typical performance data maximum ratings operating temperature -55c to 100c storage temperature -55c to 100c control current 30ma 0 20 40 60 80 100 0 200 400 600 800 1000 isolation (db) frequency (mhz) gas -2+ isolation in-out in-con GAS-2+ 50 ? bi-phase 10 to 1000 mhz attenuator/switch rev. d m153690 GAS-2+ wp/td/cp/am 151112 plug-in 1 10 100 0.0001 0.001 0.01 0.1 1 10 100 attenuation (db) control current (ma) gas -2+ attenuation 10 mhz 500 mhz 1000 mhz features ? wideband, 10 to 1000 mhz ? rugged shielded case applications ? bi-phase modulator ? electronic attenuator pin connections input 1 output 8 control 3,4^ ground 2,5,6,7 case ground 2,5,6,7 0 2 4 6 8 10 0 200 400 600 800 1000 insertion loss (db) frequency (mhz) gas -2+ insertion loss suggested control port biasing confguration case style: a05 ^ pins must be connected together externally outline drawing outline dimensions ( ) a b c d e f .770 .800 .240 .250 .370 .400 19.56 20.32 6.10 6.35 9.40 10.16 g h j k wt .200 .20 .14 .031 grams 5.08 5.08 3.56 0.79 3.7 inch mm attenuator/switch electrical specifcations l = low range [f l to 10 f l ] m = mid range [10 f l to f u /2] u = upper range [f u /2 to f u ] m = [ 2 f l to f u /2] performance specifcations apply for input power up to 10 db below stated 1 db compression. frequency (mhz) insertion loss (db) 20 ma max. input pwr (dbm) 20 ma in-out isolation (db) 0 ma bi-phase x ( 20 ma) typ. ? amp (db) phase (deg.) deviation from 180 in con mid-band m total range 1 db no l m u total total f l -f u ty p. max. ty p. max. compr. damage ty p. min. ty p. min. ty p. min. m range m range 10-1000 dc-0.05 4.3 6 5.2 8.5 20 25 55 40 35 25 28 20 0.10 0.3 1.5 3.0 electrical schematic 10.0 3.50 0.025 0.01 180.00 70 47 12.3 0.0000 71.8 43.8 38.2 -37.1 96.0 63.6 3.6 2.9 7.5 19.9 3.52 0.015 0.01 180.00 68 40 12.7 0.0003 63.7 44.2 38.1 -34.3 93.2 62.4 3.6 2.9 7.5 39.7 3.61 0.008 0.01 179.90 67 35 12.6 0.0004 55.7 43.8 38.1 -12.5 86.0 57.8 3.6 2.9 7.5 59.5 3.63 0.006 0.01 179.90 65 31 12.5 0.0016 51.2 43.3 38.1 -8.5 80.1 52.8 3.6 2.8 7.4 79.3 3.66 0.006 0.01 179.90 64 29 12.5 0.0057 45.4 41.1 36.8 -4.6 55.5 35.7 3.6 2.8 7.3 86.7 3.68 0.006 0.01 179.90 63 28 12.5 0.0105 41.5 38.6 35.6 -1.2 42.6 23.4 3.5 2.8 7.1 99.1 3.73 0.006 0.01 179.90 62 27 12.4 0.0161 38.3 36.0 33.7 1.5 34.4 12.9 3.5 2.8 6.9 163.5 3.95 0.006 0.01 179.80 58 23 12.3 0.0286 33.9 31.8 30.1 3.6 24.5 0.6 3.4 2.7 6.6 237.7 4.03 0.007 0.01 179.70 55 20 12.1 0.0437 30.3 28.4 27.1 4.3 20.7 -5.6 3.3 2.6 6.2 314.4 4.05 0.008 0.01 179.37 52 18 12.0 0.0734 26.2 24.4 23.2 5.1 16.3 -9.9 3.1 2.4 5.6 391.2 4.23 0.012 0.02 179.60 50 17 12.1 0.1029 23.6 21.8 20.8 5.0 14.4 -11.4 2.9 2.3 5.2 467.9 4.36 0.017 0.04 179.60 48 17 12.3 0.1510 20.7 19.1 18.2 5.0 12.8 -11.9 2.7 2.1 4.7 500.1 4.38 0.021 0.04 179.60 47 17 12.4 0.2540 17.1 15.6 15.1 4.6 10.4 -11.1 2.4 1.8 4.0 542.1 4.48 0.027 0.06 179.50 46 17 12.5 0.3743 14.6 13.3 13.1 4.3 9.0 -9.9 2.1 1.6 3.6 618.9 4.63 0.040 0.10 179.50 44 18 12.6 0.6438 11.5 10.6 10.8 3.5 6.9 -7.5 1.7 1.3 3.1 695.6 4.90 0.053 0.13 179.60 43 20 12.1 0.9350 9.7 9.1 9.6 3.0 5.4 -6.0 1.5 1.2 2.9 772.3 5.02 0.064 0.16 179.38 41 23 10.8 1.7496 7.2 7.2 8.2 2.0 3.6 -3.6 1.2 1.1 2.7 846.6 5.51 0.073 0.16 179.70 41 21 9.1 2.6537 5.5 5.9 7.3 1.3 1.9 -1.8 1.2 1.3 2.7 923.3 6.21 0.087 0.21 179.80 40 17 7.5 7.3045 4.3 4.9 6.7 0.5 0.6 -0.7 1.4 1.5 2.6 1000.0 7.06 0.093 0.36 180.40 40 14 6.3 15.1437 3.6 4.5 6.4 0.1 0.1 -0.1 1.5 1.6 2.6 typical performance data freq. (mhz) i. loss (db) at 20ma control, 20ma isolation (db) (in-out) (in-con) input r. loss (db) control current (ma) attenuation (db) phase ? ref at 15ma ctrl input vswr 10 mhz 500 mhz 1000 mhz 10 mhz 500 mhz 1000 mhz 10 mhz 500 mhz 1000 mhz ?amp (db) ?phase (deg.) x x x x x x deg. deg. deg. permanent damage may occur if any of these limits are exceeded. notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com +rohs compliant the +suffix identifies rohs compliance. see our web site for rohs compliance methodologies and qualifications
|
