gamewell-fci 12 clintonville road, northford, ct 06472-1610 usa ? tel: (203) 484-7161 ? fax: (203) 484-7118 specifications are for inform ation only, are not intended for installation pur poses, and are subject to change without notice. no responsibility is assumed by gamewell-fci for their use. ?2013 by honeywell international inc. all rights reserved. www.gamewell-fci.com 9020-0623 rev. f page 1 of 2 velociti ? series abd-2f and abd-rt2f single-ended reflected type beam smoke sensor 3023594 s1913 signaling approved fm 7260-1703:0120 mea approved fdny coa #:219-02-e vol. vi description the gamewell-fci velociti ? series, abd-2f and address- able projected beam smoke sensor is uniquely suited to sense smoke in hostile envir onments or open areas with high ceilings where spot-type sensors are unsuitable or difficult to install and maintain. it is intended for use in the signaling line circuits with the following sub-assemblies. ? e3 series ? , ili-mb-e3 and ili-s-e3 (velociti mode only) ? s3 series, slc-pm (signaling line circuit-personality module) the abd-2f consists of a combination transmitter/ receiver unit and a reflector. when smoke enters the path between the unit and the reflector, it causes a reduction in the signal, and when the smoke level reaches the prede- termined threshold, an alarm results. a unique single-ended reflective design offers simpler installation than the traditional transmitter and receiver types of beam sensors. ali gnment is swiftly accomplished via an optical sight and a 2-digit signal strength meter inte- gral with the product. listed for operation from ?22 f to 131 f, the abd-2f can be installed in garages, ware- houses and other hostile envi ronments where temperature extremes exceed the capabi lity of spot-type sensors. the velociti ? series uses a communication protocol that substantially increases t he speed of communication between the sensors and gamewell-fci analog address- able fire alarm controls. these devices operate in a grouped fashion. if one of the devices in the group changes status, the panel?s microprocessor stops the group poll and concentrates on the single device. the net effect is response speed up to five times greater than ear- lier designs. the unit has four standard sens itivity selections along with two acclimate settings. when either of the two acclimate settings are selected, the se nsor will automatically adjust its sensitivity using the adv anced software algorithms to select the optimum sensitivity for the specific environment. velociti ? and e3 series ? are registered trademarks of honeywell international inc. features ? includes a single-ended, reflective design. ? has six user-selectable sensitivity levels. ? spans a 16 to 328 foot (4.9 to 99.9 m) detection range. ? compatible with the e3 series ? ili-mb-e3 and ili-s-e3 or the s3 series, slc-pm. ? contains an integral sensitivity test feature (abd-2sf). ? designed with a digital display - no special tools required. ? provides a user-friendly alignment procedure. ? offers an integral automatic gain control that compen- sates for signal deterioration from dust build-up. ? available with an optional remote test station. abd-2f/rt2f
gamewell-fci 12 clintonville road, northford, ct 06472-1610 us a ? tel: (203) 484-7161 ? fax: (203) 484-7118 9020-0623 rev. f page 2 of 2 www.gamewell-fci.com description (continued) the abd-rt2f is equipped with an integral sensitivity test feature consisting of a test filter attached to a servo motor inside the sensor optics. the abd-rt2f requires an addi- tional, external power supply. using the remote test station model rts151, the motor moves the filter in the path of the light beam, thereby serving as an accurate test of the receiver sensitivity. this te st feature allows the user to quickly and easily meet the annual maintenance and test requirements of nfpa 72. specifications operating temperature range: -22 f to 131 f (-30 c to 55 c) operating humidity range: 10% to 93 rh non-condensing dimensions: detector: 10? h x 7.5? w x 3.3? d (25.4 h x 19 w x 8.4 d cm) reflector: 16-230 ft. (4.9 x 70.1 m) 7.9? h x 9.1? w (20 h x 23 w cm) voltage range: 15 to 32 vdc alarm current: 8.5 ma max. standby current: 2 ma max. avg. @ 24 vdc ordering information part number description b210lp flanged mounting base. dimensions: 6.1? (15.5 cm) diameter. b210lpbp flanged mounting base bulk pack. dimensions: 6.1 (15.5 cm) diameter. abd-rt2f single-ended smoke sensor with integral sensitivity test. beamlrk long range accessory kit (required for applications with a range over 230 ft. (70m) . BEAMMMK multi-mount kit (provides ceiling or wall mount capability with increased angular adjustment). beamsmk surface mount kit. rts151 remote test station. rts151key remote test station with key lock.
|
