________________________________________________________________________ http://www.union-ic.com rev.01 dec.2012 1/5 UM5052DA single line bi-directional esd protection diode array UM5052DA dfn2 0.6 0.3 general description the UM5052DA esd protection diode is designed to replace multilayer varistors (mlvs) in portable applications such as cell phones, noteboo k computers, and pda?s. they offer desirable electrical characteristics for board level protection, such as fast response time, lower operating voltage, lower clamping voltage and no device degradation when compared to mlvs. the UM5052DA esd protection diode protects sensitiv e semiconductor components from damage or upset due to electrostatic discharge (esd) a nd other voltage induced transient events. the UM5052DA is available in dfn2 0.6mm0.3mm packag e with working voltage of 5 volt. it gives designer the flexibility to protect one bidirectional line in applications where arrays are not practical. additionally, it may be ?sprinkled? aroun d the board in applications where board space is at a premium. it may be used to meet th e esd immunity requirements of iec 61000-4-2, 30kv air, 30kv contact discharge. applications features z cell phone handsets and accessories z personal digital assistants (pda?s) z notebooks, desktops and servers z portable instrumentation z cordless phones z digital cameras z peripherals z mp3 players z transient protection for data lines to iec 61000-4-2 (esd) 30kv (air), 30kv (contact) z small package for use in portable electronics z suitable replacement for mlv?s in esd protection applications z protect one i/o or power line z low clamping voltage z stand off voltages: 5v z low leakage current z solid-state silicon-avalanche technology pin configurations top view UM5052DA dfn2 0.6 0.3
________________________________________________________________________ http://www.union-ic.com rev.01 dec.2012 2/5 UM5052DA ordering information part number working voltage packaging type channel marking code shipping qty UM5052DA 5.0v dfn2 0.60.3mm 2 1 f 8000pcs/7 inch tape & reel absolute maximum ratings rating symbol value units peak pulse power (tp = 8/20 s) p pk 60 watts maximum peak pulse current (t=8/20 s) i pp 5 amps lead soldering temperature t l 260 (10 sec.) c operating temperature t j -55 to +125 c storage temperature t stg -55 to +150 c symbol definition parameter symbol maximum reverse peak pulse current i pp clamping voltage @ i pp v c working peak reverse voltage v rwm maximum reverse leakage current @ v rwm i r breakdown voltage @ i t v br test current i t forward current i f forward voltage @ i f v f peak power dissipation p pk max. capacitance @ v r = 0v, f = 1mhz c
________________________________________________________________________ http://www.union-ic.com rev.01 dec.2012 3/5 UM5052DA electrical characteristics (t=25c, device for 5.0v reverse stand-off voltage) parameter symbol conditions min typ max unit reverse stand-off voltage v rwm 5 v reverse breakdown voltage v br it = 1ma 6.5 8.0 8.5 v reverse leakage current i r v rwm = 5v, t=25c 1 a clamping voltage v c i pp = 5a, t p = 8/20 s 12 v junction capacitance c j v r = 0v, f = 1mhz 7 10 pf junction capacitance c j v r = 2.5v, f = 1mhz 6 9 pf applications information device connection options UM5052DA esd protection diode is designed to prot ect one bidirectional data, i/o, or power supply line from the damage caused by esd and su rge pluses. the device is bidirectional and can be used on lines where the signal polarity is above ground and below ground. circuit board layout recommendations for suppression of esd good circuit board layout is critical for the s uppression of esd induced transients. the following guidelines are recommended: 1) place the tvs near the input terminals or conn ectors to restrict transient coupling. 2) minimize the path length between the tvs and the protected line. 3) minimize all conductive loops including power and ground loops. 4) the esd transient return path to ground should be kept as short as possible. 5) never run critical signals near board edges. 6) use ground planes whenever possible. for mu ltilayer printed-circuit boards, use ground vias. 7) keep parallel signal paths to a minimum. 8) avoid running protection conductors in parallel with unprotected conductor. 9) minimize all printed-circuit board conductiv e loops including power and ground loops. 10) avoid using shared transient return paths to a common ground point.
________________________________________________________________________ http://www.union-ic.com rev.01 dec.2012 4/5 UM5052DA package information UM5052DA dfn2 0.60.3 outline drawing dimensions millimeters symbol min typ max a 0.595 0.620 0.645 b 0.295 0.320 0.345 c 0.245 0.275 0.305 d 0.145 0.150 0.155 e 0.245 0.250 0.255 f 0.245 0.250 0.255 g 0.005 0.010 0.015 land pattern notes: 1. compound dimension: 0.60.3; 2. unit: mm; 3. general tolerance 0.025mm unless otherwise specified; 4. the layout is just for reference. tape and reel orientation
________________________________________________________________________ http://www.union-ic.com rev.01 dec.2012 5/5 UM5052DA important notice the information in this document has been ca refully reviewed and is believed to be accurate. nonetheless, this document is subjec t to change without notice. union assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the contained information, or to notify a person or organization of any update. union rese rves the right to make changes, at any time, in order to improve reliability, function or design and to attempt to supply the best product possible. union semiconductor, inc add: 2f, no. 3, lane 647 songtao road, shanghai 201203 tel: 021-51093966 fax: 021-51026018 website: www.union-ic.com
|
