ntc inrush current limiter applications control of the inrush current in switching power supplies, fuorescent lamp, inverters, motors, etc. thermometrics thermistors features ? ul approval (ul 1434 file# e82830) ? small physical size offers design-in benefts over larger passive components ? low cost, solid state device for inrush current suppression ? best-in-class capacitance ratings ? low steady resistance and accompanying power loss ? excellent mechanical strength ? wide operating temperature range: -58f to 347f (-50c to 175c) ? suitable for pcb mounting ? available with kinked or straight leads and tape and reel to eis rs-468a for automatic insertion a mphenol advanced sensors
inrush current limiters in switching power supplies the problem of current surges in switch-mode power supplies is caused by the large flter capacitors used to smooth the ripple in the rectifed 60 hz current prior to being chopped at a high frequency. the diagram above illustrates a circuit commonly used in switching power supplies. in the circuit above the maximum current at turn-on is the peak line voltage divided by the value of r; for 120 v, it is approximately 120 x 2/r i . ideally, during turn-on r i should be very large, and after the supply is operating, should be reduced to zero. the ntc thermistor is ideally suited for this application. it limits surge current by functioning as a power resistor which drops from a high cold resistance to a low hot resistance when heated by the current fowing through it. some of the factors to consider when designing ntc thermistor as an inrush current limiter are: ? maximum permissible surge current at turn-on ? matching the thermistor to the size of the flter capacitors ? maximum value of steady state current ? maximum ambient temperature ? expected life of the power supply maximum surge current the main purpose of limiting inrush current is to prevent components in series with the input to the dc/dc convertor from being damaged. typically, inrush protection prevents nuisance blowing of fuses or breakers as well as welding of switch contacts. since most thermistor materials are very nearly ohmic at any given temperature, the minimum no-load resistance of the thermistor is calculated by dividing the peak input voltage by the maximum permissible surge current in the power supply (v peak/imax surge ). energy surge at turn-on at the moment the circuit is energized, the flter caps in a switcher appear like a short circuit which, in a relatively short period of time, will store an amount of energy equal to 1/2cv 2 . all of the charge that the flter capacitors store must fow through the thermistor. the net effect of this large current surge is to increase the temperature of the thermistor very rapidly during the period the capacitors are charging. the amount of energy generated in the thermistor during this capacitor-charging period is dependent on the voltage waveform of the source charging the capacitors. however, a good approximation for the energy generated by the thermistor during this period is 1/2cv 2 (energy stored in the flter capacitor). the ability of the ntc thermistor to handle this energy surge is largely a function of the mass of the device. this logic can be seen in the energy balance equation for a thermistor being self-heated: ~ dc/dc converter typical power supply circuit input energy = energy stored + energy dissipated or in differential form: pdt = hdt + (t C t a )dt where: p = power generated in the ntc t = time h = heat capacity of the thermistor t = temperature of the thermistor body = dissipation constant t a = ambient temperature during the short time that the capacitors are charging (usually less than 0.1 second), very little energy is dissipated. most of the input energy is stored as heat in the thermistor body. in the table of standard inrush limiters there is listed a recommended value of maximum capacitance at 120 v and 240 v. this rating is not intended to defne the absolute capabilities of the thermistors; instead, it is an experimentally determined value beyond which there may be some reduction in the life of the inrush current limiter. maximum steady-state current the maximum steady-state current rating of a thermistor is mainly determined by the acceptable life of the fnal products for which the thermistor becomes a component. in the steady-state condition, the energy balance in the differential equation already given reduces to the following heat balance formula: power = i 2 r = (t C t a ) as more current fows through the device, its steady-state operating temperature will increase and its resistance will decrease. the maximum current rating correlates to a maximum allowable temperature. in the table of standard inrush current limiters is a list of values for resistance under load for each unit, as well as a recommended maximum steady-state current. these ratings are based upon standard pc board heat sinking, with no air fow, at an ambient temperature of 77 (25c). however, most power supplies have some air fow, which further enhances the safety margin that is already built into the maximum current rating. to derate the maximum steady state current for operation at elevated ambient temperatures, use the following equation: i derated = (1.1425C0.0057 x t a ) x i max @ 77f (25c)
c x max ** ( farads) equation constants for resistance under load *** approximate resistance load at % maximum rated type resistance @ 25c () 25% *max. steady state current (amps rms) max. disc dia. in (mm) max. disc thick. in (mm) @120 (vac rms) @240 (vac rms) max. energy (joules) x y current range min i max i 25% 50% 75% 100% dissip. constant (mw/c) time constant (sec.) max . current flow @ 25c and 240 v rms (amps) cl-11 0.7 12 0.77 (19.56) 0.22 (5.59) 2700 675 19.44 0.5 -1.18 4<1<12 0.14 0.06 0.04 0.03 25 100 457 cl-21 1.3 8 0.55 (13.97 0.21 (5.33) 800 200 5.76 0.6 -1.25 3<1<8 0.25 0.11 0.06 0.04 15 60 246 cl-30 2.5 8 0.77 (19.56) 0.22 (5.59) 6000 1500 43.20 0.81 -1.25 2.5<1<8 0.34 0.14 0.09 0.06 25 100 128 cl-40 5 6 0.77 (19.56) 0.22 (5.59) 5200 1300 37.44 1.09 -1.27 1.5<1<6 0.65 0.27 0.16 0.11 25 100 64 cl-50 7 5 0.77 (19.56) 0.26 (6.60) 5000 1250 36.00 1.28 -1.27 1.5<1<5 0.96 0.40 0.24 0.17 25 120 46 cl-60 10 5 0.77 (19.56) 0.22 (5.59) 5000 1250 36.00 1.45 -1.3 1.2<1<5 1.08 0.44 0.26 0.18 25 100 32 cl-70 16 4 0.77 (19.56) 0.22 (5.59) 5000 1250 36.00 1.55 -1.26 1<1<4 1.55 0.65 0.39 0.27 25 100 20 cl-80 47 3 0.77 (19.56) 0.22 (5.59) 5000 1250 36.00 2.03 -1.29 0.5<1<3 2.94 1.20 0.71 0.49 25 100 7 cl-90 120 2 0.93 (23.62) 0.22 (5.59) 5000 1250 36.00 3.04 -1.36 0.5<1<2 7.80 3.04 1.75 1.18 30 120 3 cl-101 0.5 16 0.93 (23.62) 0.22 (5.59) 4000 1000 28.80 0.44 -1.12 4<1<16 0.09 0.04 0.03 0.02 30 120 640 cl-110 10 3.2 0.40 (10.16) 0.17 (4.32) 600 150 4.32 0.83 -1.29 0.7<1<3.2 1.11 0.45 0.27 0.19 8 30 32 cl-120 10 1.7 0.40 (10.16) 0.17 (4.32) 600 150 4.32 0.61 -1.09 0.4<1<1.7 1.55 0.73 0.47 0.34 4 90 32 cl-130 50 1.6 0.45 (11.43) 0.17 (4.32) 600 150 4.32 1.45 -1.38 0.4<1<1.6 5.13 1.97 1.13 0.76 8 30 6 cl-140 50 1.1 0.45 (11.43) 0.17 (4.32) 600 150 4.32 1.01 -1.28 0.2<1<1.1 5.27 2.17 1.29 0.89 4 90 6 cl-150 5 4.7 0.55 (13.97) 0.18 (4.57) 1600 400 11.52 0.81 -1.26 1<1<4.7 0.66 0.28 0.17 0.12 15 110 64 cl-160 5 2.8 0.55 (13.97) 0.18 (4.57) 1600 400 11.52 0.6 -1.05 0.8<1<2.8 0.87 0.42 0.28 0.20 9 130 64 cl-170 16 2.7 0.55 (13.97) 0.18 (4.57) 1600 400 11.52 1.18 -1.28 0.5<1<2.7 1.95 0.80 0.48 0.33 15 110 20 cl-180 16 1.7 0.55 (13.97) 0.18 (4.57) 1600 400 11.52 0.92 -1.18 0.4<1<1.7 2.53 1.11 0.69 0.49 9 130 20 CL-190 25 2.4 0.55 (13.97) 0.18 (4.57) 800 200 5.76 1.33 -1.34 0.5<1<2.4 2.64 1.04 0.61 0.41 15 110 13 cl-200 25 1.7 0.55 (13.97) 0.18 (4.57) 800 200 5.76 0.95 -1.24 0.4<1<1.7 2.74 1.16 0.70 0.49 9 130 13 cl-210 30 1.5 0.40 (10.16) 0.2 (5.08) 600 150 4.32 1.02 -1.35 0.3<1<1.5 3.83 1.50 0.87 0.59 8 30 11 type cl specifcations ntc discs for inrush current limiting description disc thermistor with uninsulated lead-wires. options ? for kinked leads, add suffx a ? for tape and reel, add suffx b ? other tolerances in the range 0.7 to 120 ? other tolerances, tolerances at other temperatures ? alternative lead lengths, lead materials, insulations data *maximum rating at 77f (25oc) or i derated = (1.1425C0.0057 x t a ) x i max @ 77f (25c) for ambient temperatures other than 77f (25oc). **maximum ratings ***r 0 =x1 y where x and y are found in the table below
selection criteria for thermometrics cl-products 1. i max - thermometrics cls are rated for maximum steady state current. the maximum steady current is mainly determined by the acceptable life of the fnal products for which the thermistor b ecomes a component. the differential equation pdt = hdt + (t C t a )dt reduces to power = i 2 r = (t C t a ). an example in the case of a 100 watt power supply with an effciency rating of 80%, 100% load is calculated to be 125 watts. the maximum input current is calculated from the minimum supply voltage. for a standard 120v supply, this could be rated as low a t 110v. therefore, input current would be calculated by 125 watts/110 v = 1.14 amps. selection of the cl should have an i max rating of at least 1.14 amps. 2. the second step of selection of the cl is to understand the desired maximum inrush current allowable. this is generally specifced by the components in line of the cl, such as the diode bridge. in the case of the diode bridge rated at 200 amps, one would should select a cl that would limit max surge current to 50% of the rating, therefore limit surge to a maximum of 100 amps. the listed maximum current fow is rated at 25c, so derating is required if the ambient temperture is greater than 25c. 3. the next selection of criteria for the cl is to understand the bulk capa citance of the device to be protected. on power, the bulk capacitance of the device appears as a short to the system. the designer needs to understand the bulk capacitance at the rms voltage rating of the system. assuming the input capacita nce is approximately 500 fds, the selection of the cl needs to be able to absorb input energy. using the above criteria, the selection of the cl provides multiple solu tions. one would opt for the smallest size cl to achieve the required protection. the selection criteria is as follows: 1. i max >1.14 amps 2. max allowable inrush current 100 amps 3. bulk capacitance listed as 500 fd 4. choose smallest physical size that will allow protection for the device. criteria indicates that either the cl-150 or cl-160 would be suitable for the application. in the case of the cl-150 less heat is dissipated allowing the operating resistance to drop but at a higher te mperature. this increases effciency of the system but may lead to shorter component life. aas-920-325d-03/2014 www.amphenol-sensors.com ? 2014 amphenol corporation. all rights reserved. specifcations are subject to change without notice. other company names and product names used in this document are the registered trademarks or trademarks of their respective owners. a mphenol advanced sensors
|