1 subminiature coaxial switch 1.35 mm high, dc to 11 ghz ms-156c series halogen free new 2010.11 features 1. low insertion loss 0.15 db typical at 2.5 ghz (not mated with the plug). 0.2 db typical at 6 ghz (not mated with the plug). 0.4 db typical at 11 ghz (not mated with the plug). 2. space-saving design 2.3 mm x 2.3 mm occupied board space. 3. low profile 1.35 mm protrusion above the board. 4. lightweight 0.014 g. total weight 5. durability 100 mating/unmating cycles, with corresponding plug. 6. performs over a wide frequency range applicable frequencies range over a wide band, from dc to 11 ghz. 7. board placement with automatic equipment packaged on tape-and-reel. also available with a vacuum pick-up cap over each switch. 8. halogen free chlorine, and bromine are not used in the receptacles. *definition according to iec 61249-2-21. br 900 ppm max., cl 900 ppm max., and br + cl 1500 ppm max. overview developed for inspection of high frequency circuits used in portable terminals.verification of the circuit performance is accomplished by simply inserting the external plug in the board mounted receptacle.this action re-directs the circuit from normal condition to the plug side. removing the plug restores circuit to its normal condition. ms-156c space-saving design low profile -1.35 mm protrusion above the board. lightweight -0.014 g. total weight. comparison with the existing MS-156HF footprint MS-156HF ms-156c height weight 2.7 2.3 2.7 2.3 1.6 1.35 27% saving of space 0.025g 0.014g 15% lower profile 44% lighter weight t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
2 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz specifications 100 ma max. 100 v dc 100 v ac / 1 minute frequency:10 to 55 hz, single amplitude of 0.75 mm, 2 hours in each of the 3 axis. acceleration of 490 m/s 2 , 6 ms duration, sine half- wave waveform, 3 cycles in each of the 3 axis temperature: -55? / +5? to +35? / +85? /+5? to +35? time: 30 / 5 max. / 30 / 5 max. (minutes) 50 cycles 96 hours at 85? 96 hours at -55? 96 hours at 402?, and humidity of 90 to 95% 100 cycles 100 m? max. 1000 m? min. no flashover or insulation breakdown contact resistance: 100 m? max. insulation resistance: 10 m? min. contact resistance: 100 m? max. insulation resistance: 10 m? min. contact resistance: 100 m? max. insulation resistance: 10 m? min. contact resistance: 100 m? max. insulation resistance: 10 m? min. contact resistance: 100 m? max. 1. contact resistance 2. insulation resistance 3. withstanding voltage 4. vibration 5. shock 6. temperature cycle 7. high temperature exposure 8. low temperature exposure 9. humidity 10. durability (mating/un-mating, with corresponding plug) item specification conditions operating temperature range rated power frequency range v.s.w.r. insertion loss isolation not mated with the plug -40? to +85? 2w dc to 11ghz 1.2 max. (dc to 2.5ghz) 1.3 max. (2.5ghz to 6.0ghz) 1.5 max. (6.0ghz to 11.0ghz) 0.15 db max. (dc to 2.5ghz) 0.2 db max. (2.5ghz to 6.0ghz) 0.4 db max. (6.0ghz to 11.0ghz) mated (ms-156-hrmj-3) -40? to +85? 2w dc to 8ghz 1.4 max. (dc to 3.0ghz) 1.8 max. (3.0ghz to 8.0ghz) 0.5 db max. (dc to 3.0ghz) 0.8 db max. (3.0ghz to 6.0ghz) 0.9 db max. (6.0ghz to 8.0ghz) 20 db min. (dc to 3.0ghz) 15 db min. (3.0ghz to 6.0ghz) 12 db min. (6.0ghz to 11.0ghz) shell insulator common terminal antenna terminal phosphor bronze 6t nylon cu-ni-si alloy phosphor bronze gold plated --------------------------- selective gold plated selective gold plated --------------------------- ul94hb --------------------------- --------------------------- part material finish remarks materials no electrical discontinuity of 1 s or more note 1: information contained in this catalog represents general requirements for this series. contact us for the drawings and specifications for a specific part number shown. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
3 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz typical data normally closed(n.c) normally open(n.o) isolation v.s.w.r. 01234567891011 [ghz] [ghz] [ghz] v.s.w.r. insertion loss [db] 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 insertion loss v.s.w.r. 012345678 v.s.w.r. insertion loss [db] 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 insertion loss 01234567891011 isolation 50 45 40 35 30 25 20 15 10 5 0 isolation t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
4 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz receptacle part number ms-156c ms-156c(20) cl no. 358-0251-2 358-0251-2-20 10,000 pieces/reel 2,000 pieces/reel packaging pcb mounting pattern and metal mask dimensions 2-0.5 2-1 2-1.8 1.3 1.6 2.4 0.4 0.4 2-0.9 0.5 0.5 2.5 2-2.4 1.9 0.3 0.3 1.7 0.48 0.48 1.44 c0.3 this area must be free of conductive traces and resist field. 1.16 2 pcb mounting pattern 0.1 thick metal mask dimensions * request drawing of the specific part for exact dimensions and tolerances. * specified dimensions must be followed to assure correct board placement and performance. ms-156c plug ms-156c g b g g c g a plug g b g g c g a not mated with the plug(n.c) mated with the plug(n.o) circuit diagram 2-(1.1) 0.35 0.35 2-0.6 2-0.6 2.3 ?1.92 1.35 0.6 c terminal a terminal 2.3 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
5 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz precautions recommended mounting of ms-156c coaxial switch on the pcb during the manufacturing process ms-156c to avoid contamination when cutting-off, do not place pcb bridge close to the mounted ms-156c. 1. this product is intended to be used for circuit inspection only. consult us if any other application is considered. 2. cross-hatched area shown on the pcb mounting pattern must be free of any conducive traces. placing conductive traces in this area may affect performance and will void product warranties. when the bottom surface of the product (i.e., the shaded area of the specified land dimensions diagram on the previous page) has been processed with a susbtrate copper trace and resist processing, hirose electric will not be able to warrant the product. 3. do not use hand soldering for mounting of ms-156c. doing so could result in solder and flux wicking to the contact areas. 4. exercise caution as not to allow any debris to enter the board mounted ms-156c when cutting pcb. 5. do not use the washing process. 6. please refrain from using the product in environments specifically affected by excessive vibration, shock, dust, high humidity, gases, very high temperatures and very low temperatures such as outdoor equipment. it might cause degradation or destruction of the product.even if it endures during a short time, long time quarification is not quaranteed. 7. for use of this product, be sure to put contact area of plug on position p(p4 full view) perpendicularly. 8. plugs can be roughly classified to two types. - for mass production line automatic check (press down type) - for manual check (with retentive lock) : unable to be used at production line. 9. when automatic inspections are to be performed during the manufacturing operations, request the ms- 156 plug connector manual for examples of implementation. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
6 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz recommended temperature profile q maximum temperature w peak temperature time e 230? min. r 220? min. t 180? to 200? metal mask thickness reflow cycles : 0.1 mm : 2 cycles : 260? : 10 sec. max. : 40 sec. max. : 60 sec. to 150 sec. : 60 sec. to 120 sec. using lead-free solder paste 10 sec.max. 260 temperature (?) 230 220 200 180 150 100 50 time (sec.) 60 sec. to 120 sec. 40 sec.max. 60 sec. to 150 sec. part number ms-156c ms-156c(20) reel size r = ?380mm r = ?180mm 10,000 pieces/reel 2,000 pieces/reel packaging 1.75 5.5 12 (1.95) e ?13 ?r 2 44 d 12.4 ?1.5 unreeling direction unreeling direction c terminal a terminal a terminal c terminal d e ?50 max. packaging specifications ms-156c reel dimentions t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
7 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz plugs press down, right angle ?3.2 20.9 ?4 ?6 4-c1 11.15 2.9 m8 part number applicable cable: 1.5d-hqew, 1.5d-qew (fujikura ltd.) cl no. durability 358-0173-0 ms-156-c lp -1 10,000 times simplified lock, right angle, short ?6.5 8.1 3.2 4.27 5.8 15 1.3 ?2.5 ?3 ?3.6 part number applicable cable: dfs111-ul1979(junkosha ltd.) please contact hirose sales representative for cable length and cable end treatment. applicable cable: dfs111-ul1979(junkosha ltd.) please contact hirose sales representative for cable length and cable end treatment. applicable cable: khcx-32awg-sb-ta(showa electric wire & cable co., ltd.) please contact hirose sales representative for cable length and cable end treatment. cl no. durability 358-0268-5 ms-156-088lp-h1 500 times simplified lock, right angle, long ?6.5 14.9 10 21.8 1.6 4.27 5.8 ?3.6 ?3 ?2.5 part number cl no. durability 358-0275-0 ms-156-088lp-h2 500 times simplified lock, right angle, for antenna ?1.13 6.1 2.5 3 part number cl no. durability 358-0276-3 ms-156c-lp-068 30 times t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
8 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz simplified lock ?8.5 8 21.98 5.9 8.18 1.6 ?3.6 ?0.5 3 1/4-36uns-2a part number cl no. durability 358-0290-4 ms-156-hrmj-h1 500 times 1/4-36uns-2a 18.63 8.12 8 28.13 ?20 14 ?3.4 ?5 1 2?2.6 part number cl no. durability 358-0171-5 ms-156-hrmj-3 10,000 times press down, with flange, long 8 33.01 13 23.51 ?3.4 ?5 2?2.6 14 1/4-36uns-2a 1 ?20 part number cl no. durability 358-0198-1 ms-156-hrmj-14 10,000 times press down, with flange, short press down, with flange, right angle ?5.4 ?3.4 7.73 18.63 29.23 10.6 1 1/4-36uns-2a 2?2.6 ?20 7.9 14 8 ?7.9 part number cl no. durability 358-0289-5 ms-156lp-hrmj-8 100,000 times sma conversion adapters t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
9 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz floating (self-pressing) 13 ?3.8 11.75 28.24 2.5 38.6 20 1/4-36uns-2a 1.45 ?5.4 ?10.3 ?24 2?2.6 part number cl no. durability 358-0194-0 ms-156-hrmj-10 10,000 times 12 ?4.3 ?5.9 ?10.3 11.75 29.49 2.5 39.85 3.75 20 1/4-36uns-2a ?24 2?2.6 part number cl no. durability 358-0196-6 ms-156-hrmj-12 10,000 times floating (self-pressing) ?12 17 20 ?5.4 ?3.4 2?2.6 2?2.1 12 8 3.3 2.5 11.2 28.24 38.6 ?24 floating (self-pressing) part number cl no. durability 358-0295-8 ms-156-hrmj-29 200,000 times t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
10 ms-156c seriessubminiature coaxial switch 1.35 mm high, dc to 11 ghz sma conversion adapter ?2 ?6 8.3 ?9 3 6.3 16.05 0.75 1/4-36uns-2a part number cl no. durability 358-0188-8 ms-156r-hrmj-1 500 times n conversion adapter 0.75 13.21 2.54 41.9 14.3 5/8-24nef-2a ?2 ?5.45 ?22 part number cl no. durability 358-0176-9 ms-156r-nj-1 500 times adapter for plug inspection t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
|
