www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com key features: ? 2w output power ? miniature sip case ? short circuit protected ? 1,500 vdc isolation ? 57 standard models ? single and dual outputs ? >3.5 mhour mtbf ? -40c to +105c operation ? low cost md200xe low cost, 2w miniature sip dc/dc con vert ers input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.50 5.0 5.50 vdc 9 vdc input 8.10 9.0 9.90 12 vdc input 10.80 12.0 13.20 15 vdc input 13.50 15.0 16.50 24 vdc input 21.60 24.0 26.40 input filter internal capacitor output parameter conditions min. typ. max. units output voltage accuracy ?.5 % line regulation 3.3 vdc output for v in change of 1% ?.5 % all other outputs ?.2 load regulation, see note 1 see model selection guide ripple & noise (20 mhz), see note 2 output voltage <12 vdc 60 mv p - p 15 vdc, 24 vdc output 75 temperature coef cient ?.03 %/? output short circuit continuous (autorecovery) general parameter conditions min. typ. max. units isolation voltage 60 seconds 1,500 vdc isolation resistance 500 vdc 1,000 m ? isolation capacitance 100 khz, 1v 20 pf switching frequency 100 300 khz emi characteristics parameter conditions min. typ. max. units emi compliance, see note 4 conducted cispr22/en 55022 level b radiated cispr22/en 55022 level b emc compliance, single output electrostatic discharge (esd) en 61000-4-2 level b contact ? kv emc compliance, dual output en 61000-4-2 level b contact ? kv environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +105 ? storage temperature range -55 +125 ? cooling free air convection humidity rh, non-condensing 95 % physical case size 0.772 x 0.276 x 0.394 inches (19.6 x 7.0 x 10.0 mm) case material non-conductive black plastic (ul-94v0) weight 0.08 oz (2.4g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25?, gnd benign 3.5 mhours absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (1 sec) 5 vdc input -0.7 9.0 vdc 9 vdc input -0.7 12.0 12 vdc input -0.7 18.0 15 vdc input -0.7 21.0 24 vdc input -0.7 30.0 lead temperature 1.5 mm from case for 10 sec 300 ? caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. series electrical speci? cations speci cations typical @ +25?, nominal input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. 3.0 kv isolation models available
292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com www.micropowerdirect.com model selection guide w ww.m i cropower di rect.co m www.micropowerdirect.com model number input output load regulation output capacitive load ( f max) ef? ciency (%) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load % typ. min. typ. md205s-03e 5 4.5 - 5.5 476 25 3.3 400 40.0 18.0 220 70 74 1,000 md205s-05e 5 4.5 - 5.5 506 25 5.0 400 40.0 12.0 220 75 79 1,000 md205s-09e 5 4.5 - 5.5 506 25 9.0 222 22.0 9.0 220 77 81 1,000 md205s-12e 5 4.5 - 5.5 476 25 12.0 167 17.0 8.0 220 80 84 1,000 md205s-15e 5 4.5 - 5.5 476 25 15.0 133 13.0 7.0 220 80 84 1,000 md205s-24e 5 4.5 - 5.5 476 25 24.0 83 8.0 6.0 220 80 84 1,000 md205d-03e 5 4.5 - 5.5 540 25 ?.3 ?03 ?0.0 18.0 100 70 74 1,000 md205d-05e 5 4.5 - 5.5 500 25 ?.0 ?00 ?0.0 12.0 100 76 80 1,000 md205d-09e 5 4.5 - 5.5 476 25 ?.0 ?11 ?1.0 9.0 100 80 84 1,000 md205d-12e 5 4.5 - 5.5 476 25 ?2.0 ?3 ?.0 8.0 100 80 84 1,000 md205d-15e 5 4.5 - 5.5 476 25 ?5.0 ?7 ?.0 7.0 100 80 84 1,000 md205d-24e 5 4.5 - 5.5 476 25 ?4.0 ?2 ?.0 6.0 100 80 84 1,000 md209s-05e 9 8.1 - 9.9 285 20 5.0 400 40.0 12.0 220 76 80 750 md209s-09e 9 8.1 - 9.9 281 20 9.0 222 22.0 9.0 220 77 81 750 md209s-12e 9 8.1 - 9.9 274 20 12.0 167 17.0 8.0 220 79 83 750 md209s-15e 9 8.1 - 9.9 274 20 15.0 133 13.0 7.0 220 79 83 750 md209s-24e 9 8.1 - 9.9 274 20 24.0 83 8.0 6.0 220 79 83 750 md209d-05e 9 8.1 - 9.9 285 20 ?.0 ?00 ?0.0 12.0 100 76 80 750 md209d-09e 9 8.1 - 9.9 281 20 ?.0 ?11 ?1.0 9.0 100 77 81 750 md209d-12e 9 8.1 - 9.9 274 20 ?2.0 ?3 ?.0 8.0 100 79 83 750 md209d-15e 9 8.1 - 9.9 274 20 ?5.0 ?7 ?.0 7.0 100 79 83 750 md209d-24e 9 8.1 - 9.9 274 20 ?4.0 ?2 ?.0 6.0 100 79 83 750 md212s-03e 12 10.8 - 13.2 198 15 3.3 400 40.0 18.0 220 75 79 500 md212s-05e 12 10.8 - 13.2 213 15 5.0 400 40.0 12.0 220 86 80 500 md212s-09e 12 10.8 - 13.2 211 15 9.0 222 22.0 9.0 220 77 81 500 md212s-12e 12 10.8 - 13.2 198 15 12.0 167 17.0 8.0 220 80 84 500 md212s-15e 12 10.8 - 13.2 198 15 15.0 133 13.0 7.0 220 80 84 500 md212s-15e 12 10.8 - 13.2 198 15 24.0 83 8.0 6.0 220 81 85 500 md212d-03e 12 10.8 - 13.2 208 15 ?.3 ?03 ?0.0 18.0 100 76 80 500 md212d-05e 12 10.8 - 13.2 198 15 ?.0 ?00 ?0.0 12.0 100 80 84 500 md212d-07e 12 10.8 - 13.2 198 15 ?.2 ?39 ?4.0 10.0 100 80 84 500 md212d-09e 12 10.8 - 13.2 205 15 ?.0 ?11 ?1.0 9.0 100 79 83 500 md212d-12e 12 10.8 - 13.2 196 15 ?2.0 ?3 ?.0 8.0 100 81 85 500 md212d-15e 12 10.8 - 13.2 198 15 ?5.0 ?7 ?.0 7.0 100 80 84 500 md212d-24e 12 10.8 - 13.2 196 15 ?4.0 ?2 ?.0 6.0 100 82 86 500 md215s-05e 15 13.5 - 16.5 171 10 5.0 400 40.0 12.0 220 76 80 400 md215s-09e 15 13.5 - 16.5 169 10 9.0 222 22.0 9.0 220 77 81 400 md215s-12e 15 13.5 - 16.5 159 10 12.0 167 17.0 8.0 220 80 84 400 md215s-15e 15 13.5 - 16.5 157 10 15.0 133 13.0 7.0 220 80 84 400 md215s-24e 15 13.5 - 16.5 157 10 24.0 83 8.0 6.0 220 81 85 400 md215d-05e 15 13.5 - 16.5 167 10 ?.0 ?00 ?0.0 12.0 100 76 80 400 md215d-09e 15 13.5 - 16.5 167 10 ?.0 ?11 ?1.0 9.0 100 76 80 400 md215d-12e 15 13.5 - 16.5 159 10 ?2.0 ?3 ?.0 8.0 100 80 84 400 md215d-15e 15 13.5 - 16.5 157 10 ?5.0 ?7 ?.0 7.0 100 81 85 400 md215d-24e 15 13.5 - 16.5 157 10 ?4.0 ?2 ?.0 6.0 100 81 85 400 md224s-03e 24 21.6 - 26.4 99 8 3.3 400 40.0 18.0 220 75 79 250 md224s-05e 24 21.6 - 26.4 104 8 5.0 400 40.0 12.0 220 76 80 250 md224s-09e 24 21.6 - 26.4 100 8 9.0 222 22.0 9.0 220 79 83 250 md224s-12e 24 21.6 - 26.4 99 8 12.0 167 17.0 8.0 220 80 84 250 md224s-15e 24 21.6 - 26.4 99 8 15.0 133 13.0 7.0 220 80 84 250 md224s-24e 24 21.6 - 26.4 98 8 24.0 83 8.0 6.0 220 80 84 250 md224d-03e 24 21.6 - 26.4 104 8 ?.3 ?03 ?0.0 18.0 100 76 80 250 md224d-05e 24 21.6 - 26.4 99 8 ?.0 ?00 ?0.0 12.0 100 80 84 250 md224d-09e 24 21.6 - 26.4 98 8 ?.0 ?11 ?1.0 9.0 100 81 85 250 md224d-12e 24 21.6 - 26.4 99 8 ?2.0 ?3 ?.0 8.0 100 80 84 250 md224d-15e 24 21.6 - 26.4 99 8 ?5.0 ?7 ?.0 7.0 100 80 84 250 md224d-24e 24 21.6 - 26.4 98 8 ?4.0 ?2 ?.0 6.0 100 81 85 250 notes: 1. output load regulation is speci ed for a load change of 10% to 100%. 2. when measuring output ripple, it is recommended that an external 1 f ceramic capacitor & 10 f electrolytic capacitor be placed in parallel from the +vout pin to the -vout pin for single output models, or from each output to common for dual output models. 3. operation at no load will not damage these units, however, they may not meet all speci cations. 4. these converters are speci ed for operation without external components. however, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. the simple connection shown on page 3 will typically meet en 55022 class b. for dual output units, a capacitor should be connected from each output to common. derating curve
micropower direct 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com www.micropowerdirect.com typical connection , single output models v in c 1 l 1 3.3 vdc 4.7 f/50v 6.8 h 5 vdc 4.7 f/50v 6.8 h 12 vdc 4.7 f/50v 6.8 h 15 vdc 4.7 f/50v 6.8 h 24 vdc 4.7 f/50v 6.8 h v out c 2 c 3 3.3 vdc 10 f 10 f 5.0 vdc 10 f 10 f 9.0 vdc 2.2 f 2.2 f 12 vdc 2.2 f 2.2 f 15 vdc 1.0 f 1.0 f 24 vdc 1.0 f 1.0 f ?.3 vdc 4.7 f 4.7 f 5.0 vdc 4.7 f 4.7 f ?.0 vdc 1.0 f 1.0 f ?2 vdc 1.0 f 1.0 f ? 5 vdc 0.47 f 0.47 f ?4 vdc 0.47 f 0.47 f these converters are speci ed for operation without external components. however, in some applications the addition of input/ output capacitors will enhance stability and reduce output ripple. for applications that require meeting emc standards, the diagrams above illust rates a typical connection of the md200x-xxe series. suggested component values are given in the table at right. capacitors c 2 and c 3 are not required to meet speci cations, but may be used if a lower level of output ripple is required. typical connection , dual output models typical ef? ciency vs input , 5 v in models typical ef? ciency vs input , 12 v in models typical ef? ciency vs output , 5 v in models typical ef? ciency vs output , 12 v in models ef ciency vs input is plotted with the unit at full load. ef ciency vs output is plotted with the unit at nominal input.
micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com www.micropowerdirect.com w ww.m i cropower di rect.co m www.micropowerdirect.com notes: all dimensions are typical in inches (mm) general tolerance x.xx = ?.02 (?.5) pin 1 is marked by a ?ot or indentation on the unit mechanical dimensions typical board layout , single output models pin single output 1+v in 2-v in 4-v out 5 no pin 6+v out pin dual output 1+v in 2-v in 4-v out 5 common 6+v out pin con nec tions typical board layout , dual output models the drawings below show typical board layouts for the emc circuits shown on page three (one for single output models and one for dual output units).
|
