features ? for surface mounted applications ? low profile package ? built-in strain relief ? easy pick and place ? plastic package has underwriters laboratory flammability classification 94v-o utilizing ? low forward drop ? high temperature soldering : 260c /10 seconds at terminals mechanical data case: smf molded plastic terminals: solder plated, solderable per mil-std-750, method 2026 polarity: indicated by cathode band standard packaging: 12mm tape (eia-481) gpp sur face mount rectifier voltage- 50 to 1000 volts current - 1.0 amperes maximum ratings and electrical characteristics ratings at 25c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20%. maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current, at t l =75c peak forward surge current 8.3ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage at 1.0a maximum dc reverse curren a =25c at rated dc blocking voltage a =125c maximum reverse recovery time(note 1) t j =25c typical junction capacitance (note 2) maximum thermal resistance(note 3) operating and storage temperature range 1.0 30 1.1 5.0 2.5 12 75 -55 to +150 v v v a a v a s p f unit c/ w 1. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a 2. measured at 1 mhz and applied v r = 4.0 volts. 3. 8.0 mm 2 ( .013mm thick ) land areas. 100 a c smf unit: inch ( mm ) v rrm v rms v dc i(av) i fsm v f i r t rr c j r ja t j, t stg data sheet G1A 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 g1b g1d g1g g1j g1k g1m semiconductor http://www.yeashin.com 1 rev.03 20150105 G1A g1m t t notes: ? thru sy mbols 0.035(0.90)typical 0.189(4.80) 0.009(0.22) 0.006(0.15) 0.173(4.40) 0.141(3.60) 0.110(2.80) 0.052(1.30) 0.056(1.43) 0.126(3.20) 0.095(2.40) 0.043(1.10) 0.054(1.38) 0.87max (2.20max) 0.82min (1.27min) 0.050min (1.27min) 0.201ref (5.1ref)
3.0 2.0 1.0 0 051 57 0 100 40 20 10 4.0 2.0 1.0 0.4 0.2 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 25 20 15 10 5 0 1 2 6 10 20 40 60 100 0.4 0.5 1.5 2.5 10 0.1 1.0 100 1000 1 2 5 10 20 50 100 10 0.1 1.0 100 1 2 5 10 20 50 100 0.01 100 1.0 0.01 20 40 60 80 100 120 140 0.001 0.1 0 10 30 fig.1-forward current derating curve fig.2-typical instantaneous forward characteristics fig.4-maximum non-repetitive peak forward surge current fig.3-typical reverse characteristics fig.5-transient thermal impedance fig.6-typical junction capacitance lead temperature, c o instantaneous forward voltage, volts ,tnerrucdrawrofsuoenatnatsni serepma ,tnerrucdrawrofegareva serepma ,tnerrucesreversuoenatnatsni serepmaorcim tnerrucegrusdrawrofkaep serepma, fp,ecnaticapac )w/c(ecnadepmilamreht o number of cycles at 60hz percent of peak reverse voltage, % heating time(sec) units mounted on 20in2 (5.4mm)+0.5mil inches(0.013mm) thick copper land areas single phase half wave 60hz resistive or inductive load p.c.b mounted on 0.315 x 0.315" (8.0 x 8.0mm) copper pad areas t = 25 c f = 1.0mhz vsig = 50mvp-p j o 8.3ms single half sine-wave jedec method t = 75 c j o t = 100 c j o t = 25 c j o reverse voltage, volts http://www.yeashin.com 2 rev.03 20150105 G1A g1m thru rating and characteris tic curves
|
