inductors april 2016 multilayer ferrite mlj1608 1608 [0603 inch]* * dimensions code jis[eia] inductors for power circuits mlj1608 ty p e mlj series
(2/8) inductors 20160411 / inductor_commercial_power_mlj1608_en.fm reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/8) inductors 20160411 / inductor_commercial_power_mlj1608_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. inductors for power circuits multilayer ferrite features the large current response by ferrite material of the new development. narrow tolerance response by lamination of high precision. significantly reduce high-frequency loss by adopting a low-loss material. application nfc circuit for smart phones and pcs, power supply lines for various electronic devices part number construction operating temperature range, pack age quantity, product weight the storage temperature range is for after the circuit board is mounted. product compatible with rohs directive halogen-free compatible with lead-free solders overview of mlj1608 type mlj 1608 w r16 t000 series name lwh dimensions characteristics inductance inductance tolerance packaging style internal code (mm) (h) 1608 1.60.80.8 w large current r16 160 j 5% t taping 000 r33 330 k 10% r56 560 type temperature range package quantity individual weight operating temperature c storage temperature c (pieces/reel) mg mlj1608 C55 to +125 C55 to +125 4,000 4 rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/8) inductors 20160411 / inductor_commercial_power_mlj1608_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlj1608 type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 30 to 60s 250 to 260c 10s max. natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/8) inductors 20160411 / inductor_commercial_power_mlj1608_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlj1608 type shape & dimensions recommended land pattern dimensions in mm 1.600.15 0.800.15 0.800.15 0.300.20 0.300.20 dimensions in mm 0.8 0.6 0.8 0.6
(6/8) inductors 20160411 / inductor_commercial_power_mlj1608_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlj1608 type electrical characteristics characteristics specification table the " " of the part number contains the inductance tolerance code, j (5%) or k (10%) measurement equipment ? equivalent measurement equipment may be used. l q l, q measuring conditions self-resonant frequency dc resistance rated current part no. frequency current idc-1 idc-1 idc-2 (nh) tolerance min. (mhz) (ma) (mhz)min. (mhz)typ. ( ) (ma)typ. (ma)max. (ma)max. 160 5%10% 25 25 1.0 330 450 0.1230% 750 600 700 mlj1608wr16 t000 220 5%10% 25 25 1.0 290 400 0.2030% 700 550 600 mlj1608wr22 t000 270 5%10% 25 25 1.0 260 350 0.2230% 650 550 550 mlj1608wr27 t000 330 5%10% 25 25 1.0 230 320 0.2430% 650 500 500 mlj1608wr33 t000 390 5%10% 25 25 1.0 210 290 0.2830% 600 450 450 mlj1608wr39 t000 470 5%10% 25 25 1.0 190 260 0.3830% 600 400 400 mlj1608wr47 t000 560 5%10% 25 25 1.0 170 230 0.4030% 550 400 400 mlj1608wr56 t000 measurement item product no. manufacturer l, q 4294a+16034g keysight technologies self-resonant frequency e4991a keysight technologies dc resistance type-7561 yokogawa
(7/8) inductors 20160411 / inductor_commercial_power_mlj1608_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlj1608 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. q frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. product no. manufacturer e4991a+16192a keysight technologies product no. manufacturer 4294a+16034g keysight technologies 1 10 100 1000 10 10000 1000 100 frequency ( mhz ) inductance ( nh ) wr56 wr47 wr39 wr33 wr27 wr22 wr16 0 10 20 30 40 50 60 q 1 10 1000 100 10000 frequency ( mhz ) wr56 wr47 wr39 wr33 wr27 wr22 wr16
(8/8) inductors 20160411 / inductor_commercial_power_mlj1608_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlj1608 type packaging style reel dimensions tape dimensions 1.0 ?180 2.0 2.0 0.5 ?13 0.2 ?21 0.8 ?60min. 14.4max. dimensions in mm 8.4 +2.0 C0.0 8.00.3 3.50.05 1.750.1 1.5 +0.1 C0.0 sprocket hole cavity a kb 160min. taping 200min. 300min. drawing direction 4.0 0.1 4.0 0.1 dimensions in mm ty p e a b k mlj1608 1.90.2 1.10.2 1.1 max.
|
