View AMT49413GEVATR_9015936.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

amt49413 description the amt49413 is a 3-phase brushless dc (bldc) motor controller for use with n-channel external power mosfets. it incorporates much of the circuitry required to design a cost- effective three-phase motor drive system. the amt49413 provides functionality over a wide input supply range. a unique charge pump regulator provides adequate (>10 v) gate drive for battery voltages down to 7 v , and allows the device to operate with a reduced gate drive at battery voltages down to 5.5 v . power dissipation in the charge pump is minimized by switching from a voltage doubling mode at low supply voltage to a dropout mode at the nominal running voltage of 14 v . a bootstrap capacitor is used to provide the above-battery supply voltage required for n-channel mosfets. an internal charge pump for the high-side drive allows for dc (100% duty cycle) operation. internal fixed-frequency pwm current control circuitry can be used to regulate the maximum load current. the peak load current limit is set by the selection of an input reference voltage and external sensing resistor. the pwm frequency is set by a user-selected external rc timing network. for added flexibility, amt49413-ds features and benefits ? high current 3-phase gate drive for n-channel mosfets ? synchronous rectification ? cross-conduction protection ? charge pump and top-off charge pump for 100% pwm ? integrated commutation decoder logic ? operation over 5.5 to 50 v supply voltage range ? extensive diagnostics output ? provides +5 v hall sensor power ? low-current sleep mode 3-phase bldc controller and mosfet driver typical application continued on the next page package: 48-lead qfn with exposed thermal pad (suffix ev) not to scale amt49413 3-phase bldc motor direction run/stop current limit vbat+ october 26, 2016
2 the pwm input can be used to provide speed and torque control, allowing the internal current control circuit to set the maximum current limit. efficiency is enhanced by using synchronous rectification. the power fets are protected from shoot-through by integrated crossover control with dead time. the dead time can be set by a single external resistor. the amt49413 is supplied in a 48-pin qfn with exposed thermal pad. this is a small footprint (49 mm 2 ) power package, that is lead (pb) free, with 100% matte-tin leadframe plating. selection guide absolute maximum ratings part number packing package AMT49413GEVATR 1000 pieces per 7-inch reel 7 7 mm qfn with exposed pad description (continued) parameter symbol conditions rating units load supply voltage v bb vbb pin C0.3 to 50 v logic input/output voltage v reset reset pin input C0.3 to 6 v remaining logic pins C0.3 to 7 v output voltage range v ghx gha, ghb, and ghc pins v sx to v sx + 15 v v glx gla, glb, and glc pins C5 to 16 v v cx ca, cb, and cc pins v sx + 15 v v sx sa, sb, and sc pins C5 to 55 v csp, csn, and lss pins C4 to 6.5 v cso, vdsth pins C0.3 to 6.5 v vdrain pin C0.3 to 55 v operating temperature range (g) t a C40 to 105 c junction temperature t j 150 c transient junction temperature t tj overtemperature event not exceed- ing 1 s, lifetime duration not exceed- ing 10 hr; guaranteed by design characterization 175 c storage temperature range t stg C55 to 150 c esd rating, human body model aec-q100-002, all pins except cp1 2000 v aec-q100-002, pin cp1 1000 v esd rating, charged device model aec-q100-011, all pins 1050 v thermal characteristics: may require derating at maximum conditions; see applications information section characteristic symbol test conditions* value units package thermal resistance r ja high-k pcb (multilayer with significant copper areas, based on jedec standard jesd51-7) 24 oc/w die-to-exposed pad thermal resistance r jp 2 oc/w *additional thermal information available on allegro website. 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
3 p high-side drive low-side drive blanking charge pump regulator charge pump boostrap monitor +5v ref osc r s q diagnostics and protection ?uvlo ?tsd ?short to supply ?short to ground ?shorted winding ?low load p rsense h1 h2 h3 v5 v5bd ca sa tacho vbb rc ct rt rdead vdrain phase a of three phases vdsth ref csout control logic lss agnd csn pad csp reset test ff1 pwm ff2 gha h1 v5 h2 h3 dir diro gla rgla rgha a b c coast mode brake cp1 cp2 vreg vbat+ creg cboota cp vreg esf cv5 qv5 functional block diagram 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
4 electrical characteristics: valid at t a = 25c, v bb = 7 to 45 v, unless otherwise noted characteristics symbol test conditions min. typ. max. units supply and reference vbb functional operating range 1 v bb function correct, parameters not guaranteed 5.5 C 50 v vbb quiescent current i bbq reset = high, outputs = low C 11 14 ma i bbs reset = low, sleep mode C C 10 a v5 quiescent current i v5q reset = high, outputs = low C C 5 ma vreg output voltage v reg v bb 7.4 v, i reg = 0 to 15 ma 12.10 13 13.75 v 6 v < v bb < 7.4 v i reg = 0 to 15 ma 2 v bb C2.7 C C v 5.5 v < v bb < 6 v, i reg < 10 ma 9 10 C v bootstrap diode forward voltage v fboot i d = 10 ma 0.4 0.7 1.0 v i d = 100 ma 1.5 2.2 2.8 v bootstrap diode resistance r d r d(100 ma) = (v fboot(150 ma) C v fboot(50 ma) ) / 100 ma 6 10 20 bootstrap diode current limit i dboot 250 500 750 ma top-off charge pump current limit i tocpm C 200 C a high-side gate drive static load resistance r gsh 250 C C k v5 output voltage v 5 4.75 5 5.25 v v be of external transistor qv5 v beext C C 1 v v5bd base drive capability for qv5 2 i 5bd C C C2 ma gate output drive turn-on rise time t r c load = 3300 pf, 20% to 80% points C 60 C ns turn-off fall time t f c load = 3300 pf, 80% to 20% points C 40 C ns pull-up on resistance r ds(on)up i ghx = C150 ma 3 4 5 pull-down on resistance r ds(on)dn i glx = 150 ma 1 1.5 2 short-circuit current C source 2 i sc(source) C C500 C ma short-circuit current C sink i sc(sink) C 850 C ma ghx output voltage v ghx t w < 10 s bootstrap capacitor fully charged v cx C 0.2 C C v glx output voltage v glx v reg C0.2 C C v turn-off propagation delay t p(off) from hall input change to unloaded gate output change 300 500 700 ns from other control input change to unloaded gate output change C 150 200 ns dead time (turn-off to turn-on delay) t dead r dead = 5 k C 180 C ns r dead = 50 k 835 960 1090 ns r dead = 400 k C 3.3 C s r dead = tied to v5 C 6 C s continued on the next page... 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
5 continued on the next page characteristics symbol test conditions min. typ. max. units logic inputs and outputs ffx fault output (open drain) v ol i ol = 1 ma, fault asserted C C 0.4 v ffx fault output leakage current 2 i oh v o = 5 v, fault not asserted C1 C 1 a tacho and diro output high voltage v oh i oh = C1 ma v 5 C 1 v C C v tacho and diro output low voltage v ol i ol = 1 ma C C 0.4 v input low voltage v il C C 0.8 v input high voltage (except reset) v ih 2 C C v reset input high voltage v ihr 2.2 C C v input hysteresis v ihys 300 500 C mv input current (except h1, h2, h3, and reset) 2 i in C1 C 1 a reset input pull-down resistor r pd v in = 5 v C 50 C k hx input pull-up resistor r pu v in = 0 v C 100 C k current sense differential amplifier input bias current 2 i ibs csp = csn = 0 v C300 C200 C150 a input offset current 2 i ios csp = csn = 0 v C10 C 10 a csp input resistance r csp measured with respect to agnd C 80 C k csn input resistance r csn measured with respect to agnd C 4 C k differential input voltage v id v id = csp C csn, C1.3 v < csp < 4 v, C1.3 v < csn < 4 v 0 C 200 mv output offset voltage v oos csp = csn = 0 v 100 320 550 mv output offset voltage drift v oos(?t) csp = csn = 0 v C 100 C v/c input common mode range v cm csp = csn C1.5 C 4 v differential input voltage gain a v 40 mv < v id < 175 mv, v cm in range 18.5 19 19.5 v/v low output voltage error v err 0 < v id < 40 mv, v csout = (19 v id ) + v oos + v err C20 C 20 mv dc common mode gain a cmdc csp = csn = 200 mv C C30 C db source resistance r csout v csout = 2 v, C2 ma < i csout < 0.5 ma C 80 C output dynamic range v csout C100 a < i csout < 100 a 0.1 C v 5 C 0.2 v output current C sink i csout(sink) v csout = 2 v 5% C 1 C ma output current C source 2 i csout(source) v csout = 2 v 5% C C19 C ma supply rejection psrr csp = csn = agnd, 0 to 300 khz C 45 C db small signal 3 db bandwidth frequency f 3db v id =10 mv pp C 1.6 C mhz settling time t settle to within 10%, v csout = 1 v pp square wave C 400 C ns ac common mode gain a cmac v icr = 250 mv pp , 0 to 1 mhz C C28 C db common mode recovery time t cmrec to within 100 mv, v icr = +4.1 to 0 v step C 1 C s output slew rate sr 10% to 90% points, v id = 0 to 175 mv step C 20 C v/s input overload recovery time t idrec to within 10%, v id =250 mv to 0 v step C 500 C ns electrical characteristics (continued): valid at t a = 25c, v bb = 7 to 45 v, unless otherwise noted 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
6 characteristics symbol test conditions min. typ. max. units current limit reference comparator input offset voltage v ioc C15 0 15 mv reference input clamp voltage v refc external pull-up to 5 v r ref = 200 k 3.75 4 4.2 v comparator blank time t rc r t = 56 k?, c t = 470 pf C 650 C ns ref input bias current i ibref C 0 C a rc charge current 2 i rc C1.15 C1 C0.85 ma rc high voltage threshold v rch 1.7 1.9 2.1 v rc low voltage threshold v rcl 0.6 0.7 0.8 v protection vreg undervoltage lockout v reguv v reg rising 7.5 8 8.5 v v reg falling 6.75 7.25 7.75 v bootstrap capacitor undervoltage lockout v bootuv v boot falling, v cx C v sx 59 C 69 % bootstrap capacitor undervoltage lockout hysteresis v bootuvhys v bootuvhys = %v reg C 13 C % v5 undervoltage lockout v 5uv v 5 falling 3.4 3.65 4.0 v v5 undervoltage lockout hysteresis v 5uvhys 300 400 500 mv vdsth input voltage range v dsth 0.3 C 4 v vdsth input current 2 i dsth C1 C 1 a vdrain input voltage range v drain 7 v bb 45 v short-to-ground threshold offset 3,5 v stgo v dsth > 1 v C 300 C mv v dsth 1 v, 7 v v drain 30 v C150 C 150 mv short-to-battery threshold offset 4,5 v stbo v dsth > 1 v C 300 C mv v dsth 1 v, 7 v v drain 30 v C150 C 150 mv low load current detection voltage v csol C 500 C mv overtemperature flag t jf temperature increasing C 170 C oc overtemperature flag hysteresis t jfhys recovery = t jf C t jfhys C 15 C oc 1 function is correct but parameters not guaranteed above or below general limits (7 to 45 v). 2 for input and output current specifications, negative current is defined as coming out of (sourcing) the specified device pin. 3 high-side on. as v sx decreases, fault occurs if v bat C v sx > v stg . 4 low-side on. as v sx increases, fault occurs if v sx C v lss > v stb . 5 v stg threshold is v dtsth + v stgo . v stb threshold is v dtsth + v stbo . electrical characteristics (continued): valid at t a = 25c, v bb = 7 to 45 v, unless otherwise noted 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
7 basic operation the amt49413 provides commutation and current control for 3-phase brushless dc (bldc) motors with integrated hall- effect sensors. the motor current is provided by an external 3-phase n-channel mosfet bridge which is controlled by the amt49413, using fixed-frequency pulse-width modulation (pwm). the use of pwm with n-channel mosfets provides the most cost-effective solution for a high-efficiency motor drive. the amt49413 provides all the necessary circuits to ensure that the gate-source voltage of both high-side and low-side external mosfets are above 10 v , at supply voltages down to 7 v. for extreme battery voltage drop conditions, functional operation is guaranteed down to 5.5 v but with a reduced gate drive. the amt49413 also decodes the commutation sequence from three hall-effect sensors spaced at 120 in the electrical cycle, and ensures no cross-conduction (shoot-through) in the external bridge. individual pins provide direction, brake, and coast control. motor current can be sensed by a low-value sense resistor, rsense, in the ground connection to the bridge, amplified and compared to a reference value. the amt49413 then limits the bridge current on a cycle-by-cycle basis. bridge current can also be controlled using an external pwm signal with the internal cur- rent control either disabled or used to set the absolute maximum motor current. specific functions are described more fully in the following sections. power supplies only one power connection is required because all internal circuits are powered by integrated regulators. the main power supply should be connected to vbb through a reverse battery protection circuit. v5 and v5bd a 5 v supply for external pull-up and bias cur- rents is provided by an integrated 5 v regulator controller and an external npn transistor, qv5. the amt49413 provides the base drive current on the v5bd pin, and the 5 v reference on the v5 pin. this regulator is also used by the internal logic circuits and must always be decoupled by at least a 200 nf capacitor, cv5, between the v5 pin and agnd. for stability, a 100 nf capacitor, c5bd, also should be connected between v5bd and agnd. if an external 5 v supply is not required, the v5bd pin and the v5 pin should be connected together. cp1, cp2, and vreg the gate drive outputs are powered by an internal charge pump, which requires a pump capacitor, typi- cally 470 nf, cp, connected between the cp1 and cp2 pins. the output from the charge pump, 13 v nominal, is used to power each of the three high- and low-side driver pairs and is also available on the vreg pin. a sufficiently large storage capaci- tor, creg, must be connected to this pin to provide the tran- sient charging current to the low-side drivers. the charge pump also provides the charging current for the bootstrap capacitors, cbootx. an additional top-off charge pump is provided for each high- side drive which allows the high-side drive to maintain the gate voltage on the external fet indefinitely, ensuring so-called 100% pwm if required. this is a low-current trickle charge pump (< 100 a typical), and is only operated after a high-side driver has been signaled to turn on. there is a small amount of bias current (< 20 a) drawn from the c x pin to operate the floating high-side circuit, and the charge pump simply provides enough drive to ensure that the bootstrap voltage, and hence the gate volt- age, will not droop due to this bias current. the charge required for initial turn-on of the high-side gate is always supplied by bootstrap capacitor charge cycles. hall-effect sensor inputs h1, h2, and h3 hall-effect sensor inputs are configured for motors with 120 electrically-spaced hall-effect sensors, but may be used for 60 electrical spacing with an external inverter. hall-effect sen- sors usually require an additional pull-up resistor to be connected between the sensor output and 5 v . this 5 v can be provided by the integrated 5 v regulator. hall-effect inputs have a hysteresis of typically 500 mv to reduce the effects of switching noise on the hall-effect connections to the motor. these inputs are also filtered to further reduce the effects of switching noise. the hall-effect inputs are pulled-up to 5 v inside the amt49413 through a high value (100 k? typical) resistor in series with a diode. this internal pull-up makes the hall-effect input appear high if the hall sen- sor signal is missing, allowing detection of an hall-effect input logic fault.the amt49413 will indicate a logic fault when all hall inputs are driven to the same logic level. the commutation truth table for these inputs is shown in table 2. the inputs can also be driven directly from a microcontroller or similar external circuit. gate drive the amt49413 is designed to drive external n - channel power mosfet s. they supply the large transient currents necessary to quickly charge and discharge the gate capacitance of the external fets in order to reduce dissipation in the external fets during functional description 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
8 switching. the charge and discharge rate can be controlled using external resistors in series with the connections to the gate of the fets. rdead. cross-conduction is prevented by the gate drive circuits which introduce a dead time, t dead , between switching one fet off and the complementary fet on. the dead time is derived from the value of a resistor, rdead, connected between the rdead pin and agnd. if rdead is connected to v5, t dead defaults to 6 s typical. gla, glb, and glc. low-side gate drive outputs for external nmos drivers. external series-gate resistors, rgate, (as close as possible to the nmos gate) can be used to control the slew rate seen at the power-driver gate, thereby controlling the di/dt and dv/dt of the sx outputs. referring to table 2, glx = 1 (high) means that the upper half (pmos) of the driver is turned on, and that its drain will source current to the gate of the low-side fet in the external motor-driving bridge. glx = 0 (low) means that the lower half (nmos) of the driver is turned on, and that its drain will sink current from the corresponding external fet gate circuit to the lss pin. sa, sb, and sc. directly connected to the motor, these termi- nals sense the voltages switched across the load. these terminals are also connected to the negative side of the bootstrap capacitors and are the negative supply connections for the floating high- side drivers. the discharge current from the high-side fet gate capacitance flows through these connections, which should have low-impedance traces to the fet bridge. gha, ghb, and ghc. high-side gate drive outputs for exter - nal nmos drivers. external series-gate resistors, rgate, can be used to control the slew rate seen at the power-driver gate, thereby controlling the di/dt and dv/dt of the sx inputs. referring to table 2, ghx = 1 (high) means that the upper half (pmos) of the driver is turned on, and that its drain will source current to the gate of the high-side fet in the external motor-driving bridge. ghx = 0 (low) means that the lower half (nmos) of the driver is turned on, and that its drain will sink current from the corre- sponding external fet gate circuit to the respective s x pin. ca, cb, and cc. high-side connections for the bootstrap capacitors and positive supply for high-side gate drivers. the bootstrap capacitors, cboot x , are charged to approximately v reg when the corresponding sx terminal is low. when the s x output swings high, the voltage on the c x pin rises with the out- put to provide the boosted gate voltage needed for the high-side n-channel power mosfets. vdrain. high-impedance sense input (kelvin connection) to the top of the external fet bridge. this input allows accurate measurement of the voltage at the drain of the high-side fets and should be connected directly to the bridge, close to the drain con- nections of the high-side fets, with an independent trace. lss. low-side return path for discharge of the gate capacitors. it is connected to the common sources of the low-side external fets through an independent low-impedance trace. logic control inputs additional logic-level inputs are provided to enable specific features described below. these logic inputs all have a nominal hysteresis of 500 mv to improve noise performance. reset. allows minimum current consumption from the vbb supply. when reset is low, all internal circuitry is disabled including the v5 output. when coming out of sleep state, the protection logic ensures that the gate drive outputs are off until the charge pump reaches proper operating conditions. the charge pump stabilizes in approximately 3 ms under nominal conditions. reset has an internal pull-down resistor, 50 k typical. how- ever, to allow the amt49413 to start-up without the need for an external logic input, the reset pin can be pulled to the battery voltage with an external pull-up resistor. because reset also has an internal clamp diode, 6 v typical, to limit the input current, the value of the external pull-up resistor should be greater than 20 k. the upper limit for the resistor must be low enough to ensure that the input voltage reaches the input high threshold, v inr . coast. an active-low input which turns all fets off without disabling the supplies or control logic. this allows the external fets and the motor to be protected in case of a short circuit. mode. sets the current-decay method. referring to table 3, when in slow-decay mode, mode = 1, only the high-side mos- fet is switched off during a pwm-off cycle. in the fast-decay mode, mode = 0, the device switches both the high-side and low-side mosfets. slow decay allows a lower ripple current in the motor at the pwm frequency, but reduces the dynamic response of the cur- rent control. it is suitable for motors which run at a more-or-less constant speed. fast decay provides improved current-control dynamic response, but increases the motor current ripple. it is suitable for motors used in start-stop and positioning applications. dir. determines the direction of motor torque output, as shown in table 2. for an unloaded, low-inertia motor, this will also usu- 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
9 ally be the direction of mechanical rotation. with a motor that has a high inertial load, the dir input can be used to apply a con- trolled breaking torque, when fast decay is used (mode = 0). brake. an active-low input that provides a braking function. when brake = 0 (see t able 3), all the low-side fets are turned on and the high-side fet s are turned off. this effectively short- circuits the back emf in the windings, and brakes the motor. the braking torque applied depends on the speed. reset = 0 or coast = 0 overrides brake and coasts the motor. note that when brake is used to dynamically brake the motor, the wind- ings are shorted with no control over the winding current. esf. the state of the enable stop on fault (esf) pin determines the action taken when a short is detected. see the diagnostics section for details. test. test is for allegro production use and must be connected to agnd. current regulation load current can be regulated by an internal fixed frequency pwm control circuit or by external input on the pwm pin. current sense amplifier: csp, csn, and csout. a dif - ferential current sense amplifier with a gain, a v , of 19 typical, is provided to allow the use of low-value sense resistors or current shunts as the current sensing elements. because the output of this sense amplifier is available at csout, it can be used for either internal or external current sensing. with the sense resistor, rsense, connected between csp and csn, the output of the sense amplifier will be approximately: v csout (i load a v r sense ) + v oos , where v oos is the output offset voltage (the voltage at zero load current), and a v is the differential voltage gain of the sense amplifier, 19 typical. internal current control: ref. a fixed reference voltage can be applied to provide a maximum current limit. a variable reference voltage will provide a variable torque control. the output voltage of the current sense differential amplifier, v csout , is compared to the reference voltage available on the ref pin. when the outputs of the mosfets are turned on, current increases in the motor winding until it reaches a trip point value, i trip , given by: i trip = (v ref C v oos ) / (r sense a v ) . at the trip point, the sense comparator resets the source enable latch, turning off the source driver. at this point, load inductance causes the current to recirculate until the start of the next pwm period. the current path during recirculation is determined by the configuration of the mode pin. torque control can therefore be implemented by varying the voltage on the ref pin, provided that the pwm input remains high. if direct control of the torque or current by pwm input is desired, a voltage can be applied to the ref pin to set an absolute maximum current limit. the ref input is internally limited to 4 v, which allows the use of a simple pull-up resistor to v5, rref, to set the maximum reference voltage, avoiding the need for an externally generated reference voltage. rref should have a value between 20 and 200 k. internal pwm frequency. the internal oscillator frequency, f osc , is determined by an external resistor, rt, and capacitor, ct, connected in parallel from the rc pin to agnd. the frequency is approximately: f osc 1 / ( r t c t + t blank + t dead ) . where f osc in the range 20 to 50 khz. pwm input. can be used to control the motor torque by an external control circuit signal on the pwm pin. referring to t able 3, when pwm = 0, the selected drivers are turned off and the load inductance causes the current to recirculate. the current path during recirculation is determined by the configuration of the mode pin. setting pwm = 1 will turn on selected drivers as determined by the h x input logic. holding pwm=1 allows speed and torque control solely by the internal current-limit circuit, using the voltage on the ref pin. in some circumstances, it may be desirable to completely disable the internal pwm control. this can be done by pulling the rc pin directly to agnd. this will disable the internal pwm oscil- lator and ensure that the output of the pwm latch is always high. blank time. when the source driver is turned on, a current spike occurs due to the reverse-recovery currents of the clamp diodes and switching transients related to distributed capaci- tance in the load. to prevent this current spike from erroneously resetting the source enable latch, the current-control comparator output is blanked for a short period of time, t blank , when the source driver is turned on. the length of t blank is different for internal versus external pwm. it is set by the value of the timing capacitor, ct, according to the following formulas: 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
10 for internal pwm: t blank (s) = 1260 c t (f), and for external pwm: t blank (s) = 2000 c t (f) . a nominal c t value of 680 pf yields a t blank of 1.3 s for exter- nal pwm, and 860 ns for internal pwm. the user must ensure that c t is large enough to cover the current spike duration when using the internal sense amplifier. diagnostics several diagnostic features integrated into the amt49413 provide speed and direction feedback and indications of fault conditions. tacho and diro. these outputs provide speed and direction information based on the he inputs from the motor. as shown in figure 1, at each commutation point, the t acho output changes state independent of motor direction. the diro output is updated at each commutation point to show the motor direction. when the motor is rotating in the forward or positive direction, diro will be high. when rotation is in the reverse or negative direc- tion, diro will be low. the actual direction of rotation is deter- mined from the sequence of the three hall inputs, h x. forward is when the sequence follows table 2 top-to-bottom and reverse when the sequence follows table 2 bottom-to-top. note that there are some circumstances in which the direction reported on the diro output pin and the direction demanded on the dir input pin may not be the same. this may happen if the motor and load have reasonably high inertia. in this case, changing the state of the dir pin will cause the torque to reverse, braking the motor. during this braking, the direction indicated on the diro output will not change. esf. the state of the enable stop on fault (esf) pin will deter- mine the action taken when a short is detected. for other fault conditions, the action is defined by the type of fault. the action taken follows the states shown in table 1. when esf = 1, any short fault condition will disable all the gate drive outputs and coast the motor. this disabled state will be latched until the next phase commutation or until coast or reset go low. when esf = 0, under most conditions, although the fault flags, ff1 and ff2, are still activated, the amt49413 will not disrupt normal operation and will therefore not protect the motor or the drive circuit from damage. it is imperative that the master control circuit or an external circuit take any necessary action when a fault occurs, to prevent damage to components. if desired, the active low coast input can be used as a crude disable circuit by connecting the fault flags ff1 and ff2 to the coast input and a pull-up resistor to v5. ff1, ff2, and vdsth. fault conditions are indicated by the state of two open drain output fault flags, ff1 and ff2, as shown in table 1. in addition to internal temperature, voltage, and logic monitoring, the amt49413 monitors the state of the external mosfets and the motor current to determine if short-circuit faults occur or a low load condition exists. in the event that two or more faults are detected simultaneously, the state of the fault flags will be determined by a logical and of the fault states of each flag. ? undervoltage. vreg supplies the low-side gate driver and the bootstrap charge current. it is critical to ensure that the volt- ages are sufficiently high before enabling any of the outputs. the undervoltage circuit is active during power-up, and will pull both fault flags low and coast the motor (all gate drives low) until v reg is greater than approximately 8 v. note that this is sufficient to turn on the external power fets at a battery voltage as low as 5.5 v , but will not normally provide the rated on-resistance of the fet. this could lead to excessive power dissipation in the external fet. in addition to a monitor on vreg, the amt49413 also moni- tors both the bootstrap charge voltage, to ensure sufficient high- side drive, and the 5 v reference voltage at v5, to ensure correct logical operation. if either of these fall below the lockout volt- age level, the fault flags are set. ? overtemperature. this event pulls both fault flags low but does not disable any circuitry. it is left to the user to turn off the device to prevent overtemperature damage to the chip and unpredictable device operation. ? logic fault: hall invalid. when all h x have the same value, the amt49413 evaluates this as an illegal code, and pulls both commutation points tacho diro "forward" motor rotation "reverse" motor rotation figure 1: direction indication outputs 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
11 fault flags, ffx , low and coasts the motor. this action can be used, if desired, to disable all fet drives under bridge or motor fault conditions. the hall logic fault condition is not latched, so if the fault occurs while the motor is running, the external fet s will be reenabled, according to the commutation truth table (table 2), when the h x inputs become valid. the hx inputs have pull-up resistors to ensure that a fault condi- tion will be indicated in the event of an open connection to a hall sensor. ? short to ground. a short from any of the motor phase con- nections to ground is detected by monitoring the voltage across the top fets in each phase using the appropriate s x pin and the voltage at vdrain. this drain-source voltage is then compared to the voltage on the vdsth pin. if the drain-source voltage exceeds the voltage at the vdsth pin, ff2 will be pulled low. ? short to supply . a short from any of the motor phase connec- tions to the battery or vbb connection is detected by monitor- ing the voltage across the bottom fets in each phase using the appropriate s x pin and the lss pin. this drain-source voltage is then compared to the voltage on the vdsth pin. if the drain- source voltage exceeds the voltage at the vdsth pin, ff2 will be pulled low . ? shorted motor w inding. a short across the motor phase winding is detected by monitoring the voltage across both the top and bottom fets in each phase. this fault will pull ff2 low. ? low load current. the sense amplifier output is monitored independently to allow detection of a low load current. this can be used to detect if an open load condition is present. if, during a commutation period, the output from the sense amplifier does not go above a minimum value, v csol , ff1 will go low. no further action will be taken. short fault operation. because motor capacitance may cause the measured voltages to show a fault as the phase switches, the voltages are not sampled until one t dead interval after the exter- nal fet is turned on. if a short-circuit fault occurs when esf = 0, the external fets are not disabled by the amt49413. under some conditions, some measure of protection will be provided by the internal current limit but in many cases, particularly for a short to ground, the current limit will provide no protection for the external fets. to limit any damage to the external fets or the motor, the amt49413 can either be fully disabled by the reset input or all fets can be switched off by pulling the coast input low. alternatively, setting esf = 1 will allow the amt49413 to dis- able the outputs as soon as the fault is detected. the fault will be latched until any of the following conditions occur: ? a phase commutation ? reset goes low ? coast goes low this will allow a running motor to coast to the next phase commutation without the risk of damage to the external power mosfets. low load current fault operation. no action is taken for a low load current condition. if the low load occurs due to an open circuit on a phase connection while the motor is running, the amt49413 will continue to commutate the motor phases accord- ing to the commutation truth table, table 2. in some cases, this will allow the motor to continue operating at a much reduced performance. the low load condition is checked during a commutation period and is only flagged at the next com- mutation event. the flag is cleared at the end of any subsequent- commutation period where no low load current fault is detected. if the motor stalls or is stationary, then the remaining phase con- nections will usually be insufficient to start rotating the motor. at start-up or after a reset, the low load condition is flagged until the first time the motor current exceeds the threshold value, v csol . this allows detection of a possible open phase from startup, even if the motor is not able to start running. note that a low load current condition can also exist if the motor being driven has no mechanical load. 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
12 table 1: fault action table ff1 ff2 fault action* esf = 0 esf = 1 0 0 undervoltage disable disable 0 0 overtemperature no action no action 0 0 logic fault disable disable 1 0 short to ground no action disable 1 0 short to supply no action disable 1 0 shorted motor winding no action disable 0 1 low load current no action no action 1 1 none no action no action *disable indicates that all gate outputs are low and all mosfets are turned off. table 2: commutation truth table* h1 h2 h3 dir gla glb glc gha ghb ghc sa sb sc 1 0 1 1 0 0 1 1 0 0 high z low 1 0 0 1 0 0 1 0 1 0 z high low 1 1 0 1 1 0 0 0 1 0 low high z 0 1 0 1 1 0 0 0 0 1 low z high 0 1 1 1 0 1 0 0 0 1 z low high 0 0 1 1 0 1 0 1 0 0 high low z 0 0 0 x 0 0 0 0 0 0 z z z 1 1 1 x 0 0 0 0 0 0 z z z 1 0 1 0 1 0 0 0 0 1 low z high 1 0 0 0 0 1 0 0 0 1 z low high 1 1 0 0 0 1 0 1 0 0 high low z 0 1 0 0 0 0 1 1 0 0 high z low 0 1 1 0 0 0 1 0 1 0 z high low 0 0 1 0 1 0 0 0 1 0 low high z table 3: input logic mode pwm brake coast reset decay mode of operation 0 0 1 1 1 fast pwm chop C current decay with opposite of selected drivers on 0 1 1 1 1 fast peak current limit C selected drivers on 1 0 1 1 1 slow pwm chop C current decay with both low-side drivers on 1 1 1 1 1 slow peak current limit C selected drivers on x x 0 1 1 n/a brake mode C all low-side gates on x x x 0 1 x coast mode C all gates off x x x x 0 x sleep mode C all gates off, low power state, 5 v off *x indicates dont care 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
13 power all supply connections to the amt49413 should have capaci- tors mounted between the supply pins and the ground pin. these capacitors will provide the transient currents which occur during switching and decouple any voltage transients on the pin from the main supply. vbb. decouple with at least a 100 nf ceramic capacitor mounted between the vbb pin and the agnd pin. a larger electrolytic capacitor, typically 10 f, in parallel with the ceramic capacitor is also recommended. vreg. supplies current for the gate-drive circuit. as the gates are driven high, they require current from an external capaci- tor connected to vreg to support the transients. this capacitor should be placed as close as possible to the vreg pin with the ground connection close to the agnd pin. its value should be at least 20 times larger than the bootstrap capacitor. the capacitor should have a very low series resistance (esr) and inductance (esl) to avoid large voltage drops during the initial transient. the optimum capacitor type is a high quality ceramic such as x7r. however, when the required capacitance is too large, an aluminium electrolytic capacitor may be used, with a smaller ceramic capacitor (100 nf) in parallel. v5. when the 5v regulator is used with an external pass transis- tor to provide power to other circuits, a 10 f decoupling capaci- tor should be connected between the v5 pin and agnd as close to the pins as possible. if an electrolytic capacitor is used, then a 100 nf ceramic capacitor should be added in parallel. to improve stability, a 100 nf capacitor also should be connected between the v5bd pin and agnd. if 5v is not required for external cir- cuits, the external pass transistor may be omitted, but in that case, v5 must connected directly to v5bd and decoupled with at least a 220 nf capacitor between v5 and agnd. agnd. the amt49413 has a single ground connection at the agnd pin. the design ensures that only the operating current for the controller stage passes through this pin. the charge and discharge current for the external fets does not pass though this pin. the agnd pin is the ground reference for the current trip threshold, the v ds monitor threshold, and the timing components. it should therefor be kept as quiet as possible. a suggested ground connection scheme is described in the layout section below. power dissipation. in applications where a high ambient tem- perature is expected the on-chip power dissipation may become a critical factor. careful attention should be paid to ensure the operating conditions allow the amt49413 to remain in a safe range of junction temperature. the power consumed, p tot , by the amt49413 can be estimated using the following formulas: p tot = p bias + p cpump + p switching , p bias = v bb i bb , where i bb is 3 ma, typical, and p cpump = (2 v bb Cv reg ) i av where v bb < 15 v, or p cpump = (v bb Cv reg ) i av where v bb > 15 v, and i av = q gate n f pwm , p switching = q gate v reg n f pwm ratio where n = 2 for slow decay, or n = 4 for fast decay, and ratio = 10 / (r gate + 10) bootstrap capacitors bootstrap capacitor selection. the value for c boot must be correctly selected to ensure proper operation of the device. if the value is too large, time will be wasted charging the capaci- tor, resulting in a limit on the maximum duty cycle and pwm frequency. if the value is too small, there can be a large voltage drop at the time when the charge is transferred from c boot to the mosfet gate. to keep the voltage drop small, q boot ? q gate . a factor of 20 is a reasonable value. to calculate c boot , the following formulas can be used: q boot = c boot v boot , = q gate 20, therefore c boot = q gate 20 / v boot the voltage drop on the c x pin as the mosfet is being turned on can be approximated by: v = q gate / c boot bootstrap charging. it is good practice to ensure that the high-side bootstrap capacitor, cboot, is completely charged applications information 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
14 before a high-side pwm cycle is requested. the minimum time required to charge the capacitor is approximated by: t charge(min) c boot v /250 ma at power-on, and when the drivers have been disabled for a long time, the cboot may be completely discharged. in these cases, v can be considered to be the full high-side drive voltage, 12 v . otherwise, v is the amount of voltage dropped during the char ge transfer, which should be 400 mv or less. the capacitor is charged whenever the s x pin is pulled low via a gl x pwm cycle, and current flows from vreg through the internal bootstrap diode circuit to cboot. bootstrap charge monitor. the amt49413 provides automatic bootstrap capacitor charge management. the boot- strap capacitor voltage for each phase, v bootx , is continuously checked to ensure that it is above the bootstrap undervoltage threshold, v bootuv . if v boot drops below this threshold, the amt49413 will turn on the necessary low-side fet until the v boot exceeds v bootuv plus the hysteresis, v bootuvhys . the minimum charge time is typically 7 s, but may be longer for very large values of the bootstrap capacitor (c boot >1000 nf). if v boot does not exceed v bootuv within approximately 200 s, an undervoltage fault will be flagged, as shown in table 1. pwm control the amt49413 has the flexibility to be used in many different motor control schemes. the internal pwm control can be used to provide fully integrated, closed-loop current control. alterna- tively, current-mode or voltage-mode control are possible using external control circuits with either the dir or the pwm input pins. internal pwm control. the internal pwm current control function is useful in applications where motor torque control or simple maximum current limitation is required. however, for motor speed control applications, it is usually better to use exter- nal pwm control either as a closed- or open-loop system. external pwm control. when external pwm control is used, it is possible to completely disable the internal pwm control circuit by connecting the rc pin to agnd. with the internal control disabled, however, care should be taken to avoid excessive current in the power fets because the amt49413 will not limit the current. short-circuit detection will still be available in case of faults. the output of the sense ampli- fier is also available, but provision must be made in the external control circuits to ignore (blank) the transients at the switching points. external and internal combined pwm control. where external pwm control is used but current limitation is still required, internal pwm current control can be used at the same time as external pwm control. to do so, usually the internal pwm frequency is set lower than the external pwm frequency. this allows the external pwm signal to dominate and synchro- nize the internal pwm circuit. it does this by discharging the timing capacitor, ct, when the pwm pin is low. when internal and external pwm control are used together, all control features of the amt49413 are available and active, including: dead time, current comparator, and comparator blanking. pwm frequency. should be set high enough to avoid any audi- ble noise, but low enough to ensure adequate charging of the boot capacitor, cboot. the external resistor rt and capacitor ct, connected in parallel from the rc pin to agnd, set the pwm frequency to approximately: f osc 1 / ( r t c t + t blank + t dead ) . r t should be in the range of 5 to 400 k. pwm blank. the timing capacitor, ct, also serves as the means to set the blank time duration. t blank . at the end of the pwm off-cycle, a high-side gate selected by the commutation logic turns on. at this time, large current transients can occur dur- ing the reverse recovery time of the intrinsic source drain body diodes of the external power mosfets. to prevent false tripping of the current-sense comparator, the output of the current com- parator is ignored during the blank time. the length of t blank is different for internal versus external pwm. it is set by the value of the timing capacitor, ct, according to the following formulas: for internal pwm: t blank (s) = 1260 c t (f), and for external pwm: t blank (s) = 2000 c t (f) . a nominal c t value of 680 pf will give a blanking time of 1.3 s for external pwm and 860 ns for internal pwm. the user must ensure that c t is large enough to cover the current-spike duration. 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
15 note that this blank time is only used to mask the internal cur- rent comparator. if the current sense amplifier output, csout, is being used in an external pwm control circuit, then it will be necessary to externally generate a blank time for that control loop. dead time. the potential for cross-conduction occurs with synchronous rectification, direction changes, pwm, or after a bootstrap capacitor charging cycle. to prevent cross-conduction in any phase of the power fet bridge, it is necessary to have a dead-time delay, t dead , between a high- or low-side turn-off and the next turn-on event. t dead is in the range of between 96 ns and 6.3 s, and is set by the value of a resistor, rdead , between the rdead pin and the gnd pin. the maximum dead time of typi - cally 6s can be set by leaving the rdead pin unconnected, or connected to the v5 pin. at 25c, the value of t dead (s) can be approximated by: t dead(nom) 0.1 + 33 / (5 + i dead ), i dead = 2000 / r dead where i dead is in a, and r dead is between 5 and 400 in k. the greatest accuracy is obtained with values of r dead between 10 and 100 k. the choice of power mosfet and external series gate resistance determines the selection of rdead. the dead time should be made long enough to cover the variation of the mosfet gate capacitance and the tolerances of the series gate resistance, both external and internal to the amt49413. synchronous rectification. to reduce power dissipation in the external mosfets, the amt49413 control logic turns on the appropriate low-side and high-side driver during the load current recirculation pwm-off cycle. synchronous rectification allows current to flow through the fet selected by the mode pin setting during the decay time, rather than through the source- drain body diode. the body diodes of the recirculating power fets conduct only during the dead time that occurs at each pwm transition. for internal current control using fast decay mode, reversal of load current is prevented by turning off synchronous rectification when a zero current level is detected. for external pwm control using fast decay mode, the load current will not be limited to zero but will rise to the set current limit in the reverse direction before disabling synchronous rectification. braking. the amt49413 provides dynamic braking by forc- ing all low-side mosfets on, and all high-side mosfets off. this effectively short-circuits the back emf of the motor, which forces a reverse current in the windings, and creating a breaking torque. during braking, the load current can be approximated by: i brake v bemf / r load because the load current does not flow through the sense resistor, rsense, during a dynamic brake, care must be taken to ensure that the power mosfet maximum ratings are not exceeded. it is possible to apply a pwm signal to the brake input to limit the motor braking current. however, because there is no measure - ment of this current, the pwm duty cycle must be determined for each set of conditions. typically the duty cycle of such a brake pwm input would start at a value which limits the current and then drops to 0%, that is, brake goes to low, to hold the motor stationary . setting reset = 1 and coast = 0 overrides brake and turns all motor bridge fet s off, coasting the motor. driving a full-bridge . the amt49413 may be used to drive a full-bridge (for example, a brush dc motor load) by hard-wiring a single state for the hall inputs and leaving the corresponding phase driver outputs floating. for example, with a configuration of h1 = h2 = 1, and h3 = 0, the outputs cc, ghc, sc, and glc would be floated, according to the commutation truth table, t able 2, which indicates a state of high-impedence (z) for sc with that hall input configuration. the dir input controls the motor rotation, while the pwm and mode inputs control the motor current behavior , as described in the input logic table, table 3. figure 2: internal pwm rc timing v rch rc 0 +v v rcl t rc t blank t os c ghx glx current trip points t dead t dead note: for reasons of clarity, t de ad is shown ex a gg erated. 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
16 circuit layout because this is a switch-mode application, where rapid current changes are present, care must be taken during layout of the application pcb. the following points are provided as guidance for layout (refer to figure 3). following all guidelines will not always be possible. however, each point should be carefully considered as part of any layout procedure. ground connection layout recommendations: 1. sensitive connections such as rdead and vdsth, which have very little ground current, should be referenced to the quiet ground, which is connected independently closest to the agnd pin. the components associated with these sensi- tive pins should never be connected directly to the supply common or to the power ground; they must be referenced directly to the agnd pin. 2. supply decoupling for the supply pins vbb, vreg, and v5 should be connected to controller supply ground, which is connected independently, close to the agnd pin. the decoupling capacitors should also be connected as close as possible to the corresponding supply pin. 3. the oscillator timing components can be connected to quiet ground or controller supply ground. they should not be connected to the supply common or the power ground. 4. the exposed thermal pad on the package should be con- nected to the agnd pin and may form part of the controller supply ground. 5. if the layout space is limited, then the quiet ground and the controller supply ground may be combined, provided that the ground return of the dead-time resistor , rdead, is close to the agnd pin.6. the agnd pin should be connected by an independent low impedance trace to the supply com- mon at a single point. 7. check the peak voltage excursion of the transients on the lss pin with reference to the agnd pin using a close- grounded (tip and barrel) probe. if the voltage at lss exceeds the absolute maximum specified in this datasheet, add additional clamping, capacitance or both between the lss pin and the agnd pin. other layout recommendations: 1. gate char ge drive paths and gate discharge return paths may carry large transient current pulses. therefore, the traces from ghx, glx, sx, and lss should be as short as possible to reduce the inductance of the circuit trace. 2. provide an independent connection from lss to the common point of the power bridge. it is not recommended to connect lss directly to the agnd pin, as this may inject noise into sensitive functions such as the dead-timer. the lss connec- tion should not be used for the csp connection. 3. the inputs to the sense amplifier , csp and csn, should be independent traces and for best results should be matched in length and route. 4. minimize stray inductance by using short, wide copper runs at the drain and source terminals of all power fet s. this includes motor lead connections, the input power bus, and the common source of the low-side power fets. this will minimize voltages induced by fast switching of large load currents. 5. consider the use of small (100 nf) ceramic decoupling capacitors across the source and drain of the power fet s to limit fast transient voltage spikes caused by trace inductance. 6. ensure that the test pin is connected to agnd. this pin is used for production test only. the above are only recommendations. each application is differ- ent and may encounter different sensitivities. a driver running with a few amperes will be less susceptible than one running with 150 a, and each design should be tested at the maximum current, to ensure any parasitic effects are eliminated. 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
17 figure 3: supply and ground connections sa gha gla lss supply common + supply moto r vbb vreg v5 ag nd rc vdst h rd ead qui e t gr ound c ontr oller suppl y gr ound pow er gr ound amt49413 ghb ghc glb glc sb sc v drain optional components to limit lss tr ansients rsense 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
18 vdrain 19 v supplies 19 v 20 v vbb 19 v 19 v 20 v v5 6 v v5bd 10 v cp 1 18 v cp 2 h1 h2 h3 3 k? 8 v 8.5 v 100 k? v5 hall sensor inputs co ast esf brake dir pw m mode 3 k? 8 v 8.5 v logic inputs rc 1 k? 8 v 8.5 v o scillator rc pin v5 re f 3 k? 8 v 8.5 v ref vdst h 1 k? 8 v 8.5 v v ds monitor threshold input 40 k? ff1 ff2 8 v fault output 100 ? 8 v rd ead 100 ? 8 v 8.5 v rdead 2 v r eset 3 k? 6 v 6 v reset input 50 k? ta cho diro 8 v logic output 100 ? 8 v v5 cs n cs p 22v 22v vreg 4 k? 4 k? 72 k? 76k 8.5 v 8.5 v csout 2v 32.4 k? 4.6 k? 160a 160a sense amplifier cx 18 v 18 v ghx sx glx lss 19 v 20 v 18 v 18 v 20 v 18 v vreg 18 v gate drive outputs figure 4: input and output structures 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
19 ev package pinout diagram and terminal list number name description 1 n.c. no connection 2 reset control for sleep mode 3 v5bd 5v regulator base drive 4 v5 5v regulator reference 5 ff2 fault flag 2 6 ff1 fault flag 1 7 tacho speed output 8 brake brake input 9 dir direction control input 10 h1 hall sensor input 11 h2 hall sensor input 12 h3 hall sensor input 13 n.c. no connection 14 pwm control input 15 mode decay control input 16 rc pwm oscillator control input 17 test test pin; tie to agnd 18 rdead dead time setting 19 csout current sense output 20 ref current limit setting 21 csn current sense input C 22 csp current sense input + 23 vdsth fault threshold voltage 24 vdrain high-side drain voltage sense number name description 25 sc motor connection phase c 26 ghc high-side gate drive phase c 27 cc bootstrap capacitor phase c 28 sb motor connection phase b 29 ghb high-side gate drive phase b 30 cb bootstrap capacitor phase b 31 sa motor connection phase a 32 gha high-side gate drive phase a 33 ca bootstrap capacitor phase a 34 glc low-side gate drive phase c 35 glb low-side gate drive phase b 36 gla low-side gate drive phase a 37 n.c. no connection 38 lss low-side source 39 esf enable stop on fault input 40 vreg gate drive supply output 41 agnd analog ground 42 cp1 pump capacitor 43 cp2 pump capacitor 44 diro direction output 45 vbb supply voltage 46 coast coast input 47 n.c. no connection 48 n.c. no connection C pad thermal dissipation, tie to agnd terminal list table 36 35 34 33 32 31 30 29 28 27 26 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 nc nc coast vbb diro cp2 cp1 agnd vreg esf lss nc nc pwm mode rc test rdead csout ref csn csp vdsth vdrain gla glb glc ca gha sa cb ghb sb cc ghc sc nc reset v5bd v5 ff2 ff1 tacho brake dir h1 h2 h3 pad 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
20 package outline drawing for reference only ? not for tooling use (reference dwg-2867) dimensions in millimeters not to scale exact case and lead con?guration at supplier discretion within limits shown c seating plane c 0.08 49x 48 48 2 1 1 2 a a b c d d c 0.50 bsc 7.00 bsc 7.00 bsc 0.90 nom 0.40 nom b 0.25 5.15 0.10 5.15 0.10 0.50 1.00 4x0.20 min 7.0 7.0 48 2 1 0.30 5.15 5.15 +0.30 -0.18 pcb layout reference view terminal #1 mark area exposed thermal pad (reference only , terminal #1 identi?er appearance at supplier discretion) reference land pattern layout (reference ipc7351 qfn50p700x700x100-49m); all pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and pcb layout tolerances; when mounting on a multilayer pcb, thermal vias at the exposed thermal pad land can improve thermal dissipation (reference eia/jedec standard jesd51-5) coplanarity includes exposed thermal pad and terminals figure 5: package ev, 48 terminal qfn with exposed thermal pad 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com
21 for the latest version of this document, visit our website: www.allegromicro.com revision history number date description C october 26, 2016 initial release copyright ?2016, allegro microsystems, llc allegro microsystems, llc reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. before placing an order, the user is cautioned to verify that the information being relied upon is current. allegros products are not to be used in any devices or systems, including but not limited to life support devices or systems, in which a failure of allegros product can reasonably be expected to cause bodily harm. the information included herein is believed to be accurate and reliable. however, allegro microsystems, llc assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. 3-phase bldc controller and mosfet driver amt49413 allegro microsystems, llc 115 northeast cutoff worcester, massachusetts 01615-0036 u.s.a. 1.508.853.5000; www.allegromicro.com

▲Up To Search▲

Price & Availability of AMT49413GEVATR

	To Download AMT49413GEVATR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .