IRMDKG6-300W 1 www.irf.com ? 2014 international rectifier september 25, 2014 dpak igbt motor drive reference design kit description the reference design power board is designed to showcase ir dpak irgr4610dpbf igbt in a motor drive application. product summary ? igbt inverter power stage for 3 phase motors ? fr4 based 1oz copper two-layer pcb ? 100 -240v ac input range ? 300w motor power range (with heatsink) ? single shunt configuration irgr4610dpbf features features benefits low v ce(on) and switching losses high efficiency in a wide range of applications and switching frequencies square rbsoa and maximum junction temperature of 175c improved reliability due to rugged hard switching performance and high power capability positive v ce(on) temperature coefficient and tight distribution of parameters excellent current sharing in parallel operation 5s short circuit soa enables short circuit protection scheme lead-free, rohs compliant environmentally friendly the 76 x 83mm board has two layers with 1oz (~ 35 m) copper each. downloaded from: http:///
IRMDKG6-300W 2 www.irf.com ? 2014 international rectifier september 25, 2014 safety precautions in addition to the precautions listed throughout this manual, please read and understand the f ollowing statements regarding hazards associated with development system. attention: the ground potential of the IRMDKG6-300W system is biased to a negative dc bus voltage potential. when measuring voltage waveform by oscilloscope, the scop e ground needs to be isolated. failure to do so may result in personal injury or death. darkened display leds is not an indication that capacitors have discharged to safe voltage levels. attention: IRMDKG6-300W system contains dc bus capacitors which take time to discharge after removal of the main supply. before working on t he drive system, wait at least three minutes and until the capacitors have discharged to safe voltage levels. failure to do so may result in personal injury or death. darkened display leds is not an indicat ion that capacitors have discharged to safe voltage levels. attention: only personnel familiar with the drive and associated machinery should plan or implement the installation, start-up, and subsequent maintenance of the system. failure to comply may result in personal injury and/or equipment damage. attention: the surface temperatures of the drive may become hot, which may cause injury. attention: IRMDKG6-300W system contains esd (electrostatic discharge) sensitive parts and assemblies. static control precautions are required when installing, testing, s ervicing or repairing this assembly. component damage may result if esd control procedures are no t followed. if you are not familiar with static control procedures, reference applicabl e esd protection handbook and guideline. downloaded from: http:///
IRMDKG6-300W 3 www.irf.com ? 2014 international rectifier september 25, 2014 attention: an incorrectly applied or installed drive can result in component damage or reduction in product life. wiring or application errors such as undersizing the moto r, supplying an incorrect or inadequate ac supply, or excessive ambient temperatures may result in system malfunction. attention: remove and lock out power from the drive before you disconnect or reconnect wires or perform service. wait three minutes after removing power to discharge the bus v oltage. do not attempt to service the drive until bus voltage has discharged to zero. failure to do s o may result in bodily injury or death. attention: do not connect power factor correction capacitors to output terminals u, v, and w. doing so may result in equipment damage or bodily injury. attention: debris when unpacking IRMDKG6-300W system is shipped with packing materials that need to be removed prior to installation. failure to remove all debris and packing materials which are un necessary for system installation may result in overheating or abnormal operating condition. downloaded from: http:///
IRMDKG6-300W 4 www.irf.com ? 2014 international rectifier september 25, 2014 hardware description a top view of the IRMDKG6-300Wboard is shown below. power supply inverter power stage j1: control connector bus capacitor j9: dc input j8: motor connector bemf sensing j7: aux supply gate driver circuit downloaded from: http:///
IRMDKG6-300W 5 www.irf.com ? 2014 international rectifier september 25, 2014 connector definition pin name comments pin name comments 1 uhin 23 pgnd 2 pgnd 24 +3.3v 3 ulin 25 n.c. 4 pgnd 26 pgnd 5 vhin 27 n.c. 6 +3.3v 28 pgnd 7 vlin 29 n.c. 8 +3.3v 30 pgnd 9 whin 31 n.c. 10 n.c. 32 n.c. 11 wlin 33 u sense connect through jumper (normally close) 12 n.c. 34 v sense connect through jumper (normally close) 13 n.c. 35 w sense connect through jumper (normally close) 14 vbus+(hv) connect through jumper (normally open) 36 +3.3v 15 pgnd 37 shunt+ 16 n.c. 38 shunt- 17 n.c. 39 n.c. 18 pgnd 40 pgnd 19 n.c. 41 n.c. 20 vbus sense 42 n.c. 21 n.c. 43 n.c. 22 n.c. 44 pgnd downloaded from: http:///
IRMDKG6-300W 6 www.irf.com ? 2014 international rectifier september 25, 2014 specifications parameters values conditions watts 300 w vin=110vac, f pwm = 10 khz, t a = 25 ? c , with heat-sink current 0.75arms maximum dc bus voltage 400v current sensing device single dc shunt power device irgr4610dpbf 15v 15v+/-5%, max 20ma used for gate drive power supply 3.3v 3.3v+/-5%, max 50ma available on j1 pcb material fr4 , copper thickness=2oz ( 70 um) dimension 70mm x 87mm system environment ambient temperature 0 to 70 ? c 95% rh max. (non-condensing) running the system 1. connect the system as in figure 1 2. power on the vdc power supply (<400vdc) 3. start the control signal generator figure 1 - connection of control signals to the dpak/d2pak board inverter output c able (not included) downloaded from: http:///
IRMDKG6-300W 7 www.irf.com ? 2014 international rectifier september 25, 2014 test condition example ? pwm: irmcf171 control board. carrier frequency:16.6khz ? load: motor test bench ? motor: gk6063-6af31-we(ke=63v/1000r/min, normal 1000rpm, io=2a) ? power board: dpak board rev 3 ? igbt: irgr4610dpbf figure 2 - example of the inverter phase current for sinusoidal motor the board can drive up to a 300w motor with the heatsink under the pcb bottom (see figure 3) downloaded from: http:///
IRMDKG6-300W 8 www.irf.com ? 2014 international rectifier september 25, 2014 figure 3 - max pcb temperature vs otuput power with heatsink revision history downloaded from: http:///
IRMDKG6-300W 9 www.irf.com ? 2014 international rectifier september 25, 2014 data and specifications are subject to change without notice ir world headquarters: 233 kansas st., el segundo, california 90245, usa tel: (310) 252-7105 tac fax: (310) 252-7903 visit us at www.irf.com for sales contact information downloaded from: http:///
|
