2009/10 edition magnetic components selector guide we reserve the right to change specifications without prior notice. www.bitechnologies.com 87 inductance 100khz, 0.1v dcr (1) i sat (2) heating (3) core loss (4) @ 0 adc @ i sat (m w ) @ 25c current factor part ( h 20%) ( h) (adc) (adc) number typ. min. typ. typ. max. ? t=50c k1 k2 fig. hm70-101r0lf 1.00 0.63 0.70 2.53 2.90 16 15 9.07e-11 170.67 1 hm70-201r3lf 1.33 0.93 1.16 3.38 3.74 16 13 1.24e-10 157.15 1 hm70-201r9lf 1.94 1.28 1.60 4.71 5.42 12 11 1.24e-10 189.83 1 hm70-25r80lf 0.83 0.488 0.61 1.75 2.01 18 19 1.51e-10 118.84 1 hm70-301r5lf 1.50 0.80 1.00 2.16 2.48 16 17 1.40e-10 183.07 1 hm70-302r0lf 2.10 1.12 1.40 3.48 4.00 12 14 1.53e-10 196.09 1 hm70-31r65lf 0.65 0.48 0.54 1.80 2.50 16 19 1.53e-10 60.69 1 hm70-311r0lf 1.00 0.60 0.90 2.16 2.48 16 17 1.53e-10 93.38 1 hm70-321r3lf 1.30 0.80 1.00 2.16 2.48 16 17 1.66e-10 140.35 1 hm70-33r75lf 0.75 0.50 0.61 1.40 1.50 16 22 1.53e-10 70.03 1 hm70-341r3lf 1.30 0.80 1.00 2.16 2.48 20 18 1.53e-10 121.39 1 hm70-351r5lf 1.50 0.97 1.20 4.00 4.50 18 13 1.35e-10 166.20 2 hm70-401r2lf 1.20 0.92 1.02 1.75 1.80 18 22 1.80e-10 129.45 2 hm70-401r6lf 1.60 1.15 1.44 2.13 2.36 20 20 1.67e-10 151.67 2 hm70-431r9lf 1.90 1.50 1.70 2.00 2.20 15 20 1.67e-10 172.04 2 hm70-455r6lf 5.60 4.45 5.00 5.00 6.00 8 13 1.67e-10 507.07 2 hm70-50r70lf 0.70 0.40 0.52 1.05 1.26 30 31 1.99e-10 88.15 2 hm70-501r2lf 1.20 0.80 0.90 1.68 2.00 24 25 1.99e-10 110.82 2 hm70-505r0lf 5.00 3.60 4.30 6.50 8.00 7 13 2.21e-10 219.63 2 hm70-50100lf 10.0 6.80 8.00 12.0 15.0 7 9 2.21e-10 316.67 2 hm70-601r2lf 1.20 0.80 1.00 1.37 1.58 20 28 2.21e-10 108.94 2 hm70-602r0lf 2.00 1.20 1.60 2.20 2.60 15 22 2.21e-10 143.34 2 ? operating temperature range -40c to +180c ? temperature rise, maximum 5 0c ? operating frequency up to 400khz hm70 electrical / environmental high power shielded low profile surface mount inductors notes: (1) dc resistance is measured at 25c. (2) the saturation current (i sat ) is the current at which the inductance will be decreased by 20% from its initial (zero dc) value. (3) the heating current is the dc current, which causes the component temperature to increase by approximately 50c. this current is determined by soldering the component on a typical application pcb, and then applying the current to the device for 30 minutes. (4) core loss approximation is based on published core data: core loss (pfe) = k1 * (f) 1.338 * (k2 ? i) 2.2546 where: core loss in watt f = frequency in khz k1 and k2 = core loss factor ? i = delta i across the component in amp. k2 ? i = one half of the peak to peak flux density across the component in gauss specifications rohs compliant packaging standard : embossed tape & reel reel: diameter: = 13 (330.2mm) capacity: case size 10,20,25,30,31,32,33,34 = 500 units case size 35,40,43,45,50,60 = 400 units
www.bitechnologies.com magnetic components selector guide 2009/10 edition we reserve the right to change specifications without prior notice. 88 electrical characteristics @ 25 c (b) case size 50 & 60 (a) case size 10, 20, 25, 30 & 40 inductance vs. current characteristics inductance vs. current characteristics inductance rolloffvs. current characteristics inductance rolloffvs. current characteristics
2009/10 edition magnetic components selector guide we reserve the right to change specifications without prior notice. www.bitechnologies.com 89 case size a b c d e f g h i j k 10 9.00 10.5 3.70 4.80 1.70 6.00 8.30 2.30 6.00 2.80 3.00 20 9.00 10.5 4.50 4.80 1.70 6.00 8.00 2.00 6.00 2.80 3.00 25 9.00 10.5 5.00 4.80 1.70 6.00 8.30 2.30 6.00 2.80 3.00 30 9.00 10.5 5.35 4.80 1.70 6.00 8.00 2.00 6.00 2.80 3.00 31 9.00 10.5 5.40 4.80 1.70 6.00 8.00 2.00 6.00 2.80 3.00 32 9.00 10.5 5.60 4.80 1.70 6.00 8.00 2.00 6.00 2.80 3.00 33 9.00 10.5 5.70 4.80 1.70 6.00 8.00 2.00 6.00 2.80 3.00 34 9.00 10.5 5.80 4.80 1.70 6.00 8.00 2.00 6.00 2.80 3.00 35 10.7 10.25 4.20 5.60 1.70 6.00 10.60 5.60 6.20 2.10 2.50 40 11.0 12.6 5.20 6.20 2.30 7.50 10.70 3.70 7.50 3.10 3.50 43 10.1 12.5 5.75 4.77 2.30 7.32 10.31 4.17 7.32 2.95 2.84 45 10.1 12.5 6.60 4.60 2.30 7.32 10.31 4.00 7.32 2.74 3.15 50 13.5 12.9 5.50 6.50 2.30 7.50 13.50 6.50 7.50 3.00 3.50 60 14.0 13.0 5.80 6.50 2.30 7.50 14.00 6.50 7.50 3.00 3.50 ordering information inductance code: first 2 digits are signifcant. last digit denotes the number of trailing zeros. for values below 10h, r denotes the decimal point. case size model series tr - tape & reel packing 13 - 13 reel hm70 - 50 1r2 lf tr13 lead-free outline dimensions (mm) recommended solder pad layout top view bottom view figure 1 figure 2 top view bottom view note: (1) dummy terminal should not be used for any electrical connection.
|