View TS1100-25EG5_8668445.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ts1100/01/02/03 data sheet ts1100/01/02/03 uni- and bidirectional current-sense amplifiers the ts1100/01/02/03 unidirectional and bidirectional current sense amplifiers con- sume a very low 0.68 a supply current. the ts1100 and ts1101 high-side current sense amplifiers (csa) combine a 100 v (max) input offset voltage (v os ) and a 0.6% (max) gain error (ge), with both specifica- tions optimized for any precision current measurement. the ts1102 and ts1103 csas combine a 200 v (max) v os and a 0.6% (max) ge for cost-sensitive applications. for all high-side current sensing applications, the ts1100/01/02/03 csas are self-pow- ered and feature a wide input common-mode voltage range from 2 to 27 v. for the bidirectional csas, ts1101 and ts1103, a sign comparator digital output is provided that indicates the direction of current flow. all csas are specified for operation over the C40 c to +105 c temperature range. applications ? power management systems ? portable/battery-powered systems ? smart chargers ? battery monitoring ? overcurrent and undercurrent detection ? remote sensing ? industrial control key features ? low supply current ? current sense amplifier: 0.68 a ? i vdd : 0.02 a ? high side bidirectional and unidirectional current sense amplifier ? wide csa input common mode range: +2 v to +27 v ? low csa input offset voltage: 100 v (max) (ts1100 and ts1101 only) ? low gain error: 0.6% (max) ? four gain options available: ? 25 v/v ? 50 v/v ? 100 v/v ? 200 v/v ? 5-lead and 6-lead sot23 packaging silabs.com | smart. connected. energy-friendly. rev. 1.0
1. ordering information ordering number 1 part marking description gain v/v TS1100-25EG5 tadj unidirectional current sense amplifier (v os(max) = 200 v) 25 ts1100-50eg5 tadk 50 ts1100-100eg5 tadl 100 ts1100-200eg5 tadm 200 ts1101-25eg6 tadn bidirectional current sense amplifier (v os(max) = 200 v) 25 ts1101-50eg6 tadp 50 ts1101-100eg6 tadq 100 ts1101-200eg6 tadr 200 ts1102-25eg5 tads unidirectional current sense amplifier (v os(max) = 300 v) 25 ts1102-50eg5 tadt 50 ts1102-100eg5 tadu 100 ts1102-200eg5 tadv 200 ts1101-25eg6 tadw bidirectional current sense amplifier (v os(max) = 300 v) 25 ts1101-50eg6 tadx 50 ts1101-100eg6 tady 100 ts1101-200eg6 tadz 200 note: 1. adding the suffix, "t", to the part number (e.g., ts1101-25eg6t) denotes tape and reel. ts1100/01/02/03 data sheet ordering information silabs.com | smart. connected. energy-friendly. rev. 1.0 | 1
2. system overview 2.1 typical application circuits figure 2.1. ts1100 and ts1102 typical application circuit figure 2.2. ts1101 and ts1103 typical application circuit ts1100/01/02/03 data sheet system overview silabs.com | smart. connected. energy-friendly. rev. 1.0 | 2
2.2 theory of operation the internal configuration of the ts1100/02 (a unidirectional high-side, current-sense amplifier) is based on a common operational am- plifier circuit used for measuring load currents (in one direction) in the presence of high common-mode voltages. in the general case, a current-sense amplifier monitors the voltage caused by a load current through an external sense resistor and generates an output volt- age as a function of that load current. the internal configuration of the ts1101/03 (a bidirectional high-side, current-sense amplifier) is a variation of the ts1100/02 unidirec- tional current-sense amplifier. in the design of the ts1101/03, the input amplifier was reconfigured for fully differential input/output oper- ation and a second low-threshold p-channel fet (m2) was added where the drain terminal of m2 is also connected to r out . therefore, the behavior of the ts1101/03 for when v rsC > v rs+ is identical for when v rs+ > v rsC . referring to the typical application circuit, the inputs of the op-amp based circuit are connected across an external r sense resistor that is used to measure load current. at the non-inverting input of the current-sense amplifier (the rs+ terminal), the applied voltage is i load r sense . since the rsC terminal is the non-inverting input of the internal op-amp, op-amp feedback action forces the inverting input of the internal op-amp to the same potential. therefore, the voltage drop across r sense (v sense ) and the voltage drop across r gaina (at the rs+ terminal) are equal. necessary for gain ratio matched, both r gaina and r gainb are the same value. since p-channel m1s source is connected to the inverting input of the internal op amp and since the voltage drop across r gaina is the same as the external v sense , op amp feedback action drives the gate of m1 such that m1s drain-source current is equal to: i d s ( m 1 ) = v s e n s e r g a i n a or i d s ( m 1 ) = i l o a d r s e n s e r g a i n a since m1s drain terminal is connected to r out , the output voltage of the current-sense amplifier at the out terminal is, therefore: v o u t = i l o a d r s e n se r o u t r gaina for the ts1101 and ts1103, when the voltage at the rsC terminal is greater than the voltage at the rs+ terminal, the external vsense voltage drop is impressed upon r gainb . the voltage drop across r gainb is then converted into a current by m2 that then produces an output voltage across r out . in this design, when m1 is conducting current (v rs+ > v rsC ), the ts1101/03s internal amplifi- er holds m2 off. when m2 is conducting current (v rsC > v rs+ ), the internal amplifier holds m1 off. in either case, the disabled fet does not contribute to the resultant output voltage. the current-sense amplifiers gain accuracy is therefore the ratio match of r out to r gain[a/b] . for each of the four gain options availa- ble, table 1 lists the values for r out and r gain[a/b] . the ts1101s output stage is protected against input overdrive by use of an output current-limiting circuit of 3 ma (typical) and a 7 v internal clamp protection circuit. ts1100/01/02/03 data sheet system overview silabs.com | smart. connected. energy-friendly. rev. 1.0 | 3
2.3 sign comparator output as shown in the ts1101/03s block diagram, the design of the ts1101/03 incorporated one additional feature: an analog comparator whose inputs monitor the internal amplifiers differential output voltage. while the voltage at the ts1101/03s out terminal indicates the magnitude of the load current, the ts1101/03s sign output indicates the load currents direction. the sign output is a logic high when m1 is conducting current (v rs+ > v rsC ). alternatively, the sign output is a logic low when m2 is conducting current (v rs+ < v rsC ). the sign comparators transfer characteristic is illustrated in the figure below. unlike other current-sense amplifiers that implement a out/ sign arrangement, the ts1101/03 exhibits no dead zone at i load switchover. the other attribute of the sign comparators behavior is its propagation delay as a function of applied v sense [(v rs+ C v rsC ) or (v rsC C v rs+ )]. as shown below, the sign comparators propagation delay behavior is symmetric regardless of current-flow direction and is inversely proportional to v sense . figure 2.3. sign comparator transfer characteristic and propagation delay figure 2.4. sign comparator propagation delay vs. v sense ts1100/01/02/03 data sheet system overview silabs.com | smart. connected. energy-friendly. rev. 1.0 | 4
2.4 choosing the sense resistor selecting the optimal value for the external rsense is based on the following criteria and for each commentary follows: 1. r sense voltage loss 2. v out swing vs. applied input voltage at v rs+ and desired v sense 3. total i load accuracy 4. circuit efficiency and power dissipation 5. r sense kelvin connections 2.4.1 r sense voltage loss for the lowest ir power dissipation in r sense , the smallest usable resistor value for r sense should be selected. 2.4.2 v out swing vs. applied input voltage at v rs+ and desired v sense as there is no separate power supply pin for the current-sense amplifiers, the circuit draws its power from the voltage at its rs+ and rs- terminals. therefore, the signal voltage at the out terminal is bounded by the minimum voltage applied at the rs+ terminal. therefore: v o u t ( max ) = v r s + ( min ) ? v s ense ( max ) ? v o h (max ) and r s e n s e < v o u t ( max ) g a in i l o a d ( max ) where the full-scale v sense should be less than v out(max) /gain at the applications minimum rs+ terminal voltage. for best perform- ance with a 3.6 v power supply, r sense should be chosen to generate a v sense of: a) 120 mv (for the 25 v/v gain option), b) 60 mv (for the 50 v/v gain option), c) 30 mv (for the 100 v/v gain option), or d) 15 mv (for the 200 v/v gain option) at the full-scale i load current in each application. for the case where the minimum power supply voltage is higher than 3.6 v, each of the four full-scale v sense s above can be increased. 2.4.3 total load current accuracy in the current-sense amplifiers linear region where v out < v out(max) , there are two specifications related to the circuits accuracy: a) the input offset voltage and b) gain error (ge(max) = 0.6%). an expression for the current sense amplifiers total error is given by: v o u t = g a i n ( 1 g e ) v se n s e ( g ai n v o s ) a large value for r sense permits the use of smaller load currents to be measured more accurately because the effects of offset voltag- es are less significant when compared to larger v sense voltages. due care though should be exercised as previously mentioned with large values of r sense . 2.4.4 circuit efficiency and power dissipation ir losses in r sense can be large especially at high load currents. it is important to select the smallest, usable r sense value to mini- mize power dissipation and to keep the physical size of r sense small. if the external r sense is allowed to dissipate significant power, then its inherent temperature coefficient may alter its design center value, thereby reducing load current measurement accuracy. pre- cisely because the current-sense amplifiers input stages were designed to exhibit a very low input offset voltage, small r sense values can be used to reduce power dissipation and minimize local hot spots on the pcb. ts1100/01/02/03 data sheet system overview silabs.com | smart. connected. energy-friendly. rev. 1.0 | 5
2.4.5 r sense kelvin connections for optimal v sense accuracy in the presence of large load currents, parasitic pcb track resistance should be minimized. kelvin-sense pcb connections between r sense and the current-sense amplifiers rs+ and rsC terminals are strongly recommended. the drawing below illustrates the connections between the current-sense amplifier and the current-sense resistor. the pcb layout should be bal- anced and symmetrical to minimize wiring-induced errors. in addition, the pcb layout for r sense should include good thermal manage- ment techniques for optimal r sense power dissipation. figure 2.5. making pcb connections to r sense 2.4.6 r sense composition current-shunt resistors are available in metal film, metal strip, and wire-wound constructions. wire-wound current-shunt resistors con- sist of a wire spirally wound onto a core. as a result, these types of current shunt resistors exhibit the largest self inductance. in applica- tions where the load current contains high-frequency transients, metal film or metal strip current-sense resistors are recommended. 2.4.7 internal noise filter in power management and motor control applications, current-sense amplifiers are required to measure load currents accurately in the presence of both externally-generated differential and common-mode noise. an example of differential-mode noise that can appear at the inputs of a current-sense amplifier is high-frequency ripple. high-frequency ripple (whether introduced into the circuit inductively or capacitively) can produce a differential-mode voltage drop across the external current-shunt resistor (r sense ). an example of external- ly-generated, common-mode noise is the high-frequency output ripple of a switching regulator that can result in the injection of com- mon-mode noise into both inputs of a current-sense amplifier. even though the load current signal bandwidth is dc, the input stage of any current-sense amplifier can rectify unwanted out-of-band noise that can result in an apparent error voltage at its output. this rectification of noise signals occurs because all amplifier input stages are constructed with transistors that can behave as high-frequency signal detectors in the same way pCn junction diodes were used as rf envelope detectors in early radio designs. the amplifiers internal common-mode rejection is usually sufficient to defeat injected common-mode noise. to counter the effects of externally-injected noise, it has always been good engineering practice to add external low-pass filters in ser- ies with the inputs of a current-sense amplifier. in the design of discrete current-sense amplifiers, resistors used in the external low- pass filters were incorporated into the circuits overall design to compensate for any input-bias-current-generated offset voltage and gain errors. with the advent of monolithic current-sense amplifiers, the addition of external low-pass filters in series with the current-sense amplifi- ers inputs only introduces additional offset voltage and gain errors. to minimize or altogether eliminate the need for external low-pass filters and to maintain low input offset voltage and gain errors, the current-sense amplifiers incorporate a 50 khz (typ) 2nd-order differ- ential low-pass filter as shown in the block diagrams. 2.4.8 output filter capacitor if the current-sense amplifiers are a part of a signal acquisition system in which their out terminal is connected to the input of an adc with an internal, switched-capacitor track-and-hold circuit, the internal track-and-holds sampling capacitor can cause voltage droop at v out . a good-quality 22 to 100 nf ceramic capacitor from the out terminal to gnd forms a low-pass filter with the current-sense am- plifiers r out and should be used to minimize voltage droop (holding vout constant during the sample interval. using a capacitor on the out terminal will also reduce the small-signal bandwidth as well as band-limiting amplifier noise. 2.4.9 pc board layout and power supply bypassing for optimal circuit performance, the current-sense amplifiers should be in very close proximity to the external current-sense resistor, and the pcb tracks from r sense to the rs+ and the rsC input terminals should be short and symmetric. also recommended are a ground plane and surface mount resistors and capacitors. ts1100/01/02/03 data sheet system overview silabs.com | smart. connected. energy-friendly. rev. 1.0 | 6
3. electrical characteristics table 3.1. recommended operating conditions 1 parameter symbol conditions min typ max units system specifications operating voltage range vdd 1.25 5.5 v common-mode input range v cm v rs+ , guaranteed by cmrr 2 27 v note: 1. all devices 100% production tested at t a = +25 c. limits over temperature are guaranteed by design and characterization. table 3.2. dc characteristics 1 parameter symbol conditions min typ max units system specifications no load input supply current i rs+ + i rsC 2 t a = +25 c 0.68 0.85 a 1.0 v rs+ = 25 v t a = +25 c 1.0 1.2 i vdd 0.02 0.2 current sense amplifier common mode rejection ratio cmrr 2 v < v rs+ < 27 v 120 130 db input offset voltage 3 v os ts1100 and ts1101 t a = +25 c 30 100 v C40 c < ta < +85 c 200 ts1102 and ts1103 t a = +25 c 30 200 C40 c < t a < + 85 c 300 v os hysteresis 4 v hys t a = +25 c 10 v gain g ts1100, ts1101, ts1102, ts1103 ts110x-25 25 v/v ts110x-50 50 ts110x-100 100 ts110x-200 200 gain error 5 ge t a = +25 c 0.1 0.6 % C40 c < t a < +85 c 1 % gain match 5 gm t a = +25 c 0.2 0.6 % C40 c < t a < +85 c 1 % output resistance 6 r out ts110x-25/50/100 28.0 40.0 52 k? ts110x-200 14.0 20.0 26.4 ts1100/01/02/03 data sheet electrical characteristics silabs.com | smart. connected. energy-friendly. rev. 1.0 | 7
parameter symbol conditions min typ max units out low voltage v aol ts1100 and ts1101 gain = 25 5 mv gain = 50 10 gain = 100 20 gain = 200 40 ts1102 and ts1103 gain = 25 7.5 gain = 50 15 gain = 100 30 gain = 200 60 out high voltage v aoh v oh = v rsC C v out 0.05 0.2 v sign comparator parameters (ts1106 only) output low voltage v col vdd = 1.25 v, i sink = 5 a 0.2 v vdd = 1.8 v, i sink = 35 a output high voltage v coh vdd = 1.25 v, i source = 5 a vdd C 0.2 v vdd = 1.8 v, i source = 35 a notes: 1. v rs+ = 3.6 v; v sense = (v rs+ C v rsC ) = 0 v; c out = 47 nf; v dd = 1.8 v; t a = C40 c to +105 c, unless otherwise noted. typical values are at t a = +25 c. 2. extrapolated to vout=0v. irs++irs- is the total current into the rs+ and the rsC pins. 3. input offset voltage v os is extrapolated from a v out(+) measurement with v sense set to +1 mv and a v out(C) measurement with vsense set to -1mv; vis-a-viz, average v os = (v out(C) C v out(+) )/(2 x gain). 4. amplitude of v sense lower or higher than v os required to cause the comparator to switch output states. 5. gain error is calculated by applying two values for v sense and then calculating the error of the actual slope vs. the ideal transfer characteristic. ts1100 and ts1102 only applies positive v sense values. for gain = 25, the applied v sense is 20 mv and 120 mv. for gain = 50, the applied v sense is 10 mv and 60 mv. for gain = 100, the applied v sense is 5 mv and 30 mv. for gain = 200, the applied v sense is 2.5 mv and 15 mv. 6. the device is stable for any capacitance load at v out . ts1100/01/02/03 data sheet electrical characteristics silabs.com | smart. connected. energy-friendly. rev. 1.0 | 8
table 3.3. ac characteristics 1 parameter symbol conditions min typ max units current sense amplifier output settling time t out_s 1% final value, vout = 3 v gain = 25, 50, 100 2.2 msec gain = 200 4.3 msec sign comparator parameters (ts1101 and ts1103 only) propagation delay t sign_pd v sense = 1 mv 3 msec v sense = 10 mv 0.4 msec notes: 1. v rs+ = 3.6 v; v sense = (v rs+ C v rsC ) = 0 v; c out = 47 nf; v dd = 1.8 v; t a = C40 c to +105 c, unless otherwise noted. typical values are at t a = +25 c. table 3.4. thermal conditions parameter symbol conditions min typ max units operating temperature range t op C40 +105 c table 3.5. absolute maximum limits parameter symbol conditions min typ max units rs+ voltage v rs+ C0.3 27 v rsC voltage v rsC C0.3 27 v supply voltage vdd C0.3 6 v out voltage v out C0.3 6 v sign voltage (ts1106 only) v sign C0.3 6 v rs+ to rsC voltage v rs+ C v rsC 28 v short circuit duration: out to gnd continuous continuous input current (any pin) C20 20 ma junction temperature 150 c storage temperature range C65 150 c lead temperature (soldering, 10 s) 300 c soldering temperature (reflow) 260 c esd tolerance human body model 2000 v machine model 200 v ts1100/01/02/03 data sheet electrical characteristics silabs.com | smart. connected. energy-friendly. rev. 1.0 | 9
for the following graphs, v rs+ = v rsC = 3.6 v; t a = +25 c unless otherwise noted. ts1100/01/02/03 data sheet electrical characteristics silabs.com | smart. connected. energy-friendly. rev. 1.0 | 10
ts1100/01/02/03 data sheet electrical characteristics silabs.com | smart. connected. energy-friendly. rev. 1.0 | 11
ts1100/01/02/03 data sheet electrical characteristics silabs.com | smart. connected. energy-friendly. rev. 1.0 | 12
4. pin descriptions table 4.1. pin descriptions pin part number label function 1 ts1100 ts1101 ts1102 ts1103 gnd ground. connect this pin to analog ground. 2 ts1100 ts1102 gnd ground. connect this pin to analog ground. ts1101 ts1103 sign comparator output, push-pull; sign is high for (v rs+ > v rsC ) and low for (v rsC > v rs+ ). 3 ts1100 ts1101 ts1102 ts1103 out output voltage. v out is proportional to v sense = (v rs+ C v rsC ) or (v rsC C v rs+ ). 4 ts1100 ts1101 ts1102 ts1103 rsC external sense resistor load-side connection 5 ts1100 ts1102 rs+ external sense resistor power-side connection ts1101 ts1103 vdd sign comparator external power supply pin; connect this pin to systems logic vdd supply. 6 ts1100 ts1102 n/a n/a ts1101 ts1103 rs+ external sense resistor power-side connection ts1100/01/02/03 data sheet pin descriptions silabs.com | smart. connected. energy-friendly. rev. 1.0 | 13
5. packaging 5.1 ts1100 and ts1102 package dimensions figure 5.1. ts1100 and ts1102 package diagram table 5.1. ts1100 and ts1102 package dimensions dimension min max a 1.45 a1 0.00 0.15 a2 0.90 1.30 b 0.30 0.50 c 0.09 0.20 d 2.90 bsc e 2.80 bsc e1 1.60 bsc e 0.95 bsc e1 1.90 bsc l 0.30 0.60 l2 0.25 bsc 0 8 aaa 0.15 bbb 0.20 ccc 0.10 ddd 0.20 ts1100/01/02/03 data sheet packaging silabs.com | smart. connected. energy-friendly. rev. 1.0 | 14
dimension min max note: 1. all dimensions shown are in millimeters (mm) unless otherwise noted. 2. dimensioning and tolerancing per ansi y14.5m-1994. 3. recommended card reflow profile is per the jedec/ipc j-std-020d specification for small body components. 4. this drawing conforms to the jedec solid state outline mo-178, variation aa. ts1100/01/02/03 data sheet packaging silabs.com | smart. connected. energy-friendly. rev. 1.0 | 15
5.2 ts1101 and ts1103 package dimensions figure 5.2. ts1101 and ts1103 package diagram table 5.2. ts1101 and ts1103 package dimensions dimension min max a1 0.06 0.15 a2 1.00 1.30 b 0.35 0.50 c 0.127 d 2.80 2.90 e 2.60 3.00 e1 1.50 1.70 e1 0.950 typ l 0.35 0.55 l2 0.20 bsc 1 0 3 2 10 typ note: 1. all dimensions shown are in millimeters (mm) unless otherwise noted. 2. dimensioning and tolerancing per ansi y14.5m-1994. 3. recommended card reflow profile is per the jedec/ipc j-std-020d specification for small body components. 4. this drawing conforms to the jedec solid state outline mo-178, variation aa. ts1100/01/02/03 data sheet packaging silabs.com | smart. connected. energy-friendly. rev. 1.0 | 16
6. top and bottom marking: 5 and 6-pin packages mark method: laser font size: 0.60 mm (24 mils) line 1 mark format: device identifier tadt line 5 backside: tttt = mfg code manufacturing code from the assembly pur- chase order form mark method: laser font size: 0.60 mm (24 mils) line 1 mark format: device identifier tadt line 5 backside: tttt = mfg code manufacturing code from the assembly pur- chase order form ts1100/01/02/03 data sheet top and bottom marking: 5 and 6-pin packages silabs.com | smart. connected. energy-friendly. rev. 1.0 | 17
table of contents 1. ordering information ............................1 2. system overview ..............................2 2.1 typical application circuits .........................2 2.2 theory of operation ............................3 2.3 sign comparator output ..........................4 2.4 choosing the sense resistor .........................5 2.4.1 r sense voltage loss ...........................5 2.4.2 v out swing vs. applied input voltage at v rs+ and desired v sense ...........5 2.4.3 total load current accuracy ........................5 2.4.4 circuit efficiency and power dissipation ....................5 2.4.5 r sense kelvin connections ........................6 2.4.6 r sense composition ...........................6 2.4.7 internal noise filter ...........................6 2.4.8 output filter capacitor ..........................6 2.4.9 pc board layout and power supply bypassing ..................6 3. electrical characteristics ...........................7 4. pin descriptions ............................. 13 5. packaging ............................... 14 5.1 ts1100 and ts1102 package dimensions .................... 14 5.2 ts1101 and ts1103 package dimensions .................... 16 6. top and bottom marking: 5 and 6-pin packages ................. 17 table of contents 18
disclaimer silicon laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the silicon laboratories products. characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "typical" parameters provided can and do vary in different applications. application examples described herein are for illustrative purposes only. silicon laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. silicon laboratories shall have no liability for the consequences of use of the information supplied herein. this document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. the products must not be used within any life support system without the specific written consent of silicon laboratories. a "life support system" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. silicon laboratories products are generally not intended for military applications. silicon laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. trademark information silicon laboratories inc., silicon laboratories, silicon labs, silabs and the silicon labs logo, cmems?, efm, efm32, efr, energy micro, energy micro logo and combinations thereof, "the world?s most energy friendly microcontrollers", ember?, ezlink?, ezmac?, ezradio?, ezradiopro?, dspll?, isomodem ?, precision32?, proslic?, siphy?, usbxpress? and others are trademarks or registered trademarks of silicon laboratories inc. arm, cortex, cortex-m3 and thumb are trademarks or registered trademarks of arm holdings. keil is a registered trademark of arm limited. all other products or brand names mentioned herein are trademarks of their respective holders. http://www.silabs.com silicon laboratories inc. 400 west cesar chavez austin, tx 78701 usa smart. connected. energy-friendly products www.silabs.com/products quality www.silabs.com/quality support and community community.silabs.com

▲Up To Search▲

Price & Availability of TS1100-25EG5

	To Download TS1100-25EG5 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .