncv2393, ts393 micropower dual cmos voltage comparator the ncv2393 and ts393 are micropower cmos dual voltage comparators. they feature extremely low consumption of 6 a typical per comparator and operate over a wide temperature range of t a = ? 40 to 125 c. the ncv2393 and ts393 are available in an soic ? 8 package. features ? extremely low supply current: 6 a typical per channel ? wide supply range: 2.7 to 16 v ? extremely low input bias current: 1 pa typical ? extremely low input offset current: 1 pa typical ? input common mode range includes v ss ? high input impedance: 10 12 ? pin ? to ? pin compatibility with dual bipolar lm393 ? ncv prefix for automotive and other applications requiring unique site and control change requirements; aec ? q100 qualified and ppap capable ? these devices are pb ? free, halogen free/bfr free and are rohs compliant soic ? 8 case 751 pin connections device package shipping ? ordering information marking diagram ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our t ape and reel packaging specifications brochure, brd8011/d. www. onsemi.com ncv2393dr2g soic ? 8 (pb ? free) 2500 / tape & reel a = assembly location l = wafer lot y = year w = work week = pb ? free package 1 8 ncv2393 alyw 1 8 1 2 3 45 6 7 8 out 1 in ? 1 in+ 1 vss in+ 2 in ? 2 out 2 vdd ts393dr2g soic ? 8 (pb ? free) 2500 / tape & reel
ncv2393, ts393 www. onsemi.com 2 pin description pin name type description 1 out 1 output output of comparator 1. the open ? drain output requires an external pull ? up resistor. 2 in ? 1 input inverting input of comparator 1 3 in+ 1 input non ? inverting input of comparator 1 4 vss power negative supply 5 in+ 2 input non ? inverting input of comparator 2 6 in ? 2 input inverting input of comparator 2 7 out 2 output output of comparator 2. the open ? drain output requires an external pull ? up resistor. 8 vdd power positive supply absolute maximum ratings (note 1) over operating free ? air temperature, unless otherwise stated parameter limit unit supply voltage, v s (v dd ? v ss ) 18 v input and output pins input voltage (note 2) 18 v input differential voltage, v id (note 3) 18 v input current (through esd protection diodes) 50 ma output voltage 18 v output current 20 ma temperature storage temperature ? 65 to +150 c junction temperature 150 c esd ratings human body model 1500 v machine model 50 v latch ? up ratings latch ? up current 100 ma stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. stresses beyond the absolute maximum ratings can lead to reduced reliability and damage. 2. excursions of input voltages may exceed the power supply level. as long as the common mode voltage [v cm = (v in + + v in ? )/2] remains within the specified range, the comparator will provide a stable output state. however, the maximum current through the esd dio des of the input stage must strictly be observed. 3. input dif ferential voltage is the non ? inverting input terminal with respect to the inverting input terminal. to prevent damage to the gates, each comparator includes back ? to ? back zener didoes between input terminals. when dif ferential voltage exceeds 6.2 v, the diodes turn on. input resistors of 1 k have been integrated to limit the current in this event. 4. this device series incorporates esd protection and is tested by the following methods: esd human body model tested per aec ? q100 ? 002 (jedec standard: jesd22 ? a114) esd machine model tested per aec ? q100 ? 003 (jedec standard: jesd22 ? a115) latch ? up current tested per jedec standard: jesd78. thermal information (note 5) thermal metric symbol value unit junction ? to ? ambient (note 6) ja 190 c/w junction ? to ? case top jt 107 c/w 5. short ? circuits can cause excessive heating and destructive dissipation. values are typical. 6. multilayer board, 1 oz. copper, 400 mm 2 copper area, both junctions heated equally
ncv2393, ts393 www. onsemi.com 3 operating conditions parameter symbol limit unit supply voltage (v dd ? v ss ) v s +2.7 to +16 v operating free air temperature range t a ? 40 to +125 c functional operation above the stresses listed in the recommended operating ranges is not implied. extended exposure to stresse s beyond the recommended operating ranges limits may affect device reliability. electrical characteristics : v s = +3 v ( boldface limits apply over the specified temperature range, t a = ?40 c to +125 c, guaranteed by characterization and/or design.) parameter symbol conditions min typ max unit input characteristics offset voltage v os v cm = mid ? supply 1.4 13 mv 14 mv input bias current (note 7) i ib v cm = mid ? supply 1 pa 600 pa input offset current (note 7) i os v cm = mid ? supply 1 pa 300 pa input common mode range v cm v ss v dd ? 1.5 v v ss v dd ? 2 v common mode rejection ratio cmrr v cm = v ss to v cm = v dd ? 1.5 v 70 db output characteristics output voltage low v ol v id = ? 1 v, i ol = +6 ma v ss + 300 v ss + 450 mv v ss + 700 mv output current high i oh v id = +1 v, v oh = +3 v 2 40 na 1000 na dynamic performance propagation delay low to high t plh v cm = mid ? supply, f = 10 khz, r pu = 5.1 k , c l = 50 pf 5 mv overdrive 2.1 s ttl input 0.6 s propagation delay high to low t phl v cm = mid ? supply, f = 10 khz, r pu = 5.1 k , c l = 50 pf 5 mv overdrive 3.9 s ttl input 0.2 s power supply power supply rejection ratio psrr v s = +3 v to +5 v 70 db quiescent current i dd per channel, no load, output = low 6 15 a 20 a product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. 7. guaranteed by characterization and/or design.
ncv2393, ts393 www. onsemi.com 4 electrical characteristics : v s = +5 v , unless otherwise noted ( boldface limits apply over the specified temperature range, t a = ?40 c to +125 c, guaranteed by characterization and/or design.) parameter symbol conditions min typ max unit input characteristics offset voltage v os v cm = mid ? supply v, v s = 5 v to 10 v 1.4 13 mv 14 mv input bias current (note 8) i ib v cm = mid ? supply 1 pa 600 pa input offset current (note 8) i os v cm = mid ? supply 1 pa 300 pa input common mode range v cm v ss v dd ? 1.5 v v ss v dd ? 2 v common mode rejection ratio cmrr v cm = v ss to v cm = v dd ? 1.5 v 71 db output characteristics output voltage low v ol v id = ? 1 v, i ol = +6 ma v ss + 260 v ss + 350 mv v ss + 550 mv output current high i oh v id = +1 v, v oh = +5 v 2 40 na 1000 na dynamic performance fall time t fall 50 mv overdrive, f = 10 khz, r pu = 5.1 k , c l = 50 pf 25 ns propagation delay low to high t plh v cm = mid ? supply, f = 10 khz, r pu = 5.1 k , c l = 50 pf 5 mv overdrive 2.1 s 10 mv overdrive 1.2 s 20 mv overdrive 0.8 s 40 mv overdrive 0.5 s ttl input 0.6 s propagation delay high to low t phl v cm = mid ? supply, f = 10 khz, r pu = 5.1 k , c l = 50 pf 5 mv overdrive 5.8 s 10 mv overdrive 3.2 s 20 mv overdrive 1.7 s 40 mv overdrive 1.0 s ttl input 0.3 s power supply power supply rejection ratio psrr vs = +5 v to = +10 v 80 db quiescent current i dd per channel, no load, output = low 6 15 a 20 a product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. 8. guaranteed by characterization and/or design
ncv2393, ts393 www. onsemi.com 5 1.25 1 0.75 0.5 0.25 0 figure 1. i ib and i os vs. temperature 048121620 v ol , low level output voltage (v) i ol , low ? level output current (ma) figure 2. v ol vs. i ol v s = 3 v v s = 4 v v s = 5 v v s = 10 v v s = 16 v 450 ? 55 ? 40 25 70 85 125 v ol , low level output voltage (mv) 400 350 300 250 150 100 50 0 t a , free ? air temperature ( c) figure 3. v ol vs. temperature t a = ? 55 c t a = ? 40 c t a = 25 c t a = 70 c t a = 85 c t a = 125 c i dd , supply current ( a) 25 024 101214 v s , supply voltage (v) 68 figure 4. i dd vs. v s 20 15 10 5 0 600 25 45 85 125 current (pa) temperature ( c) 500 400 300 200 100 0 65 105 i ib + i ib ? i os v s = 5 v v cm = mid ? rail v s = 5 v i ol = 6 ma 16 output low no loads total i dd of both channels i dd , supply current ( a) 18 v oh , high level output voltage (v) 16 14 12 10 8 6 4 2 0 figure 5. i dd vs. temperature outputs high outputs low v s = 5 v no loads total i dd of both channels ? 55 ? 40 25 70 85 125 propagation delay (ns) 900 v s , supply voltage (v) 369 303336 800 700 600 500 400 300 27 12 15 18 21 24 t phl t plh figure 6. propagation delay vs. v s overdrive = 50 mv r p = 5.1 k c l = 50 pf t a = 25 c
ncv2393, ts393 www. onsemi.com 6 input amplitude (v) 0.4 propagation delay ( s) ? 11 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 ? 0.05 23 4 5 figure 7. t plh vs. overdrive 40 mv 20 mv 10 mv 5 mv 2 mv v s = 5 v r p = 5.1 k c l = 50 pf t a = 25 c 5 4 3 2 1 0 ? 1 ? 2 ? 3 ? 4 ? 5 ? 6 output amplitude (v) input output 0 input amplitude (v) 0.4 propagation delay ( s) ? 30 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 ? 0.05 36 9 1215 4 3 2 1 0 ? 1 ? 2 ? 3 ? 4 ? 5 ? 6 output amplitude (v) figure 8. t phl vs. overdrive 40 mv 20 mv 10 mv 2 mv v s = 5 v r p = 5.1 k c l = 50 pf t a = 25 c input 5 mv output t fall , fall time (ns) 80 v s , supply voltage (v) 36912 303336 70 60 50 40 30 20 10 0 15 18 21 24 27 figure 9. fall time vs. v s c l = 100 pf c l = 50 pf c l = 15 pf 50 mv overdrive r p = 5.1k to v dd t a = 25 c t a = ? 55 c t a = ? 40 c t a = 25 c t a = 70 c t a = 85 c t a = 125 c offset voltage (mv) input common mode voltage (v) figure 10. v os vs. v cm (v s = 3 v) 1 0.8 0.6 0.4 0.2 0 ? 0.2 ? 0.4 ? 0.6 ? 0.8 ? 1 ? 1.5 0.5 0 ? 1.0 ? 1.0 ? 0.5 v dd = 1.5 v v ss = ? 1.5 v offset voltage (mv) input common mode voltage (v) figure 11. v os vs. v cm (v s = 5 v) 1 0.8 0.6 0.4 0.2 0 ? 0.2 ? 0.4 ? 0.6 ? 0.8 ? 1 ? 1.5 0.5 0 ? 1.0 ? 2.0 ? 0.5 ? 2.5 1.0 1.5 t a = ? 55 c t a = ? 40 c t a = 25 c t a = 70 c t a = 85 c t a = 125 c v dd = 2.5 v v ss = ? 2.5 v
ncv2393, ts393 www. onsemi.com 7 offset voltage (mv) input common mode voltage (v) figure 12. v os vs. v cm (v s = 10 v) 1 0.8 0.6 0.4 0.2 0 ? 0.2 ? 0.4 ? 0.6 ? 0.8 ? 1 ? 1.5 0.5 0 ? 1.0 ? 1.0 ? 0.5 t a = ? 55 c t a = ? 40 c t a = 25 c t a = 70 c t a = 85 c t a = 125 c v dd = 5 v v ss = ? 5 v percentage of units (%) offset voltage (mv) figure 13. offset voltage distribution 20 18 16 14 12 10 8 6 4 2 0 ? 14 10 ? 4 ? 12 ? 6 ? 10 ? 8 ? 28 06 24 14 12 n = 71545 t a = 25 c v s = 3 v v cm = mid ? supply
ncv2393, ts393 www. onsemi.com 8 package dimensions soic ? 8 nb case 751 ? 07 issue ak seating plane 1 4 5 8 n j x 45 k notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 6. 751 ? 01 thru 751 ? 06 are obsolete. new standard is 751 ? 07. a b s d h c 0.10 (0.004) dim a min max min max inches 4.80 5.00 0.189 0.197 millimeters b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.053 0.069 d 0.33 0.51 0.013 0.020 g 1.27 bsc 0.050 bsc h 0.10 0.25 0.004 0.010 j 0.19 0.25 0.007 0.010 k 0.40 1.27 0.016 0.050 m 0 8 0 8 n 0.25 0.50 0.010 0.020 s 5.80 6.20 0.228 0.244 ? x ? ? y ? g m y m 0.25 (0.010) ? z ? y m 0.25 (0.010) z s x s m 1.52 0.060 7.0 0.275 0.6 0.024 1.270 0.050 4.0 0.155 mm inches scale 6:1 *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* ncv2393/d on semiconductor and are trademarks of semiconductor components industries, llc dba on semiconductor or its subsidiaries i n the united states and/or other countries. on semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property . a listing of on semiconductor?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent ? marking.pdf . on semiconductor reserves the right to make changes without further notice to any products herein. on semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does o n semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. buyer is responsible for its products and applications using on semiconductor products, including compliance with all laws, reg ulations and safety requirements or standards, regardless of any support or applications information provided by on semiconductor. ?typical? parameters which may be provided in on semiconductor data sheets and/or specifications can and do vary in dif ferent applications and actual performance may vary over time. all operating parameters, including ?typic als? must be validated for each customer application by customer?s technical experts. on semiconductor does not convey any license under its patent rights nor the right s of others. on semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any fda class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. should buyer purchase or use on semicondu ctor products for any such unintended or unauthorized application, buyer shall indemnify and hold on semiconductor and its officers, employees, subsidiaries, affiliates, and distrib utors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that on semiconductor was negligent regarding the design or manufacture of the part. on semiconductor is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 literature fulfillment : literature distribution center for on semiconductor 19521 e. 32nd pkwy, aurora, colorado 80011 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative ?
|
