electrical specifcations maximum ratings pin connections features operating temperature -45c to 85c storage temperature -55c to 100c absolute max. control current 10ma absolute max. rf input level +15 dbm applications ? variable gain amplifer ? feed forward amps ? alc circuits ? frequency range, 600-1200 mhz ? ip3, 48 dbm typ. ? minimum current at min. attenuation ? low insertion loss ? protected by us patent 7,030,713 rf in 2 v control 1 8 v control 2 4 rf out 6 ground 1,3,5,7 case style: gf995 * input ip3 tested with two tones separated by 1 mhz at 7 dbm each and 0v control voltage. ** using recommended control port biasing. freq insertion loss attenuation ip3* return loss control (mhz) (db) (db) (dbm) (db) voltage** 0v control voltage input output (v) min. max. typ. max. typ. min. typ. min. typ. typ. 600-1200 1.0 2.2 25 20 48 40 20 20 0-6 equivalent schematic of dut VACC-09 + attenuation vs. frequency vs. control voltage 0 10 20 30 40 50 60 600 700 800 900 1000 1100 1200 frequency(mhz) attenuation(db) 0v 0.5v 0.6v 0.7v 0.8v 0.9v 1v 1.1v 1.128v VACC-09 + typical attenuation at 900mhz 0 5 10 15 20 25 30 35 40 0123456 control voltage (v) attenuation(db) outline drawing pcb land pattern suggested layout, tolerance to be within .002 outline dimensions ( ) inch mm a b c (max) d e f g h j .150 .150 .065 .008 .036 .018 .062 .028 .022 3.81 3.81 1.65 0.20 0.91 0.46 1.57 0.71 0.56 k l m n p q r s t wt. .017 .014 .036 .018 .062 .028 .037 .017 .014 gram 0.43 0.36 0.91 0.46 1.57 0.71 0.94 0.43 0.36 .06 permanent damage may occur if any of these limits are exceeded. 50? 600 to 1200 mhz voltage variable attenuator surface mount VACC-09+ rev. c m151108 VACC-09+ edb-040303 bcell/rs/cp 161211 page 1 of 3 2 6 84 +rohs compliant the +suffix identifies rohs compliance. see our web site for rohs compliance methodologies and qualifications notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
VACC-09 + input return loss vs. frequency vs. control voltage 15 20 25 30 35 40 45 50 55 600 700 800 900 1000 1100 1200 frequency(mhz) return loss(db) 0v 0.5v 0.6v 0.7v 0.8v 0.9v 1v 1.1v VACC-09 + output return loss vs. frequency vs. control voltage 15 20 25 30 35 40 45 600 700 800 900 1000 1100 1200 frequency(mhz) return loss(db) 0v 0.5v 0.6v 0.7v 0.8v 0.9v 1v 1.1v demo board mcl p/n: tb-250 suggested pcb layout (pl-148) recommended control port biasing confguration dut c3 c1 r1 r2 v control rf out dc block dc block c4 c2 4 8 6 2 r1, r2: 2k ohm chip resistor (0402, as close as possible to the device) c1, c2: 0.01 uf chip capacitor (0603) c3 c4: 6.8 pf chip capacitor (0603) rf in page 2 of 3 VACC-09+ performance curves notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
VACC-09 + insertion loss vs. input power @ 900mhz -70 -60 -50 -40 -30 -20 -10 0 5 10 15 20 25 input power(dbm) insertion loss(db) 1v 1.05v 1.1v 1.15v 1.2 1.25 1.3 1.35 1.4 1.45 1.5 1.55v 1.6v 1.65v VACC-09 + ip3 vs. control voltage vs. frequency @ 85c 0 10 20 30 40 50 60 0 0.2 0.4 0.6 0.8 1 1.2 control voltage(v) ip3(dbm) ip3 @ 600mhz ip3 @ 900mhz ip3 @ 1200mhz VACC-09 + ip3 vs. control voltage vs. frequency @ -45c 0 5 10 15 20 25 30 35 40 45 50 0 0.2 0.4 0.6 0.8 1 1.2 control voltage(v) ip3(dbm) ip3 @ 600mhz ip3 @ 900mhz ip3 @ 1200mhz VACC-09 + ip3 vs. control voltage vs. frequency @ 25c 0 10 20 30 40 50 60 0 0.2 0.4 0.6 0.8 1 1.2 control voltage(v) ip3(dbm) ip3 @ 600mhz ip3 @ 900mhz ip3 @ 1200mhz VACC-09 + phase shift vs. frequency vs. control voltage 600-900mhz (with relation to 0v control voltage) 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 600 650 700 750 800 850 900 frequency(mhz) phase shift(deg.) 0.5v 0.6v 0.7v 0.8v 0.9v 1v VACC-09 + phase shift vs. frequency vs. control voltage 900-1200mhz (with relation to 0v control voltage) -20 -15 -10 -5 0 5 900 950 1000 1050 1100 1150 1200 frequency(mhz) phase shift(deg.) 0.5v 0.6v 0.7v 0.8v 0.9v 1v page 3 of 3 performance curves VACC-09+ performance curves notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
|
