 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| IB908F intel ? haswell - ult 3. 5 d isk size sbc users manual version 1 . 0
ii IB908F users manual acknowledgments a mi is a registered trademark of a merican megatrends inc. ps/2 is a trademark of international business machines corporation. intel and intel? 4 th generation mobi le core tm i mcp processor are registered trademarks of intel corporation. microsoft windows is a registered trademark of microsoft corporation. nuvoton is a registered trademark of nuvoton technology corporation. all other product names or trademarks are p roperties of their respective owners. IB908F users manual iii table of contents introduction ................................ ....................... 1 product description ................................ ............................. 1 checklist ................................ ................................ .............. 2 IB908F specifications ................................ ......................... 2 board dimensions ................................ ............................... 4 installations ................................ ....................... 5 installing the memory ................................ ......................... 6 setting the jumpers ................................ ............................. 7 connectors on IB908F ................................ ...................... 11 bios setup ................................ ....................... 23 drivers installation ................................ ...... 49 intel chipset software installation utility ........................ 50 vga drivers instal lation ................................ .................. 53 realtek hd audio driver installation .............................. 56 lan drivers installation ................................ ................... 58 intel? management engine interface ............................... 62 intel? usb 3.0 drive rs ................................ ..................... 65 appendix ................................ ............................ 68 a. i/o port address map ................................ .................. 68 b. interrupt request lines (irq) ................................ ...... 69 c. watchdog timer configuration ................................ ... 70 iv IB908F users manual this page is intentionally left blank. intr oduction IB908F users manual 1 introduction product description t he IB908F is a 3.5 - inch single board computer based on the intel ? haswell - ult mcp processors. the IB908F platform is well - suited for low - power and high - perform ance designs in a broad range of markets including industrial control & automation, digital signage, thin client, electronic gaming machines, and smb storage appliances. IB908F features: ? supports intel ? 4 th generation mobile core tm i mcp processors ? two d dr3 l so - dimm, 1333/1600 mhz, max. 16 gb memory ? integrated g raphics for dvi - i , lvds displays ? 2 x sata iii connector ? 2 x com p ort c onnector ? 2 x mini - pcie(x1) slot (w/ usb /msata support) ? 2 x gbe (rj - 45) c onnector ? 1x 9v to 24v dc - in power connector introduction 2 IB908F users manual checkli st your IB908F package should include the items listed below. ? the IB908F sbc ? this users manual ? 1 cd containing chipset drivers and flash memory utility ? optional cable kit (containing dc in power cable/pw87, com port cable / pk1h, sata & hdd power cable /sata - 26 and usb 2.0 cable/usb - 29) ? other options: audio - 18 audio cable, hsib908 - bga - 1 heatsink IB908F specifications product name ib908 f form factor 3.5 sbc cpu type - inte l ? 4 th generation mobile core tm i mcp processors (22nm monolithic) - tdp = 15w (dc) , fcbga1168 @ solder side cpu speed intel ? core tm i7 - 4650u processor (1.7ghz) [IB908F - 4650] intel ? core tm i5 - 4300u processor (1.9ghz) [IB908F - 4300] [ib908af - 4300] intel ? core t m i3 - 4010u processor (1.7ghz) [IB908F - 4010] cache up to 4mb chipset integrat e d in intel ? 4 th generation core tm i u - series processor bios a mi bios memory intel ? 4 th gen . core tm i u - series processor integrated memory controller - ddr 3l (1.35v) @ 1600 mhz, so - dimm [204 - pin vertical] x 2 - max. 16gb, non - ecc display intel ? 4 th gen . core tm i u - series processor integrated gfx, supports 3 independent displays, direct x 11.1, opengl 3.2, open cl 1.2 - dvi - i x 1 (thru ddi#1 w/ level shifter [asm1442k] for dvi + dp to vga [nxp ptn3392] ) lvds - lvds( thru edp, via nxp ptn3460 bridge ic ) 24 - bit dual channels lvds interface w/ df 20 s ocket x 2 lan 1. inte l ? i218lm gbe phy (IB908F - 4650 & ib908af - 4300 ) or i218v gbe phy ( IB908F - 4300 & IB908F - 4010) 2. i nte l ? i211at as 2 nd gbe usb - inte l ? 4 th gen . core tm i u - series processor integrated usb 2.0 host controller, s upport s 6 x usb 2.0: 2 - ports onboard pin header + 2 port thru minipcie - intel ? 4 th gen . core tm i u - series processor integrated usb 3 .0 host controller, support s 2 x usb 3 .0 in the rear panel intr oduction IB908F users manual 3 serial ata ports intel ? 4 th gen . core tm i u - series processor built - in sata controller 2 x sata 3.0 ( 6gbps ) and 2 x msata via minipcie slots (w/nxp cbtl02043a switching ic) audio intel ? 4 th gen . core tm i u - series processor b uilt - in high definition audio controller + realtek alc269 q - vc2 - gr codec [6mm x 6 mm @ m qfn 48 ] w/ class - d speaker amplifier(2w per channel @ 5v power supply) lpc i/o nuvoton nct6102d [128 - pin lqfp, 14 mm x 14mm x 1.4mm ) com1 (rs232/422/485) [exar sp339eer1 232/422/485 transceiver for jumper - less ]; com2 (rs232 only) [sipex sp3243eber, qfn32] [hardware monitor] 2 x t hermal inputs 2 x v oltage monitor ing 1 x cpu fan (pwm fan type, 4 - pin connector) digital io 4 in & 4 out i amt (9.5) for IB908F - 4650 / ib908af - 4 30 0 expansion slots 1x msata/ mpcie(x1) w/ usb signal [half - sized] 1x msata/mpcie(x1) w/ usb signal [full - sized] edge connector dvi - i x 1 rj45 x 2 for lan #1 & #2 usb 3.0 stack connector x 1 for usb1 / 2 [blue color] db9 x 1 for com #1 onboard header/conn ector df20 - 20 socket connector x 2 for 24 - bit dual channel lvds 2 ports x sata iii [blue color] 2x4 pins header x 2 for 4 usb 2.0 ports [ df11] 2x6 pin s box header x1 for audio [df11] 1x4 pins box header x1 for speaker out 2x5 pins box header x1 for com 2 2x5 pins headers x 1 for lpc (debug purposes only) 5 pins box header x1 for smart battery 4 pins box header x1 for backlight/brightness control 4 pins power connector x1 for sata hdd 2 pins power connector x1 for dc - in [180 degree vertical type] watchdog timer yes (256 segments, 0, 1, 2255 sec/min) power input +9v ~ +24v dc - in rohs yes board size 102mm x 147 mm os supported windows 8 / embedded; windows 7 / embedded linux others 1. heatsink 2. i - smart (auto - scheduler & power fail resume function) 3. eeprom 2 4c02(reserved for designing, m - so8 package) introduction 4 IB908F users manual board dimensions installations IB908F users manual 5 installations this section provides information on how to use the jumpers and connectors on the IB908F in order to set up a workable system. the topics covered are: installing the me mory ................................ ................................ ............ 6 setting the jumpers ................................ ................................ ................ 7 connectors on IB908F ................................ ................................ ......... 11 installations 6 IB908F users manual installing the memory the IB908F board supports two ddr3l memory socket for a maximum total memory of 16gb ddr 3l memory type. installing and removing memory modules to install the ddr3l modules, locate the memory slot on the board and perform the following steps: 1. hold the ddr3l module so that the key of the ddr3l module align ed with th at on the memory slot. 2. gently push the ddr3l module in an upright position until the clips of the slot close to hold the ddr3l module in place when the ddr3l module touches the bottom of the slot. 3. to remove the ddr3l module, press the clips with both hands. installations IB908F users manual 7 setting the jumpers ju mpers are used on IB908F to select various settings and features according to your needs and applications. contact your supplier if you have doubts about the best configuration for your needs. the following lists the connectors on IB908F and their respecti ve functions. jumper locations on IB908F ................................ ................................ . 8 j3: clear cmos contents ................................ ................................ ...... 9 j4: clear me contents ................................ ................................ ........... 9 j7: flash descriptor security override (factory use only) .................. 10 j9: lvds panel power selection ................................ ........................ 10 installations 8 IB908F users manual jumper locations on IB908F jumpers on IB908F ................................ ................................ .......... page j 3 : clear cmos contents ................................ ................................ ...... 9 j 4 : clear me contents ................................ ................................ ........... 9 j 9 : lvds panel power selection ................................ ......................... 10 installations IB908F users manual 9 j3: clear cmos contents j3 setting function pin 1 - 2 short/closed normal pin 2 - 3 short/closed clear cmos j 4 : clear me contents j4 setting fu nction pin 1 - 2 short/closed normal pin 2 - 3 short/closed clear m e rtc register 3 1 3 1 installations 10 IB908F users manual j 7 : flash descriptor security override (factory use only) j 7 flash descriptor security override open disabled (default) close enabled j9: lvds panel power s election jp 9 setting panel voltage pin 1 - 2 short/closed 3.3v (default) pin 2 - 3 short/closed 5v 1 3 installations IB908F users manual 11 connectors on IB908F connector locations on IB908F ................................ .......................... 12 cn3, cn4: gigabit lan ................................ ................................ ..... 13 cn3: intel? clarkville i218v/i218lm gbe phy ............................... 13 cn4: intel? pearsonville i211at as 2nd gbe ................................ ... 13 cn5: usb 1/2 connector ................................ ................................ .... 13 cn6: vga dvi - i connector ................................ ............................... 13 cn7: db9 connector ................................ ................................ .......... 13 cn1, cn2: sata connectors ................................ ............................. 14 jp1: lcd backlight connector ................................ ........................... 14 jp2: usb3/4 connector ................................ ................................ ....... 14 j2: audio connector (df11 connector) ................................ .............. 15 jp3, jp5: lvds connectors (lvds1,lvds2) ................................ ... 15 jp4: spi flash connector (factory use only) ................................ ....... 16 j5: amplifier connector ................................ ................................ ...... 16 j7: factory use only ................................ ................................ ............. 16 jp6: sata hdd power connectors ................................ ................... 17 jp7: debug 80 port connector (factory use only) ............................... 17 j12: smart battery ................................ ................................ ............... 18 j13: board input power connector ................................ ...................... 18 j14: front panel connector ................................ ................................ . 19 j15: mini pcie connector (supports msata) ................................ .. 20 j16: mini pcie connector (half size/ s upports msata) .................. 20 j17: com2/rs232 serial port ................................ ............................ 20 j19: digital i/o connector ................................ ................................ ... 21 cpu_fan1: cpu fan power connector ................................ ........... 21 installations 12 IB908F users manual connector locat ions on IB908F installations IB908F users manual 13 cn3, cn4: gigabit lan cn3: intel? clarkville i21 8 v /i218lm gbe phy cn4: intel? pearsonville i211at as 2nd gbe cn5: usb 1/2 connector cn6: vga dvi - i connector cn7: db9 connector (com1) is a db - 9 conne ctor. signal name pin # pin # signal name dcd, data carrier detect 1 6 dsr, data set ready rxd, receive data 2 7 rts, request to send txd, transmit data 3 8 cts, clear to send dtr, data terminal ready 4 9 ri, ring indicator gnd, ground 5 10 not used com1 is jumper - less for rs - 232, rs - 422 and rs - 485 and is to be configured with bios selection. [ pin # signal name rs - 232 r2 - 422 rs - 485 1 dcd t x - data - 2 rx t x + data+ 3 tx r x+ nc 4 dtr r x - nc 5 ground ground ground 6 dsr nc nc 7 rts nc nc 8 cts nc nc 9 ri nc nc 10 nc nc nc installations 14 IB908F users manual cn1, cn2 : sata connector s jp1: lcd backlight connector pin # signal name 1 +12v 2 backlight enable 3 b rightness control 4 ground jp2: usb3/4 connector signal name pin # pin # signal name vcc 1 2 ground d0 - 3 4 d1+ d0+ 5 6 d1 - ground 7 8 vcc 4 1 2 1 8 7 installations IB908F users manual 15 j2: audio connector (df11 connector) signal name pin # pin # signal name lineout_r 2 1 lineout_l ground 4 3 jd_front linein_r 6 5 linein_l ground 8 7 jd_linein m i c - r 10 9 mic_l ground 12 11 jd_mic1 jp3 , jp5: lvds connectors ( lvds1,lvds2) the lvds connectors ( hirose df20g - 20dp - 1v ) on board consist of the first channel (lvds1) and second channel (lvds2). signal name pin # pin # signal name tx0n 2 1 tx0 p ground 4 3 ground tx1n 6 5 tx1p ground 8 7 ground tx2n 10 9 tx2p ground 12 11 ground clkn 14 13 clkp ground 16 15 ground tx3n 18 17 tx3p power 20 19 power 1 11 2 12 2 20 1 19 installations 16 IB908F users manual jp4: spi flash connector (factory use only) j 5 : amplifier connector pin # signal name 1 outl+ 2 outl - 3 outr - 4 outr+ j 6, j8 : ddr3 l so - dimm socket s j7: factory use only 9 10 1 2 1 4 1 2 installations IB908F users manual 17 j p6 : sata hdd power connector s pin # signal name 1 +5v 2 ground 3 ground 4 +12v j p7 : debug 80 port connector (factor y use only) j 11 : mcu flash connector (factory use only) 1 4 1 4 2 10 1 9 installations 18 IB908F users manual j12: s mart b attery pin # signal name 1 rst# 2 ichswi# 3 ground 4 smb_data 5 smb_clk j13 : board input power connector pin # signal name 1 +9v to +24v 2 g n d 1 2 1 5 installations IB908F users manual 19 j14 : front panel connector the following table shows the pin outs of the 2x4 pin header signal name pin # pin # signal name ground 1 2 pwr_sw pwr_led+ 3 4 pwr_led - hdd_led + 5 6 hdd_led - ground 7 8 reset j 14 provides connectors for s ystem indicators that provide light indication of the computer activities and switches to change the computer status. j 14 is a n 8 - pin header that provides interfaces for the following functions. atx power on switch: pins 1 and 2 this 2 - pin connector is an atx power supply on/off switch on the system that connects to the power switch on the case. when pressed, the power switch will force the system to power on. when pressed again, it will force the system to power off. power led: pins 3 and 4 pin # signal name 3 led(+) 4 led( - ) hard disk drive led connector: pins 5 and 6 this connector connects to the hard drive activity led on control panel. this led will flash when the hdd is being accessed. pin # signal name 5 led(+) 6 led( - ) 1 7 2 8 installations 20 IB908F users manual r eset switch: pins 7 and 8 the reset switch allows the user to reset the system without turning the main power switch off and then on again. orientation is not required when making a connection to this header. j 15 : mini pcie connector (supports msata) j 16 : mini pcie connector (half size/ supports msata) ** the gap of height between j15 & j16 is following pci express mini card electromechanical spec. ** j17: com2/rs232 serial port signal name pin # pin # signal name dcd, data car rier detect 1 2 rxd, receive data txd, transmit data 3 4 data terminal ready gnd, ground 5 6 dsr, data set ready rts, request to send 7 8 cts, clear to send ri, ring indicator 9 10 not used 2 1 10 9 installations IB908F users manual 21 j 19 : digital i/o connector signal name pin # pin # signal name gnd 1 2 vcc out3 3 4 out1 out2 5 6 out0 in3 7 8 in1 in2 9 10 in0 cpu_fan1: cpu fan power connector pin # signal name 1 ground 2 +12v 3 rotation detection 4 control 4 1 2 10 1 9 installations 22 IB908F users manual this page is intentionally left blank. drivers installation IB908F users manual 23 b ios setup this chapter describes the different settings available in the bios that comes with the board . the topics covered in this chapter are as follows: bios introduction ................................ ................................ ............... 24 bios setup ................................ ................................ .......................... 24 adv anced settings ................................ ................................ ............... 26 chipset settings ................................ ................................ ................... 39 boot settings ................................ ................................ ........................ 45 security settings ................................ ................................ .................. 47 save & exit settings ................................ ................................ ............ 48 bios setup 24 IB908F users manual bi os introduction the bios (basic input/output system) installed in your computer systems rom provides critical low - level support for a standard device such as disk drives, serial ports and parallel ports. it also adds virus and password protection as well as special support for detailed fine - tuning of the chipset controlling the entire system. bios setup the bios provides a setup utility program for specifying the system configurations and settings. the bios rom of the system stores the setup utility. when you turn on the computer, the bios is immediately activated. pressing the drivers installation IB908F users manual 25 main settings aptio setup utility C copyright ? 2011 american megatrends, inc. main adva nced chipset boot security save & exit bios information choose the system default language select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit total memory 8176 mb (ddr3) memory frequency 1600 mhz system date [tue 10/29/2013] s ystem time [15:27:20] access level administrator system date set the date. use tab to switch between data elements. system time set the time. use tab to switch between data elements. bios setup 26 IB908F users manual advanced settings this section allows you to configure and improve your system and allows you to set up some system features according to your preference. aptio setup utility main advanced chipset boot security save & exit select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit ? pci subsystem settings ? acpi settings ? wake up event setting ? cpu configuration ? sata configura tion ? shutdown temperature configuration ? ismart controller ? usb configuration ? nct6102d super io configuration ? nct6102d h/w monitor pci subsystem settings aptio setup utility main advanced chipset boot security save & exit pci bus driver version v 2.0502 select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit pci common settings pci lat ency timer 32 pci bus clocks vga palette snoop disabled perr# generation disabled serr# generation disabled ? pci express settings pci latency timer value to be programmed into pci latency timer register. vga palette snoop enables or d isables vga palette registers snooping. perr# generation enables or disables pci device to generate perr#. serr# generation enables or disables pci device to generate serr#. drivers installation IB908F users manual 27 pci express settings aptio setup utility main advanced chipset boot security save & exit pci express device register settings select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit relaxed ordering disabled extended tag disabled no snoop enabled maximum payload auto maximum read requ est auto pci express link register settings aspm support disabled warning: enabling aspm may cause pci - e devices to fail extended synch disabled link training retry 5 link training timeout (us) 100 unpopulated links keep link on restore pcie registers disabled relaxed ordering enables or disables pci express device relaxed ordering. extended tag if enabled allows device to use 8 - bit tag field as a requester. no snoop enables or disables pci express dev ice no snoop option. maximum payload set maximum payload of pci express device or allow system bios to select the value. maximum read request set maximum read request size of pci express device or allow system bios to select the value. aspm supp ort set the aspm level: force l0s C force all links to l0s state: auto C bios auto configure: disable C disables aspm. extended synch if enabled allows generation of extended synchronization patterns. bios setup 28 IB908F users manual link training retry defines number of retry attemp ts software will take to retrain the link if previous training attempt was unsuccessful. link training timeout (us) defines number of microseconds software will wait before polling link training bit in link status register. value range from 10 to 1000 u s. unpopulated links in order to save power, software will disable unpopulated pci express links, if this option set to disable link . restore pcie registers on non - pci express aware os s (pre windows vista) some devices may not be correctly reinitializ ed after s3.enabling this restore pci express device configuration on s3 resume warning: enabling this may cause issues with other hardware after s3 resume.1 drivers installation IB908F users manual 29 acpi settings aptio setup utility main advanced chipset boot security save & exit acpi settings select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit enable hibernation enabled acpi sleep state s3 (suspend to r ) l o ck legacy resources s3 video repost d isabled disabled enable hibernation enables or disables system ability to hibernate (os/s4 sleep state). this option may be not effective with some os. acpi sleep state select acpi sleep state the system will enter, when the suspend button is p ressed. l o ck legacy resources enabled or disabled lock of legacy resources. s3 video repost enable or disable s3 video repost. bios setup 30 IB908F users manual wake up event settings aptio setup utility main advanced chipset boot security save & exit select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit wake on pcie wake event disabled wake on pcie pme wake event the op tions are disabled and enabled. drivers installation IB908F users manual 31 cpu configuration this section shows the cpu configuration parameters. aptio setup utility main advanced chipset boot security save & exit cpu configuration intel(r) cpu core(tm)i3 - 4010u @ 1.70ghz select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit cpu signature processor family microcode patch fsb speed 40651 6 16 100mhz max cpu speed 1700 mhz min cpu s peed 800 mhz cpu speed 800 mhz processor cores 2 intel ht technology supported intel vt - x technology supported intel smx technology not supported 64 - bit supported eist supported cpu c3 state cpu c6 state cpu c7 state supported supported sup ported l1 data cache l1 code cache l2 cache l3cache supported supported supported supported hyper - threading enabled active processor cores overclocking lock all disabled limit cpuid maximum disabled execute disable bit enabled intel virtuali zation technology enabled cpu aes eist enabled enabled hyper - threading select the performance state that the bios will set before os handoff. active processor cores number of cores to enable in each processor package. overclocking lock flex_rat io(194)msr bios setup 32 IB908F users manual limit cpuid maximum disabled for windows xp. execute disable bit xd can prevent certain classes of malicious buffer overflow attacks when combined with a supporting os intel virtualization technology when enabled, a vmm can utilize the addi tional hardware capabilities provided by vanderpool technology. cpu aes enabled/disabled cpu advanced encryption standard instructions eist enabled/disabled intel speedstep. drivers installation IB908F users manual 33 sata configuration sata devices configuration. aptio setup utility main advanced chipset boot security save & exit select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit sata controller(s) enabled sata mode selection ahci sata port0 empty software preserve hot plug unknown disabled sata port1 empty software preserve hot plug unknown disabled sata port2 empty software preserve hot plug unknown disabled sata port3 empty software preserve hot plug unknown disabled sata controller(s) enable / disable serial ata controller. sata mode selection (1) ahci mode. (2) raid mode. hot plug designates this port as hot p;uggable. bios setup 34 IB908F users manual shutdown temperature configuration aptio setup utility main advanced chipset boot securit y save & exit select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit apci shutdown temperature disabled acpi shutdown temperature the default setting is disabled. ismart controller aptio setup utility main advanced chipset boot security save & exit ismart controller select screen select item enter: select + - change field f1: general help f2: previous values f3: optimize d default f4: save esc: exit power - on after power failure disable schedule slot 1 none schedule slot 2 none power - on after power failure enable or disable. schedule slot 1 / 2 setup the hour/minute for system power on. drivers installation IB908F users manual 35 amt configurat ion aptio setup utility main advanced chipset boot security save & exit select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit intel amt enabled bios hotkey pressed disabled mebx selection screen disabled hide un - configure me confir mation disabled un - configure me disabled amt wait timer 0 activate remote assistance process disabled usb configure enabled pet progress enabled amt cira timeout 0 watchdog disabled os timer 0 bios timer 0 amt configuratio n this configuration is supported iamt function. options are enabled and disabled. note: iamt h/ w is always enabled. this option just controls the bios extension execution. if enabled, this requires additional firmware in the spi device. unconfigure me pe rform amt/me unconfigure without password operation. amt wait timer set timer to wait before sending asf_get_boot_options. activate remote assistance process trigger cira boot. pet progress user can enable/disable pet events progress to receive pet even ts or not. watchdog timer enable/disable watchdog timer. bios setup 36 IB908F users manual usb configuration aptio setup utility main advanced chipset boot security save & exit usb configuration select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit usb module version 8.10.27 usb devices: 1 keyboard, 1 mouse legacy usb support enabled usb3.0 support enabled xhci hand - off enabled ehci hand - off enabled usb hardware delays and time - outs: usb transfer time - out 20 sec d e vice reset tine - out 20 sec d evice power - up delay auto legacy usb support enables legacy usb support. auto option disables legacy support if no usb devic es are connected. disable option keeps usb devices available only for efi applications. usb3.0 support enable/ disable usb3.0 (xhci) controller support. xhci hand - off this is a workaround for oses without xhci hand - off support. the xhci ownership change s hould be claimed by xhci driver. ehci hand - off enabled/disabled. this is a workaround for oses without ehci hand - off support. the ehci ownership change should be claimed by ehci driver. usb transfer time - out the time - out value for control, bulk, and inte rrupt transfers. d e vice reset time - out usb mass storage device start unit command time - out. d evice power - up delay maximum time the device will take before it properly reports itself to the host controller. auto uses default value: for a root port it is 100ms, for a hub port the delay is taken from hub descr iptor. drivers installation IB908F users manual 37 nct6102d super io configuration aptio setup utility main advanced chipset boot security save & exit nct6102d super io configuration select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit nct6102d super io chip nct6102d ? serial port 0 configuration ? serial port 1 configuration serial port configuration set parameters of serial ports. user can enable/disable the serial port and select an optimal settings for the super io device. bios setup 38 IB908F users manual nct6102d h/w monitor aptio setup utility main advanced chipset boot s ecurity save & exit pc health status select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit smart fan function disabled sys temp +40 c cpu temp cpufan speed +43 c 4166 vcore +1.808 v +5v +4.918 v +12v +12.000 v 1.35v +1.376 v smart fan function this field enables or disables the smart fan feature. at a certain temperature, the fan starts turning. once the temperature drops to a certain level, it stops turning again . temperatures/voltages these fields are the parameters of the hardware monitoring function feature of the board . the values are read - only values as monitored by the system and show the pc health status. drivers installation IB908F users manual 39 chipset settings this section allows you to co nfigure and improve your system and allows you to set up some system features according to your preference. aptio setup utility main advanced chipset boot security save & exit ? pch - io configuration ? system agent (sa) configuration pch - io configuration this section allows you to configure the north bridge chipset. aptio setup utility main advanced chipset boot security save & exit intel pch rc version 1.6.2.0 select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit intel pch sku name premium sku intel pch rev id 03/b1 ? pci express configuration ? usb configuration ? pch azalia configuration pch lan controller enabled wake on lan disabled slp_s4 assertion width 1 - 2 seconds pch lan controller enable or disable onboard nic. wake on lan enable or disable integrated lan to wake the system. (the wake on lan cannot be disabled if me is on at sx state.) slp_s4 assertion width select a minimum assertion width of the slp_s4# signal. bios setup 40 IB908F users manual p ci express configuration main advanced chipset boot security save & exit pci e xpress configuration select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit pci express clock gating disabled dmi link aspm control disabled dmi link extended synch control disab led pcie - usb glitch w/a disabled pcie root function swapping subtractive decode disabled disabled ? pci express root port 1 ? pci express root port 2 ? pci express root port 3 ? pci express root port 4 ? pci - e port 5 is assigned to la n ? pci express root port 6 pci express clock gating enable or disable pci express clock gating for each root port dmi link aspm control the control of active state power management on both nb side and sb side of the dmi link. pcie - usb glitch w/a pcie - usb glitch w/a for bad usb device(s) connected behind pcie/peg port. drivers installation IB908F users manual 41 usb configuration main advanced chipset boot security save & exit usb configuration select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit usb precondition disabled xhci mode auto xhci idle l1 enabled usb ports per - port disable control disabled usb precondition p recondition work on usb host controller and root ports for faster enumeration. xhci mode mode of operation of xhci controller. usb ports per - port disable control control each of the usb ports (0~13) disabling. pch azalia configuration main adva nced chipset boot security save & exit pch azalia configuration select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit azalia auto azalia pme d isabled azalia control detection of the azalia device. disabled = azalia will be unconditionally be disabled. enabled = azalia will be un conditionally be enabled . auto = azalia will be enabled if present, disabled otherwise. azalia pme enable or disab le power management capability of the audio controller. bios setup 42 IB908F users manual system agent (sa) configuration aptio setup utility main advanced chipset boot security save & exit system agent bridge name haswell select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit system agent rc version 1.6.2.0 vt - d capability supported vt - d enabled ? graphics configu ration vt - d check to enable vt - d function on mch. graphics configuration aptio setup utility main advanced chipset boot security save & exit graphics configuration select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit igfx vbios version 2166 igfx frequency 400 mhz primary display primary peg primary pcie auto auto auto internal graphics auto aperture size 256mb dvmt pre - allocated 32m dvmt total gfx mem ? lcd control 256mb primary display select which of igfx/peg/pci graphics device should be primary display or select sg for switchable gfx. drivers installation IB908F users manual 43 primary peg select pego/peg1/peg2/peg3 graphics device should be primary peg. primar y pcie select pcie0/pcie1/pcie2/pcie3/pcie4/pcie5/pcie6pcie7 graphics device should be primary pcie. internal graphics keep igd enabled based on the setup options. dvmt pre - allocated select dvmt 5.0 pre - allocated (fixed) graphics memory size used by the internal graphics device. dvmt total gfx mem select dvmt 5.0 total graphics memory size used by the internal graphics device. lcd control select the video device that will be activated during post. this has no effect if external graphics present. seconda ry booty display selection will appear based on your selection. vga modes will be supported only on primary display . bios setup 44 IB908F users manual lcd control aptio setup utility main advanced chipset boot security save & exit lcd control select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save & exit esc: exit primary igfx boot display vbios default lcd panel type dc output level 1024x768 lvds level4 lcd chanel type lvds backl i g ht brightness volt control active lfp single 3.3v no lvds panel color depth 24 bit primary igfx boot display select the video device, which will be activated during post. this has no effect if external graphics present . secondary boot displa y selection will appear based on your selection. vga modes will be supported only on primary display. lcd panel type select lcd panel used by internal graphics device by selecting the appropriate setup item: 640x480 lvds ~ 2048x1536 lvds. dc output level backlight brightness control lcd chanel type select lcd chanel type lvds back l i ght brightness volt control lvds back l i ght volt control: 3.3v , 5v active lfp select the active lfp configuration. no lvds: vbios does not enable lvds. int - lvds: vbios enab les lvds driver by integrated encoder. sdvo lvds: vbios enables lvds driver by sdvo encoder. edp port - a: lfp driven by int - displayport encoder from port - a. panel color depth select the lfp panel color depth: 18 bit, 24 bit. drivers installation IB908F users manual 45 boot settings this section al lows you to configure the boot settings . aptio setup utility main advanced chipset boot security save & exit boot configuration select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit setup prompt timeout 1 bootup numlock state on quiet boot disabled fast boot disabled boot option priorities ? csm16 parameters csm parameters setup prompt timeout number of seconds to wait for setup activation key. 65535(0xffff) means indefinite waiting. bootup numlock state select the keyboard numlock state. quiet boot enables/disables quiet boot option. fast boot enables/disables boot with initialization of a minimal set of devices required to launch active boot option. has no effect for bbs boot options. boot option priorities sets the system boot order. bios setup 46 IB908F users manual csm para meters oprom execution, boot options, filter, etc. aptio setup utility main advanced chipset boot security save & exit select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit launch csm emabled boot option filter uefi and legacy launch pxe oprom policy do not launch launch stora ge oprom policy legacy only launch video oprom policy legacy only other pci device rom priority legacy oprom launch csm this option controls if csm will be launched. boot option filter this option controls what devices system can boot to. launch pxe oprom policy controls the execution of uefi and legacy pxe oprom. launch storatge oprom policy controls the execution of uefi and legacy storage oprom. launch video oprom policy controls the execution of uefi and legacy video oprom. other pci device rom priority for pci devices other than network, mass storage or video defines which oprom to launch. drivers installation IB908F users manual 47 security settings this section allows you to configure and improve your system and allows you to set up some system features according to your preference. aptio setup utility main advanced chipset boot security save & exit password description select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit if only the administrator s password is set, then this only limit access to setup and is only asked for wh en entering setup. if only the user s password is set, then this is a power on password and must be entered to boot or enter setup. in setup the user will have administrator rights the password length must be in the following range: minimum length 3 maximum length 20 administrator password user password administrator password set setup administrator password. user password set user password. bios setup 48 IB908F users manual save & exit settings main advanced chipset boot security save & ex it save changes and exit select screen select item enter: select + - change field f1: general help f2: previous values f3: optimized default f4: save esc: exit discard changes and exit save changes and reset discard changes and re set save options save changes discard changes restore defaults save as user defaults restore user defaults save changes and exit exit system setup after saving the changes. discard changes and exit exit syste m setup without saving any changes. save changes and reset reset the system after saving the changes. discard changes and reset reset system setup without saving any changes. save changes save changes done so far to any of the setup options. discard ch anges discard changes done so far to any of the setup options. restore defaults restore/load defaults values for all the setup options. save as user defaults save the changes done so far as user defaults. restore user defaults restore the user defaults to all the setup options. drivers installation IB908F users manual 49 drivers installation this section describes the installation procedures for software and drivers. the software and drivers are included with the board . if you find the items missing, please contact the vendor where you made t he purchase. the contents of this section include the following: intel chipset software installation utility ................................ ........... 50 vga drivers installation ................................ ................................ ..... 53 realtek hd audio driver installation ................................ ................. 56 lan drivers installation ................................ ................................ ..... 58 intel? management engine interface ................................ .................. 62 intel? usb 3.0 drivers ................................ ................................ ....... 65 important note: after installing your windows operating sy stem, you must install first the intel chipset software installation utility before proceeding with the drivers installation. drivers installation 50 IB908F users manual intel chipset software installation utility the intel chipset drivers should be installed first before the software drivers to enable plug & play i n f support for intel chipset components. follow the instructions below to complete the installation. 1. insert the dvd that comes with the board . click intel and then intel(r) 8 series chipset drivers . 2. click intel(r) chipset software installation utility . drivers installation IB908F users manual 51 3. when the welcome screen to the intel ? chipset device software appears, click next to continue. 4. click yes to accept the software license agreement and proceed with the installation process. drivers installation 52 IB908F users manual 5. on the readme file information screen, click next to continue the installation. 6. the setup process is now complete. click finish to restart the computer and for changes to take effect. drivers installation IB908F users manual 53 vga drivers installation 1. insert the dvd that comes with the b oard . click intel and then intel(r) 8 series chipset drivers . 2. click intel(r) core(tm) i3/i5/i7 graphics driver . drivers installation 54 IB908F users manual 3. when the welcome screen appears, click next to continue. 4 . c lick yes to to agree with the license agreement and continue t he installation . drivers installation IB908F users manual 55 5. on the screen shown below, click install to continue. 6. setup complete. click finish to restart the computer and for changes to take effect. drivers installation 56 IB908F users manual realtek hd a udio d river installation 1. insert the dvd that comes with the board . click intel and then intel(r) 8 series chipset drivers . 2. click realtek high definition audio driver . drivers installation IB908F users manual 57 3 . on the welcome to the installshield wizard screen, click yes to proceed with and complete the installation process. 4 . the instal lshield wizard complete . click finish to restart the computer and for changes to take effect. drivers installation 58 IB908F users manual lan drivers installation 1. insert the dvd that comes with the board . click intel and then intel(r) 8 series chipset drivers . 2. click intel(r) pro lan network driver. drivers installation IB908F users manual 59 3. click install drivers and software. 4 . when the welcome screen appears, click next . drivers installation 60 IB908F users manual 5. c lick next to to agree with the license agreement . 6. click the checkbox for drivers in the setup options screen to select it and click next to continue. drivers installation IB908F users manual 61 7. the wizard is ready to begin installation. click install to begin the installation. 8. when installshield wizard is complete, click finish . drivers installation 62 IB908F users manual intel ? management engine interface 1. insert the dvd that comes w ith the board . click intel and then intel(r) 8 series chipset drivers and then intel(r) amt 9.5 drivers . drivers installation IB908F users manual 63 2 . when the welcome screen to the installshield wizard for intel ? management engine components , click the checkbox for install intel ? control c enter & click next . 3 . c lick yes to to agree with the license agreement . drivers installation 64 IB908F users manual 4 . when the setup progress screen appears, click next . then, click finish when the setup progress has been successfully installed. drivers installation IB908F users manual 65 intel? u sb 3.0 drivers 1. insert the dvd that comes with the board . click intel and then intel(r) 8 series chipset drivers . 2. click intel(r) usb 3.0 drivers. drivers installation 66 IB908F users manual 3 . when the welcome screen to the installshield wizard for intel ? usb 3.0 extensible host controller driver , click next . 4. c lick yes to to agree with the license agreement and continue the installation . drivers installation IB908F users manual 67 5. on the readme file information screen, click next to continue the installation of the intel ? usb 3.0 extensible host controller driver. 6 . setup complete. click fi nish to restart the computer and for changes to take effect. appendix 68 IB908F users manual appendix a. i/o port address map each peripheral device in the system is assigned a set of i/o port addresses which also becomes the identity of the device. the following table lists the i/o port addresses used. address device description 000h - 01fh dma controller #1 020h - 0 21 h interrupt controller #1 040h - 0 43 h timer 060h - 06 0 h keyboard controller 070h - 07 7 h real time clock, nmi 08 1 h - 09 1 h dma page register 0a0h C 0 a1 h interrupt controller #2 0 81 h - 0 91 h dma controller #2 040 h C 05f h smbus controler 2f8h - 2ffh serial port #2(com2) 3c 0 h - 3dfh graphics adapter controller d000 - ff f h pci - e root ports 3f8h - 3ffh serial port #1(com1) appendix IB908F users manual 69 b. interrupt request lines (ir q) peripheral devices use interrupt request lines to notify cpu for the service required. the following table shows the irq used by the devices on board. level function irq0 system timer output irq1 keyboard irq3 serial port #2 irq4 serial port #1 i rq8 real time clock irq1 0 smbus controller irq1 9 s ata ahci controller appendix 70 IB908F users manual c. watchdog timer configuration the wdt is used to generate a variety of output signals after a user programmable count. the wdt is suitable for use in the prevention of system lock - up, such as when software becomes trapped in a deadlock. under these sort s of circumstances, the timer will count to zero and the selected outputs will be driven. under normal circumstance, the user will restart the wdt at regular intervals before the timer counts to zero. sample code: // --------------------------------------------------------------------------- // // this code and information is provided "as is" without warra nty of any // kind, either expressed or implied, including but not limited to the // implied warranties of merchantability and/or fitness for a particular // purpose. // // --------------------------------------------------------------------------- #include appendix IB908F users manual 71 return 0; } // --------------------------------------------------------------------------- void enablewdt(int interval) { unsigned char bbuf; set_6106_ld(0x08); //switch to logic device 8 set_6106_ reg(0x30, 0x01); //enable timer set_6106_reg(0xf1, interval); //set timer } // --------------------------------------------------------------------------- void disablewdt(void) { unsigned char bbuf; set_6106_ld(0x08); //switch to logic de vice 7 set_6106_reg(0x30, 0x00); //enable timer } // --------------------------------------------------------------------------- // --------------------------------------------------------------------------- // // this code and information is provided "as is" without warranty of any // kind, either expressed or implied, including but not limited to the // implied warranties of merchantability and/or fitness for a pa rticular // purpose. // // --------------------------------------------------------------------------- #include "6 106.h" #include appendix 72 IB908F users manual } // --------------------------------------------------------------------------- void unlock_6106 (void) { outpor tb(6106_index_port, 6106_unlock); outportb(6106_index_port, 6106_unlock); } // --------------------------------------------------------------------------- void lock_6106 (void) { outportb(6106_index_port, 6106_lock); } // ---------------------------------- ----------------------------------------- void set_6106_ld( unsigned char ld) { unlock_6106(); outportb(6106_index_port, 6106_reg_ld); outportb(6106_data_port, ld); lock_6106(); } // ---------------------------------------------------------------------- ----- void set_6106_reg( unsigned char reg, unsigned char data) { unlock_6106(); outportb(6106_index_port, reg); outportb(6106_data_port, data); lock_6106(); } // --------------------------------------------------------------------------- unsigned char get_6106_reg(unsigned char reg) { unsigned char result; unlock_6106(); outportb(6106_index_port, reg); result = inportb(6106_data_port); lock_6106(); return result; } // --------------------------------------------------------------------------------- --- |
Price & Availability of IB908F
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |