Part Number Hot Search : 
1N476 A1791N WFF2N60B LV2102A H8S2110B AN942 R65F12Q SZ5211
Product Description
Full Text Search
 

To Download LT3800-15 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  lt3800 1 3800fc typical application features applications description high-voltage synchronous current mode step-down controller the lt ? 3800 is a 200khz ? xed frequency high voltage synchronous current mode step-down switching regulator controller. the ic drives standard gate n-channel power mosfets and can operate with input voltages from 4v to 60v. an onboard regulator provides ic power directly from v in and provides for output-derived power to minimize v in quiescent current. mosfet drivers employ an internal dynamic bootstrap feature, maximizing gate-source on voltages during normal operation for improved operating ef? ciencies. the lt3800 incorporates burst mode ? opera- tion, which reduces no load quiescent current to under 100a. light load ef? ciencies are also improved through a reverse inductor current inhibit, allowing the controller to support discontinuous operation. both burst mode operation and the reverse-current inhibit features can be disabled if desired. the lt3800 incorporates a program- mable soft-start that directly controls the voltage slew rate of the converter output for reduced startup surge currents and overshoot errors. the lt3800 is available in a 16-lead thermally enhanced tssop package. 12v 75w dc/dc converter with reverse current inhibit and input uvlo n wide 4v to 60v input voltage range n output voltages up to 36v n adaptive nonoverlap circuitry prevents switch shoot-through n reverse inductor current inhibit for discontinuous operation improves ef? ciency with light loads n output slew rate controlled soft-start with auto-reset n 100a no load quiescent current n low 10a current shutdown n 1% regulation accuracy n 200khz operating frequency n standard gate n-channel power mosfets n current limit unaffected by duty cycle n reverse overcurrent protection n 16-lead thermally enhanced tssop package n 12v and 42v automotive and heavy equipment n 48v telecom power supplies n avionics and industrial control systems n distributed power converters ef? ciency and power loss v in shdn c ss burst_en v fb v c sense C boost tg sw v cc bg pgnd sense + lt3800 sgnd 1.5nf 200k 100pf 680pf 174k 1% 20k 1% 82.5k 1m 82.5k 0.015 bas19 1n4148 1f 1f 1f 3 56f 2 + 10f 270f + si7850dp si7370dp b160 15h v in 20v to 55v v out 12v at 75w 3800 ta01a i load (a) efficiency (%) power loss (w) 100 95 90 3800 ta01b 70 75 85 80 6 5 4 0 1 3 2 10 0.1 1 v in = 24v loss (48v) v in = 48v v in = 60v v in = 36v l , lt, ltc, ltm, linear technology, burst mode and the linear logo are registered trademarks and no r sense and thinsot are trademarks of linear technology corporation. all other trademarks are the property of their respective owners. protected by u.s. patents including 5481178, 6611131, 6304066, 6498466, 6580258.
lt3800 2 3800fc pin configuration absolute maximum ratings supply voltages input supply pin (v in ) ............................... C0.3v to 65v boosted supply pin (boost) .................... C0.3v to 80v boosted supply voltage (b oost C sw) ... C0.3v to 24v boosted supply reference pin (sw) ............ C2v to 65v local supply pin (v cc ) .............................. C0.3v to 24v input voltages sense + , sense C ...................................... C0.3v to 40v sense + C sense C ......................................... C1v to 1v burst_en pin .......................................... C0.3v to 24v other inputs ( shdn , c ss , v fb , v c ) .......... C0.3v to 5.0v input currents shdn , c ss ............................................... C1ma to 1ma maximum temperatures operating junction temperature range (note 2) lt3800e (note 3) .............................. C40c to 125c lt3800i ............................................. C40c to 125c storage temperature range .................. C65c to 150c lead temperature (soldering, 10 sec) ................. 300c (note 1) fe package 16-lead plastic tssop 1 2 3 4 5 6 7 8 top view 16 15 14 13 12 11 10 9 v in nc shdn c ss burst_en v fb v c sense C boost tg sw nc v cc bg pgnd sense + 17 t jmax = 125c, ja = 40c/w, jc = 10c/w exposed pad (pin 17) is sgnd must be soldered to pcb order information lead free finish tape and reel part marking package description temperature range lt3800efe#pbf lt3800efe#trpbf 3800efe 16-lead plastic tssop C40c to 125c lt3800ife#pbf lt3800ife#trpbf 3800ife 16-lead plastic tssop C40c to 125c consult ltc marketing for parts speci? ed with wider operating temperature ranges. consult ltc marketing for information on non-standard lead based ? nish parts. for more information on lead free part marking, go to: http://www.linear.com/leadfree/ for more information on tape and reel speci? cations, go to: http://www.linear.com/tapeandreel/ electrical characteristics symbol parameter conditions min typ max units v in operating voltage range (note 4) minimum start voltage uvlo threshold (falling) uvlo hysteresis 4 7.5 3.65 3.80 670 60 3.95 v v v mv i vin v in supply current v in burst mode current v in shutdown current v cc > 9v v burst_en = 0v, v fb = 1.35v v shdn = 0v 20 20 815 a a a v boost operating voltage operating voltage range (note 5) uvlo threshold (rising) uvlo hysteresis v boost C v sw v boost C v sw v boost C v sw 5 0.4 75 20 v v v v the l denotes the speci? cations which apply over the full operating temperature range, otherwise speci? cations are at t a = 25c. v in = 20v, v cc = boost = burst_en = 10v, shdn = 2v, sense C = sense + = 10v, sgnd = pgnd = sw = 0v, ctg = cbg = 3300pf, unless otherwise noted.
lt3800 3 3800fc electrical characteristics the l denotes the speci? cations which apply over the full operating temperature range, otherwise speci? cations are at t a = 25c. v in = 20v, v cc = boost = burst_en = 10v, shdn = 2v, sense C = sense + = 10v, sgnd = pgnd = sw = 0v, ctg = cbg = 3300pf, unless otherwise noted. symbol parameter conditions min typ max units i boost boost supply current (note 6) boost burst mode current boost shutdown current v burst_en = 0v v shdn = 0v 1.4 0.1 0.1 ma a a v cc operating voltage (note 5) output voltage uvlo threshold (rising) uvlo hysteresis 8.0 6.25 500 20 8.3 v v v mv i vcc v cc supply current (note 6) v cc burst mode current v cc shutdown current short-circuit current v burst_en = 0v v shdn = 0v C40 3 80 20 C120 3.6 ma a a ma v shdn enable threshold (rising) threshold hysteresis 1.30 1.35 120 1.40 v mv v sense common mode range current limit sense voltage reverse protect sense voltage reverse current offset v sense + C v sense C v sense + C v sense C , v burst_en = v cc v burst_en = 0v or v burst_en = v fb 0 140 150 C150 10 36 175 mv mv mv i sense input current (i sense + + i sense C ) v sense(cm) = 0v v sense(cm) = 2.75v v sense(cm) > 4v 0.8 C20 C0.3 ma a ma f o operating frequency 190 175 200 210 220 khz khz v fb error amp reference voltage measured at v fb pin 1.224 1.215 1.231 1.238 1.245 v v i fb feedback input current 25 na v fb(ss) soft-start disable voltage soft-start disable hysteresis v fb rising 1.185 300 v mv i css soft-start capacitor control current 2 a g m error amp transconductance 275 350 400 mhos a v error amp dc voltage gain 62 db v c error amp output range zero current to current limit 1.2 v i vc error amp sink/source current 30 a v tg,bg gate drive output on voltage (note 7) gate drive output off voltage 9.8 0.1 v v t tg,bg gate drive rise/fall time 10% to 90% or 90% to 10% 50 ns t tg(off) minimum off time 450 ns t tg(on) minimum on time 300 500 ns t nol gate drive nonoverlap time tg fall to bg rise bg fall to tg rise 200 150 ns ns
lt3800 4 3800fc electrical characteristics shutdown threshold (rising) vs temperature shutdown threshold (falling) vs temperature v cc vs temperature v cc vs i cc(load) v cc vs v in i cc current limit vs temperature note 1: stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. exposure to any absolute maximum rating condition for extended periods may affect device reliability and lifetime. note 2: this ic includes overtemperature protection that is intended to protect the device during momentary overload conditions. junction temperature will exceed 125c when overtemperature protection is active. continuous operation above the speci? ed maximum operating junction temperature may impair device reliability. note 3: the lt3800e is guaranteed to meet performance speci? cations from 0c to 125c junction temperature. speci? cations over the C40c to 125c operating junction temperature range are assured by design, characterization and correlation with statistical process controls. the typical performance characteristics lt3800i is guaranteed over the full C40c to 125c operating junction temperature range. note 4: v in voltages below the start-up threshold (7.5v) are only supported when v cc is externally driven above 6.5v. note 5: operating range dictated by mosfet absolute maximum gate- source voltage ratings. note 6: supply current speci? cation does not include switch drive currents. actual supply currents will be higher. note 7: dc measurement of gate drive output on voltage is typically 8.6v. internal dynamic bootstrap operation yields typical gate on voltages of 9.8v during standard switching operation. standard operation gate on voltage is not tested but guaranteed by design. temperature (c) C50 C25 1.37 1.36 1.35 1.34 1.33 100 3800 g01 0 50 125 25 75 shutdown threshold, rising (v) C50 C25 100 0 50 125 25 75 temperature (c) 1.240 1.235 1.230 1.225 1.220 3800 g02 shutdown threshold, falling (v) temperature (c) C50 C25 v cc (v) 8.0 8.1 7.8 7.9 125 3800 g03 0 50 25 75 100 i cc = 0ma i cc = 20ma i cc(load) (ma) 0 v cc (v) 40 3800 g04 10 20 30 8.05 8.00 7.95 7.90 7.85 51525 35 t a = 25c v in (v) 4 v cc (v) 8 7 6 5 4 3 79 12 3800 g05 56 8 10 11 i cc = 20ma t a = 25c C50 C25 100 0 50 125 25 75 temperature (c) 200 175 150 125 100 75 50 3800 g06 i cc current limit (ma)
lt3800 5 3800fc typical performance characteristics v cc uvlo threshold (rising) vs temperature i cc vs v cc ( shdn = 0v) error amp transconductance vs temperature i (sense + + sense C ) vs v sense(cm) operating frequency vs temperature error amp reference vs temperature pin functions temperature (c) C50 C25 100 3800 g07 0 50 125 25 75 6.30 6.25 6.20 6.15 v cc uvlo threshold, rising (v) v cc (v) 0 i cc (a) 15 20 25 16 3800 g12 10 5 0 246 810 12 14 18 20 t a = 25c temperature (c) C50 C25 100 0 50 125 25 75 380 360 340 320 3800 g08 error amp transconductance (mho) v sense(cm) (v) 0 0.5 1.5 2.5 3.5 4.5 i (sense + + sense C ) (a) 800 600 400 200 0 C200 C400 1.0 2.0 3.0 4.0 3800 g09 5.0 t a = 25c temperature (c) 3800 g10 C50 220 210 200 190 180 C25 operating frequency (khz) 100 0 50 125 25 75 C50 C25 100 0 50 125 25 75 temperature (c) error amp reference (v) 1.232 1.231 1.230 1.229 1.228 1.227 3800 g11 v in (pin 1): converter input supply. nc (pin 2): no connection. shdn (pin 3): precision shutdown pin. enable threshold is 1.35v (rising) with 120mv of input hysteresis. when in shutdown mode, all internal ic functions are disabled. the precision threshold allows use of the shdn pin to incorporate uvlo functions. if the shdn pin is pulled below 0.7v, the ic enters a low current shutdown mode with i vin < 10a. in low-current shutdown, the ic will sink 20a from the v cc pin until that local supply has collapsed. typical pin input bias current is <10na and the pin is internally clamped to 6v. c ss (pin 4): soft-start ac coupling capacitor input. connect capacitor (c ss ) in series with a 200k resistor from pin to converter output (v out ). controls converter start-up output voltage slew rate ( ? v out / ? t). slew rate corresponds to 2a average current through the soft-start coupling capacitor. the capacitor value for a desired output startup slew rate follows the relation: c ss = 2a/( ? v out / ? t) shorting this pin to sgnd disables the soft-start function burst_en (pin 5): burst mode operation enable pin. this pin also controls reverse-inhibit mode of operation. when the pin voltage is below 0.5v, burst mode operation
lt3800 6 3800fc pin functions and reverse-current inhibit functions are enabled. when the pin voltage is above 0.5v, burst mode operation is dis- abled, but reverse-current inhibit operation is maintained. dc/dc converters operating with reverse-current inhibit operation (burst_en = v fb ) have a 1ma minimum load requirement. reverse-current inhibit is disabled when the pin voltage is above 2.5v. this pin is typically shorted to ground to enable burst mode operation and reverse-current inhibit, shorted to v fb to disable burst mode operation while enabling reverse-current inhibit, and connected to v cc pin to disable both functions. see applications information section. v fb (pin 6): error ampli? er inverting input. the noninvert- ing input of the error ampli? er is connected to an internal 1.231v reference. desired converter output voltage (v out ) is programmed by connecting a resistive divider from the converter output to the v fb pin. values for the resistor connected from v out to v fb (r2) and the resistor con- nected from v fb to ground (r1) can be calculated via the following relationship: r2 = r1? v out 1.231 C1       the v fb pin input bias current is 25na, so use of extremely high value feedback resistors could cause a converter output that is slightly higher than expected. bias current error at the output can be estimated as: ? v out(bias) = 25na ? r2 v c (pin 7): error ampli? er output. the voltage on the v c pin corresponds to the maximum (peak) switch current per oscillator cycle. the error ampli? er is typically con? gured as an integrator by connecting an rc network from this pin to ground. this network creates the dominant pole for the converter voltage regulation feedback loop. speci? c integrator characteristics can be con? gured to optimize transient response. connecting a 100pf or greater high frequency bypass capacitor from this pin to ground is also recommended. when burst mode operation is enabled (see pin 5 description), an internal low impedance clamp on the v c pin is set at 100mv below the burst threshold, which limits the negative excursion of the pin voltage. there- fore, this pin cannot be pulled low with a low-impedance source. if the v c pin must be externally manipulated, do so through a 1k series resistance. sense C (pin 8): negative input for current sense ampli- ? er. sensed inductor current limit set at 150mv across sense inputs. sense + (pin 9): positive input for current sense ampli- ? er. sensed inductor current limit set at 150mv across sense inputs. pgnd (pin 10): high current ground reference for syn- chronous switch. current path from pin to negative terminal of v cc decoupling capacitor must not corrupt sgnd. bg (pin 11): synchronous switch gate drive output. v cc (pin 12): internal regulator output. most ic func- tions are powered from this pin. driving this pin from an external source reduces v in pin current to 20a. this pin is decoupled with a low esr 1f capacitor to pgnd. in shutdown mode, this pin sinks 20a until the pin voltage is discharged to 0v. see typical performance characteristics. nc (pin 13): no connection. sw (pin 14): reference for v boost supply and high cur- rent return for bootstrapped switch. tg (pin 15): bootstrapped switch gate drive output. boost (pin 16): bootstrapped supply C maximum operat- ing voltage (ground referred) to 75v. this pin is decoupled with a low esr 1f capacitor to pin sw. the voltage on the decoupling capacitor is refreshed through a recti? er from either v cc or an external source. exposed package backside (sgnd) (pin 17): low noise ground reference. sgnd connection is made through the exposed lead frame on back of tssop package which must be soldered to the pcb ground.
lt3800 7 3800fc functional diagram C + C + C + C + C + v in uvlo (<4v) bst uvlo 8v reg feedback reference C + 1.231v 3.8v reg internal supply rail 1 16 15 14 12 10 9 17 3 5 7 4 6 v in v cc uvlo (<6v) shdn drive control drive control nol switch logic drive control burst_en v c c ss sense C v fb C + 1.185v 1v 0.5v error amp 2a burst mode operation 8 soft-start disable/burst enable r s q oscillator slope comp generator boost tg sw v cc 11 bg pgnd sense + gnd 3800 fd boosted switch driver current sense comparator g m C+ r s q C + 160mv synchronous switch driver reverse current inhibit 10mv C +
lt3800 8 3800fc overview the lt3800 is a high input voltage range step-down synchronous dc/dc converter controller ic that uses a 200khz constant frequency, current mode architecture with external n-channel mosfet switches. the lt3800 has provisions for high ef? ciency, low load operation for battery-powered applications. burst mode operation reduces total average input quiescent currents to 100a during no load conditions. a low current shutdown mode can also be activated, reducing quiescent current to <10a. burst mode operation can be disabled if desired. the lt3800 also employs a reverse-current inhibit feature, allowing increased ef? ciencies during light loads through nonsynchronous operation. this feature disables the synchronous switch if inductor current approaches zero. if full time synchronous operation is desired, this feature can be disabled. much of the lt3800s internal circuitry is biased from an internal linear regulator. the output of this regulator is the v cc pin, allowing bypassing of the internal regulator. the associated internal circuitry can be powered from the output of the converter, increasing overall converter ef? ciency. using externally derived power also eliminates the ics power dissipation associated with the internal v in to v cc regulator. theory of operation (see block diagram) the lt3800 senses converter output voltage via the v fb pin. the difference between the voltage on this pin and an internal 1.231v reference is ampli? ed to generate an error voltage on the v c pin which is, in turn, used as a threshold for the current sense comparator. during normal operation, the lt3800 internal oscilla- tor runs at 200khz. at the beginning of each oscillator cycle, the switch drive is enabled. the switch drive stays enabled until the sensed switch current exceeds the v c derived threshold for the current sense comparator and, in turn, disables the switch driver. if the current comparator threshold is not obtained for the entire oscillator cycle, the switch driver is disabled at the end of the cycle for 450ns. this minimum off-time mode of operation assures regeneration of the boost bootstrapped supply. power requirements the lt3800 is biased using a local linear regulator to generate internal operational voltages from the v in pin. virtually all of the circuitry in the lt3800 is biased via an internal linear regulator output (v cc ). this pin is decoupled with a low esr 1f capacitor to pgnd. the v cc regulator generates an 8v output provided there is ample voltage on the v in pin. the v cc regulator has approximately 1v of dropout, and will follow the v in pin with voltages below the dropout threshold. the lt3800 has a start-up requirement of v in > 7.5v. this assures that the onboard regulator has ample headroom to bring the v cc pin above its uvlo threshold. the v cc regulator can only source current, so forcing the v cc pin above its 8v regulated voltage allows use of externally derived power for the ic, minimizing power dissipation in the ic. using the onboard regulator for start-up, then deriving power for v cc from the converter output maxi- mizes conversion ef? ciencies and is common practice. if v cc is maintained above 6.5v using an external source, the lt3800 can continue to operate with v in as low as 4v. the lt3800 operates with 3ma quiescent current from the v cc supply. this current is a fraction of the actual v cc quiescent currents during normal operation. additional current is produced from the mosfet switching currents for both the boosted and synchronous switches and are typically derived from the v cc supply. because the lt3800 uses a linear regulator to generate v cc , power dissipation can become a concern with high v in voltages. gate drive currents are typically in the range of 5ma to 15ma per mosfet, so gate drive currents can create substantial power dissipation. it is advisable to derive v cc and v boost power from an external source whenever possible. applications information
lt3800 9 3800fc applications information figure 1. v cc regulator continuous operating conditions the onboard v cc regulator will provide gate drive power for start-up under all conditions with total mosfet gate charge loads up to 180nc. the regulator can operate the lt3800 continuously, provided the v in voltage and/or mosfet gate charge currents do not create excessive power dissipation in the ic. safe operating conditions for continuous regulator use are shown in figure 1. in applications where these conditions are exceeded, v cc must be derived from an external source after start-up. in lt3800 converter applications with output voltages in the 9v to 20v range, back-feeding v cc and v boost from the converter output is trivial, accomplished by connect- ing diodes from the output to these supply pins. deriving these supplies from output voltages greater than 20v will require additional regulation to reduce the feedback voltage. outputs lower than 9v will require step-up techniques to increase the feedback voltage to something greater than the 8v v cc regulated output. low power boost switchers are sometimes used to provide the step-up function, but a simple charge-pump can perform this function in many instances. charge pump doubler total fet gate charge (nc) 0 10 v in (v) 20 30 40 50 60 70 50 100 150 200 3800 f01 safe operating conditions charge pump tripler v out 1f b0520 b0520 1f si1555dl lt3800 v cc bg v out 1f b0520 b0520 1f 1f si1555dl si1555dl lt3800 v cc bg b0520 3800 ai01 inductor auxiliary winding tg v out 3800 ai04 v cc sw bg n ? ? lt3800
lt3800 10 3800fc applications information burst mode the lt3800 employs low current burst mode functional- ity to maximize ef? ciency during no load and low load conditions. burst mode operation is enabled by shorting the burst_en pin to sgnd. burst mode operation can be disabled by shorting burst_en to either v fb or v cc . when the required switch current, sensed via the v c pin voltage, is below 15% of maximum, the burst mode operation is employed and that level of sense current is latched onto the ic control path. if the output load requires less than this latched current level, the converter will overdrive the output slightly during each switch cycle. this overdrive condition is sensed internally and forces the voltage on the v c pin to continue to drop. when the voltage on v c drops 150mv below the 15% load level, switching is disabled and the lt3800 shuts down most of its internal circuitry, reducing total quiescent current to 100a. when the converter output begins to fall, the v c pin voltage begins to climb. when the voltage on the v c pin climbs back to the 15% load level, the ic returns to normal operation and switching resumes. an internal clamp on the v c pin is set at 100mv below the switch disable threshold, which limits the negative excursion of the pin voltage, minimizing the converter output ripple during burst mode operation. during burst mode operation, v in pin current is 20a and v cc current is reduced to 80a. if no external drive is provided for v cc , all v cc bias currents originate from the v in pin, giving a total v in current of 100a. burst current can be reduced further when v cc is driven using an output derived source, as the v cc component of v in current is then reduced by the converter buck ratio. reverse-current inhibit the lt3800 contains a reverse-current inhibit feature to maximize ef? ciency during light load conditions. this mode of operation allows discontinuous operation, and is sometimes referred to as pulse-skipping mode. refer to figure 2. this feature is enabled with burst mode operation, and can also be enabled while burst mode operation is disabled by shorting the burst_en pin to v fb . when reverse-current inhibit is enabled, the lt3800 sense ampli? er detects inductor currents approaching zero and disables the synchronous switch for the remainder of the switch cycle. if the inductor current is allowed to go negative before the synchronous switch is disabled, the switch node could inductively kick positive with a high dv/dt. the lt3800 prevents this by incorporating a 10mv positive offset at the sense inputs. figure 2. inductor current vs mode pulse skip mode i l i l forced continuous decreasing load current 3800 f02
lt3800 11 3800fc applications information with the reverse-current inhibit feature enabled, an lt3800 converter will operate much like a nonsynchronous converter during light loads. reverse-current inhibit reduces resistive losses associated with inductor ripple currents, which improves operating ef? ciencies during light-load conditions. an lt3800 dc/dc converter that is operating in reverse- inhibit mode has a minimum load requirement of 1ma (burst_en = v fb ). since most applications use output- generated power for the lt3800, this requirement is met by the bias currents of the ic, however, for applications that do not derive power from the output, this require- ment is easily accomplished by using a 1.2k resistor connected from v fb to ground as one of the converter output voltage programming resistors (r1). there are no minimum load restrictions when in burst mode operation (burst_en < 0.5v) or continuous conduction mode (burst_en > 2.5v). soft-start the lt3800 incorporates a programmable soft-start function to control start-up surge currents, limit output overshoot and for use in supply sequencing. the soft-start function directly monitors and controls output voltage slew rate during converter start-up. as the output voltage of the converter rises, the soft-start circuit monitors v/ t current through a coupling capaci- tor and adjusts the voltage on the v c pin to maintain an average value of 2a. the soft-start function forces the programmed slew rate while the converter output rises to 95% regulation, which corresponds to 1.185v on the v fb pin. once 95% regulation is achieved, the soft-start circuit is disabled. the soft-start circuit will re-enable when the v fb pin drops below 70% regulation, which corresponds to 300mv of control hysteresis on the v fb pin, which allows for a controlled recovery from a brown-out condition. the desired soft-start rise time (t ss ) is programmed via a programming capacitor c ss1 , using a value that cor- responds to 2a average current during the soft-start interval. this capacitor value follows the relation: c ss1 = 2e C6 ?t ss v out r ss tcll et to 200 fo ot lcton. considerations for low voltage output applications the lt3800 c ss pin biases to 220mv during the soft-start cycle, and this voltage is increased at network node a by the 2a signal current through r ss , so the output has to reach this value before the soft-start function is engaged. the value of this output soft-start start-up voltage offset (v out(ss) ) follows the relation: v out(ss) = 220mv + r ss ? 2e C6 which is typically 0.64v for r ss = 200k. in some low voltage output applications, it may be desir- able to reduce the value of this soft-start start-up voltage offset. this is possible by reducing the value of r ss . with reduced values of r ss , the signal component caused by voltage ripple on the output must be minimized for proper soft-start operation. peak-to-peak output voltage ripple ( ? v out ) will be imposed on node a through the capacitor c ss1 . the value of r ss can be set using the following equation: r ss =  v out 1.3e C6 it otnt to e lo esr ott ccto fo lt300 olte conete den to ne t le olte coonent. a den t n excee le coonent cn e edenced oen te v c n dn te tt ccle. c ss v out c ss1 r ss a 300 ai06 lt300
lt3800 12 3800fc applications information the soft-start cycle should be evaluated to verify that the reduced r ss value allows operation without excessive modulation of the v c pin before ? nalizing the design. if the v c pin has an excessive ripple component during the soft-start cycle, converter output ripple should be reduced or r ss increased. reduction in converter output ripple is typically accomplished by increasing output capacitance and/or reducing output capacitor esr. external current limit foldback circuit an additional start-up voltage offset can occur during the period before the lt3800 soft-start circuit becomes active. before the soft-start circuit throttles back the v c pin in response to the rising output voltage, current as high as the peak programmed current limit (i max ) can ? ow in the inductor. switching will stop once the soft-start circuit takes hold and reduces the voltage on the v c pin, but the output voltage will continue to increase as the stored energy in the inductor is transferred to the output capacitor. with i max ? owing in the inductor, the resulting leading-edge rise on v out due to energy stored in the inductor follows the relationship:  v out = i max ? l c out       1/ 2 indcto cent tcll doent ec i max n te fe ccle tt occ efoe oft-tt ecoe cte t cn t nt olte o ll ndcto o te oe elton efl ot-ce ceno. t ene tnfe ncee n ott olte tcll ll t fo oe lo olte lcton t eltel ll ott ccto t cn ecoe n cnt. te olt- e e cn e edced ncen ott cctnce c t ddtonl ltton on c out fo tee lo olte le. anote oc to dd n extenl cent lt foldc cct c edce te le of i max dn tt-. an extenl cent lt foldc cct cn e el ncooted nto n lt300 dc/dc conete lcton lcn 1n1 dode nd eto fo te conete ott (v out ) to te lt300 v c n. t lt te e cent to 0.25 ? i max en v out 0v. a cent lt foldc cct lo te dded dnte of odn edced ott cent n te dc/dc conete dn ot-cct flt condton o foldc cct e efl een f te oft-tt fncton dled. if te oft-tt cct dled otn te c ss n to ond te extenl cent lt fold-c cct t e od ed ddn n ddtonl dode nd eto. te 2-dode 2-eto neto on lo ode 0.25 ? i max en v out 0v. soft-start characteristic showing excessive ripple component desirable soft-start characteristic v out v out(ss) v(v c ) 250s/div 3800 ai07 v out v out(ss) v(v c ) 250s/div 3800 ai08
lt3800 13 3800fc applications information adaptive nonoverlap (nol) output stage the fet driver output stages implement adaptive nonover- lap control. this feature maintains a constant dead time, preventing shoot-through switch currents, independent of the type, size or operating conditions of the external switch elements. each of the two switch drivers contains a nol control circuit, which monitors the output gate drive signal of the other switch driver. the nol control circuits interrupt the turn on command to their associated switch driver until the other switch gate is fully discharged. antislope compensation most current mode switching controllers use slope com- pensation to prevent current mode instability. the lt3800 is no exception. a slope-compensation circuit imposes an arti? cial ramp on the sensed current to increase the rising slope as duty cycle increases. unfortunately, this additional ramp corrupts the sensed current value, reducing the achievable current limit value by the same amount as the added ramp represents. as such, current limit is typically reduced as duty cycles increase. the lt3800 contains circuitry to eliminate the current limit reduction typically associated with slope compensation. as the slope-com- pensation ramp is added to the sensed current, a similar ramp is added to the current limit threshold reference. the end result is that current limit is not compromised, so a lt3800 converter can provide full power regardless of required duty cycle. shutdown the lt3800 shdn pin uses a bandgap generated reference threshold of 1.35v. this precision threshold allows use of the shdn pin for both logic-level controlled applications and analog monitoring applications such as power supply sequencing. the lt3800 operational status is primarily controlled by a uvlo circuit on the v cc regulator pin. when the ic is enabled via the shdn pin, only the v cc regulator is enabled. switching remains disabled until the uvlo threshold is achieved at the v cc pin, when the remainder of the ic is enabled and switching commences. because an lt3800 controlled converter is a power transfer device, a voltage that is lower than expected on the input supply could require currents that exceed the sourcing capabilities of that supply, causing the system to lock up in an undervoltage state. input supply start-up protection can be achieved by enabling the shdn pin using a resistive divider from the v in supply to ground. setting the divider output to 1.35v when that supply is at an adequate voltage prevents an lt3800 converter from drawing large currents until the input supply is able to provide the required power. 120mv of input hysteresis on the shdn pin allows for almost 10% of input supply droop before disabling the converter. current limit foldback circuit for applications that use soft-start alternative current limit foldback circuit for applications that have soft-start disabled v c v out 1n4148 3800 ai09 47k v c v out 1n4148 1n4148 3800 ai10 39k 27k
lt3800 14 3800fc applications information the uvlo voltage, v in(uvlo) , is set using the following relation: r a = r b ? v in(uvlo) C 1.35v 1.35v if ddtonl tee deed fo te enle fncton n extenl ote feedc eto cn e ed fo te lt300 elto ott. te tdon fncton cn e dled connectn te shdn pin to v in through a large value pull-up resistor. this pin contains a low impedance clamp at 6v, so the shdn pin will sink current from the pull-up resistor (r pu ): i shdn = v in C6v r pu bece t neent ll ll te shdn pin to the 6v clamp voltage, it will violate the 5v absolute maximum voltage rating of the pin. this is permitted, however, as long as the absolute maximum input current rating of 1ma is not exceeded. input shdn pin currents of <100a are recommended; a 1m or greater pull-up resistor is typically used for this con? guration. inductor selection the primary criterion for inductor value selection in lt3800 applications is ripple current created in that inductor. basic design considerations for ripple current are output voltage ripple, and the ability of the internal slope compensation waveform to prevent current mode instability. once the value is determined, an inductor must also have a satu- ration current equal to or exceeding the maximum peak current in the inductor. ripple current ( ? i l ) in an inductor for a given value (l) can be approximated using the relation:  i l = 1C v out v in       ? v out f o ?l te tcl ne of le fo ? i is 20% to 40% of i out(max) , where i out(max) is the maximum converter output load current. ripple currents in this range typically yield a good design compromise between inductor perfor- mance versus inductor size and cost, and values in this range are generally a good starting point. a starting point inductor value can thus be determined using the relation: l = v out ? 1C v out v in       f o ? 0.3 ?i out(max) ue of lle ndcto ncee ott le cent en oe cctnce on te conete ott. alo t conete oeton t dt ccle ete tn 50 te loe coenton cteon deced lte t e et. denn fo lle le cent ee le ndcto le c cn ncee conete cot nd/o footnt. programming lt3800 v in uvlo 3800 ai02 lt3800 v in r b r a 3 17 shdn sgnd
lt3800 15 3800fc applications information some magnetics vendors specify a volt-second product in their data sheet. if they do not, consult the vendor to make sure the speci? cation is not being exceeded by your design. the required volt-second product is calculated as follows: volt-second  v out f o ?1C v out v in       magnetics vendors specify either the saturation current, the rms current, or both. when selecting an inductor based on inductor saturation current, the peak current through the inductor, i out(max) + ( ? i/2), is used. when selecting an inductor based on rms current the maximum load current, i out(max) , is used. the requirement for avoiding current mode instability is keeping the rising slope of sensed inductor ripple current (s1) greater than the falling slope (s2). during continuous- current switcher operation, the rising slope of the current waveform in the switched inductor is less than the falling slope when operating at duty cycles (dc) greater than 50%. to avoid the instability condition during this operation, a false signal is added to the sensed current, increasing the perceived rising slope. to prevent current mode instability, the slope of this false signal (sx) must be suf? cient such that the sensed rising slope exceeds the falling slope, or s1 + sx s2. this leads to the following relations: sx s2 (2dc C 1)/dc where: s2 ~ v out /l solving for l yields a relation for the minimum inductance that will satisfy slope compensation requirements: l min = v out ? 2dc C 1 dc ? sx te lt300 xe lle dnc ne n loe coenton eneto tt contnol ncee te ddtonl nl loe dt ccle ncee. te loe coenton efo clted t n 0 dt ccle to enete n elent loe of t let 1e 5 ? i limit a/ec ee i limit te oed con- ete cent lt. cent lt oed n ene eto (r s ) c tt i limit 150v/r s o te eton fo te n ndctnce to eet te cent ode ntlt cteon cn e edced to l min (5e C5 )(v out )(r s ) o exle t v out 5v nd r s 20 l min (5e C5 )(5)(0.02) 5h afte clcltn te n ndctnce le te olt- econd odct te tton cent nd te rms cent fo o den n off te elf ndcto cn e elected fo netc endo. a lt of netc endo cn e fond t tt//.lne.co/eone/ln o contctn te lne tecnolo alcton detent. output voltage programming output voltage is programmed through a resistor feedback network to v fb (pin 6) on the lt3800. this pin is the inverting input of the error ampli? er, which is internally referenced to 1.231v. the divider is ratioed to provide 1.231v at the v fb pin when the output is at its desired value. the output voltage is thus set following the relation: r2 = r1? v out 1.231 C1       when an external resistor divider is connected to the output as shown. programming lt3800 output voltage 3800 ai03 lt3800 v out r2 r1 6 17 v fb sgnd
lt3800 16 3800fc applications information power mosfet selection external n-channel mosfet switches are used with the lt3800. the positive gate-source drive voltage of the lt3800 for both switches is roughly equivalent to the v cc supply voltage, for use of standard threshold mosfets. selection criteria for the power mosfets include the on resistance (r ds(on) ), total gate charge (q g ), reverse transfer capacitance (c rss ), maximum drain-source volt- age (v dss ) and maximum current. the power fets selected must have a maximum operating v dss exceeding the maximum v in . v gs voltage maximum must exceed the v cc supply voltage. total gate charge (q g ) is used to determine the fet gate drive currents required. q g increases with applied gate voltage, so the q g for the maximum applied gate voltage must be used. a graph of q g vs. v gs is typically provided in mosfet data sheets. in a con? guration where the lt3800 linear regulator is providing v cc and v boost currents, the v cc 8v output voltage can be used to determine q g . required drive cur- rent for a given fet follows the simple relation: i gate = q g(8v) ? f o q g(8v) is the total fet gate charge for v gs = 8v, and f 0 = operating frequency. if these currents are externally derived by backdriving v cc , use the backfeed voltage to determine q g . be aware, however, that even in a backfeed con? gura- tion, the drive currents for both boosted and synchronous fets are still typically supplied by the lt3800 internal v cc regulator during start-up. the lt3800 can start using fets with a combined q g(8v) up to 180nc. once voltage requirements have been determined, r ds(on) can be selected based on allowable power dissipation and required output current. in an lt3800 buck converter, the average inductor cur- rent is equal to the dc load current. the average cur- rents through the main (bootstrapped) and synchronous (ground-referred) switches are: i main = (i load )(dc) i sync = (i load )(1 C dc) the r ds(on) required for a given conduction loss can be calculated using the relation: p loss = i switch 2 ? r ds(on) in high voltage applications (v in > 20v), the main switch is required to slew very large voltages. mosfet transition losses are proportional to v in 2 and can become the domi- nant power loss term in the main switch. this transition loss takes the form: p tr (k)(v in ) 2 (i switch )(c rss )(f o ) where k is a constant inversely related to the gate drive current, approximated by k = 2 in lt3800 applications, and i switch is the converter output current. the power loss terms for the switches are thus: p main = (dc)(i switch ) 2 (1 + d)(r ds(on) ) + 2(v in ) 2 (i switch )(c rss )(f o ) p sync = (1 C dc)(i switch ) 2 (1 + d)(r ds(on) ) the (1 + d) term in the above relations is the temperature dependency of r ds(on) , typically given in the form of a normalized r ds(on) vs temperature curve in a mosfet data sheet. the c rss term is typically smaller for higher voltage fets, and it is often advantageous to use a fet with a higher v ds rating to minimize transition losses at the expense of additional r ds(on) losses. in some applications, parasitic fet capacitances couple the negative going switch node transient onto the bottom gate drive pin of the lt3800, causing a negative voltage in excess of the absolute maximum rating to be imposed on that pin. connection of a catch schottky diode from this pin to ground will eliminate this effect. a 1a current rating is typically suf? cient for the diode. input capacitor selection the large currents typical of lt3800 applications require special consideration for the converter input and output supply decoupling capacitors. under normal steady state buck operation, the source current of the main switch mosfet is a square wave of duty cycle v out /v in . most of this current is provided by the input bypass capacitor.
lt3800 17 3800fc applications information to prevent large input voltage transients and avoid bypass capacitor heating, a low esr input capacitor sized for the maximum rms current must be used. this maximum capacitor rms current follows the relation: i rms = i max v out v in Cv out () () 1 2 v in c e t 50 dt ccle en i rms i max /2. te l cctnce clclted ed on n ccet- le x nt le olte ? v in , which follows the relation: c in(bulk) = i out(max) ? v out v in  v in ?f o ? v is typically on the order of 100mv to 200mv. aluminum electrolytic capacitors are a good choice for high voltage, bulk capacitance due to their high capacitance per unit area. the capacitor voltage rating must be rated greater than v in(max) . the combination of aluminum electrolytic ca- pacitors and ceramic capacitors is a common approach to meeting supply input capacitor requirements. multiple capacitors are also commonly paralleled to meet size or height requirements in a design. capacitor ripple current ratings are often based on only 2000 hours (three months) lifetime; it is advisable to derate either the esr or temperature rating of the capacitor for increased mtbf of the regulator. output capacitor selection the output capacitor in a buck converter generally has much less ripple current than the input capacitor. peak-to- peak ripple current is equal to that in the inductor ( ? i l ), typically a fraction of the load current. c out is selected to reduce output voltage ripple to a desirable value given an expected output ripple current. output ripple ( ? v out ) is approximated by: ? v out ? i l (esr + [(8)(f o ) ? c out ] C1 ) where f o = operating frequency. ? v out increases with input voltage, so the maximum operating input voltage should be used for worst-case calculations. multiple capacitors are often paralleled to meet esr requirements. typically, once the esr require- ment is satis? ed, the capacitance is adequate for ? ltering and has the required rms current rating. an additional ceramic capacitor in parallel is commonly used to reduce the effect of parasitic inductance in the output capacitor, which reduces high frequency switching noise on the converter output. increasing inductance is an option to reduce esr require- ments. for extremely low ? v out, an additional lc ? lter stage can be added to the output of the supply. application note 44 has information on sizing an additional output lc ? lter. layout considerations the lt3800 is typically used in dc/dc converter designs that involve substantial switching transients. the switch drivers on the ic are designed to drive large capacitances and, as such, generate signi? cant transient currents them- selves. careful consideration must be made regarding supply bypass capacitor locations to avoid corrupting the ground reference used by ic. typically, high current paths and transients from the input supply and any local drive supplies must be kept isolated from sgnd, to which sensitive circuits such as the error amp reference and the current sense circuits are referred. effective grounding can be achieved by considering switch current in the ground plane, and the return current paths of each respective bypass capacitor. the v in bypass return, v cc bypass return, and the source of the synchronous fet carry pgnd currents. sgnd originates at the negative terminal of the v out bypass capacitor, and is the small signal reference for the lt3800. dont be tempted to run small traces to separate ground paths. a good ground plane is important as always, but pgnd referred bypass elements must be oriented such that transient currents in these return paths do not corrupt the sgnd reference. during the dead-time between switch conduction, the body diode of the synchronous fet conducts inductor
lt3800 18 3800fc applications information current. commutating this diode requires a signi? cant charge contribution from the main switch. at the instant the body diode commutates, a current discontinuity is created and parasitic inductance causes the switch node to ? y up in response to this discontinuity. high cur- rents and excessive parasitic inductance can generate extremely fast dv/dt rise times. this phenomenon can cause avalanche breakdown in the synchronous fet body diode, signi? cant inductive overshoot on the switch node, and shoot-through currents via parasitic turn-on of the synchronous fet. layout practices and component orientations that minimize parasitic inductance on this node is critical for reducing these effects. ringing waveforms in a converter circuit can lead to device failure, excessive emi, or instability. in many cases, you can damp a ringing waveform with a series rc network across the offending device. in lt3800 applications, any ringing will typically occur on the switch node, which can usually be reduced by placing a snubber across the synchronous fet. use of a snubber network, however, should be considered a last resort. effective layout practices typically reduce ringing and overshoot, and will eliminate the need for such solutions. effective grounding techniques are critical for successful dc/dc converter layouts. orient power path components such that current paths in the ground plane do not cross through signal ground areas. signal ground refers to the exposed pad on the backside of the lt3800 ic. sgnd is referenced to the (C) terminal of the v out decoupling capacitor and is used as the converter voltage feedback reference. power ground currents are controlled on the lt3800 via the pgnd pin, and this ground references the high current synchronous switch drive components, as well as the local v cc supply. it is important to keep pgnd and sgnd voltages consistent with each other, so separating these grounds with thin traces is not recom- mended. when the synchronous fet is turned on, gate drive surge currents return to the lt3800 pgnd pin from the fet source. the boost supply refresh surge currents also return through this same path. the synchronous fet must be oriented such that these pgnd return currents do not corrupt the sgnd reference. problems caused by the pgnd return path are generally recognized during heavy load conditions, and are typically evidenced as multiple switch pulses occurring during a single 5s switch cycle. this behavior indicates that sgnd is being corrupted and grounding should be improved. sgnd corruption can often be eliminated, however, by adding a small capacitor (100pf-200pf) across the synchronous switch fet from drain to source. the high di/dt loop formed by the switch mosfets and the input capacitor (c in ) should have short wide traces to minimize high frequency noise and voltage stress from inductive ringing. surface mount components are preferred to reduce parasitic inductances from component leads. connect the drain of the main switch mosfet directly to the (+) plate of c in , and connect the source of the syn- chronous switch mosfet directly to the (C) terminal of c in . this capacitor provides the ac current to the switch mosfets. switch path currents can be controlled by orienting switch fets, the switched inductor, and input and output decoupling capacitors in close proximity to each other. locate the v cc and boost decoupling capacitors in close proximity to the ic. these capacitors carry the mosfet drivers high peak currents. locate the small-signal components away from high frequency switching nodes (boost, sw, tg, v cc and bg). small-signal nodes are oriented on the left side of the lt3800, while high current switching nodes are oriented on the right side of the ic to simplify layout. this also helps prevent corruption of the sgnd reference. connect the v fb pin directly to the feedback resistors independent of any other nodes, such as the sense C pin. the feedback resistors should be connected between the (+) and (C) terminals of the output capacitor (c out ). locate the feedback resistors in close proximity to the lt3800 to minimize the length of the high impedance v fb node. the sense C and sense + traces should be routed together and kept as short as possible.
lt3800 19 3800fc applications information the lt3800 packaging has been designed to ef? ciently remove heat from the ic via the exposed pad on the backside of the package. the exposed pad is soldered to a copper footprint on the pcb. this footprint should be made as large as possible to reduce the thermal resistance of the ic case to ambient air. orientation of components isolates power path and pgnd currents, preventing corruption of sgnd reference boost v cc sw pgnd sgnd lt3800 sgnd referred components + + bg tg v out 3800 ai05 v in i sense sw typical applications 6.5v-55v to 5v 10a dc/dc converter with charge pump doubler v cc refresh and current limit foldback v in nc shdn c ss burst_en v fb v c sense C boost tg sw nc v cc bg pgnd sense + lt3800 sgnd c7 1.5nf r3 62k r5 47k d2 1n4148 r4 75k c9 470pf c10 100pf r2 309k 1% r1 100k 1% r a 1m r s 0.01 d1 bas19 c1 1f 16v x7r c3 1f 16v x7r c2 1f 100v x7r 3 c8 56f 63v 2 + c6 10f 6.3v x7r c5 220f 2 + m1 si7850dp 2 m2 si7370dp 2 m3 1/2 si1555dl m4 1/2 si1555dl ds3 b160 2 ds1 mbro520l c4 1 f ds2 mbro520l l1 5.6h v in 6.5v to 55v v out 5v at 10a 3800 ta02a c5: sanyo poscap 6tp220m l1: ihlp-5050fd-01 ef? ciency and power loss i out (a) 0 70 efficiency (%) power loss (w) 75 80 85 90 95 100 0 2 4 6 8 10 12 2468 3800 ta02b 10 v in = 13.8v v in = 55v v in = 24v v in = 48v power loss v in = 48v power loss v in = 13.8v
lt3800 20 3800fc typical applications 9v-38v to 3.3v 10a dc/dc converter with input uvlo and burst mode operation no load i(v in ) = 100a ef? ciency and power loss v in nc shdn c ss burst_en v fb v c sense C boost tg sw nc v cc bg pgnd sense + lt3800 sgnd c1 1nf c3 100pf c2 330pf c10 100pf r2 169k 1% r1 100k 1% r4 39k r3 82k r a 1m r b 187k r s 0.01 d1 mbr520 c5 1f 16v x7r c4 1f 16v x7r c9 4.7f 50v x7r 3 c8 100f 50v 2 + c7 10f 6.3v x7r c6 470f 2 + m1 si7884dp m2 si7884dp ds1 ss14 2 l1 3.3 h v in 9v to 38v v out 3.3v at 10a 3800 ta03a c6: sanyo poscap 4tpd470m l1: ihlp-5050fd-01 i load (a) 78 84 82 80 92 90 88 86 0 3 2 1 7 6 5 4 3800 ta03b efficiency (%) power loss (w) 0.1 10 1 v in = 13.8v
lt3800 21 3800fc typical applications 9v-38v to 5v 6a dc/dc converter with all ceramic capacitors, input uvlo, burst mode operation and current limit foldback ef? ciency and power loss v in nc shdn c ss burst_en v fb v c sense C boost tg sw nc v cc bg pgnd sense + lt3800 sgnd c1 3.9nf c9 1nf c3 100pf c2 1nf c6 47pf r2 154k 1% r1 49.9k 1% r5 47k d2 1n4148 r4 51k r3 27k r a 1m r b 187k r s 0.02 d1 bas19 c5 1f 10v x7r c4 1f 10v x7r c8 22f 3 c7 100f 2 m1 si7884dp m2 si7884dp ds1 ss14 l1 10 h v in 9v to 38v v out 5v at 6a 3800 ta05a c7: tdk c4532x5r0j107mt c8: tdk c5750x7r1e226mt l1: ihlp-5050fd-01 i load (a) 70 efficiency (%) power loss (w) 80 85 95 100 0.001 0.1 1 10 3800 ta05b 60 0.01 90 75 65 0.80 1.60 2.00 2.80 3.20 0 2.40 1.20 0.40 v in = 13.8v
lt3800 22 3800fc package description please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. fe package 16-lead plastic tssop (4.4mm) (reference ltc dwg # 05-08-1663 rev i) exposed pad variation bc fe16 (bc) tssop rev i 1210 0.09 C 0.20 (.0035 C .0079) 0 s C 8 s 0.25 ref 0.50 C 0.75 (.020 C .030) 4.30 C 4.50* (.169 C .177) 134 5 6 7 8 10 detail b is the part of the lead frame feature for reference only no measurement purpose 9 4.90 C 5.10* (.193 C .201) 16 1514 13 12 11 1.10 (.0433) max 0.05 C 0.15 (.002 C .006) 0.65 (.0256) bsc 2.94 (.116) 0.48 (.019) ref 0.51 (.020) ref 0.195 C 0.30 (.0077 C .0118) typ 2 recommended solder pad layout 0.45 t 0.05 0.65 bsc 4.50 t 0.10 6.60 t 0.10 1.05 t 0.10 2.94 (.116) 3.58 (.141) 3.58 (.141) millimeters (inches) *dimensions do not include mold flash. mold flash shall not exceed 0.150mm (.006") per side note: 1. controlling dimension: millimeters 2. dimensions are in 3. drawing not to scale see note 4 4. recommended minimum pcb metal size for exposed pad attachment 6.40 (.252) bsc detail b
lt3800 23 3800fc information furnished by linear technology corporation is believed to be accurate and reliable. however, no responsibility is assumed for its use. linear technology corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. revision history rev date description page number c 9/11 minor correction to ta04a schematic 24 (revision history begins at rev c)
lt3800 24 3800fc linear technology corporation 1630 mccarthy blvd., milpitas, ca 95035-7417 (408) 432-1900 fax: (408) 434-0507 www.linear.com ? linear technology corporation 2005 lt 0911 rev c ? printed in usa related parts typical application 24v-48v to C12v 75w inverting dc/dc converter with v in uvlo ef? ciency and power loss i load (a) 0.1 40 efficiency (%) power loss (w) 50 60 70 80 100 110 3800 ta04b 90 0 2 4 6 8 12 10 v in = 24v v in = 48v v in = 36v loss v in = 36v part number description comments ltc1735 synchronous step-down controller 4v v in 36v, 0.8v v out 6v, i out 20a ltc1778 no r sense ? synchronous step-down controller current mode without using sense resistor, 4v v in 36v lt ? 1934 micropower step-down switching regulator 3.2v v in 34v, 300ma switch, thinsot? package lt1952 synchronous single switch forward converter 25w to 500w isolated power supplies, small size, high ef? ciency lt1976 60v switching regulator 3.2v v in 60v, 1.5a switch, 16-lead tssop lt3010 3v to 80v ldo 50ma output current, 1.275v v out 60v lt3430/lt3431 3a, 60v switching regulators 5.5v v in 60v, 200khz, 16-lead tssop ltc3703 100v synchronous step-down controller large 1 gate drivers, no r sense ltc3703-5 60v synchronous step-down controller large 1 gate drivers, no r sense ltc3727-1 high v out 2-phase dual step-down controller 0.8v v out 14v, pll: 250khz to 550khz ltc3728l 2-phase, dual synchronous step-down controller 550khz, pll: 250khz to 550khz, 4v v in 36v v in nc shdn c ss burst_en v fb v c sense C boost tg sw nc v cc bg pgnd sense + lt3800 sgnd c1 1nf r1 200k c3 470pf r8 1m r3 1m r7 1m r6 130k r4 39k r5 20k 1% r2 174k 1% c2 1f 16v x7r c4 100pf c8 4.7f 16v x7r c5 270f 16v sprague sp c7 150pf 100v d2 1n4148 d1 bas19 c9 56f 63v w 2 c10 1f 100v x7r w 4 c6 1f 16v x7r m1 fdd3570 m2 fdd3570 l1: coev mgpwl-00099 v in 24v to 48v v out C12v 75w r s 0.01 l1 15h ds1 b180 2n3906 3800 ta04a + +


▲Up To Search▲   

 
Price & Availability of LT3800-15

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X