- 196 - sf31g thru sf38g 3.0 amps. glass passivated super fast rectifiers voltage range 50 to 600 volts current 3.0 amperes features low forward voltage drop high current capability high reliability high surge curr ent capability mechanical data case: molded plastic epoxy: ul 94v-o rate flame retardant lead: axial leads, solderable per mil-std- 202, method 208 guaranteed polarity: color band denotes cathode end high temperature soldering guaranteed: 260 o c/10 seconds/.375?,(9.5mm) lead lengths at 5 lbs., (2.3kg) tension mounting position: any weight: 1.1 grams do-201ad dimensions in inches and (millimeters) maximum ratings and el ectrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol sf 31g sf 32g sf 33g sf 34g sf 35g sf 36g sf 37g sf 38g units maximum recurrent peak reverse voltage v rrm 50 100 150 200 300 400 500 600 v maximum rms voltage v rms 35 70 105 140 210 280 350 420 v maximum dc blocking voltage v dc 50 100 150 200 300 400 500 600 v maximum average forward rectified current .375 (9.5mm) lead length @t a = 55 i (av) 3.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 125 a maximum instantaneous forward voltage @ 3.0a v f 0.95 1.3 1.7 v maximum dc reverse current @ t a =25 at rated dc blocking voltage @ t a =125 i r 5.0 100 ua ua maximum reverse recovery time (note 1) trr 35 ns typical junction capacitance (note 2) cj 80 60 pf typical thermal resistance (note 3) r ja r jl 35 10 /w operating temperature range t j -65 to +150 storage temperature range t stg -65 to +150 notes: 1. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a 2. measured at 1 mhz and applied reverse voltage of 4.0 v d.c. 3. mount on cu-pad size 16mm x 16mm on pcb.
- 197 - ratings and characteristic curves (sf31g thru sf38g) fig.5- maximum non-repetitive forward surge current peak for ward surge current . (a) 1 2 5 10 20 100 50 25 0 50 75 100 125 150 175 number of cycles at 60hz 8.3ms single half sine wave jedec method fig.4- typical forward characteristics fig.3- typical reverse characteristics instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 .01 1.0 0.1 10 100 1000 percent of rated peak reverse voltage. (%) tj=25 c 0 tj=125 c 0 tj=150 c 0 fig.6- typical junction capacitance junction cap acitance.(pf) .1 .5 1 5 2 10 20 50 100 200 500 1000 40 20 60 80 100 120 140 reverse voltage. (v) sf31g~sf34g sf35g~sf38g tj=25 c 0 fig.2- maximum average forward current derating fig.1- reverse recovery time characteristic and test circuit diagram average for ward current . (a) 50 noninductive non inductive oscilloscope (note 1) pulse generator (note 2) dut (+) 50vdc (approx) (-) notes: 1. rise time=7ns max. input impedance= 1 megohm 22pf 2. rise time=10ns max. sourse impedance= 50 ohms (-) (+) 10 noninductive -1.0a -0.25a 0 +0.5a trr 1cm set time base for 5/ 10ns/ cm 25 50 75 100 125 150 175 1.0 0.5 1.5 2.5 2.0 3.0 ambient temperature. ( c) o single phase half wave 60hz resistive or inductive load 0.375" (9.5mm) lead length instantaneous for ward current . (a) 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 .01 0.1 1.0 10.0 100.0 forward voltage. (v) tj=25 c pulse width=300 s 1% duty cycle o sf31g~sf34g sf35g~sf36g SF37G~sf38g 0
|
