d1u3cs-w-1300f-12-hx4ec series 81mm front end ac-dc power converter d1u3cs-w-1300f-12-hx4ec.a01 page 1 of 5 www.murata-ps.com/support www.murata-ps.com for full details go to www.murata-ps.com/rohs $ features ? ? extended power range to 1300w ? ? 1.57 " (1u) x 11.0" x 3.2" ? ? 92% ef? ciency at 50% fl ? ? 12vdc main output ? ? 3.3vsb or 5vsb output (20w) ? ? >23w/in 3 power density ? ? n+1 redundancy capable; hot plug/swap (up to 8 modules in parallel) ? ? active current sharing on 12v main output; integral mosfet oring ? ? over-voltage, over-current; over-temperature protection ? ? internal variable speed cooling fans ? ? pmbus? power management bus ? ? rohs compliant product overview the d1u3cs-w-1300f-12-hx4ec are high ef? ciency 1300w power factor corrected front end supplies with a 12v main output and a 5v or 3.3v (20w) standby. active current sharing is provided to allow up to eight (8) supplies to be operated in parallel. the supplies may be hot plugged and include integral isolation devices. the power modules are fully protected from overload and overvoltage and are able to auto-recover from overtemperature faults. status leds are provided on the front panel and additional control and status reporting is provided by hardware logic signals and via a pmbus? digital interface. a low pro? le sub 1u height enclosure provides a power density of >23w/in 3 that is ideal for delivering reliable, ef? cient power to servers, workstations, storage systems and other 12v distributed power systems. cb test certi cate and test report www.murata-ps.com / en / 3d / acdc.htm l www.murata- p s.com/en/3d/acdc.htm l www.murata-ps.com / en / 3d / acdc.htm l www.murata- p s.com/en/3d/acdc.htm l www.murata-ps.com / en / 3d / acdc.htm l available now at www.murata-ps.com/en/3d/acdc.html ordering guide model number power output main output standby output air? ow ac line & temp (108-264v; 40c) ac line & temp (90-264v; 50c) d1u3cs-w-1300f-12-ha4ec 1300w 1200w 12v 5v back to front d1u3cs-w-1300f-12-hc4ec 3.3v input characteristics parameter conditions min typ max units voltage operating range 90 115/230 264 vac input frequency 47 50/60 63 hz turn-on input voltage ramp up 81 85 89 vac turn-off input voltage ramp down 70.5 74.3 78.0 maximum current @ vin = 200vac 1300w @ 40c (max) 8 arms maximum current @ vin = 90vac 1200w @ 50c (max) 15 inrush current cold start between 0 to 200ms 25 apk power factor at 230vac; fl 0.99 ef? ciency (230vac) excluding fan load 20% fl 88 % 50% fl 92 100% fl 92 output voltage charateristics output voltage parameter conditions min typ max units 12v voltage set point accuracy 12 vdc line & load regulation 11.4 12.6 ripple & noise 1 20mhz bandwidth 150 mv p-p output current (230vac) 0 108.3 a output current (120vac) 108.3 output current (90vac) 100 load capacitance 30,000 f 3.3vsb voltage set point 3.3 vdc line & load regulation 3.2 3.4 ripple voltage & noise 1 20mhz bandwidth 100 mv p-p output current 0 6 a load capacitance 10,000 f 5vsb voltage set point 5.0 vdc line & load regulation 4.85 5.1 ripple voltage & noise 1 20mhz bandwidth 50 mv p-p output current 0 4 a load capacitance 10,000 f 1 ripple and noise are measurements are to be performed with a parallel combination of a 0.1f ceramic capacitor and 10f tantalu m capacitance on each of the power module output measurement nodes. a short coaxial cable shall be used.
d1u3cs-w-1300f-12-hx4ec series 81mm front end ac-dc power converter d1u3cs-w-1300f-12-hx4ec.a01 page 2 of 5 www.murata-ps.com/support output characteristics parameter conditions min typ max units remote sense compensation at full load (total loop for positive & negative connections) 120 mv output rise (monotonic) 10% to 95% rise time no voltage excursion startup time ac ramp up 1.5 2.5 s ps_on activation 150 ms transient response 12v, 50-100% step load 1a/s 600 mv 3.3/5vsb 50-100% step load 1a/s 165/250 current sharing accuracy (up to 8 in parallel) at 100% load 7 % hot swap transients 5% hold up time fl (full load) 12 ms environmental characteristics parameter conditions min typ max units storage temperature range non-condensing -40 70 c operating temperature range 1200w 0 50 1300w 0 40 operating humidity non-condensing 5 90 % storage humidity 595 altitude (no derating at 40c) 3000 m shock operating 30 g sinusoidal vibration operational, 2.0g; 5-500hz mtbf telcordia sr-332 m1c1 @ 40c 500 k hours safety approvals (standards) csa/ul c22.2 no.60950-1-07, amendment 1_2011 ansi/ul 60950-1-2011 iec 60950-1:2005, (2 nd edition) + a1:2009 en 60950-1:2006 + a11:2009 +a1 :2010 +a12:2011 ce marking per lvd directive 2006/95/ecs input fusing internal 16a/250v rated fast blow in ac line switching frequency 90khz for the pfc boost converter 130khz for the main output converter material flammability ul94-v0 weight 3.15/1.43 lbs/kg protection characteristics output voltage parameter conditions min. typ. max. units n/a over-temperature auto re-start 57 60 63 c 12v (main) over-voltage latching 13.3 14.5 v over-current (1300w) latching 115 125 a over-current (1200w) latching 108 118 3.3vsb over-voltage latching 3.9 4.3 v over-current auto-recovery 6.5 9.0 a 5vsb over-voltage latching 5.6 6.0 v over-current auto-recovery 5.0 6.5 a isolation characteristics parameter conditions min. typ. max. units insulation safety rating/test voltage input to output C re-enforced 3000 vrms input to chassis - basic 1500 vrms isolation output to chassis (ground) 500 vdc
d1u3cs-w-1300f-12-hx4ec series 81mm front end ac-dc power converter d1u3cs-w-1300f-12-hx4ec.a01 page 3 of 5 www.murata-ps.com/support status indicators conditions led status standby rail on; main output off; ac present & correct blinking green standby rail on; main output on solid green main output overcurrent; undervoltage, overvoltage warning blinking amber fan_fault; overtemperature; standby rail overcurrent, main output overcurrent or overvoltage red emissions and immunity characteristic standard compliance input current harmonics iec/en 61000-3-2 complies with class a limits voltage fluctuation & flicker iec/en 61000-3-3 complies conducted emissions fcc 47 cfr part 15 csipr 22/en55022 class b esd immunity iec/en 61000-4-2; level 3; criteria a radiated field immunity iec/en 61000-4-3 level 3; criteria b electrical fast transients/burst immunity iec/en 61000-4-4 level 3; criteria b surge immunity iec/en 61000-4-5 level 3; criteria a rf conducted immunity iec/en 61000-4-6 level 3; criteria a magnetic field immunity iec/en 61000-4-8 3a/m; criteria b voltage dips & interruptions iec/en 61000-4-11 230vin, 100% load, phase 0, dip 100% duration 10ms (a) 230vin, 50% load, phase 0, dip 100% duration 20ms (vsb:a, v1:a) 230vin, 100% load, phase 0, dip 100% duration > 12ms (vsb:a, v1:b) output connector & signal interface dc output and signal connector: fci# 51731-057-lf nb: b4 is the shortest last make, ? rst break sequenced signal pin blade assignment function description current (amps per pin) pb1, pb2, pb3 +12v gnd main output voltage, return 30 pb4, pb5, pb6 +12v out main output voltage 30 signal pin assignment signal name description a1 ps_on_l an input pulled up via an internal 10k ohm to the standby rail. when pulled low (via an open collector/drain drive or connection to gnd) the main output will be turned on/enabled) n/a a2 +12vrs_return main output remote sense (-ve/return) n/a a3 temp_ok ttl compatible logic high provided when the temperature is within the allowable range of operation. a4 ps_seated internally connected to gnd; when the power module is correctly seated the corresponding mating connector pin is grounded and therefore allows detection that the power module is in situ. n/a a5, b5, c5, d5 +vsb standby voltage output 2.0 a6, b6, c6, d6 +vsb gnd standby voltage output, return/gnd 2.0 b1 ac_ok incoming ac source voltage ok (present and within operational limits) n/a b2 +12vrs main 12v output remote sense line n/a b3 +12v_ishare main 12v output current share bus n/a b4 ps_inhibit/ps_kill this is the shortest last make, ? rst break (last to mate in the sequence). if left open circuit then the main output will be inhibited (no output). when inserted in to the system slot this pin must be pulled low by the system to enable (turn on) the main output and only after all other pins are connected and the power module is correctly seated. n/a c1 sda i 2 c serial data line n/a c2 scl i 2 c serial clock line n/a d1 d2 d3 d4 d5 d6 pb1 pb2 pb3 pb4 pb5 pb6 c1 c2 c3 c4 c5 c6 b1 b2 b3 b4 b5 b6 a1 a2 a3 a4 a5 a6
d1u3cs-w-1300f-12-hx4ec series 81mm front end ac-dc power converter d1u3cs-w-1300f-12-hx4ec.a01 page 4 of 5 www.murata-ps.com/support signal pin assignment signal name description current (amps per pin) c3 pwr_gd power good signal. an active ttl high signi? es when the output is within regulation limits. n/a c4 fan_fail fan fail signal (failure or locked rotor) n/a d1 a0 i 2 c lsb (least signi? cant bit) address line n/a d2 a1 i 2 c msb (most signi? cant bit) address line n/a d3 s_int system interrupt n/a d4 n/a reserved; no end user connection n/a mating connector supplier press fit, straight press fit, right angle solder straight solder right angle fci --- 51761-10002406aa --- --- wiring diagram for output current sharing notes 1. main 12vdc output: analogue active share bus. the ishare bus (pin b3) must be connected on all sharing modules. it is not re quired that the sense signals are connected to the remote load for current share to operate correctly. 2. up to eight (8) power modules can be connected in parallel (non-redundant) or n+1 con? guration. the current share bus is an alogue bi-directional (can source or sink current from the ishare bus). the voltage of the bus would measure 8vdc for a single power module at 100% load; for two (2) modules sharing a common load the ishare bus voltage would be 4v for a perfect 50/50 current share scenario. 3. vstandby output power modules can also be connected in parallel and have internal output isolation devices; however the comb ined available power is limited to that available from a single power module (3.3v or 5v; 20w) irrespective of the number of modules connected in parallel. +12v gnd +12vrs (main output remote sense) +12vrs_return +12v out b2 pb4-6 pb1-3 a2 dotted lines show optional remote sense connections. optional remote sense lines can be attached to a load that is a distance away from the power supply to improve regulation at the load. d1u3cs 12v load a1 a6,b6,c6,d6 a5,b5,c5,d5 fet, bjt, wire or switch (debounced ) to turn on +12v main output +vsb load +vsb ps_on_l +vsb gnd b4 ps_inhibit/ps_kill d1u3cs b3 +12v_ishare ps_inhibit/ps_kill b4 a6,b6,c6,d6 +vsb gnd ps_on_l a1 a5,b5,c5,d5 +vsb b3 a2 +12vrs_return +12v_ishare +12v gnd +12v out +12vrs (main output remote sense) b2 pb4-6 pb1-3
d1u3cs-w-1300f-12-hx4ec series 81mm front end ac-dc power converter d1u3cs-w-1300f-12-hx4ec.a01 page 5 of 5 www.murata-ps.com/support murata power solutions, inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. the descriptions contained her ein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. speci? cations are subject to cha nge without notice. ? 2014 murata power solutions, inc. murata power solutions, inc. 11 cabot boulevard, mans? eld, ma 02048-1151 u.s.a. iso 9001 and 14001 registered this product is subject to the following operating requirements and the life and safety critical application sales policy: refer to: http://www.murata-ps.com/requirements/ mechanical dimensions ac input connector/inlet: iec 60320-c14 dimensions: 3.20" x 11.00" x 1.57" [81.3mm x 279.4mm x 39.9mm] optional accessories description part number d1u3cs-12 output interface connector card d1u3cs-12-conc application notes document number description link ACAN-41 d1u3cs-12-conc output interface connector card www.murata-ps.com/data/apnotes/ACAN-41.pdf acan-49 d1u3cs-12 communications protocol www.murata-ps.com/data/apnotes/acan-49.pdf direction of air? ow
|
