d1u86p-w-1600-12-hbxdc series 86mm 1u front end ac-dc power supply d1u86p-w-1600-12-hbxdc.a01 page 1 of 6 www.murata-ps.com/support www.murata-ps.com for full details go to www.murata-ps.com/rohs $ ordering guide part number power output; ac line main output standby output airflow (90-264v) (108-264v) (180-264v) d1u86p-w-1600-12-hb4dc 1200w 1350w 1600w 12v 12v back to front d1u86p-w-1600-12-hb3dc front to back input characteristics parameter conditions min. nom. max. units input voltage operating range 90 115/230 264 vac frequency 47 50/60 63 hz turn-on voltage ramp up 81 89 vac turn-off voltage ramp down 70.5 73 78 maximum input current 1200w, 100vac 14.1 arms inrush current at 264vac at 25c cold start 35 apk power factor at 230vac, half load 0.98 efficiency (230vac) excluding fan load 20% load 90 % 50% load 94 100% load 91 output voltage characteristics output voltage parameter conditions min. typ. max. units 12v voltage set point 50% load 12.17 12.2 12.23 vdc line and load regulation 11.4 12.6 droop 3.10 mv/a ripple voltage & noise 1 20mhz bandwidth 120 mv p-p output current (230 vac) 2 0 133.4 a output current (120 vac) 2 0 112.5 a output current (100 vac) 2 0 100.0 a load capacitance 10,000 f 12vsb voltage set point 50% load 11.97 12.0 12.02 vdc ripple voltage & noise 1 20mhz bandwidth 120 mv p-p output current 0 2.5 a 1 ripple and noise measured with a parallel combination of a 1.0f ceramic and 10f tantalum capacitor on each of the power modu le outputs. a short coaxial cable connected directly to the input of a scope is required. 2 to meet ripple and transient step load speci? cations a minimum load of 4a is required. features ? ? 1600w output power ? ? 94% minimum ef? ciency at 50% load ? ? 12v main output ? ? 12v standby output of 30w ? ? 1u height: 3.4" x 7.75" x 1.59" ? ? 38.6 watts per cubic inch density ? ? n+1 redundancy, including hot plugging (up to 8 in parallel) ? ? current sharing on 12v main output ? ? overvoltage, overcurrent, overtemperature protection ? ? internal cooling fan (variable speed) ? ? pmbus? / i2c interface monitoring and control ? ? rohs compliant product overview the d1u86p-w-1600-12-hbxdc products are high ef?ciency 1600 watt, power factor corrected front end supplies with a 12v main output and a 12v (30w) standby. they have current sharing and up to 8 supplies may be operated in parallel. the supplies may be hot plugged, they recover from overtemperature faults, and have logic and pmbus monitoring and control. their low pro?le 1u package and >38.6w/cubic inch power density make them ideal for delivering reliable, ef?cient power to servers, workstations, storage systems and other 12v distributed power systems. cb test certi cate and test report www.murata-ps.com / en / 3d / acdc.htm l www.murata-ps.com / en / 3d / acdc.htm l www.murata- p s.com/en/3d/acdc.htm l www.murata-ps.com / en / 3d / acdc.htm l www.murata- p s.com/en/3d/acdc.htm l www.murata-ps.com / en / 3d / acdc.htm l available now at http://power.murata.com/en/3d/acdc.html
d1u86p-w-1600-12-hbxdc series 86mm 1u front end ac-dc power supply d1u86p-w-1600-12-hbxdc.a01 page 2 of 6 www.murata-ps.com/support output characteristics parameter conditions min. typ. max. units output rise monotonicity no voltage excursion startup time ac ramp up 1.5 3 s transient response 12v, 50% load step, 1.0as di/dt 600 mv 12vsb, 50% load step,1.0as di/dt 600 current sharing accuracy (up to 8 in parallel) 3 at 100% load 5 % hot swap transients all outputs remain in regulation 5 % holdup time at full load 12 ms 3 load current of 100% applies to each power module max load connected in an n+1 con? guration; therefore the total load will be n x 100% . the share accuracy of 5% is a ? xed percentage irrespective of total loading and number of units connected in parallel. environmental characteristics parameter conditions min. typ. max. units storage temperature range -40 85 c operating temperature range 055 operating humidity noncondensing 5 90 % storage humidity 595 altitude (without derating at 45c) 3000 m shock 30g non operating vibration 10-500hz, 0.5g (non-operational) mtbf per telcordia sr-322 m1c1@ 40c 559k hrs acoustic 65 dba/@1m safety approvals csa 60950-1-07+a1:2011 ansi/ul 60950-1-2011, second edition iec 60950-1:2005 (2nd edition) + a1:2009 en 60950-1:2006 +a11:2009 +a1:2010 input fuse power supply has internal 16a/250v fast blow fuse on the ac line input weight 2.33/1.06 lbs/kg protection characteristics output voltage parameter conditions min. typ. max. units overtemperature (intake) an otp warning will be issued via the pmbus? interface when the air inlet exceeds 65c; however the power module shall not shut down until critical internal hotspot temperatures are exceeded. 65 c 12v overvoltage latching 13.2 14.4 v overcurrent at 220vac shutdown of the output followed by auto- recovery after one second. the output shall attempt three such auto-recovery attempts and then enter a per- manent latched state. recovery of the permanent latched state shall require cycling of the incoming ac source or toggling of the pson# signal. 140 153 a overcurrent at 120vac 118 129 12vsb overvoltage latching 13.2 14.4 v overcurrent autorecovery 2.75 3 a isolation characteristics parameter conditions min. typ. max. units insulation safety rating / test voltage input to output - reinforced 3000 vrms input to chassis - basic 1500 vrms isolation output to chassis 500 vdc leakage current 1.5ma at 264vac, 50/60hz
d1u86p-w-1600-12-hbxdc series 86mm 1u front end ac-dc power supply d1u86p-w-1600-12-hbxdc.a01 page 3 of 6 www.murata-ps.com/support status indicators and control signals signal description pson# low = main output on; pson# can be permanently tied to gnd within the host system. present# short pin pulled down on p/s; pulled up to either 3.3v or 12v (max) in the host system. for 3.3v use a 5.11k resistor; for 12v , use a 21k resistor. ps interrupt open drain pmbus? signal; can be left open if not used. addr pmbus? address; addr can be grounded or left open if not used. if grounded, the address will be 000, if it is open, the default address will be 111. ishare analog representation of main output current; can be left open if not used. psok 4 a three level signal based on ac input and dc output status; can be left open if not used. i 2 c clock i 2 c clock i 2 c data i 2 c data led state mode operating condition 1. off ac turn-off ac input is below minimum power-supply turn-on specification 2. green C blinking 1hz standby power supply standby output is operating within normal parameters and main output is disabled 3. green C solid power-good power supply standby & main outputs are operating within normal parameters and delivering power 4. yellow C blinking 1hz warning warning condition in power supply has been detected 5. yellow C solid fault fault condition in power supply has been detected. 3 see truth table below for operation . output connector and signal specification emissions and immunity characteristic standard compliance input current harmonics iec/en 61000-3-2 complies voltage fluctuation and flicker iec/en 61000-3-3 complies conducted emissions fcc 47 cfr part 15/cispr 22/en55022 class a, 6db margin esd immunity iec/en 61000-4-2 level 3 criteria a radiated field immunity iec/en 61000-4-3 level 3 criteria b electrical fast transient immunity iec/en 61000-4-4 level 3 criteria a surge immunity iec/en 61000-4-5 level 3 criteria a radiated field conducted immunity iec/en 61000-4-6 level 3 criteria a magnetic field immunity iec/en 61000-4-8 3 a/m criteria b voltage dips, interruptions iec/en 61000-4-11 230vin, 100% load, phase 0, dip 100% duration 10ms (a) 230vin, 50% load, phase 0, dip 100% duration 20ms (vsb:a, v1:a) 230vin, 100% load, phase 0, dip 100% duration > 20ms (vsb, v1:b) pin# function pin type description 14-26, 39-51 rtn power ground power and standby return 1-13, 52-64 12v power 12v output 37 12vsb power 12v standby output 38 psinterrupt output active low; interrupt line for power supply fault & warning detection as per pmbus spec 36 present# input power supply present signal (shortest pin) 35 psok analog output combination of there power supply output indicator signals: 1. ac input ok 2. power good 3. power supply fault 34 ishare analog i/o analog representation of main output current. typical analog voltage shall be 60.15mv/amp of main output current. 33 pson# input power supply on/off control signal 32 scl input smbus/pmbus clock 31 sda i/o smbus/pmbus data 30 gnd analog i/o power supply signal ground 29 n/a n/a reserved; no user connection 28 n/a n/a reserved; no user connection 27 addr analog input pmbus address power supply output card edge pcb top side pcb bottom side 1 64 33 32
d1u86p-w-1600-12-hbxdc series 86mm 1u front end ac-dc power supply d1u86p-w-1600-12-hbxdc.a01 page 4 of 6 www.murata-ps.com/support derating curves 0 20 40 60 80 100 120 140 25 30 35 40 45 50 55 main output current (adc) ? ambient temperature (c) ? 90v 120v 180v +? output current derating vs. ambient temperature (back to front air?ow) ? d1u86p \ w \ 1600 \ hb4dc; vsb 1.0a 12vdc @90vac \ 113a to 45c; derates to 90a at 50c main output current (adc) ambient temperature (c) 0 20 40 60 80 100 120 140 25 30 35 40 45 50 55 90v 120v 180v+ ? output current derating vs. ambient temperature (front to back air?ow) ? d1u86p \ w \ 1600 \ 12 \ hb3dc; vsb 2.5a (no derating) connector and signal specification 4 psok truth table vs. analog output dc_ok_h pwr_good_h ps_fault_l psok operation mode 0 0 1 < 0.1vdc vdd = 3.3vdc no dc input 0 1 1 (1/3) vdd invalid 1 0 1 (2/3) vdd standby 1 1 1 vdd power good x x 0 0.2-0.4vdc ps fault
d1u86p-w-1600-12-hbxdc series 86mm 1u front end ac-dc power supply d1u86p-w-1600-12-hbxdc.a01 page 5 of 6 www.murata-ps.com/support wiring diagram for output current sharing notes main output: current share is achieved using the droop method. nominal output voltage (12.20v) is achieved at 50% load and outp ut voltage droops at a rate of 3.10mv per amp increase. startup of parallel power supplies is not internally synchronized. if more than 1600w combined power i s needed, start-up synchroniza- tion must be provided by using a common ps_on signal. to account for 5% full load current sharing accuracy and the reduction i n full load output voltage due to droop, available output power must be derated by 10% when units are operated in parallel. standby output can be tied together for redundancy but total combined output power must not exceed 30w, internal mosfet oring d evices are used d1u86 d1u86 pson# pson# fet,bjt,wire or switch (debounced) to turn on 12v main output fet,bjt,wire or switch (debounced) to turn on 12v main output rtn rtn rtn rtn 14-26, 39-51 14-26, 39-51 1-13, 52-64 1-13, 52-64 12vsb 12vsb 37 37 33 33 main output load vsb load
d1u86p-w-1600-12-hbxdc series 86mm 1u front end ac-dc power supply d1u86p-w-1600-12-hbxdc.a01 page 6 of 6 www.murata-ps.com/support murata power solutions, inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. the descriptions contained her ein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. speci? cations are subject to cha nge without notice. ? 2015 murata power solutions, inc. murata power solutions, inc. 11 cabot boulevard, mans? eld, ma 02048-1151 u.s.a. iso 9001 and 14001 registered this product is subject to the following operating requirements and the life and safety critical application sales policy: refer to: http://www.murata-ps.com/requirements/ mechanical dimensions 3.4" x 7.78" x 1.59" [86.4mm x 197.7mm x 40.5mm] mating connector part number description fci 10053363-200lf right angle fci 10046971-001lf vertical optional accessories description part number 12v d1u86p output connector card d1u86p-12-conc application notes document number description acan-50 d1u86p output connector card acan-51 d1u86p communication protocol ac input connector: iec 320-c14 86.400.60 4.200.40 6.800.40 40.500.50 191.700.50 10.250.40 9.560.25 0.062" air flow direction front to back air flow direction back to front 2x3.200.25 83.520.30 240.75 ref 1.41 0.50 198.050.65 190.900.65 8.000.30 3.300.25 51.360.30 9.000.30 39.900.50 3.000.25 197.700.65 137.70 ref 16.500.30
|
