View N6731B_8601974.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

k e y s i g h t n6700 modular power system family N6731B - n6786a dc power modules n6700b - n6705b mainframes specifications guide
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 2 specifications guide legal notices ? keysight technologies 2010 - 201 5 no part of this document may be photocopied, reproduced, or translated to another language without the prior agreement and written consent of keysight technologies as governed by united states and international copyright laws. warranty the materi al contained in this document is provided as is, and is subject to being changed, without notice, in future editions. further, to the maximum extent permitted by applicable law, keysight disclaims all warranties, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. keysight shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein. should keysight and the user have a separate written agreement with warranty terms covering the material in this document that conflict with these terms, the warranty terms in the separate agreement shall control. manual editions manual part number: n6700 - 90001 edition 8 , january 201 5 available in electronic format only. updates of this manual containing minor corrections may have the same edition date. revise d editions are identified by a new edition date. certification keysight technologies certifies that this product met its published specifications at time of shipment from the factory. keysight technologies further certifies that its calibration measuremen ts are traceable to the united states national institute of standards and technology, to the extent allowed by the institute's calibration facility, and to the calibration facilities of other international standards organization members. technologies licen ses the hardware and or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license. u.s. government restricted rights software and technical data rights granted to the feder al government include only those rights customarily provided to end user customers. keysight provides this customary commercial license in software and technical data pursuant to far 12.211 (technical data) and 12.212 (computer software) and, for the depa rtment of defense, dfars 252.227 - 7015 (technical data C commercial items) and dfars 227.7202 - 3 (rights in commercial computer software or computer software documentation). declaration of conformity declarations of conformity for this product and for other keysight products may be downloaded from the web. go to http://www.keysight.com/go/conform ity and click on declarations of conformity. you can then search by product number to find the latest declarati on of conformity . regulatory symbols the ce mark shows that the product complies with all applicable european directives. the c - tick mark is a registered trademark of the australian communications authority. this ism dev ice complies with canadian ices - 001. cet appareil ism est conforme la norme nmb - 001 du canada. this is the symbol for an industrial, scientific and medical, group 1 class a product. the csa mark is a registered trademark of intertek - etlsemko inc. this is the rohs ( restriction of hazardous substances) symbol for electrical and electronic equipment. this symbol indicates separate collection for electrical and electronic equipment mandated under eu law as of august 13, 2005. all electric and electronic equipment are required to be separated from n ormal waste for disposal (reference weee directive 2002/96/ec).
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 3 w here to find more information this document provides specification and supplemental characteristic information for the following instruments: ? keysight N6731B through n678 4 a power modules ? keysight n6700b through n6705b mainframes for additional technical de tails and ordering information for the keysight n6700 modular power system family, refer to the following: document description keysight n6700 modular power system family: low - profile mps mainframe for automated test environments the keysight n6700 low - p rofile modular power system (mps) is a 1u (rack unit) high, multiple - output programmable dc power supply system that enables test system integrators to optimize performance, power and price to match test needs. go to: http:// literature.cdn.keysight.com /litweb/pdf/5989 - 1411en.pdf keysight n6700 modular power system family: dc power analyzer mainframe for r&d the keysight n6705 dc power analyzer represents an entirely new instrume nt category for r&d engineers. it provides unrivaled productivity gains when sourcing and measuring dc voltage and current into a dut. using the keysight n6705 dc power analyzer, r&d engineers can gain insights into the duts power consumption in minutes, with all sourcing and measuring functions available from the front panel. go to: http:// literature.cdn.keysight.com /litweb/pdf/5989 - 6319en.pdf keysight n6700 modular power syste m family: n6780 series source/measure units the keysight n6781a /82a/85a/86a 2 - quadrant smus offer advanced sourcing and measurement capabilities required to overcome test challenges associated with optimizing power consumption and maximizing battery life o f battery - powered devices and their components. the keysight n6784a 4 - quadrant smu offers advanced sourcing and measurement capabilities in four quadrants for general purpose applications. go to: http:// literature.cdn.keysight.com /litweb/pdf/5990 - 5829en.pdf keysight n6700 modular power system family: battery charge/discharge module the keysight n6783a - bat battery charge/discharge module is a basic, 2 - quadrant dc power module desi gned to be used by mobile device designers. its 2 - quadrant operation allows it to act as a programmable power supply to charge the battery or as a programmable electronic load to discharge the battery, all in one instrument. go to: http:// literature.cdn.keysight.com /litweb/pdf/5990 - 8662en.pdf keysight n6700 modular power system family: mobile communications dc power module the keysight n6783a - mfg mobile communications dc power mo dule offers advanced features specifically for testing battery - powered (mobile) devices in manufacturing or automated test environments. go to: http:// literature.cdn.keysight.com / litweb/pdf/5990 - 8643en.pdf note you can contact keysight technologies at one of the following telephone numbers for warranty, service, or technical support information. in the united states: (800) 829 - 4444 in europe: 31 20 547 2111 in japan: 0120 - 421- 345 or use our web link for information on contacting keysight in your country or specific location: www. keysight .com/find/assist or contact your keysight technologies representative. the web contains the mo st up to date version of this manual. go to http:// literature.cdn.keysight.com /litweb/pdf/n6700 - 90001.pdf .
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 4 specifications guide contents 1 - power module differences ................................ ................................ ................. 5 power mod ule differences C for keysight n6700 modular power system ....................................................................................................... 6 power module differences C for keysight n6705 dc power analyzer ..................................................................................................... 8 power module option characteristics ............................................... 10 2 - keysight n673xb, n674xb, n677xa dc power modules ................................ . 11 performance specifications ................................................................. 12 supplemental characteristics ............................................................. 14 output quadrant characteristic .......................................................... 17 arbitr ary waveform generator maximum bandwidth ..................... 17 3 - keysight n675xa high performance power modules ................................ ....... 19 performance specifications ................................................................. 20 supplemental characteristics ............................................................. 21 autoranging characteristic .................................................................. 23 ou tput impedance graphs ................................................................... 23 arbitrary waveform generator maximum bandwidth ..................... 26 4 - keysight n676xa precision power modules ................................ ..................... 27 performance specifications ................................................................. 28 supplemental characteristics ............................................................. 29 autorang ing characteristic .................................................................. 31 output impedance graphs ................................................................... 31 arbitrary waveform generator maximum bandwidth ..................... 33 5 - keysight n678xa source/measure units ................................ .......................... 35 performance specifications ................................................................. 36 supplemental charac teristics ............................................................. 38 output quadrant characteristic .......................................................... 43 output impedance graphs ................................................................... 44 voltage programming response ........................................................ 46 measurement accuracy and resolution ............................................ 48 6 - keysight n6783a - bat, n6783a - mfg application - specific power modules ... 49 performance specifications ................................................................. 50 supplemental characteristics ............................................................. 51 output quadrant characteristic .......................................................... 52 7 - keysight n6700 modular power system mainframes ................................ ....... 53 supplemental ch aracteristics ............................................................. 54 outline diagrams ................................................................................... 56
5 chapter 1 power module differences power module differences C for keysight n6700 modular po wer system ....................................................................................................... 6 power module differences C for keysight n6705 dc power analyzer ..................................................................................................... 8 power module option characteristics ............................................... 10 this chapter provides a brief overview of the basic differences between the keysight n 6700 series dc power modules. note that the basic capabilities of a power module depend not only on its hardware capabilities, but also the on the ha rdware and firmware capabilities of the mainframe in which it is installed. in addition to the ir primary output and measurement capabilities , power m odules installed in a keysight n6705 dc power analyzer have expanded capabilities such as front panel scop e view, arb itrary waveform generation, and internal and external data logging . refer to the keysight n6700 or n6705 users guide for more information about the power module capabilities.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 6 specifications guide power module differences C for keysight n6700 modular power systems ke ysight N6731B C n6777a differences feature dc power high - performance precision ( = available) n673xb, n674xb, n677xa n675xa n676xa 50 w output rating N6731B C n6736b n6751a n6761a 100 w output rating n6741b C n6746b n6752a n6762a 300 w output rating n6 773a C n6777a n6753a, n6754a n6763a, n6764a 500 w output rating n6755a, n6756a n6765a, n6766a output disconnect relays option 761 option 761 option 761 output disconnect/polarity reversal relays note 1 option 760 option 760 option 760 autoranging outp ut capability voltage or current turn - on priority n6761a, n6762a precision voltage and current measurements low voltage and low current output range n6761a, n6762a low voltage and low current measurement range 200 microampere measurement range note 2 option 2ua simultaneous voltage and current measurement s scpi command output list capability note 3 option 054 option 054 scpi command array readback note 3 option 054 option 054 scpi command programmable sample rate note 3 option 054 optio n 054 scpi command external data logging note 3 option 054 option 054 double - wide (occupies 2 channel locations) n6753a C n6756a n6763a C n6766a 1 o ption 760 limits the output current to 10a max imum on models n6742b and n6773a. option 760 is not available on models n6741b, n6751a , n675 2 a, n6761a , and n676 2 a . 2 option 2ua.is only available on models n6761a and n6762a. it includes option 761. 3 only available when using the remote interfaces; not from the front panel.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 7 keysight n6781a C n6786 a differe nces feature source/measure units (smu) application - specific ( = available) n6781a n6782a n6784a n 6 785a n 6 786a n6783a bat n6783a mfg output rating 20 w 20 w 20 w 80 w 80 w 24 w 18 w 2 - quadrant operation 4 - quadrant operation auxiliary voltage measurement input output disconnect rela ys option 761 option 761 negative voltage protection voltage or current priority mode programmable output resistance multiple voltage output ranges 3 3 3 4 4 multiple current output ranges 3 3 4 4 4 mu ltiple voltage measurement ranges 3 3 3 multiple current measurement ranges 4 4 4 3 3 2 2 simultaneous voltage and current measurements seamless measurement autoranging scpi command output list capability note 1, 2 scpi command array readback note 2 scpi command programmable sample rate note 2 scpi command external data logging note 2 double - wide (occupies 2 channel locations) 1 l ist capability is not availa ble on the negative current output on model n6783a. 2 only available when using the remote interfaces; not the front panel.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 8 specifications guide power module differences C for keysight n6705 dc power analyzers keysight n673 1 b C n677 7 a differences feature dc power high - performance precision ( = available) n673xb, n674xb, n677xa n675xa n676xa 50 w output rating N6731B C n6736b n6751a n6761a 100 w output rating n6741b C n6746b n6752a n6762a 300 w output rating n6773a C n6777a n6753a, n6754a n6763a, n6764a 500 w output rating n6755a, n6756a n6765a, n6766a output disconnect relays option 761 option 761 option 761 output disconnect/polarity reversal relays note 1 option 760 option 760 option 760 arbitrary waveform generation autoranging output capability voltage or current turn - on priority n6761a, n6762a precision voltage and current measurements low voltage and low current output range n6761a, n6762a low voltage and low current measurement range 200 microampere measurement range note 2 option 2ua voltage or c urrent scope traces simultaneous voltage and current scope traces simultaneous voltage and current data logging note 3 interleaved voltage and current data logging note 3 dynamic current correction n6751a, n6752a n6761a, n6762a sc pi command output list capability note 4 scpi command array readback note 4 scpi command programmable sample rate note 4 scpi command external data logging note 4 double - wide (occupies 2 channel locations) n6753a C n6756a n6763 a C n6766a 1 option 760 limits the output current to 10a maximum on models n6742b and n6773a . option 760 is not available on models n6741b, n6751a, n6752a, n6761a, and n6762a. 2 option 2ua is only available on models n6761a and n6762a. it includes optio n 761 . 3 option 055 deletes the data logger function on model n6705. 4 only available when using the remote interfaces; not from the front panel.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 9 keysight n678 1 a C n678 6 a differences feature source/measure units (smu) application - specific ( = available) n6781a n6782a n6784a n 6 785a n6 786a n6783a bat n6783a mfg output rating 20 w 20 w 20 w 80 w 80 w 24 w 18 w 2 - quadrant operation 4 - quadrant operation auxiliary voltage measurement input output disconnect rela ys option 761 option 761 arbitrary waveform generation note 1 negative voltage protection voltage or current priority mode cc load/cv load voltage/current measurement only batt ery emulator/charger programmable output resistance multiple voltage output ranges 3 3 3 4 4 multiple current output ranges 3 3 4 4 4 multiple voltage measurement ranges 3 3 3 multiple current measurement ranges 4 4 4 3 3 2 2 voltage or current scope traces simultaneous voltage and current measurements simultaneous voltage and current data logging note 2 interleaved voltage and current data logging note 2 seamless measurement autoranging scpi command output list capability note 1, 3 scpi command array readback note 3 scpi command programmable sample rate note 3 scpi command external data logging note 3 scp i command histogram measurements note 3 double - wide (occupies 2 channel locations) 1 arbitrary waveform generation and l ist capa bility are not available on the negative current output on model n6783a. 2 option 055 deletes the data log ger function on model n6705. 3 only available when using the remote interfaces; not the front panel.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 10 specifications guide power module option characteristics option 760 & 761 option 76 1 provides output and sense disconnect relays. option 76 0 provides polarity reversal in addit ion to output and sense disconnect. note that models n678xa smu have output and sense disconnect relays built in. ? option 760 limits the output current to 10 a on models n6742b and n6773a. ? option 760 is not available on models n6741b, n6751a, n6752a , n6761a, n6762a, and n6781a C n678 6 a although the plus and minus rail of the output power mesh are physically disconnected from the output terminals with options 760 and 761, a small ac network is still connected across the plus and minus output terminals (see figure) . option 054 option 054 (high - speed test extensions) include output list and digitized measurement capability. this option is separately orderable for models n673xb, n674xb, n677xa, and n675xa when installed in an n6700 mps mainframes. all oth er power modules as well as the n67 05 dc power analyzer mainframes have output list and digitized measurement capability built in. o utput list : ? maximum number of steps = 512 ? maximum dwell time in seconds = 262 ? maximum list repetitions = 2 56 or inf inite digitized measurement: ? maximum measurement points = 524 ,288 ? maximum sample rate = 97.656 khz option 2ua option 2ua is a 200 microampere measurement range available on models n6761a and n6762a only. it includes option 761 relay capability. + s + -s option 761 + rail + sense - rail - sense
11 chap ter 2 keysight n673xb , n674xb , n677xa dc power modules performance specifications ................................................................. 12 supplemental characteristics ............................................................. 14 output quadrant characteristic .......................................................... 17 arbitrary waveform generator maximum bandwidth ..................... 17 unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40 c after a 30 - minute warm - up period. specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). refer to the keysight n6700 or n6705 service guide for the setup conditions for all performance specifications. supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. all supplemental characteristics are typica l unless otherwise noted.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 12 specifications guide performance specifications (N6731B - n6746b) N6731B/ n6741b n6732b/ n6742b n6733b/ n6743b n6734b/ n6744b n6735b/ n6745b n6736b/ n6746b dc output ratings: voltage 0 - 5 v 0 - 8 v 0 - 20 v 0 - 35 v 0 - 60 v 0 - 100 v current note 1 0 - 10 a/ 0 - 20 a 0 - 6.25 a/ 0 - 12.5 a note 2 0 - 2.5 a / 0 - 5 a 0 - 1.5 a / 0 - 3 a 0 - 0.8 a / 0 - 1.6 a 0 - 0.5 a / 0 - 1 a power 50 w / 100 w 50 w / 100 w 50 w / 100 w 52.5w / 105w 50 w / 100 w 50 w / 100 w output ripple and noise (pa rd): (from 20 hz C 20 mhz) cv peak - to - peak 10 mv / 20 mv 12 mv 14 mv 15 mv 25 mv 30 mv cv rms 2 mv 2 mv 3 mv 5 mv 9 mv 18 mv load effect (regulation): (applies for any output load change, with a maximum load - lead drop of 1v/lead. the load lead drop reduces the maximum available voltage at the load. ) voltage 5 mv 6 mv 9 mv 11 mv 13 mv / 16 mv 20 mv / 30 mv current 2 ma 2 ma 2 ma 2 ma 2 ma 2 ma source effect (regulation): voltage 1 mv 2 mv 2 mv 4 mv 6 mv 10 mv current 1 ma 1 ma 1 ma 1 ma 1 ma 1 ma programming accuracy: (@ 23 c 5 c after a 30 minute warm - up. applies from minimum to maximum programming range at any load.) voltage 0.1% + 19 mv 0.1% + 19 mv 0.1% + 20 mv 0.1% + 35 mv 0.1% + 60 mv 0.1% +100 mv current 0.15% + 20 ma 0.15% + 20 ma 0.15% + 20 ma 0.15% + 20 ma 0.15% + 20 ma 0.15% + 10ma voltmeter/ammeter measurement accuracy: ( @ 23 c 5 c . applies when measuring the default value of 1024 data points with a 20.48 v time interval . ) voltage 0.1% + 20 mv 0.1% + 20 mv 0.1% + 20 mv 0.1% + 35 mv 0.1% + 60 mv 0.1% +100 mv current 0.15% + 20 ma 0.15% + 10 ma 0.15% + 5 ma 0.15% + 4 ma 0.15% + 4 ma 0.15% + 2 ma load transient recovery time: ( t ime to recover to within th e settling band following a load change from 50% to 100% and from 100% to 50% of full load.) voltage settling band note 3 0.08 v / 0.1 v note 3 0.08 v / 0.1 v 0.2 v / 0.3 v 0.2 v / 0.3 v 0.4 v / 0.5 v 0.5 v / 1.0 v time < 200 s < 200 s < 200 s < 200 s < 200 s < 200 s
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 13 performance specifications (n6773a - n6777a) n6773a n6774a n6775a n6776a n6777a dc output ratings: voltage 0 - 20 v 0 - 35 v 0 - 60 v 0 - 100 v 0 - 150 v current note 1 0 - 15 a note 2 0 - 8.5 a 0 - 5 a 0 - 3 a 0 - 2 a power 300 w 300 w 300 w 300 w 300 w output ripple and noise (pard): (from 20 hz C 20 mhz) cv peak - to - peak 20 mv 22 mv 35 mv 45 mv 68 mv cv rms 3 mv 5 mv 9 mv 18 mv 27 mv load effect (regulation) : (applies for any output load change, with a maximum load - lead drop of 1v/lead. the load lead drop reduces the maximum available voltage at the load.) voltage 13 mv 16 mv 24 mv 45 mv 68 mv current 6 ma 6 ma 6 ma 6 ma 6 ma source effect (regulation) : voltage 2 mv 4 mv 6 mv 10 mv 15 mv current 1 ma 1 ma 1 ma 1 ma 1 ma programming accuracy: (@ 23 c 5 c after 30 minute warm - up. applies from minimum to maximum programming range at any load.) voltage 0.1% + 20 mv 0.1% + 35 mv 0.1% + 60 mv 0.1 % +100 mv 0.1% +150 mv current 0.15% + 60 ma 0.15% + 60 ma 0.15% + 60 ma 0.15% + 30 ma 0.15% + 30 ma voltmeter/ammeter measurement accuracy: (@ 23 c 5 c. applies when measuring the default value of 1024 data points with a 20.48 v time interval .) voltage 0.1% + 20 mv 0.1% + 35 mv 0.1% + 60 mv 0.1% +100 mv 0.1% +150 mv current 0.15% + 15 ma 0.15% + 12 ma 0.15% + 12 ma 0.15% + 6 ma 0.15% + 6 ma load transient recovery time: ( t ime to recover to within the settling band followi ng a load change from 50% to 100% and from 100% to 50% of full load.) voltage settling band 0.3 v note 4 0.3 v note 4 0.5 v 1.0 v 2.0 v time < 250 s < 250 s < 250 s < 250 s < 250 s 1 output current is derated 1% per c above 40c. 2 w hen relay o ption 760 is installed on model s n6742b and n6773a, the output current is limited to 10 a. 3 when relay option 760 or 761 is installed, the settling band is 0.10v/0.125 v. option 760 is not available on model n6741b. 4 when relay o ption 760 or 761 is installed, the settling band is 0.35 v.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 14 specifications guide supplemental characteristics (N6731B - n6746b) N6731B/ n6741b n6732b/ n6742b n6733b/ n6743b n6734b/ n6744b n6735b/ n6745b n6736b/ n6746b programming ranges: voltage 15 mv C 5 .1 v 15 mv C 8 .16 v 30 mv C 20.4 v 40 mv C 35.7 v 70 mv C 61.2 v 100 mv C 102 v current 60 ma C 10.2a/ 60 ma C 20.4 a 40 ma C 6.375 a/ 40 ma C 12.75 a 10 ma C 2.55 a/ 10 ma C 5.1 a 5 ma C 1.53 a/ 5 ma C 3.06 a 2.5 ma C 0.85 a/ 2.5 m a C 1.7 a 1.5 ma C 0.51a/ 1.5 ma C 1.02 a programm ing resolution: voltage 3.5 mv 4 mv 7 mv 10 mv 18 mv 28 mv current 7 ma 4 ma 3 ma 2 ma 1 ma 0.5 ma measurement resolution: voltage 3 mv 4 mv 10 mv 18 mv 30 mv 50 mv current 10 ma 7 ma 3 ma 2 ma 1 ma 0.5 ma programming temperature coefficient per c: voltage 0.005% +0.1mv 0.005% + 0.1 mv 0.005% + 0.2 mv 0.005% + 0.5 mv 0.005% + 0.5 mv 0.005% + 1 mv current 0.005% + 1 ma 0.005% + 0.5 ma 0.005% + 0.1 ma 0.005% +0.05ma 0.005% +0.02ma 0.005% +0.02ma measurement temperature coefficient per c: voltage 0 .01% + 0.1mv 0.01% + 0.1 mv 0.01% + 0.2 mv 0.01% + 0.2 mv 0.01% + 0.5 mv 0.01% + 0.5 mv current 0.01% + 1 ma 0.01% + 0.5 ma 0.01% + 0.1 ma 0.01% + 0.05 ma 0.01% + 0.02 ma 0.01% + 0.02 ma measurement small signal bandwidth: ( C 3 db typical) voltage 25 kh z 25 khz 25 khz 25 khz 25 khz 25 khz correction on note 1 10 khz 10 khz 10 khz 10 khz 10 khz 10 khz current note 2 25 khz 25 khz 25 khz 25 khz 25 khz 25 khz correction on note 1 2 khz 2 khz 2 khz 2 khz 2 khz 2 khz n6705 mainframe oscilloscope mea surement accuracy: (@t 23 c 5 c; accuracy of any individual point in the trace) voltage 0.1% + 25 mv 0.1% + 30 mv 0.1% + 45 mv 0.1% + 75 mv 0.1% + 130 mv 0.1% + 190 mv current 0.15% + 70ma 0.15% + 40 ma 0.15% + 20 ma 0.15% + 14 ma 0.15% + 12 ma 0.15% + 7 ma correction on note 1 0.15% + 50 ma 0.15% + 30 ma 0.15% + 15 ma 0.15% + 10 ma 0.15% + 9 ma 0.15% + 5 ma up - programming and down - programming time with full resistive load: (time from 10% to 90% of total voltage excursion; for voltage setting from 0v to full scale and full scale to 0v) 20 ms 20 ms 20 ms 20 ms 20 ms 20 ms up - programming and down - programming settling time with full resistive load: (time from start of voltage change to 0.1% of full - scale value; for voltage setting from 0v to full s cale and full scale to 0v) 100 ms 100 ms 100 ms 100 ms 100 ms 100 ms over - voltage protection: accuracy 0.25% + 50mv 0.25% + 50 mv 0.25% + 75 mv 0.25% + 100 mv 0.25% + 200 mv 0.25% + 250 mv with option. 760 0.25%+600mv 0.25% + 600 mv 0.25% + 350 mv 0 .25% + 250 mv 0.25% + 300 mv 0.25% + 300 mv with option. 761 0.25%+600mv 0.25% + 600 mv 0.25% + 350 mv 0.25% + 250 mv 0.25% + 300 mv 0.25% + 300 mv maximum setting 7.5 v 10 v 22 v 38.5 v 66 v 110 v response time 50 s from occurrence of over - voltage c ondition to start of output shutdown
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 15 supplemental characteristics (continued) N6731B/ n6741b n6732b/ n6742b n6733b/ n6743b n6734b/ n6744b n6735b/ n6745b n6736b/ n6746b output ripple and noise (pard): cc rms 8 ma 4 ma 2 ma 2 ma 2 ma 2 ma common mode n oise: (from 20 hz C 20 mhz; from either output to chassis) rms 1 ma 1 ma 1 ma 1 ma 1 ma 1 ma peak - to - peak < 15 ma < 10 ma < 10 ma < 10 ma < 10 ma < 10 ma remote sense capability: outputs can maintain specifications with up to a 1 - volt drop per load le ad. the load lead drop reduces the maximum available voltage at the load. series and parallel operation: identically rated outputs can be operated directly in parallel or can be connected for straight series operation. minimum output turn - on delay: ( time from when any output on command is received until the output starts turning on) without relay 32 ms 32 ms 32 ms 32 ms 32 ms 32 ms with option 760 58 ms 58 ms 58 ms 58 ms 58 ms 58 ms 1 correction on compensates for current flowing into the output c apacitor during voltage transients. 2 stated values apply when the load resistance is at or close to zero. to determine the frequency for larger resistance values s, refer to the users guide under measurement system bandwidth. supplemental characteri stics (n6773a - n6777a) n6773a n6774a n6775a n6776a n6777a programming ranges: voltage 30 mv C 20.4 v 40 mv C 35.7 v 70 mv C 61.2 v 100 mv C 102 v 145 mv C 153 v current 30 ma C 15.3 a 15 ma C 8.67 a 7.5 ma C 5.1 a 4.5 ma C 3.06 a 2.75ma C 2.04 a programm ing resolution: voltage 7 mv 10 mv 18 mv 28 mv 43 mv current 9 ma 6 ma 3 ma 1.5 ma 1 ma measurement resolution: voltage 10 mv 18 mv 30 mv 50 mv 77 mv current 9 ma 6 ma 3 ma 1.5 ma 1 ma programming temperature coefficient per c: voltage 0.01% + 0.2 mv 0.01% + 0.5 mv 0.01% + 0.5 mv 0.01% + 1 mv 0.01% + 1 mv current 0.01% + 0.5 ma 0.01% + 0.5 ma 0.01% + 0.1 ma 0.01% + 0.1 ma 0.01% + 0.1 ma measurement temperature coefficient per c: voltage 0.01% + 0.2 mv 0.01% + 0.2 mv 0.01% + 0.5 mv 0.01% + 0.5 mv 0.01% + 0.5 mv current 0.01% + 0.5 ma 0.01% + 0.5 ma 0.01% + 0.05 ma 0.01% + 0.05 ma 0.01% + 0.05 ma measurement small signal bandwidth: ( C 3 db typical) voltage 25 khz 25 khz 25 khz 25 khz 25 khz 25 khz correction on note 1 10 khz 10 khz 1 0 khz 10 khz 10 khz 10 khz current note 2 25 khz 25 khz 25 khz 25 khz 25 khz 25 khz correction on note 1 2 khz 2 khz 2 khz 2 khz 2 khz 2 khz
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 16 specifications guide supplemental characteristics (continued) n6773a n6774a n6775a n6776a n6777a n6705 mainframe oscilloscope measurement accuracy: (@ 23 c 5 c; accuracy of any individual point in the trace) voltage 0.1% + 45 mv 0.1% + 75 mv 0.1% + 120 mv 0.1% + 160 mv 0.1% + 175 mv current 0.15% + 45 ma 0.15% + 27 ma 0.15% + 22 ma 0.15% + 12 ma 0.15% + 12 ma correcti on on note 1 0.15% + 35 ma 0.15% + 22 ma 0.15% + 19 ma 0.15% + 9 ma 0.15% + 9 ma up - programming and down - programming time with full resistive load: (time from 10% to 90% of total voltage excursion; for voltage setting from 0v to full scale and full scale to 0v) 20 ms 20 ms 20 ms 20 ms 20 ms maximum up - programming and down - programming settling time with full resistive load: (time from start of voltage change to 0.1% of full - scale value; for voltage setting from 0v to full scale and full scale to 0v) 100 ms 100 ms 100 ms 100 ms 100 ms over - voltage protection: accuracy 0.25% +100 mv 0.25% + 130 mv 0.25% + 260 mv 0.25% + 650 mv 0.25% + 650 mv with option. 761 0.25% + 500 mv 0.25% + 350 mv 0.25% + 350 mv 0.25% + 650 mv 0.25% + 650 mv with op tion. 760 0.25% + 700 mv 0.25% + 700 mv 0.25% + 400 mv 0.25% + 650 mv 0.25% + 650 mv maximum setting 22 v 38.5 v 66 v 110 v 165 v response time 50 s from occurrence of over - voltage condition to start of output shutdown output ripple and noise (pard): cc rms 6 ma 6 ma 6 ma 6 ma 6 ma common mode noise: (from 20 hz C 20 mhz; from either output to chassis) rms 2 ma 2 ma 2 ma 2 ma 2 ma peak - to - peak < 20 ma < 20 ma < 20 ma < 20 ma < 20 ma remote sense capability: outputs can maintain specificatio ns with up to a 1 - volt drop per load lead. the load lead drop reduces the maximum available voltage at the load. series and parallel operation: identically rated outputs can be operated directly in parallel or can be connected for straight series operat ion. minimum output turn - on delay: (time from when any output on command is received until the output starts turning on) without relay 32 ms 32 ms 32 ms 32 ms 32 ms with option 760 58 ms 58 ms 58 ms 58 ms 58 ms 1 correction on compensates for curre nt flowing into the output capacitor during voltage transients. 2 stated values apply when the load resistance is at or close to zero. to determine the frequency for larger resistance values s, refer to the users guide under measurement system bandwidth .
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 17 output quadrant characteristic arbitrary waveform generator maximum bandwidth note the information in this section only applies when the p ower modules are installed in a keysight n6705 dc power analyzer. the following tables characterize the maximum bandwidth of the arbitrary waveform generator. the maximum bandwidth is based on a sine wave into a resistive load and apples to any output current. the following definitions apply in the frequency tables: v p - p = voltage peak - to - peak 3 db max. = max. fre quency where the voltage drops to 3 db below its setting 6 db max. = max. frequency where the voltage drops to 6 db below its setting thd 3 db = the total harmonic distortion at 3 db max. frequency thd 6 db = the total harmonic distortion at 6 db max. f requency voltage 3 db max thd 3 db 6 db max thd 6 db N6731B & n6741b 0.1 vp - p 175 hz 1.0% 260 hz 3.0% 0.1 vp - p 125 hz 1.0% 175 hz 3.0% 0.3 vp - p 75 hz 6.0% 100 hz 6.0% 0.5 vp - p 40 hz 9.0% 55 hz 9.0% 5.0 vp - p 20 hz 10% 37 hz 10% n6732b & n6742b 0 .1 vp - p 125 hz 1.0% 200 hz 3.0% 0.2 vp - p 125 hz 1.0% 180 hz 3.0% 0.4 vp - p 75 hz 6.0% 100 hz 6.0% 0.8 vp - p 40 hz 8.5% 60 hz 8.5% 8.0 vp - p 20 hz 10% 37 hz 10% current + rated current 0 voltage + rated voltage maximum power
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 18 specifications guide arbitrary waveform generator maximum bandwidth (continued) voltage 3 db max thd 3 db 6 db max thd 6 db 3 db max thd 3 db 6 db max thd 6 db n6733b & n6743b n6773a 0.2 vp - p 110 hz 1.0% 190 hz 3.0% 125 hz 1.5% 210 hz 4.0% 0.4 vp - p 110 hz 1.0% 160 hz 3.0% 125 hz 1.5% 180 hz 4.0% 1.0 vp - p 72 hz 6.0% 95 hz 6.0% 75 hz 6.0% 95 hz 6.0% 2.0 vp - p 40 hz 8.0% 55 hz 8.5% 42 hz 9.0% 60 hz 9.0% 20 vp - p 20 hz 10% 37 hz 10% 20 hz 10% 37 hz 10% n6734b & n6744b n6774a 0.4 vp - p 125 hz 1.0% 200 hz 1.0% 125 hz 1.0% 200 hz 1.0% 0.7 vp - p 125 hz 1.0% 175 hz 3.5% 125 hz 1.0% 160 hz 3.0% 1.8 vp - p 72 hz 6.0% 100 hz 6.0% 75 hz 6.0% 95 hz 6.0% 3.5 vp - p 40 hz 8.0% 55 hz 8.5% 40 hz 8.5% 55 hz 8.5% 35 vp - p 20 hz 8.0% 37 hz 8.5% 20 hz 10% 37 hz 10% n6735b & n6745b n6775a 0.6 vp - p 100 hz 1.0% 180 hz 1.0% 120 hz 1.0% 200 hz 1.0% 1.2 vp - p 100 hz 1.0% 160 hz 3.0% 120 hz 1.0% 160 hz 3.0% 3.0 vp - p 70 hz 5.5% 92 hz 5.5% 70 hz 5.0% 95 hz 6.0% 6.0 vp - p 40 hz 8.0% 55 hz 8.0% 40 hz 8.5% 55 hz 8.5% 60 vp - p 20 hz 8.0% 37 hz 8.0% 20 hz 10% 35 hz 10% n6736b & n6746b n6776a 1.0 vp - p 90 hz 1.0% 160 hz 1.5% 75 hz 1.0% 160 hz 1.0% 2.0 vp - p 90 hz 1.0% 150 hz 3.0% 75 hz 1.0% 150 hz 3.0% 5.0 vp - p 62 hz 4.5% 85 hz 6.0% 55 hz 4.0% 75 hz 6.0% 10 vp - p 37 hz 8.0% 50 hz 8.0% 35 hz 8.0% 45 hz 8.0% 100 vp - p 20 hz 8.0% 35 hz 8.0% n/a n/a 35 hz 8.0% n6777a 1.5 vp - p 70 hz 1.0% 150 hz 1.0% 3.0 vp - p 55 hz 5.0% 120 hz 2.0% 7.5 vp - p 55 hz 5.0% 70 hz 6.0% 15 vp - p 35 hz 7.0% 55 hz 7.0% 150 vp - p n/a n/a 30 hz 1.0%
19 chapter 3 keysight n675xa high performance power modules performance spec ifications ................................................................. 20 supplemental characteristics ............................................................. 21 autoranging characteristic .................................................................. 23 output impedance graphs ................................................................... 23 arbitrary waveform generator maximum bandwidth ..................... 26 unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40 c after a 30 - minute warm - up period. specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). refer to the keysight n6700 or n6705 service gui de for the setup conditions for all performance specifications. supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. all supplemental characteristics are typical unless otherwise noted.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 20 specifications guide performance specifications n6751a/n6752a n6753a/n6755a n6754a/n6756a dc output ratings: voltage 0 - 50 v 0 - 20 v 0 - 60 v current note 1 0 - 5 a / 0 - 10 a 0 - 50 a 0 - 20 a / 0 - 17a power 50 w / 100 w 300 w / 500 w 300 w / 500 w output ri pple and noise (pard): (from 20 hz C 20 mhz) cv peak - to - peak 4.5 mv 5 mv 6 mv cv rms 0.35 mv 1 mv 1 mv load effect (regulation): (applies for any output load change, with a maximum load - lead drop of 1v/lead. the load lead drop reduces the maximum ava ilable voltage at the load. ) voltage 2 mv 2 mv 2 mv current 2 ma 12 ma 5 ma source effect (regulation): voltage 1 mv 0.5 mv 1.2 mv current 1 ma 5 ma 2 ma programming accuracy: (@ 23 c 5 c after 30 min ute warm - up. applies from min imum to max imum p rogramming range at any load. ) voltage 0.06% + 19 mv 0.06% + 10 mv 0.06% + 25 mv current 0.1% + 20 ma 0.1% + 30 ma 0.1% + 12 ma voltmeter/ammeter measurement accuracy: (@ 23 c 5 c. applies when measuring the default value of 1024 data points with a 20.48 v time interval .) voltage 0.05% + 20 mv 0.05% + 10 mv 0.05% + 25 mv current 0.1% + 4 ma 0.1% + 30 ma 0.1% + 8 ma load transient recovery time: ( t ime to recover to within the settling band following a load change - from 60% to 100% and from 100% to 60 % of full load for model n6751a - from 50% to 100% and from 100% to 50% of full load for models n6752a through n6756a.) voltage settling band 75 mv note 2 30 mv note 3 90 mv note 4 time < 100 s < 100 s < 100 s 1 output current is derated 1% p er c above 40c. 2 when relay option 761 is installed on model n6752a , the settling band is 125 mv . 3 when relay option 760 or 761 is installed on model n6753a and n6755a, the settling band is 200 mv. 4 when relay option 760 or 761 is installed on model n6754a and n6756a, the settling band is 350 mv.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 21 supplemental characteristics n6751a / n6752a n6753a / n6755a n6754a / n6756a programming ranges: voltage 20 mv C 51 v 10 mv C 20.4 v 25 mv - 61.2 v current 10 ma C 5.1a/10 ma C 10.2a 50 ma C 51 a 20 ma C 20.4 a/20 ma C 17.3a programming resolution: voltage 3.5 mv 1.5 mv 4.2 mv current 3.25 ma 16.3 ma 6.5 ma measurement resolution: voltage 1.8 mv 0.8 mv 2.2 mv current 410 a 2.05 ma 0.82 ma programming temperature coefficient per c: voltage 18 ppm + 160 v 35 ppm + 100 v 35 ppm + 170 v current 100 ppm + 45 a 60 ppm + 500 a 60 ppm + 200 a measurement temperature coefficient per c: voltage 25 ppm + 35 v 50 ppm + 85 v 50 ppm + 100 v current 60 ppm + 3 a 60 ppm + 30 a 60 ppm + 12 a mea surement small signal bandwidth: ( C 3 db typical) voltage 10 khz 10 khz 10 khz correction on note 1 10 khz - - current note 2 10 khz 10 khz 10 khz correction on note 1 2 khz - - n6705 mainframe oscilloscope measurement accuracy: (@ 23 c 5 c, accuracy of any individual point in the trace) voltage 0.05% + 32 mv 0.05% + 15 mv 0.05% + 37 mv current 0.1% + 8 ma 0.1% + 52 ma 0.1% + 17 ma correction on note 1 0.1% + 14 ma - - up - programming time with full resistive load: (time f rom 10% t o 90% of total voltage excursion) small voltage step 0 v to 10 v 0 v to 6 v/0 v to 10 v 0 v to 15 v/0 v to 29 v time 0.2 ms 0.4 ms/0.5 ms 0.35 ms/0.7 ms large voltage step 0 v to 50 v 0 v to 20 v 0 v to 60 v time 1.5 ms 1.5 ms 2 ms up - programming sett ling time with full resistive load: (time from start of voltage change to 0.1% of full scale value) small voltage step 0 v to 10 v 0 v to 6 v/0 v to 10 v 0 v to 15 v/0 v to 29 v time 0.5 ms 0.8 ms/1.0 ms 0.8 ms/1.4 ms large voltage step 0 v to 50 v 0 v to 20 v 0 v to 60 v time 4 ms 3 ms 4.2 ms down - programming time with no load: (time f rom start of voltage change to output voltage < 0.5 v) small voltage step 10 v to 0 v 6 v to 0 v/10 v to 0 v 15 v to 0 v/29 v to 0 v time 0.3 ms 0.55 ms/1.0 ms 0.6 ms /1.2 ms large voltage step 50 v to 0 v 20 v to 0 v 60 v to 0 v time 1.3 ms 1.8 ms 2.2 ms
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 22 specifications guide supplemental characteristics (continued) n6751a / n6752a n6753a / n6755a n6754a / n6756a down - programming settling time with no load: (time f rom start of voltage change to 0.1% of full scale value) small voltage step 10 v to 0 v 6 v to 0 v/10 v to 0 v 15 v to 0 v/29 v to 0 v time 0.45 ms 0.8 ms/1.3 ms 0.8 ms/1.5 ms large voltage step 50 v to 0 v 20 v to 0 v 60 v to 0 v time 1.4 ms 2 ms 2.3 ms down - programming time with capacitive load: (time f rom start of voltage change to output voltage < 0.5 v) small voltage step 10 v to 0 v 6 v to 0 v/10 v to 0 v 15 v to 0 v/29 v to 0 v time 2.1 ms 2.2 ms/4.5 ms 2.3 ms/5.5 ms large voltage step 50 v to 0 v 20 v to 0 v 60 v to 0 v time 11 ms 8.5 ms 10 ms capacitive load note 3 1000 f 4700 f 680 f down - programming capability: continuous power 7 w 12.5 w 12.5 w peak current 7 a 15 a 6 a over - voltage protection: accuracy 0.25% + 0.25 v 0.25% + 0.15v 0.25% + 0.3v accuracy with option 761 0.25% + 0.25 v 0.25% + 0.45v 0.25% + 0.6v accuracy with option 760 - 0.25% + 0.45v 0.25% + 0.6v maximum setting 55 v 22 v 66 v response time 50 s from occurrence of over - voltage condition to start of output shutdown output rip ple and noise: (pard) cc rms: 2 ma 10 ma 4 ma common mode noise: (from 20 hz C 20 mhz; from either output to chassis) rms 500 a 500 a 750 a peak - to - peak < 2 ma < 2 ma < 3 ma remote sense capability: outputs can maintain specifications with up to a 1 - volt drop per load lead. the load lead drop reduces the maximum available voltage at the load. series and parallel operation: identically rated outputs can be operated directly in parallel or can be connected for straight series operation.. minimum ou tput turn - on delay: (time from when any output on command is received until the output starts turning on) without relay option 25 ms 18 ms 18 ms with relay option 760 51 ms 44 ms 44 ms 1 correction on compensates for current flowing into the output cap acitor during voltage transients. 2 stated values apply when the load resistance is at or close to zero. to determine the frequency for larger resistance values s, refer to the users guide under measurement system bandwidth. 3 modules can discharge the specified capacitive load from full scale to 0v at a rate of 4 times/second.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 23 autoranging characteristic output impedance graphs 1k 90 45 0 -45 -90 frequency (hz) 10k 100k model n6752a, cc mode, @50v, 2a phase (degrees) phase 100 magnitude 8 4 2 1 0.5 0.25 0.125 impedance (ohms) 0 50 v 10 v 1 a voltage current n 6751 a 50 w output 50 w curve 5 a 0 50 v 12 v 2 a voltage current n 6752 a 100 w output 100 w curve 10 a 8 . 5 v 8 . 33 a 0 20 v 60 v 6 v 15 v voltage current n 6753 a / n 6754 a 300 w output 300 w curve 50 a 20 a 15 a 5 a 0 20 v 60 v 10 v 29 v voltage current 500 w curve 50 a 17 a 25 a 8 . 33 a n 6755 a / n 6756 a 500 w output
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 24 specifications guide model n6753a and n6755a, cv mod e, @20 v, 15a model n6753a and n6755a, option 760, cv mode, @20 v, 15a model n6753a and n6755a, cc mode, @20 v, 15a model n6753a and n6755a, option 760, cc mode, @20 v, 15a
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 25 model n6754a and n6756a, cv mode, @60 v, 5a model n6754a and n6756a, option 760, cv mode, @60 v, 5a model n6754a and n6756a, cc mode, @60 v, 5a m odel n6754a and n6756a, option 760, cc mode, @60 v, 5a
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 26 specifications guide arbitrary waveform generator maximum bandwidth note the information in this section only applies when the p ower modules are installed in a keysight n6705 dc power analyzer. the following tables char acterize the maximum bandwidth of the arbitrary waveform generator. the maximum bandwidth is based on a sine wave into a resistive load and apples to any output current. the following definitions apply in the frequency tables: v p - p = voltage peak - to - peak 3 db max. = max. frequency where the voltage drops to 3 db below its setting thd 3 db = the total harmonic distortion at 3 db max. frequency thd < 1.5% = the frequency below which the thd is less than 1.5%. voltage 3 db max thd 3 db thd < 1.5% n6751 a & n6752a 0.5 vp - p 4000 hz 12% 440 hz 1.0 vp - p 2200 hz 21% 440 hz 2.5 vp - p 900 hz 25% 265 hz 5.0 vp - p 500 hz 27% 160 hz 50.0 vp - p 340 hz 22% 25 hz n6753a & n6755a 0.2 vp - p 2300 hz 10% 1300 hz 0.4 vp - p 1500 hz 15% 800 hz 1.0 vp - p 980 hz 19% 480 h z 2.0 vp - p 580 hz 21% 300 hz 20.0 vp - p 400 hz 12% 32 hz n6754a & n6756a 0.6 vp - p 2800 hz 8.0% 1600 hz 1.2 vp - p 1400 hz 15% 800 hz 3.0 vp - p 600 hz 17% 300 hz 6.0 vp - p 400 hz 20% 200 hz 60.0 vp - p 344 hz 12% 30 hz
27 chapter 4 keysight n67 6 xa precisio n power modules performance specifications ........................................................... 28 supplemental characteristics ........................................................ 29 autoranging chara cteristic ............................................................ 31 output impedance graphs ............................................................. 31 arbitrary waveform generator maximum bandwidth ................... 33 unles s otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40 c after a 30 - minute warm - up period. specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). refer to the keysight n6700 or n6705 service guide for the setup conditions for all performance specifications. supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testi ng. all supplemental characteristics are typical unless otherwise noted.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 28 specifications guide performance specifications n6761a/n6762a n6763a/n6765a n6764a/n6766a dc ratings: voltage 0 - 50 v 0 - 20 v 0 - 60 v current note 1 0 - 1.5 a / 0 - 3 a 0 - 50 a 0 - 20 a / 0 - 17 a power 50 w / 100 w 300 w / 500 w 300 w / 500 w low programming ranges (v & i) 5.5 v; 100 ma - - low measurement ranges (v & i) 5.5 v; 100 ma 2 v; 1.5 a 6 v; 0.5 a output ripple and noise (pard): (from 20 hz C 20 mhz) cv peak - to - peak 4.5 mv 5 mv 6 mv cv rms 0.35 mv 1 mv 1 mv load effect (regulation): (applies for any output load change, with a maximum load - lead drop of 1v/lead. the load lead drop reduces the maximum available voltage at the load. ) voltage 0.5 mv 2 mv 2 mv current 30 a (@ 0 C 7 v) 65 a (@ 7 C 50v) 12 ma 5 ma source effect (regulation): voltage 0.5 mv 0.5 mv 1.2 mv current 30 a 5 ma 2 ma programming accuracy: (@ 23 c 5 c after 30 minute warm - up. applies from minimum to maximum programming range at any load.) voltage, h igh range 0.016% + 6 mv 0.03% + 5 mv 0.03% + 12 mv voltage, low range 0.016% + 1.5 mv - - current, high range 0.04% + 200 a 0.1% + 15 ma 0.075% + 4 ma current, low range 0.04% + 30 a (@ 0 C 7 v) 0.04% + 55 a (@ 7 C 50 v) - - voltmeter/ammeter measurem ent accuracy: (@ 23 c 5 c) applies when measuring 4096 data points with a 20.48 v time interval.) voltage, high range 0.016% + 6 mv 0.03% + 10 mv 0.03% + 25 mv voltage, low range 0.016% + 1.5 mv 0.03% + 1.5 mv 0.03% + 5 mv current, high range 0.04% + 160 a 0.1% + 10 ma 0.1% + 5 ma current, low range 0.03% + 15 a (@ 0 C 7 v) 0.03% + 55 a (@ 7 C 50 v) 0.05% + 1.1 ma note 2 0.05% + 0.75 ma note 2 200 a current range (option 2ua) 0.5% + 100 na - - load transient recovery time: (time to recover to within the settling band following a load change - from 60% to 100% and from 100% to 60% of full load for model n6761a - from 50% to 100% and from 100% to 50% of full load for model n6762a through n6766a) voltage settling band 75 mv 30 mv note 3 90 mv note 4 time < 100 s < 100 s < 100 s 1 output current is derated 1% per c above 40c. 2 applies when measuring currents that remain within the low range. due to thermal settling, when transitioning from measuring full - rated output current ( the worst case), to measuring the current within the low range, the low range accuracy specification is typically met within 5 seconds after the current has transitioned into the low range. accuracies within this 5 second settling period are typically 2x the specified accuracy or better. 3 when relay option 760 or 761 is installed on models n6763aand n6765a, the settling band is 200 mv. 4 when relay option 760 or 761 is installed on models n6764aand n6766a, the settling band is 350 mv.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 29 supplemental ch aracteristics n6761a / n6762a n6763a / n6765a n6764a / n6766a programming ranges: voltage, high range 15 mv C 51 v 10 mv C 20.4 v 25 mv - 61.2 v voltage, low range 12 mv C 5.5 v - - current, high range 1 ma C 1.53 a/1 ma C 3.06 a 50 ma C 51 a 20 ma C 20.4a/2 0ma C 17.3a current, low range note 1 0.1 ma C 0.1 a - - programming resolution: voltage, high range 880 v 1.5 mv 4.2 mv voltage, low range 90 v - - current, high range 60 a 16.3 ma 6.5 ma current, low range 2 a - - measurement resolution: voltag e, high range 440 v 250 v 600 v voltage, low range 44 v 25 v 60 v current, high range 30 a 500 a 250 a current, low range 1 a 20 a 10 a 200 a current range (option 2ua) 4 na - - programming temperature coefficient per c: voltage, high r ange 18 ppm + 140 v 23 ppm + 95 v 23 ppm + 218 v voltage, low range 40 ppm + 70 v - - current, high range 33 ppm + 10 a 25ppm + 129 a 25ppm + 52 a current, low range 60 ppm + 1.5 a - - measurement temperature coefficient per c: voltage, high range 23 ppm + 40 v 23 ppm + 53 v 23 ppm + 73 v voltage, low range 30 ppm + 40 v 25 ppm + 53 v 25 ppm + 73 v current, high range 40 ppm + 0.3 a 25 ppm + 21 a 25 ppm + 7 a current, low range 50 ppm + 0.3 a 27 ppm + 21 a 27 ppm + 7 a current, 200 a range (option 2ua) 100 ppm + 3 na/c - - measurement small signal bandwidth: ( C 3 db typical) voltage 10 khz 10 khz 10 khz correction on note 2 10 khz - - current note 3 10 khz 10 khz 10 khz correction on note 2 2 khz - - n6705 main frame oscilloscope measurement accuracy: (@ 23 c 5 c, accuracy of any individual point in the trace) voltage 0.016% + 16 mv 0.03% + 13 mv 0.03% + 32 mv current, high range 0.04% + 1 ma 0.1% + 16 ma 0.1% + 8.4 ma correction on note 2 0.04% + 10 ma - - current, low range 0.03% + 0.175 ma 0.05% + 6.6 ma 0.05% + 2.6 ma up - programming time with full resistive load: (time f rom 10% to 90% of total voltage excursion) small voltage step 0 v to 10 v 0 v to 6 v/0 v to 10 v 0 v to 15 v/0 v to 29 v time 0.6 ms 0.4 ms/0.5 ms 0.35 ms/0.7 ms large voltage step 0 v to 50 v 0 v to 20 v 0 v to 60 v time 2.2 ms 1.5 ms 2 ms
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 30 specifications guide supplemental characteristics (continued) n6761a / n6762a n6763a / n6765a n6764a / n6766a up - programming settling time with full resistiv e load: (time from start of voltage change to 0.1% of full scale value) small voltage step 0 v to 10 v 0 v to 6 v/0 v to 10 v 0 v to 15 v/0 v to 29 v time 0.9 ms 0.8 ms/1.0 ms 0.8 ms/1.4 ms large voltage step 0 v to 50 v 0 v to 20 v 0 v to 60 v time 4 ms 3 ms 4.2 ms down - programming time with no load: (time f rom start of voltage change to output voltage < 0.5 v) small voltage step 10 v to 0 v 6 v to 0 v/10 v to 0 v 15 v to 0 v/29 v to 0 v time 0.3 ms 0.55 ms/1.0 ms 0.6 ms/1.2 ms large voltage step 50 v to 0 v 20 v to 0 v 60 v to 0 v time 1.3 ms 1.8 ms 2.2 ms down - programming settling time with no load: (time f rom start of voltage change to 0.1% of full scale value) small voltage step 10 v to 0 v 6 v to 0 v/10 v to 0 v 15 v to 0 v/29 v to 0 v tim e 0.45 ms 0.8 ms/1.3 ms 0.8 ms/1.5 ms large voltage step 50 v to 0 v 20 v to 0 v 60 v to 0 v time 1.4 ms 2 ms 2.3 ms down - programming time with capacitive load: (time f rom start of voltage change to output voltage < 0.5 v) small voltage step 10 v to 0 v 6 v to 0 v/10 v to 0 v 15 v to 0 v/29 v to 0 v time 4.5 ms 2.2 ms/4.5 ms 2.3 ms/5.5 ms large voltage step 50 v to 0 v 20 v to 0 v 60 v to 0 v time 23 ms 8.5 ms 10 ms capacitive load note 4 1000 f 4700 f 680 f down - programming capability: cont inuous power 7 w 12.5 w 12.5 w peak current 3.8 a 15 a 6 a over - voltage protection: accuracy 0.25% + 0.25 v 0.25% + 0.15 v 0.25% + 0.3 v with option 761 0.25% + 0.25 v 0.25% + 0.45 v 0.25% + 0.6 v with option 760 - 0.25% + 0.45 v 0.25% + 0.6 v maximum setting 55 v 22 v 66 v response time 50 s from occurrence of over - voltage condition to start of output shutdown output ripple and noise: (pard) cc rms: 2 ma 10 ma 4 ma common mode noise: (from 20 hz C 20 mhz; from either output to chassis) rms 500 a 500 a 750 a peak - to - peak < 2 ma < 2 ma < 3 ma remote sense capability: outputs can maintain specifications with up to a 1 - volt drop per load lead. the load lead drop reduces the maximum available voltage at the load. series and parallel ope ration: identically rated outputs can be operated directly in parallel or can be connected for straight series operation. minimum output turn - on delay : (time from when any output on command is received until the output starts turning on) without relay option 32 ms note 5 18 ms 18 ms with relay option 760 58 ms note 5 44 ms 44 ms 1 if you are operating the unit below 255 a in constant current mode, the output may become unregulated with the following load conditions: the load resistance is <175 m and the load inductance is >20 h. if this occurs, an unregulated flag will be generated and the output current may rise above the programmed value but will remain < 255 a. 2 correction on compensates for current flowing into the output capacitor dur ing voltage transients 3 stated values apply when the load resistance is at or close to zero. to determine the frequency for larger resistance values s, refer to the users guide under measurement system bandwidth. 4 modules can discharge the specified capacitive load from full scale to 0v at a rate of 4 times/second. 5 in current priority mode, minimum delay is 23 ms without relays and 45 ms with relay option 760.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 31 autoranging characteristic output impedance graphs model n6763a and n6765a, cv mode, @20 v, 15a model n6763a and n6765a, option 760, cv mode, @20 v, 15a
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 32 specifications guide model n 6763a and n6765a, cc mode, @20 v, 15a model n6763a and n6765a, option 760, cc mode, @20 v, 15a model n6764a and n6766a, cv mode, @60 v, 5a model n6764a and n6766a, option 760, cv mode, @60 v, 5a model n6764a and n6766a, cc mode, @60 v, 5a model n6764a and n6766a, option 760, cc mode, @60 v, 5a
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 33 arbitrary waveform generator maximum bandwidth note the information in this section on ly applies when the p ower modules are installed in a keysight n6705 dc power analyzer. the following tables characterize the maximum bandwidth of the arbitrary waveform generator. the maximum bandwidth is based on a sine wave into a resistive load and app les to any output current. the following definitions apply in the frequency tables: v p - p = voltage peak - to - peak 3 db max. = max. frequency where the voltage drops to 3 db below its setting thd 3 db = the total harmonic distortion at 3 db max. frequency thd < 1.5% = the frequency below which the thd is less than 1.5%. voltage 3 db max thd 3 db thd < 1.5% n6761a & n6762a 0.5 vp - p 4500 hz 14% 450 hz 1.0 vp - p 3600 hz 14% 450 hz 2.5 vp - p 1300 hz 25% 340 hz 5.0 vp - p 600 hz 25% 250 hz 50.0 vp - p 350 hz 22% 30 hz n6763a & n6765a 0.2 vp - p 2300 hz 10% 1300 hz 0.4 vp - p 1500 hz 15% 800 hz 1.0 vp - p 980 hz 19% 480 hz 2.0 vp - p 580 hz 21% 300 hz 20.0 vp - p 400 hz 12% 32 hz n6764a & n6766a 0.6 vp - p 2800 hz 8.0% 1600 hz 1.2 vp - p 1400 hz 15% 800 hz 3.0 v p - p 600 hz 17% 300 hz 6.0 vp - p 400 hz 20% 200 hz 60.0 vp - p 344 hz 12% 30 hz

35 chapter 5 keysight n678 x a source/measure units performance specifications ........................................................... 36 s upplemental characteristics ........................................................ 38 output quadrant characteristic .................................................... 43 output impedance graphs ............................................................. 44 voltage programming response ................................................... 46 measurement accuracy and resolution ........................................ 48 unless otherwise noted, specifications are warranted over th e ambient temperature range of 0 to 30 c after a 30 - minute warm - up period. unless otherwise noted, s pecifications apply at the mainframe output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). refe r to the keysight n6700 or n6705 service guide for the s etup conditions for all performance specifications . supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. all supplemental characteristics are typical unless otherwise noted.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 36 specifications guide performance specifications n6781a / n6782a n6784a n6785a / n6786a dc ratings: voltage 20 v/6 v 20 v/ 6 v 20 v/15 v/10 v/6 v current note 1 1 a / 3 a 1 a / 3 a 4 a/ 5 a/ 6.7 a/ 8 a power 20 w 20 w 80 w auxiliary voltage measurement input note 2 20 v - 20 v output voltage ripple & noise (pard) from 20 hz C 20 mhz : measured at the output terminals, under all load conditions, in voltage priority mode. output bandwidth setting = low cv peak - to - peak 12 mv 12 mv 15 mv cv rms 1.2 mv 1.2 mv 1.5 mv load effect (load regulation): for any load change, with a lead drop of 1.0 v. the load lead drop reduces the maximum available voltage at the load. voltage, 20 v range 700 v 700 v 700 v v oltage, 15 v & 10 v ranges - - 700 v voltage, 6 v range 400 v 400 v 700 v current, 8 a, 6.7 a, 5 a, & 4 a ranges - - 400 a current, 3 a range 100 a 100 a - current, 1 a range 50 a 50 a - current , 300 ma ranges note 3 50 a - - current , 100 ma & 10 ma ranges note 3 - 1 a - source effect (line regulation): source effect is guaranteed by design. refer to supplemental characteristics later in this chapter. programming accuracy @ 23 c r 5 c : a fter a 30 minute warm - up. applies from minimum to maximum programming range at any load. voltage, 20 v range 0.025% + 1.8 mv 0.025% + 1.8 mv 0.025% + 1.8 mv voltage, 15 v & 10 v ranges - - 0.025% + 1.8 mv voltage, 6v range 0.025% + 600 v 0.025% + 600 v 0.025% + 1.8 mv voltage , 600 mv range note 3 0.025% + 200 v 0.025% + 200 v - current, 8 a, 6.7 a, 5 a, & 4 a ranges - - 0.04% + 1.5 m a current , 3 a & 1 a ranges 0.04% + 300 a 0.04% + 300 a - current , 300 ma range note 3 0.03% + 150 a - - current , 100 ma range note 3 - 0.03% + 12 a - curre nt , 10 ma range note 3 - 0.025% + 5 a - resistance for 20 v output range note 2 0.1% + 3 m? - 0.1% + 1 m? resistance for 15 v & 10 v ranges note 2 - - 0.1% + 1 m? resistance for 6 v output range note 2 0.1% + 1.5 m? - 0.1% + 1 m?
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 37 performance specifi cations (continued) n6781a / n6782a n6784a n6785a / n6786a measurement accuracy @ 23 c 5 c: applies when measuring the default value of 4883 data points with a 20.48 v time interval. refer to measurement accuracy and resolution later in this chapte r for more information. voltage , 20 v range 0.025% + 1.2 mv 0.025% + 1.2 mv 0.025% + 1.8 mv voltage , 1 v range 0.025% + 75 v 0.025% + 75 v - voltage , 100 mv range 0.025% + 50 v 0.025% + 50 v - auxiliary voltage measurement input note 2 0.025% + 5 m v - 0.025% + 5 mv current, 8 a range - - 0.04% + 1.5 m a current , 3 a range 0.03% + 250 0.03% + 250 - current , 100 ma range 0.025% + 10 0.025% + 10 0.025% + 10 current , 1 ma range note 4 0.025% + 100 n a (110 na) 0.025% + 100 n a (110 na) 0 .025% + 100 n a (110 na) current , 10 udqjh note 4 0.025% + 8 n a (20 na) 0.025% + 8 n a (20 na) - load transient response time in voltage priority mode: time to recover to within the settling band. with 150 ) cap (esr=50 m )at load, remote sensing at cap, 4.25' twisted pair load leads - see service guide for setup information. rise time (10% to 90%) 10 v 10 v 10 v settling band 20 v range with a 0.8 a load step 15 v & 10 v range with a 1.4 a load step 6 v range with a 1.4 a load step 1 0 mv - 20 mv 10 mv - 20 mv 20 mv note 5 20 mv 20 mv recovery time v v v 1 output current is derated 1% per c above 30c. 2 applies to n6781a and n6785a only. ggdqdgglwlrqdoyrowdjhsurjudpplqjhuururip9iru1 dqgp9iru1lvdovrsuhvhqw 3 600 mv range is only available in voltage priority mode; 300 ma, 100 ma, 10 ma ranges are only available in current priority mode. 4 values in parentheses apply when power modules are installed in keysight n6705a mainframes. 5 a ppl i es with a 1.4 a load step .
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 38 specifications guide supplemental characteristics n6781a / n6782a n6784a n6785a / n6786a minimum current and voltage compliance limits: 20 v range voltage priority mode 10 ma 10 ma 8 ma 10 v & 15 v ranges voltage priorit y mode - - 8 ma 6 v range voltage priority mode 20 ma 20 ma 8 ma 8 a, 6.7 a, 5 a, & 4 a ranges current priority - - 20 mv 3 a range current priority mode 10 mv 10 mv - 1 a range current priority mode 20 mv 20 mv - programming range & resolution: vol tage, 20 v range 0 to 20.4 v; 200 v - 20.4 v to 20.4 v; 200 v 0 to 20.4 v; 200 v voltage, 15 v range - - 0 to 15.3 v; 200 v voltage, 10 v range - - 0 to 10.2 v; 200 v voltage, 6 v range 0 to 6.12 v; 60 v - 6.12 v to 6.12 v; 60 v 0 to 6.12 v; 200 v voltage, 600 mv range 0 to 612 mv; 6 v - 612 mv to 612 mv; 6 v - current, 8 a range - - - 8.16 a to 8.16 a; 75 a current, 6.7 a range - - - 6.83 a to 6.83 a; 75 a current, 5 a range - - - 5.1 a to 5.1 a; 75 a current, 4 a range - - - 4.0 8 a to 4.08 a; 75 a current, 3 a range - 3.06 a to 3.06 a; 25 a - 3.06 a to 3.06 a; 25 a - current, 1 a range - 1.02 a to 1.02 a; 25 a - 1.02 a to 1.02 a; 25 a - current, 300 ma range - 306 ma to 306 ma; 3 a - - current, 100 ma range - - 102 m a to 102 ma; 1 a - current, 10 ma range - - 10.2 ma to 10.2 ma; 0.1 a - resistance for 20 v range note 1 - 40m? to +1?; 0.5m? - - 40m? to +1?; 0.17m? resistance for 15 v, & 10 v ranges note 1 - - - 40m? to +1?; 0.17m? resistance for 6 v range note 1 - 40 m? to +1?; 0.25m - - 40m? to +1?; 0.17m? programming accuracy temperature coefficient per c: voltage, 20 v range 0.002% +120uv 0.002% +120uv 0.0025% +200uv voltage, 10 v & 15 v ranges - - 0.0025% +200uv voltage, 6 v range 0.0015% +40uv 0.0015% +40uv 0. 0025% +200uv voltage, 600 mv range 0.0015% +10uv 0.0015% +10uv - current, 8 a, 6.7 a, 5 a, & 4 a ranges - - 0.0025% +150ua current, 3 a & 1 a ranges 0.0025% +22ua 0.0025% +22ua - current, 300 ma range 0.0025% +14ua - - current, 100 ma range - 0.0025 % +1ua - current, 10 ma range - 0.0025% +0.5 a - measurement resolution: voltage, 20 v range 200 v 200 v 200 v voltage,1 v range 10 v 10 v - voltage, 100 mv range 1 v 1 v - auxiliary voltage measurement input note 1 800 v - 800 v measurement resolution (continued) current, 8 a range current , 3 a range current, 100 ma range current, 1 ma range current, 10 a range - 25 ua 1 ua 10 na 0.1 na - 25 ua 1 ua 10 na 0.1 na 75 ua - 1 ua 10 na -
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 39 supplemental characteristics (continued) n6781a / n6782a n6784a n6785a / n6786a measurement accu racy temperature coefficient per c: voltage, 20 v range voltage, 1 v range voltage, 100 mv range auxiliary voltage measurement input note 1 0.0025% +25 uv 0.002% +2.5 uv 0.0025% +2.5 uv 0.0007% +200 uv 0.0025% +25 uv 0.002% +2.5 uv 0.0025% +2.5 uv - 0.00 3% +75 uv - - 0.0007% +200 uv current, 8 a range current, 3 a range current, 100 ma range current, 1 ma range current, 10 a range - 0.0025% +14 ua 0.0025% +0.4 ua 0.002% +5 na 0.002% +0.55 na - 0.0025% +14 ua 0.0025% +0.4 ua 0.002% +5 na 0.002% +0.55 na 0.002% +110 ua - 0.0025% +0.4 ua 0.002% +5 na - voltage programming speed & settling time: (at the specified bandwidth) with slew rate set to maximum; with high 2 output cap = 1 uf ; with high 3 output cap = 7 uf compensation setting low high1 high 2 high 3 low high1 high 2 high 3 low high1 high2 high3 rise time from 10% to 90% of step 20 v range with a 0- 10 v step not e 2 15 v & 10 v ranges with a 0- 4 v step 6 v range with a 0- 4 v step 600 mv range with a 0 - 500 mv step 300 s - 300 s 400 s 15 s - 20 s 75 s 20 s - 22 s 30 s 120 s - 50 s 50 s 300 s - 300 s 400 s 15 s - 20 s 75 s 20 s - 22 s 30 s 120 s - 50 s 50 s 300 s 300 s 300 s - 12 s 12 s 12 s - 15 s 15 s 15 s - 40 s 40 s 40 s - se ttling time to 0.1% of step 20 v range with a 0- 10 v step note 2 15 v, & 10 v ranges with a 0- 4 v step 6 v range with a 0- 4 v step 600 mv range with a 0 - 500 mv step 850 s - 850 s 1.2 ms 45 s - 55 s 220 s 65 s - 65 s 85 s 240 s - 160 s 170 s 850 s - 850 s 1.2 ms 45 s - 55 s 220 s 65 s - 65 s 85 s 240 s - 160 s 170 s 1.2ms 1.2ms 1.2ms - 40 s 40 s 40 s - 50 s 5 0 s 50 s - 120 s 120 s 120 s - high frequency output voltage noise: (at the specified bandwidth ) with high 2 setting, output cap = 1 uf ; with high 3 setting, output cap = 7 uf compensation setting low high1 high 2 high 3 low high1 high 2 high 3 low high1 high2 high3 cv peak - to - peak from 20hz - 20 mhz 20 v range with any load 15 v & 10 v ra nges with any load 6 v range with any load 600 mv range with any load 12 mv - 12 mv 12 mv 12 mv - 12 mv 12 mv 4 mv - 4 mv 4 mv 4 mv - 3 mv 3 mv 12 mv - 12 mv 12 mv 12 mv - 12 mv 12 mv 4 mv - 4 mv 4 mv 4 mv - 3 mv 3 mv 15mv 15mv 15mv - 15m v 15mv 15mv - 3 mv 3 mv 3 mv - 3 mv 3 mv 3 mv - cv rms from 20 hz C 20 mhz 20 v range with any load 15 v & 10 v ranges with any load 6 v range with any load 600 mv range with any load 1.2 mv - 1 mv 1 mv 1.2 mv - 1 mv 1 mv 0.5 mv - 0.3 mv 0.3 mv 0.5 mv - 0.3 mv 0.3 mv 1.2 mv - 1 mv 1 mv 1.2 mv - 1 mv 1 mv 0.5 mv - 0.3 mv 0.3 mv 0.5 mv - 0.3 mv 0.3 mv 1.5mv 1.5mv 1.5mv - 1.5mv 1.5mv 1.5mv - 0.4mv 0.4mv 0.4mv - 0.3mv 0.3mv 0.3mv - low frequency output voltage noise: cv peak to peak from 0.1 hz C 10 hz 20 v range 6 v range 600 mv range - - - 100 v 50 v 20 v - - - cv rms from 0.1 hz C 10 hz 20 v range 6 v range 600 mv range - - - 20 v 10 v 5 v - - - voltage programming small signal bandw idth: refer to voltage programming response later in this chapter.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 40 specifications guide supplemental characteristics (continued) n6781a / n6782a n6784a n6785a / n6786a voltage measurement noise: (peak value) 20 v range 1 v range 100 mv range 3 mv 250 v 50 v 3 mv 250 v 50 v 2.9 mv - - voltage measurement settling time: (all ranges) settling time with no range change 40 s 40 s 35 s voltage measurement small signal bandwidth: (all ranges) C 3 db typical with seamless ranging off with seamless r anging on dc to 30 khz dc to 27 khz dc to 30 khz - dc to 30 khz - C 1 db typical with seamless ranging off with seamless ranging on dc to 17 khz dc to 15 khz dc to 17 khz - dc to 17 khz - voltage priority transient characteris tic : ( time to recover to within the settling band ) at the specified bandwidth, 6 v range only, with remote sensing at load cap, 4.25' twisted pair load leads . compensation setting low high1 high2 high3 low high1 high2 high3 low high1 high2 high3 settlin g band. 40 mv 50 mv 30 mv 20 mv 40 mv 50 mv 30 mv 20 mv 40 mv 50 mv 30 mv 20 mv cc load step 0.2 a 0.2 a 0.5 a 1.4 a 0.2 a 0.2 a 0.5 a 1.4 a 0.2 a 0.2 a 0.5 a 1.4 a rise time from 10% to 90% of step 10 s 5 s 5 s 10 s 10 s 5 s 5 s 10 s 10 s 5 s 5 s 10 s recovery time with no load cap with 1 f load cap (esr=50 m ?) with 6.8 f load cap (esr=50 m ?) with 150 f load cap (esr=50 m ?) 30 s - - 140 s 10 s 20 s - - - 10 s 25 s - - - 15 s 35 s 30 s - - 140 s 10 s 20 s - - - 10 s 25 s - - - 15 s 35 s 40 s - - 150 s 12 s 20 s - - - 12 s 14 s - - - 15 s 25 s maximum peak voltage deviation with no load cap with 1 f load cap (esr=50 m ? ) with 6.8 f load cap (esr=50 m ?) with 150 f load cap ( esr=50 m ?) 180 mv - - 45 mv 200 mv 260 mv - - - 140 mv 140 mv - - - 60 mv 45 mv 180 mv - - 45 mv 200 mv 260 mv - - - 140 mv 140 mv - - - 60 mv 45 mv 250mv - - 65 mv 260mv 290mv - - - 140mv 140mv - - - 60 mv 45 mv auxiliary voltage measureme nt input: note 1 differential input resistance maximum conversion rate maximum voltage from common maximum continuous input without damage 10 m? 100k samples/second 240 vdc 60 v - - - - 10 m? 100k samples/second 240 vdc 60 v over - voltage protecti on: accuracy maximum setting response time note 3 programmable delay range & default value 0.05% + 20 mv 24 v <30 p s 30 to 272 p s; 30 p s 0.05% + 20 mv 24 v <30 p s 30 to 272 p s; 30 p s 0.05% + 20 mv 24 v <30 p s 30 to 272 p s; 30 p s source effect (line regul ation) : voltage, all ranges current, all ranges 300 v 60 a 300 v 60 a 100 v 100 a current programming speed & settling time: rise time from 10% to 90% of step 8 a range with a 0- 8 a step 3 a range with a 0 - 3 a step 1 a range with a 0 - 1 a step 3 00 ma range with a 0 - 300 ma step 1 00 ma range with a 0 - 100 ma step 10 ma range with a 0- 10 ma step - 2.8 s 3.2 s 3.5 s - - - 2.8 s 3.2 s - 4 s 5 s 3.0 s - - - - -
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 41 supplemental characteristics (continued) n6781a / n6782a n6784a n6785a / n6786a current programming speed & s ettling time (continued) settling time to 0.1% of step 8 a range with a 0- 8 a step 3 a range with a 0 - 3 a step 1 a range with a 0 - 1 a step 3 00 ma range with a 0 - 300 ma step 100 ma range with a 0- 100 ma step 10 ma range with a 0 - 10 ma step - 30 s 30 s 40 s - - - 30 s 30 s - 30 s 30 s 20 s - - - - - high frequency output current noise: (all ranges) cc rms from 20 hz C 20 mhz 200 a 200 a 1 ma low frequency output current noise: ( cc rms from 0.1 hz C 10 hz) 3 a & 1 a ranges 100 ma range 10 ma range - - - 2 a 50 na 20 na - - - current programming small signal bandwidth: C 3 db all except 100 ma & 10 ma range for 100 ma & 10 ma range dc to 120 khz - dc to 120 khz dc to 100 khz dc to 130 khz - C 1 db all except 100 ma & 10 ma range for 100 ma & 10 ma range dc to 75 khz - dc to 75 khz dc to 50 khz dc to 70 khz - current measurement noise: (peak value) 8 a range 3 a range 100 ma range 1 ma range 10 a range - 400 a 20 a 2 a 20 n a - 400 a 20 a 2 a 20 n a 1.2 ma - 13.5 a 1.4 a - current measurement settling time: (to 1% of the specified step with no range change or with up - ranging) 8 a range with 0.5 - 1a step 3 a range with a 0.5 - 1 a step 100 ma range with a 50 - 100 ma step 1 ma range with a 0.5 - 1 m a step 10 a range with a 5 - 10 a step - 35 s 35 s 120 s 750 s - 35 s 35 s 120 s 750 s 35 s - 35 s 120 s - up - ranging to 8 a range with a 0- 8 a step 3 a range with a 0- 3 a step 100 ma range with a 0- 100 ma step 1 ma range with a 0 - 1 ma step - 35 s 35 s 120 s - - - - 35 s - 35 s - (to 1% of the specified range with down - ranging) down - ranging from 3 a & 8 a ranges to: 100 ma range 1 ma range 10 a range 45 s 200 s 3.5 ms 45 s 200 s 3.5 ms 50 s 200 s - current measurement small signal bandwidth: note 4 C 3 db typical with seamless ranging off 8 a range 3 a range 100 ma range 1 ma range 10 a range - dc to 29 khz dc to 29 khz dc to 10 khz dc to 750 hz - dc to 27 khz d c to 27 khz dc to 10 khz dc to 750 hz dc to 28 khz - dc to 30 khz dc to 10 khz -
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 42 specifications guide supplemental characteristics (continued) n6781a / n6782a n6784a n6785a / n6786a current measurement small signal bandwidth (continued) C 3 db typical with seamless ranging on 8 a range 3 a range 100 ma range 1 ma range - dc to 26 khz dc to 26 khz dc to 10 khz - - - - dc to 26 khz - dc to 27 khz dc to 10 khz C 1 db typical with seamless ranging off 8 a range 3 a range 100 ma range 1 ma range 10 a range - dc to 16 khz dc to 16 khz dc to 6 khz dc to 400 hz - dc to 16 khz dc to 16 khz dc to 6.5 khz dc to 400 hz dc to 16 khz - dc to 17 khz dc to 6 khz - C 1 db typical with seamless ranging on 8 a range 3 a range 100 ma range 1 ma range - dc to 14 khz dc to 14 khz dc to 6 khz - - - - dc to 15 khz - dc to 15 khz dc to 16 khz current priority transient characteristic: (with 4.25' twisted pair load leads) 8 a range with a 5 - 15 v step current settling band recovery time note 5 - - - - 40 ma 5 s (7 s) 3 a range with a 1 - 4 v step current settling band recovery time note 5 5 ma 12 s (24 s) 5 ma 12 s (24 s) - - 1 a range with a 0.5 - 0 v step current settling band recovery time note 5 10 ma 12 s (24 s) 10 ma 12 s (2 4 s) - - common mode current from 20 hz C 20 mhz: (with negative output connected to chassis) cc peak - to - peak < 1 ma < 1 ma < 1.5 ma cc rms < 100 a < 100 a < 150 a remote sense capability: outputs can maintain specifications with up to a 1 - volt drop per load lead. the load lead drop reduces the maximum available voltage at the load. parallel operation: note 6 identically rated outputs can be operated directly in parallel in c urrent p riority mode only . operating units in series is not available. minimum output turn - on delay: (time from when any output on command is received until the output starts turning on.) turn - off mode set to low impedance 25.6 ms 25.6 ms 25.6 ms turn - off mode set to high impedance 24.7 ms 24.7 ms 24.7 ms 1 applies to n 6781a and n6785a only 2 for n6785a and n6786a applies with a 0 - 4 v step. 3 response time applies from the occurrence of the over - voltage condition to the start of output shutdown. 4 when using an n6705a mainframe connected through the front panel bindin g posts, additional output capacitance causes large measurement peaking/overshoots when the load impedance is > ~1 k?. this does not apply to n6705b mainframes. when using an n6705a or n6705b mainframe connected directly to the module connector, there are slight measurement peaking/overshoots when the load impedance is > ~10 k?. 5 values in parentheses apply when po wer modules are installed in n6705a mainframes. 6 in cv priority mode, uneven current sharing while paralleling prevents using the lower current measurement ranges and will also cause degradation in transient response performance.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 43 output quadrant character istic + 20 v + 6 v voltage current n 6781 a , n 6782 a , 20 w - 3 a - 1 a 0 key sourcing power sinking power + 1 a + 3 a 0 + 6 v current n 6784 a , 20 w + 3 a - 3 a - 6 v + 20 v voltage + 1 a - 20 v - 1 a note 1 + 20 v + 6 v voltage current n 6785 a , n 6786 a , 80 w + 8 a , + 4 a , - 8 a 0 + 10 v + 15 v + 6 . 7 a , + 5 a , - 6 . 7 a - 5 a - 4 a + 2 . 2 v - 2 . 3 a current voltage n 6784 a down - programmer derating + 15 v - 0 . 9 a + 0 . 9 a - 15 v + 2 . 3 a - 2 . 2 v note 1. when sinking power, keysight model n6784a can operate at the maximum rated output power for only a limited time. when th e internal temperature of the unit exceeds its safe limit, the output latches off. a protect clear is required to resume normal operation. the condition is annunciated by the ot status bit. the downprogrammer derating figure shows the safe limit boundary values.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 44 specifications guide output impedance graphs n6781a n6782a n6784a cv mode @3v, 0.5a n6781a n6782a n6784a cc mode @2.4v, 0.4a
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 45 n6785a n6786a cv mode @3v, 0.5a n6785a n6786a cc mode @2.4v, 0.4a
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 46 specifications guide voltage programming response the following graphs show the volta ge programming response with the indicated bandwidths and loads. note that the load esr=200 m ?. n6781a n6782a n6784a bandwidth low high 1 n6781a n6782a n6784a bandwidth high 2 high 3
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 47 n6785a n6786a bandwidth low high 1 n6785a n6786a bandwidth high 2 high 3
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 48 specifications guide measurement accuracy and resolution ( with shorter measurement intervals ) the following table shows changes to the short - term measurement accuracy and resolution with various number of power line cycle (nplc) measurement settings. changes are due to the a - to - d converters noise performance. the tables baseline is 1 nplc with no added noise. to determine the measurement accuracy at shorter averaging intervals, simply add the noise value to the fixed accuracy value in the specification table. n 6785a and n6786a nplc @ 60 hz: 0.0003 0.003 0.006 0.010 0.031 0.06 0.1 0.6 1 time: 5.1e - 6 51.2e - 6 102.4e - 6 169e - 6 512e - 6 998.4e - 6 1.7e - 3 10e - 3 16.7e - 3 averaged points: 1 10 20 33 100 195 325 1953 3255 20v range noise: 2.9e - 3 1.3e - 3 1.0e - 3 1.0e - 3 394.2e - 6 298.5e - 6 260.6e - 6 98.1e - 6 69.8e - 6 resolution (bits): 12.7 13.9 14.2 14.2 15.6 16 16.2 17.6 18.1 8a range noise: 1.2e - 3 552.2e - 6 409.7e - 6 313.8e - 6 198.9e - 6 138.0e - 6 94.4e - 6 45.6e - 6 43.5e - 6 resolution (bits): 12.7 13.8 14.2 14.6 15.2 15.8 16.3 17.4 17.4 100ma range noise: 13.5e - 6 7.1e - 6 5.4e - 6 4.1e - 6 2.5e - 6 1.7e - 6 1.3e - 6 644.2e - 9 471.5e - 9 resolution (bits): 12.8 13.7 14.1 14.5 15.2 15.8 16.2 17.2 17.6 1ma range noise: 1.4e - 6 594.3e - 9 306.2e - 9 191.0e - 9 67.7e - 9 38.8e - 9 23.8e - 9 8.2e - 9 6.9e - 9 resolution (bits): 9.4 10.7 11.6 12.3 13.8 14.6 15.3 16.8 17.1 n6781a, n6782a and n6784a nplc @ 60 hz: 0.0003 0.003 0.006 0.010 0.031 0.06 0.1 0.6 1 time: 5.1e - 6 51.2e - 6 102.4e - 6 169e - 6 512e - 6 998.4e - 6 1.7e - 3 10e - 3 16.7e - 3 averaged points: 1 10 20 33 100 195 325 1953 3255 20v range noise: 2.3e - 3 1.2e - 3 993.7e - 6 894.8e - 6 533.4e - 6 297.5e - 6 276.6e - 6 87.4e - 6 69.6e - 6 resolution (bits): 13 14 14.2 14.4 15.1 16 16.1 17.7 18.1 1v range noise: 186.6e - 6 90.3e - 6 57.0e - 6 45.5e - 6 26.7e - 6 22.1e - 6 19.8e - 6 7.1e - 6 4.8e - 6 reso lution (bits): 12.3 13.4 14 14.4 15.1 15.4 15.6 17.1 17.6 100mv range noise: 38.9e - 6 20.7e - 6 12.5e - 6 10.5e - 6 5.9e - 6 5.1e - 6 5.0e - 6 3.9e - 6 3.4e - 6 resolution (bits): 11.3 12.2 12.9 13.2 14 14.2 14.2 14.6 14.8 3a range noise: 480.3e - 6 206.4e - 6 159.7e - 6 120. 5e - 6 71.0e - 6 48.3e - 6 41.4e - 6 16.8e - 6 18.5e - 6 resolution (bits): 12.6 13.8 14.2 14.6 15.3 15.9 16.1 17.4 17.2 100ma range noise: 14.1e - 6 8.7e - 6 6.4e - 6 4.4e - 6 2.5e - 6 2.2e - 6 1.5e - 6 858.1e - 9 573.3e - 9 resolution (bits): 12.8 13.4 13.9 14.4 15.2 15.4 16 16.8 17.4 1ma range noise: 1.8e - 6 798.7e - 9 363.1e - 9 248.5e - 9 74.1e - 9 44.8e - 9 27.3e - 9 8.5e - 9 6.8e - 9 resolution (bits): 9.1 10.2 11.4 11.9 13.7 14.4 15.1 16.8 17.1 10 u a range noise: 15.9e - 9 18.0e - 9 20.3e - 9 15.4e - 9 11.0e - 9 4.8e - 9 3.3e - 9 752.2e - 12 456.3e - 12 res olution (bits): 9.2 9.1 8.9 9.3 9.8 11 11.5 13.7 14.4
49 chapter 6 keysight n6783a - bat, n6783a - mfg application - specific power modules performance specifications ........................................................... 50 supplemental characteristics ........................................................ 51 output quadrant characteristic .................................................... 52 unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40 c after a 30 - minute warm - up period. specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). refer to the keysight n6700 or n6705 service guide for the setup c onditions for all performance specifications. supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. all supplemental characteristics are typical unless otherwise noted.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 50 specifications guide performanc e specifications n6783a - bat n6783a - mfg dc ratings: voltage 0 - 8 v 0 - 6 v current note 1 C 2 to +3 a C 2; 0 to +3 a power 24 w 18 w low current measurement range 150 ma 150 ma output ripple and noise (pard): (from 20 hz C 20 mhz) cv peak - to - peak 8 mv 8 mv cv rms 1.5 mv 1.5 mv load effect (regulation): ( f or any output load change, with a maximum load - lead drop of 0.5v/lead . the load lead drop reduces the maximum available voltage at the load. ) voltage 6 mv 6 mv current 2 ma 2 ma source effect (regulation): voltage 2 mv 2 mv current 1 ma 1 ma programming accuracy: (@ 23 c 5 c a fter a 30 minute warm - up . applies from minimum to maximum programming range at any load. ) voltage 0.1% + 10 mv 0.1% + 10 mv positive current 0.1% + 1.8 ma 0.1% + 1.8 ma negative current @ C 2 a 0.2% + 1.8 ma n/a measurement accuracy: (@ 23 c 5 c . applies when measuring the default value of 1024 data points with a 20.48 v time interval. ) voltage 0.05% + 5 mv 0.05% + 5 mv current high range 0.1% + 600 a 0.1% + 600 a current low range 0.1% + 75 a 0.1% + 75 a load transient recovery (time to recover to within settling band for a load change from 0.15 a to 1.5 a and from 1.5 a to 0.15 a at 6 v output) voltage settling band note 2 75 mv 75 mv time note 2 < 45 s < 45 s 1 output current is derated 1% per c above 40c. 2 when relay option 761 is installed, the settling band is 90 mv . the time is < 75 s .
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 51 supplemental characteristics n6783a - bat n6783a - mfg programming ranges: voltage 15 mv to 8.16 v 15 mv to 6.12 v positive current 5 ma to 3.06 a 5 ma to 3.06 a negative current C 5 ma to C 2 a fixed at C 2 a programming resolution : voltage 2.5 mv 2.5 mv positive current 1 ma 1 ma negative current 10 ma n/a measurement resolution: voltage 300 v 300 v current high range 100 a 100 a current low range ( 0.150 a) 5 a 5 a programming temperature coefficient per c : voltage 25 ppm + 50 v 25 ppm + 50 v current 25 ppm + 10 a 25 ppm + 10 a measurement temperature coefficient per c: voltage 25 ppm + 40 v 25 ppm + 40 v current high range 25 ppm + 2.5 a 25 ppm + 2.5 a current low range ( 0.150 a) 2 5 ppm + 1.5 a 25 ppm + 1.5 a maximum up - programming and down - programming time with full resistive load ( t ime from 10% to 90% of total voltage excursion) voltage settling from 0v to full scale 4.0 ms 4.0 ms voltage settling from full scale to 0v 4.0 ms 4.0 ms maximum up - programming and down - programming settling time with full resistive load ( t ime from start of voltage change until voltage settles within 0.1% of the full - scale voltage of its final value) voltage settling from 0v to full scale 20 m s 20 ms voltage settling from full scale to 0v 20 ms 20 ms over - voltage protection: accuracy without disconnect relays 0.25% + 75 mv 0.25% + 75 mv accuracy with disconnect relays 0.25% + 275 mv 0.25% + 275 mv nominal range 0 C 10 v 0 C 10 v prog rammable delay time 60 s C 5 ms 60 s C 5 ms over - current protection: programmable delay time 0 C 255 ms 0 C 255 ms nominal range 5 ma C 3.06 a 5 ma C 3.06 a output ripple and noise: (pard) cc rms: 4 ma 4 ma common mode noise: ( f rom 20 hz C 20 mhz; from either output to chassis) rms 1 ma 1 ma peak - to - peak 6 ma 6 ma remote sense capability: outputs can maintain dc specifications with up to a 0.5 - volt drop per load lead. maximum sense lead resistance is limited to pohdg
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 52 specifications guide supplement al characteristics (continued) n6783a - bat n6783a - mfg series and parallel operation: identically rated outputs can be operated directly in parallel. n6783a modules cannot be used in series with other n6783a modules or any other n67xx module. down - pr ogramming capability: ( c urrent down - programming capability is reduced a t output voltages b elow 0.5 v) continuous power 12 w 12 w continuous current 2 a 2 a output quadrant characteristic key sourcing power sinking power + 8 v (bat ) current + 3 a -2 a 0 n 6783 a -bat n 6783 a - mfg + 6 v ( mfg ) negative current not programmable on n 6783 a - mfg voltage
53 chapter 7 keysight n6700 modular power system mainframes supplemental characteristics ........................................................ 54 outline diagrams ............................................................................ 56 supplemental characteristics are not warranted but are descriptions of perfor mance determined either by design or by type testing. all supplemental characteristics are typical unless otherwise noted. note refer to the following documents for information about using and servicing the keysight n6700 modular power system mainframes keysight model n6705 dc power analyzer users guide go to http:// literature.cdn.keysight.com /litweb/pdf/n6705 - 90001.pdf . keysight model n6705 dc power analyzer service guide go to http:// literature.cdn.keysight.com /litweb/pdf/n6705 - 90010.pdf . keysight series n6700 low - profile modular power system users guide go to http:// literature.cdn.keysight.com /litweb/pdf/5969 - 2937.pdf . keysight series n6700 low - profile modular power system service guide go to http:// literature.cdn.keysight.com /litweb/pdf/5969 - 2938.pdf .
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 5 4 specifications guide supplemental characteristics n6700b, n6701a, n6702a n6705a, n6705b maximum power available for modules: values represent combined power rating of all modules installed per mainframe. 400 w (for n670 0 b mainframes) 600 w (for n6701a mainframes) 1200 w (for n6702a mainframes) 600 w front panel output terminals: maximum current rating n/a 20 a bnc trigger connectors: i/o maximum voltage n/a n/a digital ttl level compatible 5 v usb current ratings: front panel usb connector rear panel usb connector n/a n/a 200 ma 300 ma data storage: internal flash memory 8 mbyte 4 g byte (earlier n6705 models have less memory) protection response characteristic: inh input fault on coupled outputs 5 s f rom receipt of inhibit to start of shutdown < 10 s from receipt of fault to start of shutdown command processing time: pviurpuhfhlswrifrppdqgwrvwduwrirxwsxwfkdqjh digital port characteristics: maximum voltage ratings pins 1 and 2 as fl t output pins 1 - 7 as digital/trigger outputs (pin 8 = common) pins 1 - 7 as digital/trigger inputs and pin 3 as inh input (pin 8 = common) +16.5 vdc/ ? 5 vdc between pins (pin 8 is internally connected to chassis ground). maximum low - level outpu t voltage = 0.5 v @ 4 ma maximum low - level sink current = 4 ma typical high - level leakage current = 1 ma @ 16.5 vdc maximum low - level output voltage = 0.5 v @ 4 ma; 1 v @ 50 ma; 1.75 v @ 100 ma maximum low - level sink current = 100 ma typical high - level l eakage current = 0.8 ma @ 16.5 vdc maximum low - level input voltage = 0.8 v minimum high - level input voltage = 2 v typical low - level current = 2 ma @ 0 v (internal 2.2k pull - up) typical high - level leakage current = 0.12 ma @ 16.5 vdc interface capabiliti es: gpib lxi compliance usb 2.0 10/100 lan built - in web server scpi - 1993, ieee 488.2 compliant interface class c (only applies to units with lxi label on front panel) requires keysight io library version m.01.01 or 14.0 and up requires keysight io libra ry version l.01.01 or 14.0 and up requires internet explorer 7+ or firefox 2+
n 6731b - n6786a dc power modules n6700b - n6705b mainframes specif ications guide 55 supplemental characteristics (continued) n6700b, n6701a, n6702a n6705a, n6705b regulatory compliance: emc safety complies with european emc directive for test and me asurement products. iec/en 61326 - 1 cispr 11 , group 1, class a as/nzs cispr 11 ices/nmb - 001 complies with australian standard and carries c - tick mark. this ism device complies with canadian ices - 001. cet appareil ism est conforme la norme nmb - 001 du canada. complies with european low voltage directive and carries the ce - marking. conforms to ul 61010 - 1 and csa c22.2 61010 - 1. environmental conditions operating environment temperature range relative humidity altitude storage temperature indoor use, installatio n category ii (for ac input), pollution degree 2 0 q c to 55 q c (output current is derated 1% per c above 40c ambient temperature) up to 95% up to 2000 meters - 30q c to 70 qc acoustic noise declaration: this statement is provided to comply with the requirements of the german sound emission directive, from 18 january 1991. sound pressure lp <70 db(a), at operator position, normal operation, according to en 27779 (type test). schalldruckpegel lp <70 db(a), am arbeitsplatz, normaler betrieb, nach en 27779 (typprfung). output terminal isolation : maximum rating no output terminal may be more than 240 vdc from any other terminal or chassis ground. n6781a note when using the aux measurement input terminals on model n6781a, no output or input terminal may be more than 6 0 vdc from any other terminal and chassis ground. ac input : input ratings power consumption power factor fuse ~ 100 vac C 240 vac; 50/60/400hz 1 00 0 va (n6700b) 1 44 0 va (n6701a) 1440 va (n6702a @ < 180 vac inp ut) 22 00 va (n6702a @ > 180 vac input ) 0.99 @ nominal input and rated power internal fuse - not customer accessible. ~ 100 vac C 240 vac; 50/60/400hz 1 44 0 va 0.99 @ nominal input and rated power internal fuse - not customer accessible. n6702a note a c mains circuits rated at 100 - 1 8 0 vac cannot supply enough current to power the n6702a mainframe when operated at its full rated power. when connected to a 100- 1 8 0 vac mains , internal circuits will limit the power to modules to 600 w maximum . net weight : (typical) mainframe with 4 modules single - wide power module n6700b 12.73 kg / 28 lbs n6701a 11.82 kg / 26 lbs n6702a 14.09 kg / 31 lbs 1.23 kg / 2.71 lbs 16 kg / 35 lbs 1.23 kg / 2.71 lbs dimensions : refer to the outline diagrams on the following page.
n 6731b - n6786a dc power modules n6700b - n6705b mainframes 56 specifications guide outline diagrams 272 . 6 mm 10 . 733 in . 425 . 6 mm 16. 756 in . 177 . 0 mm 6 . 968 in . 17. 7 mm 0 . 697 in . 16. 9 mm 0 . 663 in . 23. 5 mm 0 . 923 in . = airflow
this information is subject to change without notice. ? keysight technologies 2010 - 2015 edition 8, january 2015 n6700 - 90001 www.keysight.com

▲Up To Search▲

Price & Availability of N6731B

	To Download N6731B Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .