View AD9577-EVALZ_7449643.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

clock generator with dual plls, spread spectrum, and margining data sheet ad9577 rev. 0 information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2011 analog devices, inc. all rights reserved. features fully integrated dual pll/vco cores 1 integer-n and 1 fractional-n pll continuous frequency coverage from 11.2 mhz to 200 mhz most frequencies from 200 mhz to 637.5 mhz available pll1 phase jitter (12 khz to 20 mhz): 460 fs rms typical pll2 phase jitter (12 khz to 20 mhz) integer-n mode: 470 fs rms typical fractional-n mode: 660 fs rms typical input crystal or reference clock frequency optional reference frequency divide-by-2 i 2 c programmable output frequencies up to 4 lvds/lvpecl or up to 8 lvcmos output clocks 1 cmos buffered reference clock output spread spectrum: downspread [0, ?0.5]% 2 pin-controlled frequency maps: margining integrated loop filters space saving, 6 mm 6 mm, 40-lead lfcsp package 1.02 w power dissipation (lvds operation) 1.235 w power dissipation (lvpecl operation) 3.3 v operation applications low jitter, low phase noise multioutput clock generator for data communications applications including ethernet, fibre channel, sonet, sdh, pci-e, sata, ptn, otn, adc/dac, and digital video spread spectrum clocking general description the ad9577 provides a multioutput clock generator function, along with two on-chip phase-locked loop cores, pll1 and pll2, optimized for network clocking applications. the pll designs are based on the analog devices, inc., proven portfolio of high performance, low jitter frequency synthesizers to maximize network performance. the plls have i 2 c programmable output frequencies and formats. the fractional-n pll can support spread spectrum clocking for reduced emi radiated peak power. both plls can support frequency margining. other applications with demanding phase noise and jitter requirements can benefit from this part. the first integer-n pll section (pll1 ) consists of a low noise phase frequency detector (pfd), a precision charge pump (cp), a low phase noise voltage controlled oscillator (vco), a programmable functional block diagram xtal osc refclk xt1 xt2 margin refsel cmos ad9577 divide 1 or 2 vco 2.15ghz to 2.55ghz pfd/cp third order lpf ldo feedback divider lvpecl/lvds refout or 2 cmos dividers lvpecl/lvds or 2 cmos dividers f pfd pll1 vco 2.15ghz to 2.55ghz pfd/cp third order lpf ldo feedback divider lvpecl/lvds or 2 cmos dividers lvpecl/lvds or 2 cmos dividers pll2 scl sda i 2 c control sscg max_bw spread spectrum, sdm 09284-001 figure 1. feedback divider, and two independently programmable output dividers. by connecting an external crystal or applying a reference clock to the refclk pin, frequencies of up to 637.5 mhz can be synchronized to the input reference. each output divider and feedback divider ratio is i 2 c programmed for the required output rates. a second fractional-n pll (pll2) with a programmable modulus allows vco frequencies that are fractional multiples of the reference frequency to be synthesized. each output divider and feedback divider ratio can be programmed for the required output rates, up to 637.5 mhz. this fractional-n pll can also operate in integer-n mode for the lowest jitter. up to four differential output clock signals can be configured as either lvpecl or lvds signaling formats. alternatively, the outputs can be configured for up to eight cmos outputs. combinations of these formats are supported. no external loop filter components are required, thus conserving valuable design time and board space. the ad9577 is available in a 40-lead, 6 mm 6 mm lfcsp package and can operate from a single 3.3 v supply. the operating temperature range is ?40c to +85c.
ad9577 data sheet rev. 0 | page 2 of 44 table of contents features .............................................................................................. 1 ? applications....................................................................................... 1 ? general description ......................................................................... 1 ? functional block diagram .............................................................. 1 ? revision history ............................................................................... 2 ? specifications..................................................................................... 3 ? pll1 characteristics .................................................................... 3 ? pll1 clock output jitter............................................................. 5 ? pll2 fractional-n mode characteristics ................................. 6 ? pll2 integer-n mode characteristics....................................... 7 ? pll2 clock output jitter............................................................. 9 ? cmos reference clock output jitter...................................... 11 ? timing characteristics .............................................................. 12 ? clock outputs ............................................................................. 13 ? power............................................................................................ 14 ? crystal oscillator........................................................................ 15 ? reference input........................................................................... 15 ? control pins ................................................................................ 15 ? absolute maximum ratings.......................................................... 16 ? thermal characteristics ............................................................ 16 ? esd caution................................................................................ 16 ? pin configuration and function descriptions........................... 17 ? typical performance characteristics ........................................... 19 ? refout and pll1 phase noise performance ...................... 19 ? pll2 phase noise performance................................................ 20 ? output jitter ................................................................................ 21 ? typical output signal ................................................................ 22 ? typical spread spectrum performance characteristics ........ 24 ? terminology .................................................................................... 25 ? detailed block diagram ................................................................ 27 ? example application.................................................................. 28 ? functional description.................................................................. 29 ? reference input and reference dividers................................. 29 ? output channel dividers.......................................................... 30 ? outputs ........................................................................................ 30 ? reference output buffer ........................................................... 31 ? pll1 integer-n pll................................................................... 31 ? pll1 phase frequency detector (pfd) and charge pump . 32 ? pll1 vco ................................................................................... 32 ? pll1 feedback divider ............................................................. 32 ? setting the output frequency of pll1.................................... 32 ? pll2 integer/fractional-n pll ............................................... 32 ? pll2 phase frequency detector (pfd) and charge pump . 33 ? pll2 loop bandwidth............................................................... 33 ? pll2 vco ................................................................................... 33 ? pll2 feedback divider ............................................................. 33 ? pll2 - modulator ................................................................. 33 ? spur mechanisms ....................................................................... 33 ? optimizing pll performance .................................................. 34 ? setting the output frequency of pll2.................................... 34 ? margining .................................................................................... 35 ? spread spectrum clock generation (sscg).......................... 35 ? i 2 c interface timing and internal register description........... 38 ? default frequency map and output formats ........................ 40 ? i 2 c interface operation ............................................................. 40 ? typical application circuits ..................................................... 42 ? power and grounding considerations and power supply rejection...................................................................................... 43 ? outline dimensions ....................................................................... 44 ? ordering guide .......................................................................... 44 ? revision history 10/11revision 0: initial version
data sheet ad9577 rev. 0 | page 3 of 44 specifications typical (typ) is given for v s = 3.3 v, t a = 25c, unless otherwise noted. minimum (min) and maximum (max) values are given over full v s (3.0 v to 3.6 v) and t a (?40c to +85c) variation. ac coupling capacitors of 0.1 f used where appropriate. a fox electronics fx532a 25 mhz crystal is used throughout, unless otherwise stated. pll1 characteristics table 1. parameter min typ max unit test conditions/comments 1 noise characteristics phase noise (106.25 mhz lvpecl output) na = 102, vx = 4, dx = 6, f pfd = 25 mhz at 1 khz ?121 dbc/hz at 10 khz ?127 dbc/hz at 100 khz ?128 dbc/hz at 1 mhz ?150 dbc/hz at 10 mhz ?156 dbc/hz at 30 mhz ?158 dbc/hz phase noise (156.25 mhz lvpecl output) na = 100, vx = 4, dx = 4, f pfd = 25 mhz at 1 khz ?117 dbc/hz at 10 khz ?124 dbc/hz at 100 khz ?124 dbc/hz at 1 mhz ?147 dbc/hz at 10 mhz ?156 dbc/hz at 30 mhz ?156 dbc/hz phase noise (625 mhz lvpecl output) na = 100, vx = 2, dx = 2, f pfd = 25 mhz at 1 khz ?105 dbc/hz at 10 khz ?112 dbc/hz at 100 khz ?112 dbc/hz at 1 mhz ?135 dbc/hz at 10 mhz ?150 dbc/hz at 30 mhz ?150 dbc/hz phase noise (106.25 mhz lvds output) na = 102, vx = 4, dx = 6, f pfd = 25 mhz at 1 khz ?119 dbc/hz at 10 khz ?127 dbc/hz at 100 khz ?128 dbc/hz at 1 mhz ?148 dbc/hz at 10 mhz ?156 dbc/hz at 30 mhz ?156 dbc/hz phase noise (156.25 mhz lvds output) na = 100, vx = 4, dx = 4, f pfd = 25 mhz at 1 khz ?116 dbc/hz at 10 khz ?124 dbc/hz at 100 khz ?124 dbc/hz at 1 mhz ?145 dbc/hz at 10 mhz ?155 dbc/hz at 30 mhz ?155 dbc/hz phase noise (625 mhz lvds output) na = 100, vx = 2, dx = 2, f pfd = 25 mhz at 1 khz ?104 dbc/hz at 10 khz ?111 dbc/hz at 100 khz ?112 dbc/hz at 1 mhz ?134 dbc/hz at 10 mhz ?149 dbc/hz at 30 mhz ?149 dbc/hz
ad9577 data sheet rev. 0 | page 4 of 44 parameter min typ max unit test conditions/comments 1 phase noise (106.25 mhz cmos output) na = 102, vx = 4, dx = 6, f pfd = 25 mhz at 1 khz ?118 dbc/hz at 10 khz ?127 dbc/hz at 100 khz ?127 dbc/hz at 1 mhz ?149 dbc/hz at 10 mhz ?156 dbc/hz at 30 mhz ?157 dbc/hz phase noise (156.25 mhz cmos output) na = 100, vx = 4, dx = 4, f pfd = 25 mhz at 1 khz ?115 dbc/hz at 10 khz ?124 dbc/hz at 100 khz ?124 dbc/hz at 1 mhz ?146 dbc/hz at 10 mhz ?155 dbc/hz at 30 mhz ?155 dbc/hz phase noise (155.52 mhz lvpecl output) na = 112, vx = 2, dx = 7, f pfd = 19.44 mhz at 1 khz ?117 dbc/hz at 10 khz ?122 dbc/hz at 100 khz ?123 dbc/hz at 1 mhz ?148 dbc/hz at 10 mhz ?156 dbc/hz at 30 mhz ?156 dbc/hz phase noise (622.08 mhz lvpecl output) na = 128, vx = 2, dx = 2, f pfd = 19.44 mhz at 1 khz ?105 dbc/hz at 10 khz ?110 dbc/hz at 100 khz ?110 dbc/hz at 1 mhz ?136 dbc/hz at 10 mhz ?150 dbc/hz at 30 mhz ?150 dbc/hz phase noise (155.52 mhz lvds output) na = 112, vx = 2, dx = 7, f pfd = 19.44 mhz at 1 khz ?117 dbc/hz at 10 khz ?122 dbc/hz at 100 khz ?123 dbc/hz at 1 mhz ?146 dbc/hz at 10 mhz ?155 dbc/hz at 30 mhz ?155 dbc/hz phase noise (622.08 mhz lvds output) na = 128, vx = 2, dx = 2, f pfd = 19.44 mhz at 1 khz ?105 dbc/hz at 10 khz ?110 dbc/hz at 100 khz ?110 dbc/hz at 1 mhz ?134 dbc/hz at 10 mhz ?149 dbc/hz at 30 mhz ?150 dbc/hz phase noise (155.52 mhz cmos output) na = 112, vx = 2, dx = 7, f pfd = 19.44 mhz at 1 khz ?117 dbc/hz at 10 khz ?122 dbc/hz at 100 khz ?123 dbc/hz at 1 mhz ?147 dbc/hz at 10 mhz ?155 dbc/hz at 30 mhz ?155 dbc/hz 1 x indicates either 0 or 1 for any given test condition.
data sheet ad9577 rev. 0 | page 5 of 44 pll1 clock output jitter table 2. parameter 1 min typ max unit test conditions/comments 2 lvpecl integrated random phase jitter 25 mhz crystal used rms jitter (625 mhz output) 460 750 fs rms 12 khz to 20 mhz, na = 100, vx = 2, dx = 2 430 650 fs rms 50 khz to 80 mhz, na = 100, vx = 2, dx = 2 rms jitter (156.25 mhz output) 460 750 fs rms 12 khz to 20 mhz, na = 100, vx = 4, dx = 4 rms jitter (106.25 mhz output) 460 750 fs rms 12 khz to 20 mhz, na = 102, vx = 4, dx = 6 lvds integrated random phase jitter 25 mhz crystal used rms jitter (625 mhz output) 470 820 fs rms 12 khz to 20 mhz, na = 100, vx = 2, dx = 2 450 790 fs rms 50 khz to 80 mhz, na = 100, vx = 2, dx = 2 rms jitter (156.25 mhz output) 470 790 fs rms 12 khz to 20 mhz, na = 100, vx = 4, dx = 4 rms jitter (106.25 mhz output) 470 790 fs rms 12 khz to 20 mhz, na = 102, vx = 4, dx = 6 cmos integrated random phase jitter 25 mhz crystal used, 50 load rms jitter (100 mhz output) 470 920 f s rms 12 khz to 20 mhz, na = 96, vx = 4, dx = 6 rms jitter (33.3 mhz output) 420 700 f s rms 12 khz to 5 mhz, na = 88, vx = 6, dx = 11 lvpecl integrated random phase jitter 19.44 mhz crystal used rms jitter (622.08 mhz output) 500 680 fs rms 12 khz to 20 mhz, na = 128, vx = 2, dx = 2 460 590 fs rms 50 khz to 80 mhz, na = 128, vx = 2, dx = 2 rms jitter (155.52 mhz output) 480 680 fs rms 12 khz to 20 mhz, na = 112, vx = 2, dx = 7 lvds integrated random phase jitter 19.44 mhz crystal used rms jitter (622.08 mhz output) 520 780 fs rms 12 khz to 20 mhz, na = 128, vx = 2, dx = 2 480 710 fs rms 50 khz to 80 mhz, na = 128, vx = 2, dx = 2 rms jitter (155.52 mhz output) 480 750 fs rms 12 khz to 20 mhz, na = 112, vx = 2, dx = 7 cmos integrated random phase jitter 19.44 mhz crystal used, 50 load rms jitter (155.52 mhz output) 470 700 fs rms 12 khz to 20 mhz, na = 112, vx = 2, dx = 7 rms jitter (38.88 mhz output) 440 650 fs rms 12 khz to 5 mhz, na = 112, vx = 2, dx = 28 lvpecl period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, na = 96, vx = 4, dx = 6 output peak-to-peak period jitter 13 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 2 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 19 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 3 ps rms 1,000 cycles, average of 25 measurements lvds period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, na = 96, vx = 4, dx = 6 output peak-to-peak period jitter 17 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 2 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 25 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 4 ps rms 1,000 cycles, average of 25 measurements cmos period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, 50 load, na = 96, vx = 4, dx = 6 output peak-to-peak period jitter 25 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 3 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak cycle-to-cycle jitter 36 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 6 ps rms 1,000 cycles, average of 25 measurements 1 all period and cycle-to-cycle jitter measurements are made wi th a tektronix dp o70604 oscilloscope. 2 x indicates either 0 or 1 for any given test condition.
ad9577 data sheet rev. 0 | page 6 of 44 pll2 fractional-n mode characteristics table 3. bleed = 1 parameter min typ max unit test conditions/comments 1 noise characteristics 25 mhz crystal used phase noise (155.52 mhz lvpecl output) nb = 87, frac = 57, mod = 625, vx = 2, dx = 7 @ 1 khz ?107 dbc/hz @ 10 khz ?115 dbc/hz @ 100 khz ?122 dbc/hz @ 1 mhz ?146 dbc/hz @ 10 mhz ?153 dbc/hz @ 30 mhz ?152 dbc/hz phase noise (622.08 mhz lvpecl output) nb = 99, frac = 333, mod = 625, vx = 2, dx = 2 @ 1 khz ?95 dbc/hz @ 10 khz ?103 dbc/hz @ 100 khz ?109 dbc/hz @ 1 mhz ?133 dbc/hz @ 10 mhz ?148 dbc/hz @ 30 mhz ?150 dbc/hz phase noise (155.52 mhz lvds output) nb = 87, frac = 57, mod = 625, vx = 2, dx = 7 @ 1 khz ?107 dbc/hz @ 10 khz ?114 dbc/hz @ 100 khz ?122 dbc/hz @ 1 mhz ?145 dbc/hz @ 10 mhz ?154 dbc/hz @ 30 mhz ?154 dbc/hz phase noise (622.08 mhz lvds output) nb = 99, frac = 333, mod = 625, vx = 2, dx = 2 @ 1 khz ?95 dbc/hz @ 10 khz ?103 dbc/hz @ 100 khz ?109 dbc/hz @ 1 mhz ?132 dbc/hz @ 10 mhz ?147 dbc/hz @ 30 mhz ?149 dbc/hz phase noise (155.52 mhz cmos output) nb = 87, frac = 57, mod = 625, vx = 2, dx = 7 @ 1 khz ?107 dbc/hz @ 10 khz ?114 dbc/hz @ 100 khz ?122 dbc/hz @ 1 mhz ?146 dbc/hz @ 10 mhz ?154 dbc/hz @ 30 mhz ?154 dbc/hz spread spectrum modulation range +0.1 ?0.5 % downspread, triangle modulation profile modulation frequency 31.25 khz programmable peak power reduction 10 db first harmonic of 100 mhz output, triangle modulation profile, spectrum analyzer resolution bandwidth = 20 khz 1 x indicates either 2 or 3 for any given test condition.
data sheet ad9577 rev. 0 | page 7 of 44 pll2 integer-n mode characteristics table 4. bleed = 0 parameter min typ max unit test conditions/comments 1 noise characteristics phase noise (106.25 mhz lvpecl output) nb = 102, vx = 4, dx = 6, f pfd = 25 mhz @ 1 khz ?116 dbc/hz @ 10 khz ?123 dbc/hz @ 100 khz ?127 dbc/hz @ 1 mhz ?148 dbc/hz @ 10 mhz ?156 dbc/hz @ 30 mhz ?158 dbc/hz phase noise (156.25 mhz lvpecl output) nb = 100, vx = 4, dx = 4, f pfd = 25 mhz @ 1 khz ?113 dbc/hz @ 10 khz ?120 dbc/hz @ 100 khz ?124 dbc/hz @ 1 mhz ?146 dbc/hz @ 10 mhz ?156 dbc/hz @ 30 mhz ?156 dbc/hz phase noise (625 mhz lvpecl output) nb = 100, vx = 2, dx = 2, f pfd = 25 mhz @ 1 khz ?101 dbc/hz @ 10 khz ?108 dbc/hz @ 100 khz ?112 dbc/hz @ 1 mhz ?134 dbc/hz @ 10 mhz ?149 dbc/hz @ 30 mhz ?150 dbc/hz phase noise (106.25 mhz lvds output) nb = 102, vx = 4, dx = 6, f pfd = 25 mhz @ 1 khz ?117 dbc/hz @ 10 khz ?123 dbc/hz @ 100 khz ?127 dbc/hz @ 1 mhz ?147 dbc/hz @ 10 mhz ?156 dbc/hz @ 30 mhz ?156 dbc/hz phase noise (156.25 mhz lvds output) nb = 100, vx = 4, dx = 4, f pfd = 25 mhz @ 1 khz ?113 dbc/hz @ 10 khz ?120 dbc/hz @ 100 khz ?124 dbc/hz @ 1 mhz ?145 dbc/hz @ 10 mhz ?155 dbc/hz @ 30 mhz ?155 dbc/hz phase noise (625 mhz lvds output) nb = 100, vx = 2, dx = 2, f pfd = 25 mhz @ 1 khz ?101 dbc/hz @ 10 khz ?108 dbc/hz @ 100 khz ?112 dbc/hz @ 1 mhz ?133 dbc/hz @ 10 mhz ?148 dbc/hz @ 30 mhz ?149 dbc/hz phase noise (106.25 mhz cmos output) nb = 102, vx = 4, dx = 6, f pfd = 25 mhz @ 1 khz ?117 dbc/hz @ 10 khz ?123 dbc/hz @ 100 khz ?127 dbc/hz @ 1 mhz ?147 dbc/hz @ 10 mhz ?156 dbc/hz @ 30 mhz ?157 dbc/hz
ad9577 data sheet rev. 0 | page 8 of 44 parameter min typ max unit test conditions/comments 1 phase noise (156.25 mhz cmos output) nb = 100, vx = 4, dx = 4, f pfd = 25 mhz @ 1 khz ?113 dbc/hz @ 10 khz ?119 dbc/hz @ 100 khz ?123 dbc/hz @ 1 mhz ?145 dbc/hz @ 10 mhz ?154 dbc/hz @ 30 mhz ?155 dbc/hz phase noise (155.52 mhz lvpecl output) nb = 112, vx = 2, dx = 7, f pfd = 19.44 mhz @ 1 khz ?112 dbc/hz @ 10 khz ?118 dbc/hz @ 100 khz ?126 dbc/hz @ 1 mhz ?147 dbc/hz @ 10 mhz ?155 dbc/hz @ 30 mhz ?156 dbc/hz phase noise (622.08 mhz lvpecl output) nb = 128, vx = 2, dx = 2, f pfd = 19.44 mhz @ 1 khz ?100 dbc/hz @ 10 khz ?106 dbc/hz @ 100 khz ?112 dbc/hz @ 1 mhz ?134 dbc/hz @ 10 mhz ?149 dbc/hz @ 30 mhz ?150 dbc/hz phase noise (155.52 mhz lvds output) nb = 112, vx = 2, dx = 7, f pfd = 19.44 mhz @ 1 khz ?113 dbc/hz @ 10 khz ?118 dbc/hz @ 100 khz ?126 dbc/hz @ 1 mhz ?145 dbc/hz @ 10 mhz ?154 dbc/hz @ 30 mhz ?155 dbc/hz phase noise (622.08 mhz lvds output) nb = 128, vx = 2, dx = 2, f pfd = 19.44 mhz @ 1 khz ?101 dbc/hz @ 10 khz ?106 dbc/hz @ 100 khz ?112 dbc/hz @ 1 mhz ?133 dbc/hz @ 10 mhz ?148 dbc/hz @ 30 mhz ?150 dbc/hz phase noise (155.52 mhz cmos output) nb = 112, vx = 2, dx = 7, f pfd = 19.44 mhz @ 1 khz ?113 dbc/hz @ 10 khz ?118 dbc/hz @ 100 khz ?126 dbc/hz @ 1 mhz ?146 dbc/hz @ 10 mhz ?155 dbc/hz @ 30 mhz ?155 dbc/hz 1 x indicates either 2 or 3 for any given test condition.
data sheet ad9577 rev. 0 | page 9 of 44 pll2 clock output jitter table 5. bleed = 0 for integer-n mode, bleed = 1 for fractional-n mode parameter 1 min typ max unit test conditions/comments 2 lvpecl integrated random phase jitter 25 mhz crystal used rms jitter (622.08 mhz output) 660 1200 fs rms 12 khz to 20 mhz, fractional-n operation, nb = 99, frac = 333, mod = 625, vx = 2, dx = 2 500 900 fs rms 50 khz to 80 mhz, fractional-n operation, nb = 99, frac = 333, mod = 625, vx = 2, dx = 2 rms jitter (625 mhz output) 470 800 fs rms 12 khz to 20 mhz, integer-n operation, nb = 100, vx = 2, dx = 2 380 650 fs rms 50 khz to 80 mhz, integer-n operation, nb = 100, vx = 2, dx = 2 rms jitter (155.52 mhz output) 630 1100 fs rms 12 khz to 20 mhz, fractional-n operation, nb = 87, frac = 57, mod = 625, vx = 2, dx = 7 rms jitter (156.25 mhz output) 470 800 fs rms 12 khz to 20 mhz, integer-n operation, nb = 100, vx = 4, dx = 4 lvds integrated random phase jitter 25 mhz crystal used rms jitter (622.08 mhz output) 660 1200 fs rms 12khz to 20 mhz, fractional-n operation, nb = 99, frac = 333, mod = 625, vx = 2, dx = 2 510 900 fs rms 50 khz to 80 mhz, fractional-n operation, nb = 99, frac = 333, mod = 625, vx = 2, dx = 2 rms jitter (625 mhz output) 470 820 fs rms 12 khz to 20 mhz, integer-n operation, nb = 100, vx = 2, dx = 2 380 650 fs rms 50 khz to 80 mhz, integer-n operation, nb = 100, vx = 2, dx = 2 rms jitter (155.52 mhz output) 620 1100 fs rms 12 khz to 20 mhz, fractional-n operation, nb = 87, frac = 57, mod = 625, vx = 2, dx = 7 rms jitter (156.25 mhz output) 480 800 fs rms 12 khz to 20 mhz, integer-n operation, nb = 100, vx = 4, dx = 4 cmos integrated random phase jitter 25 mhz crystal used, 50 load rms jitter (155.52 mhz output) 630 1100 fs rms 12 khz to 20 mhz, fractional-n operation, nb = 87, frac = 57, mod = 625, vx = 2, dx = 7 rms jitter (100 mhz output) 490 800 fs rms 12 khz to 20 mhz, integer-n operation, nb = 96, vx = 4, dx = 6 rms jitter (33.33 mhz output) 450 700 fs rms 12 khz to 5 mhz, integer-n operation, nb = 88, vx = 6, dx = 11 lvpecl integrated random phase jitter 19.44 mhz crystal used rms jitter (622.08 mhz output) 510 800 fs rms 12 khz to 20 mhz, integer-n operation, nb = 128, vx = 2, dx = 2 380 650 fs rms 50 khz to 80 mhz, integer-n operation, nb = 128, vx = 2, dx = 2 rms jitter (155.52 mhz output) 470 800 fs rms 12 khz to 20 mhz, integer-n operation, nb = 112, vx = 2, dx = 7 lvds integrated random phase jitter 19.44 mhz crystal used rms jitter (622.08 mhz output) 530 900 fs rms 12 khz to 20 mhz, integer-n operation, nb = 128, vx = 2, dx = 2 390 700 fs rms 50 khz to 80 mhz, integer-n operation, nb = 128, vx = 2, dx = 2 rms jitter (155.52 mhz output) 480 750 fs rms 12 khz to 20 mhz, integer-n operation, nb = 112, vx = 2, dx = 7
ad9577 data sheet rev. 0 | page 10 of 44 parameter 1 min typ max unit test conditions/comments 2 cmos integrated random phase jitter 19.44 mhz crystal used, 50 load rms jitter (155.52 mhz output) 470 700 fs rms 12 khz to 20 mhz, integer-n operation, nb = 112, vx = 2, dx = 7 rms jitter (38.88 mhz output) 430 650 fs rms 12 khz to 5 mhz, integer-n operation, nb = 112, vx = 2, dx = 28 lvpecl period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, integer-n operation, nb = 96, vx = 4, dx = 6 output peak-to-peak period jitter 13 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 2 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 19 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 3 ps rms 1,000 cycles, average of 25 measurements lvds period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, integer-n operation, nb = 96, vx = 4, dx = 6 output peak-to-peak period jitter 17 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 2 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 26 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 4 ps rms 1,000 cycles, average of 25 measurements cmos period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, 50 load, integer-n operation, nb = 96, vx = 4, dx = 6 output peak-to-peak period jitter 25 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 3 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle 36 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 6 ps rms 1,000 cycles, average of 25 measurements lvpecl period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, sscg on, nb = 100, frac = 0, mod = 1000, vx = 5, dx = 5, ckdiv = 7, numsteps = 59, fracstep = ?8, f out = 100 mhz with ?0.5% downspread at 30.2 khz output peak-to-peak period jitter 60 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 15 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 20 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 3 ps rms 1,000 cycles, average of 25 measurements lvds period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, sscg on, nb = 100, frac = 0, mod = 1000, vx = 5, dx = 5, ckdiv = 7, numsteps = 59, fracstep = ?8, f out = 100 mhz with ?0.5% downspread at 30.2 khz output peak-to-peak period jitter 63 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 15 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 25 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 4 ps rms 1,000 cycles, average of 25 measurements cmos period and cycle-to-cycle jitter (100 mhz output) 25 mhz crystal used, sscg on, 50 load, nb = 100, frac = 0, mod = 1000, vx = 5, dx = 5, ckdiv = 7, numsteps = 59, fracstep = ?8, f out = 100 mhz with ?0.5% downspread at 30.2 khz output peak-to-peak period jitter 70 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 15 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 36 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-cycle jitter 6 ps rms 1,000 cycles, average of 25 measurements
data sheet ad9577 rev. 0 | page 11 of 44 parameter 1 min typ max unit test conditions/comments 2 lvpecl period and cycle-to-cycle jitter (100.12 mhz output) 25 mhz crystal used, fractional-n operation, nb = 100, frac = 15, mod = 125, vx = 5, dx = 5 output peak-to-peak period jitter 13 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 2 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 20 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 3 ps rms 1,000 cycles, average of 25 measurements lvds period and cycle-to-cycle jitter (100.12 mhz output) 25 mhz crystal used, fractional-n operation, nb = 100, frac = 15, mod = 125, vx = 5, dx = 5 output peak-to-peak period jitter 17 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 2 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 26 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 4 ps rms 1,000 cycles, average of 25 measurements cmos period and cycle-to-cycle jitter (100.12 mhz output) 25 mhz crystal used, 50 load, fractional-n operation, nb = 100, frac = 15, mod = 125, vx = 5, dx = 5 output peak-to-peak period jitter 25 ps p-p 10,000 cycles, average of 25 measurements output rms period jitter 3 ps rms 10,000 cycles, average of 25 measurements output peak-to-peak, cycle-to-cycle jitter 36 ps p-p 1,000 cycles, average of 25 measurements output rms cycle-to-cycle jitter 6 ps rms 1,000 cycles, average of 25 measurements 1 all period and cycle-to-cycle jitter measurements are made wi th a tektronix dp o70604 oscilloscope. 2 x indicates either 2 or 3 for any given test condition. cmos reference clock output jitter table 6. parameter min typ max unit test conditions/comments jitter integration bandwidth jitter measurement at 25 mhz is equipment limited 12 khz to 5 mhz 680 1000 fs rms 25 mhz 200 khz to 5 mhz 670 950 fs rms
ad9577 data sheet rev. 0 | page 12 of 44 timing characteristics table 7. parameter min typ max unit test conditions/comments lvpecl (see figure 2 ) termination = 200 to 0 v, ac-coupled to 50 oscilloscope; c load = 5 pf output rise time, t rp 170 225 300 ps 20% to 80%, measured differentially output fall time, t fp 170 230 310 ps 80% to 20%, measured differentially skew 20 ps between the outputs of the same pll at the same frequency. syncch01/syncch23 set to 1 lvds (see figure 3 ) termination = 100 differential; c load = 5 pf output rise time, t rl 180 250 340 ps 20% to 80%, measured differentially output fall time, t fl 180 260 330 ps 80% to 20%, measured differentially skew 20 ps between the outputs of the same pll at the same frequency; syncch01/syncch23 set to 1 cmos (see figure 4 ) output rise time, t rc 250 680 950 ps termination is high impedance active probe, total c load = 5 pf, r load = 20 k, 20% to 80% output fall time, t fc 350 700 1000 ps termination is high impedance active probe, total c load = 5 pf, r load = 20 k, 80% to 20% skew 20 ps between the outputs of the same pll at the same frequency; syncch01/syncch23 set to 1 timing diagrams differential lvpecl 80% 50% 20% t rp v od t fp 09284-002 figure 2. lvpecl timing, differential differential lvds 80% 50% 20% t rl v od t fl 09284-003 figure 3. lvds timing, differential single-ended cmos 80% 20% t rc t fc 09284-004 figure 4. cmos timing, single-ended, 5 pf load
data sheet ad9577 rev. 0 | page 13 of 44 clock outputs ac coupling capacitors of 0.1 f used where appropriate. table 8. parameter min typ max unit test conditions/comments lvpecl clock outputs output frequency 637.5 mhz load is 200 to gnd at output pins, then ac-coupled to 50 terminated measurement equipment. output voltage swing, v od 610 740 950 mv load is 200 to gnd at output pins, then ac-coupled to 50 terminated measurement equipment. for differential amplitude, see figure 2 . duty cycle 45 55 % load is 200 to gnd at output pins, then ac-coupled to 50 terminated measurement equipment. output high voltage, v oh v s ? 1.24 v s ? 0.94 v s ? 0.83 v load is 127 /83 potential divider across supply dc-coupled into 1 m terminated measurement equipment, outputs static. output low voltage, v ol v s ? 2.07 v s ? 1.75 v s ? 1.62 v load is 127 /83 potential divider across supply dc-coupled into 1 m terminated measurement equipment, outputs static. lvds clock outputs output frequency 637.5 mhz load is ac-coupled to measurement equipment that provides 100 differential input termination. differential output voltage, v od 250 350 475 mv load is ac-coupled to measurement equipment that provides 100 differential input termination. for differential amplitude, see figure 3 . delta v od 25 mv load is ac-coupled to measurement equipment that provides 100 differential input termination. duty cycle 45 55 % load is ac-coupled to measurement equipment that provides 100 differential input termination. output offset voltage, v os 1.125 1.25 1.375 v load is dc-coupled to a 100 differential resistor into 1 m terminated measurement equipment, outputs static. delta v os 25 mv load is dc-coupled to a 100 differential resistor into 1 m terminated measurement equipment, outputs static. short-circuit current, i sa , i sb 13 24 ma load is dc-coupled to a 100 differential resistor into 1 m terminated measurement equipment, output shorted to gnd. cmos clock outputs output frequency 200 mhz output high voltage, v oh v s ? 0.15 v sourcing 1.0 ma current, outputs static. output low voltage, v ol 0.1 v sinking 1.0 ma current, outputs static. duty cycle 45 55 % termination is high impedance active probe; total c load = 5 pf, r load = 20 k.
ad9577 data sheet rev. 0 | page 14 of 44 power table 9. parameter min typ max unit test conditions/comments power supply 3.0 3.3 3.6 v lvpecl power dissipation 1235 1490 mw typical part configuration, both plls enabled for integer-n operation, f out0 = 156.25 mhz, f out1 = 125 mhz, f out2 = 100 mhz, f out3 = 33.33 mhz, na = 100, v0 = 4, d0 = 4, v1 = 4, d1 = 5, nb = 96, v2 = 4, d2 = 6, v3 = 4, d3 = 18, 25 mhz crystal used, load is 200 to gnd at output pins, then ac-coupled to 50 terminated measurement equipment 1270 1530 mw worst-case part configuration, pll2 in fractional-n mode, with sscg enabled, f out0 = 379.16 mhz, f out1 = 379.16 mhz, f out2 = 359.33 mhz, f out3 = 359.33 mhz, na = 91, v0 = 3, d0 = 2, v1 = 3, d1 = 2, nb = 86, v2 = 3, d2 = 2, v3 = 3, d3 = 2, frac = 300, mod = 1250, ckdiv = 5, numsteps = 77, fracstep = ?7, ?0.5% downspread at 32 khz, 25 mhz crystal used, load is 200 to gnd at output pins, then ac-coupled to 50 terminated measurement equipment lvds power dissipation 1020 1200 mw typical part configuration, both plls enabled for integer-n operation, f out0 = 156.25 mhz, f out1 = 125 mhz, f out2 = 100 mhz, f out3 = 33.33 mhz, na = 100, v0 = 4, d0 = 4, v1 = 4, d1 = 5, nb = 96, v2 = 4, d2 = 6, v3 = 4, d3 = 18, 25 mhz crystal used, load ac-coupled to measurement equipment that provides 100 differential input termination 1085 1290 mw worst-case part configuration, pll2 in fractional-n mode, with sscg enabled, f out0 = 379.16 mhz, f out1 = 379.16 mhz, f out2 = 359.33 mhz, f out3 = 359.33 mhz, na = 91, v0 = 3, d0 = 2, v1 = 3, d1 = 2, nb = 86, v2 = 3, d2 = 2, v3 = 3, d3 = 2, frac = 300, mod = 1250, ckdiv = 5, numsteps = 77, fracstep = ?7, ?0.5% downspread at 32 khz, 25 mhz crystal used, load ac-coupled to measurement equipment that provides 100 differential input termination cmos power dissipation 1065 1380 mw typical part configuration, both plls enabled for integer-n operation, f out0 = 156.25 mhz, f out1 = 125 mhz, f out2 = 100 mhz, f out3 = 33.33 mhz, na = 100, v0 = 4, d0 = 4, v1 = 4, d1 = 5, nb = 96, v2 = 4, d2 = 6, v3 = 4, d3 = 18, 25 mhz crystal used, eight single-ended outputs active, c load = 5 pf 1190 1510 mw worst-case part configuration, pll2 in fractional-n mode, with sscg enabled, f out0 = 189.58 mhz, f out1 = 189.58 mhz, f out2 = 179.66 mhz, f out3 = 179.66 mhz, na = 91, v0 = 3, d0 = 4, v1 = 3, d1 = 4, nb = 86, v2 = 3, d2 = 4, v3 = 3, d3 = 4, frac = 300, mod = 1250, ckdiv = 5, numsteps = 77, fracstep = ?7, ?0.5% downspread at 32 khz, 25 mhz crystal used, eight single-ended outputs active, c load = 5 pf power changes reduction in power due to turning off a channel of one vco divider, one output divider, and one output buffer; data for channel 1, with typical part configuration, both plls enabled for integer-n operation, f out0 = 156.25 mhz, f out1 = 125 mhz, f out2 = 100 mhz, f out3 = 33.33 mhz, na = 100, v0 = 4, d0 = 4, v1 = 4, d1 = 5, nb = 96, v2 = 4, d2 = 6, v3 = 4, d3 = 18, 25 mhz crystal used power-down 1 lvpecl channel 160 205 mw load 200 to gnd at output pins, and ac-coupled to 50 terminated measurement equipment power-down 1 lvds channel 105 155 mw load ac-coupled to measurement equipment that provides 100 differential input termination power-down 1 cmos channel 130 170 mw eight single-ended outputs active, c load = 5 pf
data sheet ad9577 rev. 0 | page 15 of 44 crystal oscillator table 10. parameter min typ max unit test conditions/comments crystal specification fundamental mode frequency 19.44 25 27 mhz reference divider, r = 1, only esr 50 load capacitance 14 pf phase noise ?135 dbc/hz 1 khz offset stability ?50 +50 ppm reference input table 11. parameter min typ max unit test conditions/comments clock input (refclk) input frequency 19.44 25 27 mhz reference divider, r = 1 38.88 50 54 mhz reference divider, r = 2 input high voltage 2.0 v input low voltage 0.8 v input current ?1.0 +1.0 a input capacitance 2 pf control pins table 12. parameter min typ max unit test conditions/comments input characteristics sscg, max_bw, and margin sscg, max_bw, and margin have a 30 k internal pull-down resistor logic 1 voltage 2.0 v logic 0 voltage 0.8 v logic 1 current 240 a logic 0 current 40 a refsel refsel has a 30 k internal pull-up resistor logic 1 voltage 2.0 v logic 0 voltage 0.8 v logic 1 current 70 a logic 0 current 240 a i 2 c dc characteristics lvcmos; the scl and sda pins only, see figure 48 input voltage high 0.7 vcc v input voltage low 0.3 vcc v input current ?10 +10 a v in = 0.1 v cc or v in = 0.9 v cc output low voltage 0.4 v v ol with a load current of i ol = 3.0 ma i 2 c timing characteristics lvcmos; the scl and sda pins only, see figure 48 scl clock frequency 400 khz scl pulse width high high, t high 600 ns low, t low 1300 ns start condition hold time, t hd; sta 600 ns setup time, t su; sta 600 ns data setup time, t su; dat 100 ns hold time, t hd; dat 300 ns stop condition setup time, t su; sto 600 ns bus free time between a stop and a start, t buf 1300 ns
ad9577 data sheet rev. 0 | page 16 of 44 absolute maximum ratings thermal characteristics table 13. parameter thermal impedance measurements were taken on a 4-layer board in still air in accordance with eia/jesd51-7. rating v s to gnd ?0.3 v to +3.6 v refclk to gnd ?0.3 v to v s + 0.3 v table 14. thermal resistance package type ja ldo to gnd ?0.3v to v s + 0.3 v unit xt1, xt2 to gnd ?0.3 v to v s + 0.3 v 40-lead lfcsp 27.5 c/w ?0.3 v to v s + 0.3 v sscg, max_bw, margin, scl, sda, refsel to gnd refout, outxp, outxn to gnd ?0.3 v to v s + 0.3 v esd caution junction temperature 1 150c storage temperature ?65c to+150c lead temperature (10 sec) 300c 1 see the thermal characteristics section for ja . stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability.
data sheet ad9577 rev. 0 | page 17 of 44 pin configuration and fu nction descriptions notes 1. the exposed paddle on this pa ckage is an electrical connection as well as a thermal enhancement. for the device to function properly, the paddle must be attached to ground (gnd). it is recommended that a minimum of nine vias be used to connect the paddle to the printed circuit board (pcb) ground plane. pin 1 indicator 1 vsca 2 vsi2c 3 refout 4 vsrefout 5 vsx 6 refclk 7 xt2 8 xt1 9 refsel 10 vscb 23 out3p 24 vsfb 25 vsm 26 sscg 27 vsfa 28 out1n 29 out1p 30 vsob1a 22 out3n 21 vsob3b 11 tst1b 12 tst2b 13 ldo 15 gnd 17 out2n 16 gnd 18 out2p 19 vsob2b 20 margin 14 vsvb 33 out0n 34 out0p 35 gnd 36 gnd 37 scl 38 vsva 39 tst2a 40 max_bw 32 vsob0a 31 sda top view (not to scale) ad9577 09284-005 figure 5. pin configuration table 15. pin function descriptions pin no. mnemonic description 1 vsca pll1 power supply. 2 vsi2c i 2 c digital power supply. 3 refout cmos reference output. 4 vsrefout reference output buffer power supply. 5 vsx crystal oscillator and input reference power supply. 6 refclk reference clock input. tie low when not in use. 7, 8 xt2, xt1 external 19.44 mhz to 27 mhz crystal. leave unconnected when not in use. 9 refsel logic input. use this pin to select the re ference source. internal 30 k pull-up resistor. 10 vscb pll2 analog power supply. 11 tst1b test pin. connect this pin to pin 13 (ldo). 12 tst2b test pin. connect this pin to pin 13 (ldo). 13 ldo this pin is for bypassing the pll2 ldo to ground with a 220 nf capacitor. 14 vsvb pll2 vco power supply. 15, 16, 35, 36 gnd ground. 17 out2n lvpecl/lvds/cmos clock output. 18 out2p lvpecl/lvds/cmos clock output. 19 vsob2b output port out2 power supply. 20 margin logic 1 sets the margining frequency on the clock output pins. internal 30 k pull-down resistor. 21 vsob3b output port out3 power supply. 22 out3n lvpecl/lvds/cmos clock output. 23 out3p lvpecl/lvds/cmos clock output. 24 vsfb pll2 analog power supply. 25 vsm pll2 digital power supply. 26 sscg logic 1 enables spread spectrum operation of pll2. internal 30 k pull-down resistor. 27 vsfa pll1 analog power supply. 28 out1n lvpecl/lvds/cmos clock output. 29 out1p lvpecl/lvds/cmos clock output.
ad9577 data sheet rev. 0 | page 18 of 44 pin no. mnemonic description 30 vsob1a output port out1 power supply. 31 sda serial data line for i 2 c. 32 vsob0a output port out0 power supply. 33 out0n lvpecl/lvds/cmos clock output. 34 out0p lvpecl/lvds/cmos clock output. 37 scl serial clock for i 2 c. 38 vsva pll1 vco power supply. 39 tst2a test pin. connect this pin to the printed circuit board (pcb) ground plane. 40 max_bw logic 1 widens the loop bandwidth of the fractional -n pll during spread spectrum. internal 30 k pull- down resistor. epad the exposed paddle on this package is an electrical connection as well as a thermal enhancement. for the device to function properly, the paddle must be attached to ground (gnd). it is recommended that a minimum of nine vias be used to connect the paddl e to the printed circuit board (pcb) ground plane.
data sheet ad9577 rev. 0 | page 19 of 44 typical performance characteristics refout and pll1 phase noise performance ? 100 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-006 figure 6. phase noise, refout output, 25 mhz (f xtal = 25 mhz) ? 100 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-007 figure 7. phase noise, pll1, out0 lvpecl, 106.25 mhz, integer-n mode (f xtal = 25 mhz, na = 102, v0 = 4, d0 = 6) ? 80 ?90 ?100 ?170 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-008 figure 8. phase noise, pll1, out0 lvpecl, 156.25 mhz integer-n mode (f xtal = 25 mhz, na = 100, v0 = 4, d0 = 4) ? 100 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-009 figure 9. phase noise, pll1, out0 lvpecl, 100 mhz, integer-n mode (f xtal = 25 mhz, na = 100, v0 = 5, d0 = 5) ? 100 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-010 figure 10. phase noise, pll1, out0 lvpecl, 125 mhz, integer-n mode (f xtal = 25 mhz, na = 100, v0 = 4, d0 = 5) ? 80 ?90 ?100 ?170 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-011 figure 11. phase noise, pll1, out0 lvpecl, 625 mhz, integer-n mode (f xtal = 25 mhz, na = 100, v0 = 2, d0 = 2)
ad9577 data sheet rev. 0 | page 20 of 44 pll2 phase noise performance ? 110 ?160 ?150 ?140 ?130 ?120 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-012 figure 12. phase noise, pll2, out2 lvpecl, 100 mhz, integer-n mode (f xtal = 25 mhz, nb = 100, v2 = 5, d2 = 5) ? 100 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-013 figure 13. phase noise, pll2, out2 lvpecl, 156.25 mhz, integer-n mode (f xtal = 25 mhz, nb = 100, v2 = 4, d2 = 4) ? 100 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-014 figure 14. phase noise, pll2, out2 lvpecl, 155.52 mhz, fractional-n mode (f xtal = 25 mhz, nb = 99, frac = 333, mod = 625, v2 = 2, d2 = 8), spurs disabled ? 110 ?160 ?150 ?140 ?130 ?120 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-015 figure 15. phase noise, pll2, out2 lvpecl, 106.25 mhz, integer-n mode (f xtal = 25 mhz, nb = 102, v2 = 4, d2 = 6) ? 90 ?100 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-016 figure 16. phase noise, pll2, out2 lvpecl, 625 mhz, integer-n mode (f xtal = 25 mhz, nb = 100, v2 = 2, d2 = 2) ? 90 ?100 ?160 ?150 ?140 ?130 ?120 ?110 1k 10k 100k 1m 100m 10m phase noise (dbc/hz) frequency (hz) 09284-017 figure 17. phase noise, pll2, out2 lvpecl, 622.08 mhz, fractional-n mode (f xtal = 25 mhz, nb = 99, frac = 333, mod = 625, v2 = 2, d2 = 2), spurs disabled
data sheet ad9577 rev. 0 | page 21 of 44 output jitter 480 475 470 465 460 455 450 445 440 435 430 86 87 88 89 90 91 92 93 94 95 96 97 98 99 101100 102 na 09284-018 integr a ted rms phase jitter (fs) figure 18. typical integrated random phase jitter in fs rms for pll1 and out0p lvpecl as feedback divider value na swept (f xtal = 25 mhz, v0 = 5, d0 = 5) 500 440 490 480 470 460 450 nb 09284-021 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 integr a ted rms phase jitter (fs) figure 19. typical integrated random phase jitter in fs rms for pll2 and out2p lvpecl as feedback divider value nb swept (f xtal = 25 mhz, v2 = 5, d2 = 5, integer-n mode)
ad9577 data sheet rev. 0 | page 22 of 44 typical output signal 200mv/di v 5ns/div 09284-024 figure 20 typical lvpecl differential output trace, 156.25 mhz 100mv/di v 5ns/div 09284-025 figure 21. typical lvds differential output trace, 156.25 mhz 500mv/div 1ns/div 09284-026 figure 22. typical cmos output trace, 200mhz 200mv/di v 1ns/div 09284-027 figure 23. typical lvpecl differential output trace, 625 mhz 100mv/di v 1ns/div 09284-028 figure 24. typical lvds differential output trace, 625 mhz 500mv/di v 10ns/div 09284-029 figure 25. typical refout output trace, 25 mhz
data sheet ad9577 rev. 0 | page 23 of 44 2.5 3.5 3.4 3.3 3.2 3.1 3.0 2.9 2.8 2.7 2.6 02 180 160 140 120100 80 60 40 20 single-ended output swing (v) frequency (mhz) 09284-030 0 0 0.5pf load 5.2pf load 10.5pf load figure 26. cmos single-ended, peak-t o-peak output swing vs. frequency, for loads of 0.5 pf, 5.2 pf, and 10.5 pf, measured with a tektronix p7313 active probe 1.8 1.2 1.3 1.4 1.5 1.6 1.7 0 100 200 300 400 500 600 differential peak-to-peak output swing (v) frequency (mhz) 09284-031 figure 27. lvpecl differential, peak-to-peak output swing vs. frequency 900 400 500 600 700 800 0 100 200 300 400 500 600 frequency (mhz) 09284-032 differential peak-to-peak output swing (v) figure 28. lvds differential, peak-to-peak output swing vs. frequency
ad9577 data sheet rev. 0 | page 24 of 44 typical spread spectrum performance characteristics 100.1 100.0 99.4 99.5 99.6 99.7 99.8 99.9 frequency (mhz) time (10s/div) 09284-033 figure 29. typical spread spectrum frequency modulation profile out2, nb = 96, frac = 0, mod = 1000, ckdiv = 7, numsteps = 59, fracstep = ?8, f out = 100 mhz with ?0.5% downspread at 30.2 khz, max_bw set to 0 10 0 ?10 ?20 ?80 ?70 ?60 ?50 ?40 ?30 99.00 100.50 100.25 100.00 99.75 99.50 99.25 power (dbm) frequency (mhz) unmodulated clock spectrum modulated clock 09284-034 figure 30. typical nonspread and sp read spectrum power spectra, out2, nb = 96, frac = 0, mod = 1000, ckdiv = 7, numsteps = 59, fracstep = ?8, f out = 100 mhz with ?0.5% downspread at 30.2 khz, max_bw set to 0, first harmonic shown, spectrum anal yzer resolution bandwidth =10 khz, maximum hold on 0 ?10 ?20 ?90 ?80 ?70 ?60 ?50 ?40 ?30 695 701 699 697 power (dbm) frequency (mhz) 09284-035 figure 31. typical nonspread and sp read spectrum power spectra, out2, nb = 96, frac = 0, mod = 1000, ckdiv = 7, numsteps = 59, fracstep = ?8, f out = 100 mhz with ?0.5% downspread at 30.2 khz, max_bw set to 0, seventh harmonic shown, spectrum analyzer resolution bandwidth = 120 khz, maximum hold on
data sheet ad9577 rev. 0 | page 25 of 44 terminology phase jitter and phase noise an ideal sine wave can be thought of as having a continuous and even progression of phase with time from 0 to 360 for each cycle. actual signals, however, display a certain amount of variation from ideal phase progression over time, which is called phase jitter. although many causes can contribute to phase jitter, one major cause is random noise, which is characterized statistically as being gaussian (normal) in distribution. this phase jitter leads to a spreading out of the energy of the sine wave in the frequency domain, producing a continuous power spectrum. this power spectrum is usually reported as a series of values whose units are dbc/hz at a given offset in frequency from the sine wave (carrier). the value is a ratio (expressed in db) of the power contained within a 1 hz band- width with respect to the power at the carrier frequency. for each measurement, the offset from the carrier frequency is also given. it is meaningful to integrate the total power contained within some interval of offset frequencies (for example, 12 khz to 20 mhz). this is called the integrated phase noise over that frequency offset interval and can be readily related to the time jitter due to the phase noise within that offset frequency interval. phase noise has a detrimental effect on error rate performance by increasing eye closure at the transmitter output and reducing the jitter tolerance/sensitivity of the receiver. time jitter phase noise is a frequency domain phenomenon. in the time domain, the same effect is exhibited as time jitter. when observing a sine wave, the time of successive zero crossings vary. in a square wave, the time jitter is seen as a displacement of the edges from their ideal (regular) times of occurrence. in both cases, the variations in timing from the ideal are the time jitter. because these variations are random in nature, the time jitter is specified in units of seconds root mean square (rms) or 1 sigma of the gaussian distribution. additive phase noise it is the amount of phase noise that is attributable to the device or subsystem being measured. the phase noise of any external oscillators or clock sources has been subtracted. this makes it possible to predict the degree to which the device affects the total system phase noise when used in conjunction with the various oscillators and clock sources, each of which contributes its own phase noise to the total. in many cases, the phase noise of one element dominates the system phase noise. additive time jitter it is the amount of time jitter that is attributable to the device or subsystem being measured. the time jitter of any external oscillators or clock sources has been subtracted. this makes it possible to predict the degree to which the device will affect the total system time jitter when used in conjunction with the various oscillators and clock sources, each of which contributes its own time jitter to the total. in many cases, the time jitter of the external oscillators and clock sources dominates the system time jitter. random jitter measurement on the ad9577 , the rms jitter measurements are made by integrating the phase noise, with spurs disabled. there are two reasons for this. first, because the part is highly configurable, any measured spurs are a function of the current programmed state of the device. for example, there may be a small reference spur at the pfd frequency present on the output spectrum. if the pfd operates at 19.44 mhz (which is common for telecommunications applications), the resulting jitter falls within the normal 12 khz to 20 mhz integration bandwidth. when the pfd operates above 20 mhz, the deterministic jitter is not included in the measurement. as another example, for pll2, the value of the chosen frac and mod values affects the amplitude and location of a spur, and therefore, it is not possible to configure the pll to provide a general measurement that includes spurs. the second, and more significant reason, is due to the statistical nature of spurious components. the jitter performance information of the clock generator is required so that a jitter budget for the complete communications channel can be established. by knowing the jitter characteristics at the ultimate receiver, the data bit error rate (ber) can be estimated to ensure robust data transfer. the received jitter characteristic consists of random jitter (rj), due to random perturbations such as thermal noise, and deterministic jitter (dj), due to deterministic perturbations such as crosstalk spurs. to make an estimate of the ber, the total jitter peak-to-peak (tj p-p) value must be known. it is the total jitter value that determines the amount of eye closure at the receiver and, consequently, the bit error rate. the tj p-p value is specified for a given number of clock edges. for example, in networking applications, the tj is specified for 1 12 clock edges. the equation for the total jitter peak-to-peak is tj p-p = dj p-p + 2 q rj rms (1) where the q factor represents the ratio of the expected peak deviation to the standard deviation in a gaussian process for a given population (of edge crossings). for 1 12 clock edges, q is 7.03; therefore, for networking applications, the total jitter peak- to-peak is estimated by tj p-p = dj p-p + 14.06 rj rms (2)
ad9577 data sheet rev. 0 | page 26 of 44 therefore, to accurately estimate the tj p-p, separate measurements of the rms value of the random jitter (rj rms) and the peak-to-peak value of the deterministic jitter (dj p-p) must be taken. to measure the rj rms of the clock signal, integrate the clock phase noise over the desired bandwidth, with spurs disabled (that is, removed) from the measurement. if the dj spurs were included in the measurement, the dj contribution would also be mult iplied by 14.06 in equation 2, leading to a grossly pessimistic estimate of the total jitter. this is why it is important to measure the integrated jitter with spurs disabled. due to the 14.06 factor in equation 2, the spurious dj components on the clock output only have a small impact on the tj p-p measurement and, consequently, the system ber performance. therefore, it is clear that the dj component (that is, the spur) should not be added to the rms value of the random jitter directly. however, if the phase noise jitter measurement was preformed with spurs enabled, this is exactly what the measurement would be reporting. for more background information, see fibre channel, methodologies for jitter and signal quality specification-mjsq , rev. 14, june 9, 2004.
data sheet ad9577 rev. 0 | page 27 of 44 detailed block diagram xtal osc refclk xt1 xt2 margin sscg max_bw refsel cmos ad9577 divide 1 or 2 scl sda i 2 c control 22pf 22pf vco 2.15ghz to 2.55ghz pfd/cp third order lpf ldo1 divide by 80 to 131 feedback divider f pfd pll1 n a divide by 2to 6 divide by 1to 32 lvpecl/lvds refout or 2 cmos v0 d0 format1 divide by 2to 6 divide by 1to 32 lvpecl/lvds or 2 cmos v1 d1 vco dividers output dividers output buffers vco 2.15ghz to 2.55ghz pfd/cp third order lpf ldo2 divide by 80 to 131 feedback divider pll2 n b divide by 2to 6 divide by 1to 32 lvpecl/lvds or 2 cmos v2 d2 format2 divide by 2to 6 divide by 1to 32 lvpecl/lvds or 2 cmos v3 d3 sdm vco dividers output dividers output buffers 3-bit 0 1 frac frac_triwave sscg mod f pfd ckdiv frac fracstep numsteps sscg triwave generator frac_triwave 220nf ldo 4 gnd + paddle 14 vs 09284-036 figure 32. detailed block diagram
ad9577 data sheet rev. 0 | page 28 of 44 example application xtal osc refclk margin refsel cmos ad9577 divide 1 or 2 vco 2.15ghz to 2.55ghz pfd/cp third order lpf ldo feedback divider f pfd pll1 dividers 156.25mhz lvpecl dividers 125mhz lvpecl ldo vco 2.15ghz to 2.55ghz pfd/cp third order lpf pll2 dividers 100mhz lvds dividers 33.33mhz 2 cmos feedback divider scl sda i 2 c control sscg spread spectrum, sdm max_bw 2 5mhz xtal 25mhz cmos note that any frequencies may be programmed. 09284-037 figure 33. example application achievable application frequencies include (but are not limited to) those listed in table 16 . table 16. typical application frequencies applications frequency (mhz) ethernet 25, 62.5, 100, 125, 250 10g ethernet 155.52, 156.25, 187.5, 161.1328125, 312.5, 622.08, 625 fb-dimm 133.333, 166.666, 200 fibre channel 53.125, 106.25, 212.5, 318.75, 425 10g fibre channel 159.375 inifiniband 125 sas, sata 37.5, 75, 100, 120, 150; the ad9577 also meets the ?0.5% downspread requirement telecomm 19.44, 38.88, 77.76, 155.52, 311.04, 622.08, 627.32962 pci express 100, 125, 250; the ad9577 also meets the ?0.5% downspread requirement pci, pci-x 33.33, 66.66, 100, 133.33, 200 video 13.5, 14.318, 17.7, 18, 27, 72, 74.25, 74.25/1.001, 148.5, 148.5/1.001 wireless infrastructure 61.44, 122.88, 368.64
data sheet ad9577 rev. 0 | page 29 of 44 functional description on the ad9577 , parameters can be programmed over an i 2 c bus to provide custom output frequencies, output formats, and feature selections. however, this programming must be repeated after every power cycle of the part. the ad9577 contains two plls, pll1 and pll2, used for independent clock frequency generation, as shown in figure 32 . a shared crystal oscillator and reference clock input cell drive both plls. the reference clock of the plls can be selected as either the crystal oscillator output or the reference input clock. a reference divider precedes each pll. when the crystal oscillator input is selected, these dividers must be set to divide by 1. when the reference input is selected, these dividers can be set to divide by 1 or divide by 2, provided that the resulting input frequency to the plls is within the permitted 19.44 mhz to 27 mhz range. both reference dividers are set to divide by the same value. each pll drives two output channels, producing four output ports in total for the ic. each output channel consists of a vco divider block, followed by an output divider block. the output divider blocks each drive with an output buffer port. each output buffer port can be configured as a differential lvds output, a differential lvpecl output, or two lvcmos outputs. additionally, a cmos-buffered version reference clock frequency is available. the upper pll in figure 32 , pll1, is an integer-n pll. by setting the feedback divider value (na), the vco output frequency can tuned over the 2.15 ghz to 2.55 ghz range to integer multiples of the pfd input frequency. by setting each of the vco divider (v0 and v1) and output divider (d0 and d1) values, the vco frequency can be divided down to the required output frequency, independently, for each of the output ports, out0 and out1. the loop filter required for this pll is integrated on chip. the lower pll in figure 32 , pll2, is a fractional-n pll. this pll can optionally operate as an integer-n pll for optimum jitter performance. by setting the feedback divider value (nb) and the - modulator fractional (frac) and modulus (mod) values, the vco output frequency can tune over the 2.15 ghz to 2.55 ghz range. the vco frequency is a fractional multiple of the pfd input frequency. in this way, the vco frequency can tune to obtain frequencies that are not constrained to integer multiples of the pfd frequency. by setting each of the vco divider (v2 and v3) and output divider (d2 and d3) values, the vco frequency can be divided down to the required output frequency, independently, for each of the output ports, out2 and out3. the loop filters required for this pll are integrated on chip. the pll2 can operate to modulate the output frequency between its nominal value and a value that is up to ?0.5% lower. this provides spread spectrum modulation up to ?0.5% downspread. spread spectrum frequency modulation can reduce the peak power output of the clock source and any circuitry that it drives and lead to reduced emi emissions. in the ad9577 , the frequency modulation profile is triangular. the modulation frequency and modulation range parameters are all programmable. both plls can be programmed to generate a second independent frequency map under the control of the margin pin. this feature can be used to test the frequency robustness of a system. reference input and reference dividers the reference input section is shown in figure 34 . when the refsel pin is pulled high, the crystal oscillator circuit is enabled. the crystal oscillator circuit needs an external crystal cut to resonate in fundamental mode in the 19.44 mhz to 27 mhz range, with 25 mhz being used in most networking applications. the total load capacitance presented to the crystal should add up to 14 pf. in the example shown in figure 34 , parasitic trace capacitance of 1.5 pf and an ad9577 input pin capacitance of 1.5 pf are assumed, with the series combination of the two 22 pf capacitances providing an additional 11 pf. when the refsel pin is pulled low, the crystal oscillator powers down, and the refclk pin must provide a good quality reference clock instead. either a dc-coupled lvcmos level signal or an ac-coupled square wave can drive this single-ended input, provided that an external potential divider is used to bias the input at v s /2. the output of the crystal oscillator and reference input circuitry is routed to a reference divider circuit to further divide down the reference input frequency to the plls by 1 or 2. when the crystal oscillator circuit is used, the dividers must be set to divide by 1. the input frequency to the plls must be in the 19.44 mhz to 27 mhz range. the divide ratio is set to 1 by programming the value of r, register g0[1], to 0. the divide ratio is set to 2 by programming the value of r to 1. xtal osc divide 1 or 2 to plls refclk refsel 22pf 22pf 09284-038 figure 34. reference input section and reference dividers table 17. refsel (pin 9) definition refsel reference source 0 refclk input 1 crystal oscillator table 18. reference divider setting r, register g0[1] reference divide ratio 0 divide by 1 1 divide by 2
ad9577 data sheet rev. 0 | page 30 of 44 output channel dividers between each vco and its associated chip outputs, there are two divider stages: a vco divider that has a divide ratio between 2 and 6 and an output divider that can be set to divide between 1 and 32. this cascade of dividers allows a minimum output channel divide ratio of 2 and a maximum of 192. with vco frequencies ranging between 2.15 ghz and 2.55 ghz, the part can be programmed to spot frequencies over a continuous frequency range of from 11.2 mhz to 200 mhz, and it can be programmed to spot frequencies over a continuous frequency range of 200 mhz and 637.5 mhz, with only a few small gaps. table 19. divider ratio setting registers divider i 2 c registers parameter divide range channel 0 vco divider adv0[7:5] v0 2 to 6 channel 1 vco divider adv1[7:5] v1 2 to 6 channel 2 vco divider bdv0[7:5] v2 2 to 6 channel 3 vco divider bdv1[7:5] v3 2 to 6 channel 0 output divider adv0[4:0] d0 1 to 32 1 channel 1 output divider adv1[4:0] d1 1 to 32 1 channel 2 output divider bdv0[4:0] d2 1 to 32 1 channel 3 output divider bdv1[4:0] d3 1 to 32 1 1 set to 00000 for divide by 32. asserting the syncch01 or syncch23 bits (register adv2[0] or register bdv2[0]) allows each pll output channel to use a common vco divider. this feature allows the out0/out1 and out2/out3 output ports to have minimal skew when their relative output channel divide ratio is an integer multiple. duty-cycle correction circuitry ensures that the output duty cycle remains at 50%. v0[2:0] d0[4:0] out0 output divider vco divider v1[2:0] d1[4:0] out1 output divider vco divider v co v2[2:0] d2[4:0] out2 output divider vco divider v3[2:0] d3[4:0] out3 output divider vco divider vco 09284-039 figure 35. output channe l divider signal path outputs each output port can be individually configured as either differential lvpecl, differential lvds, or two single-ended lvcmos clock outputs. the simplified equivalent circuit of the lvds outputs is shown in figure 36 . 3.5ma 3.5ma outxp outxn 09284-040 figure 36. lvds outputs simp lified equivalent circuit the simplified equivalent circuit of the lvpecl outputs is shown in figure 37 . 3.3 v outxp outxn gnd 09284-041 figure 37. lvpecl outputs simplified equivalent circuit output channels (consisting of a vco divider, output divider, and an output buffer) can be individually powered down to save power. setting pdch0, pdch1, pdch2, and pdch3 (register bp0[1:0] and register dr1[7:6]) powers down the appropriate channel. output buffer combinations of lvds, lvpecl, and cmos can be selected by setting dr1[5:0] as is shown in table 20 and table 21 . table 20. pll1 output driver format control bits, register dr1[2:0] format1 (pll1) register dr1[2:0] out1p/out1n out0p/out0n 000 lvpecl lvpecl 001 lvds lvds 010 2 cmos lvpecl 011 2 cmos 2 cmos 100 2 cmos lvds 101 lvpecl lvds 110 lvpecl 2 cmos 111 1 2 cmos 2 cmos 1 this indicates that the cmos outputs are in phase; otherwise, they are in antiphase.
data sheet ad9577 rev. 0 | page 31 of 44 table 21.pll2 output driver format control bits, register dr1[5:3] format2 (pll2) register dr1[5:3] out3p/out3n out2p/out2n 000 lvpecl lvpecl 001 lvds lvds 010 2 cmos lvpecl 011 2 cmos 2 cmos 100 2 cmos lvds 101 lvpecl lvds 110 lvpecl 2 cmos 111 1 2 cmos 2 cmos 1 this indicates that the cmos outputs are in phase; otherwise, they are in antiphase. lvds uses a current mode output stage. the normal value (default) for this current is 3.5 ma, which yields a 350 mv output swing across a 100 resistor. the lvds outputs meet or exceed all ansi/tia/eia-644 specifications. the lvds output buffer should be terminated with a 100 differential resistor between the receiver input ports (see figure 38 ). a recommended termination circuit for the lvds outputs is shown in figure 38 . 50? 50? lvds 100? lvds 09284-042 figure 38. lvds output termination see the an-586 application note , lv d s o ut pu t s for hi g h s p e e d a/d converters , for more information about lvds. in a dc-coupled application, the lvpecl output buffer should be terminated via a pair of 50 resistors to a voltage of v cc ? 2 v. this can be implemented by using potential dividers of 127 and 83 between the supplies, as shown in figure 39 . 3.3v 50? 50? single-ended (not coupled) 3.3v 3.3 v lvpecl 127 ? 127 ? 83 ? 83 ? v t = v dd ? 2v lvpecl 09284-043 figure 39. lvpecl dc-coupled termination an alternative lvpecl termination scheme for dc-coupled applications is shown figure 40 . 50? 50? lvpecl 50 ? 50? 50 ? lvpecl 09284-044 figure 40. lvpecl dc-coupled y-termination in ac-coupled applications, the lvpecl output stage needs a pair of 200 pull-down resistors to gnd to provide a dc path for the output stage emitter followers (see figure 41 ). the receiver must provide an additional 50 single-ended input termination. 50? 50? lvpecl 50? 50? 200? 200 ? lvpecl v term 0.1f 0.1f 09284-045 figure 41. lvpecl ac-coupled termination reference output buffer a cmos buffered copy of the reference input circuit signal is available at the refout pin. this buffer can be optionally powered down by setting register dr2[0], pdrefout to logic 0. pll1 integer-n pll the upper pll in figure 32 , pll1, is an integer-n pll with a loop bandwidth of 140 khz. the input frequency to the pll from the reference circuit is f pfd . the vco frequency, f vco1 , is programmed by setting the value for na, according to f vco1 = f pfd na (3) where na is programmable in the 80 to 131 range. the vco output frequency can tune over the 2.15 ghz to 2.55 ghz range to integer multiples of the pfd input frequency only. by setting each of the vco divider (v0 and v1) and output divider (d0 and d1) values, the vco frequency can be divided down to the required output frequency, independently, for each of the output ports, out0 and out1. the f out0 frequency presented to out0 can be set according to d0v0 na ff pfd out = 0 (4) the frequency f out1 presented to out1 can be set according to 11 1 d v na ff pfd out = (5) the loop filters required for this pll are integrated on chip.
ad9577 data sheet rev. 0 | page 32 of 44 pll1 phase frequency detector (pfd) and charge pump the pfd determines the phase difference error between the reference divider output and the feedback divider output clock edges. the outputs of this circuit are pulse-width modulated up and down signal pulses. these pulses drive the charge pump circuit. the amount of charge delivered from the charge pump to the loop filter is determined by the instantaneous phase error. the action of the closed loop is to drive the frequency and phase error at the input of the pfd toward zero. figure 42 shows a block diagram of the pfd/cp circuitry. d1 q1 clr1 refclk high up d2 q2 clr2 high down cp charge pump 3.3 v gnd feedback divider 09284-047 figure 42. pfd circuit showing simplified charge pump pll1 vco pll1 incorporates a low phase noise lc-tank vco. this vco has 32 frequency bands spanning from 2.15 ghz to 2.55 ghz. at power-up, a vco calibration cycle begins and the correct band is selected based on the feedback divider setting (na). whenever a new feedback divider setting is called for, the vco calibration process must run by writing 1 followed by 0 to the newacq bit, register x0[0]. pll1 feedback divider the feedback divider ratio, na, is used to set the pll1 vco frequency according to equation 3. note that the na value is set by adding the offset value of 80 to the value programmed to register af0[5:0], where 80 is the minimum divider na value. the maximum na value is 131. for example, to set na to 85, the af0[5:0] register is set to 5. setting the output frequency of pll1 for example, set the output frequency (f out0 ) on port 0 to 156.25 mhz, the output frequency (f out1 ) on port 1 to 100 mhz, and both the reference frequency (f ref ) and the pfd frequency (f pfd ) to 25 mhz. the frequency f out0 presented to out0 can be set according to equation 4. the frequency f out1 presented to out1 can be set according to equation 5. to determine if both 156.25 mhz and 100 mhz can be derived from a common f vco1 frequency in the 2.15 ghz to 2.55 ghz range, use the lowest common multiple (lcm) of 156.25 mhz and 100 mhz to determine the lowest vco frequency that can be divided down to provide both of these frequencies. lcm (156.25 mhz, 100 mhz) = 2.5 ghz (6) therefore, set the vco frequency to 2.5 ghz. with f pfd = 25 mhz, from equation 3, na must be set to 100. for 156.25 mhz on port 0, set v0 d0 = 16 (7) this can be achieved by setting v0 to 4 and d0 to 4. for 100 mhz on port 1, set v1 d1 = 25 (8) this can be achieved by setting v1 to 5 and d1 to 5. with a reference frequency of 25 mhz, the reference divider value, r, must be set to 1 by setting register g0[1] to 0. table 22 summarizes the register settings for this configuration. table 22. register settings for example pll1 configuration parameter divide value i 2 c register register value na 100 af0[5:0] 010100 v0 4 adv0[7:5] 100 d0 4 adv0[4:0] 00100 v1 5 adv1[7:5] 101 d1 5 adv1[4:0] 00101 r 1 g0[1] 1 pll2 integer/fractional-n pll the lower pll in figure 32 , pll2, is a fractional-n pll. the input frequency to the pll from the reference circuit is f pfd . the vco frequency, f vco2 , is programmed by setting the values for nb, frac, and mod according to ) ( 2 m od frac nbff pfd vco += (9) where nb is programmable in the 80 to 131 range. to provide the greatest flexibility and accuracy, both the frac and mod values can be programmed to a resolution of 12 bits, where frac < mod. the vco output frequency can tune over the 2.15 ghz to 2.55 ghz range to fractional multiples of the pfd input frequency. by setting each of the vco divider (v2 and v3) and output divider (d2 and d3) values, the vco frequency can be divided down to the required output frequency, independently, for each of the output ports, out2 and out3. the f out2 frequency presented to out2 can be set according to d2v2 mod frac nb ff pfd out2 + = ) ( (10)
data sheet ad9577 rev. 0 | page 33 of 44 the f out3 frequency presented to out3 can be set according to d3v3 mod frac nb ff pfd out3 + = ) ( (11) the loop filters required for this pll are integrated on chip. by setting the frac value to 0, powering down the sdm by setting register abf0[4] to 1, and turning the bleed current off by setting register bp0[2] = 0, pll2 can operate as an integer-n pll. equation 10 and equation 11 are still used to set the output frequencies for f out2 and f out3 . operation in this mode provides improved performance in terms of phase noise, spurs, and jitter. pll2 phase frequency detector (pfd) and charge pump the pll2 pfd and charge pump is the same as that described in the pll1 phase frequency detector (pfd) and charge pump section. when operating in fractional-n mode, a charge pump bleed current should be enabled to linearize the pll transfer function and, therefore, to minimize spurs due to the operation of the - modulator. bleed is enabled by setting register bp0[2]. pll2 loop bandwidth the normal pll loop bandwidth is 50 khz. when the sscg input pin is asserted, the loop bandwidth switches from 50 khz to 125 khz, which prevents the triangle-wave modulation waveform from being overly filtered by the pll. when the max_bw input pin is set high, it forces the pll bandwidth to be 250 khz instead of 125 khz. pll2 vco pll2 incorporates a low phase noise lc-tank vco. this vco has 32 frequency bands spanning from 2.15 ghz to 2.55 ghz. at power-up, a vco calibration cycle begins and the correct band is selected based on the feedback divider setting (nb). whenever a new feedback divider setting is called for, the vco calibration process must run by writing 1 followed by 0 to the newacq bit, register x0[0]. pll2 feedback divider the nb feedback divider ratio is used to set the pll2 vco frequency according to equation 9. note that the nb value is set by adding the decimal value programmed to register bf3[5:0] to a decimal value of 80, where the minimum divider nb value is 80. the maximum nb value is 131. for example, to set nb to 85, register bf3[5:0] is set to 5. pll2 - modulator when operating in fractional-n mode only, pll2 uses a third- order, multistage noise shaping (mash) - modulator (sdm) to adjust the feedback divider ratio. the programmed nb value can be adjusted over the ?4 to +3 range on every rising clock edge from the feedback divider output (typically 25 mhz for networking applications). in this way, the average feedback divide ratio is adjusted to be a noninteger value, allowing for a vco frequency that is a fractional multiple of the pfd frequency to be synthesized. by setting the frac and mod values of the sdm, the pll2 vco frequency can be set according to equation 9. the sdm must be turned on by setting pd_sdm to 0, register abf0[4]. 12-bit programmable modulus (mod) and fractional (frac) values unlike most other fractional-n plls, the ad9577 allows users to program the modulus over a 12-bit range, which means they can set up the part in many different configurations. it also usually means that, in most applications, it is possible to design the pll to achieve the desired output frequency multiplication with 0 ppm frequency error. the mod value is set by setting register bf1[3:0] and register bf2[7:0]. the frac value is set by setting register bf0[7:0] and register bf1[7:4]. bleed current when the sdm is operational (register abf0[4] set to 0), bleed current should be enabled (register bp0[2] set to 1), which increases the in-band phase noise but reduces the fractional spur amplitudes. all fractional-n jitter data is reported with bleed = 1. if bleed = 0 in fractional-n mode, the rms jitter decreases significantly; however, the fractional spur amplitudes increase. when pll2 operates in integer-n mode, the bleed current should be disabled to improve the plls in-band phase noise. spur mechanisms this section describes the three different spur mechanisms that arise with a fractional-n pll: fractional spurs, integer boundary spurs, and reference spurs. fractional spurs the fractional interpolator in the ad9577 is a third-order sdm with a modulus that is programmable to any integer value from 50 to 4095. the sdm is clocked at the pfd reference rate (f pfd ) that allows pll output frequencies to be synthesized at a channel step resolution of f pfd /mod. the quantization noise from the - modulator appears as fractional spurs. the interval between spurs is f pfd /l, where l is the repeat length of the code sequence in the digital - modulator. for the third-order modulator used in the ad9577 , the repeat length depends on the value of mod, as listed in table 23 . table 23. fractional spur frequencies condition repeat length spur interval if mod is divisible by 2, but not 3 2 mod f pfd /(2 mod) if mod is divisible by 3, but not 2 3 mod f pfd /(3 mod) if mod is divisible by 6 6 mod f pfd /(6 mod) otherwise mod f pfd /mod
ad9577 data sheet rev. 0 | page 34 of 44 integer boundary spurs another mechanism for fractional spur creation is the interactions between the rf vco frequency and the reference frequency. when these frequencies are not integer related (the point of a fractional-n synthesizer), spur sidebands appear on the vco output spectrum at an offset frequency that corresponds to the beat note or difference frequency, between an integer multiple of the reference and the vco frequency. these spurs are attenuated by the loop filter and are more noticeable on channels close to integer multiples of the reference where the difference frequency can be inside the loop bandwidth; therefore, the name integer boundary spurs. reference spurs reference spurs occur for both integer-n and fractional-n operation. reference spurs are generally not a problem in fractional-n synthesizers because the reference offset is far outside the loop bandwidth. however, any reference feed- through mechanism that bypasses the loop may cause a problem. feedthrough of low levels of on-chip reference switching noise, through the reference input or output pins back to the vco, can result in noticeable reference spur levels. in addition, coupling of the reference frequency to the output clocks can result in beat note spurs. pcb layout needs to ensure adequate isolation between vco/ldo supplies, the output traces, and the input or output reference to avoid a possible feedthrough path on the board. if the reference output clock (refclk) is not required, it should be powered down to minimize potential board coupling. the sdm digital circuitry is clocked by the reference clock. the sdm is enabled when pll2 is in fractional-n mode. when pll2 is in fractional-n mode, the switching noise at the reference frequency may result in increased spurs levels at the outputs. optimizing pll performance because the ad9577 can be configured in many ways, some guide- lines should be followed to ensure that the high performance is maintained. for both plls, there can be a small advantage in choosing a lower vco frequency because the vco phase noise tends to be slightly better at lower frequencies. both vcos should not operate at the same frequency because this degrades jitter performance. the two vco frequencies should differ by at least 2 mhz. the following guidelines apply to pll2 operating in fractional-n mode only. if possible, denominators that have factors of 2, 3, or 6 should be avoided because they can produce slightly higher subfractional spur components. avoid low and high fractions (that is, frac/mod close to 1/mod or (mod ? 1)/ mod) because these are more susceptible to larger fractional spur components and integer boundary spurs. avoid creating a low valued beat frequency between the output frequency and the pfd frequency to minimize the risk of low offset beat frequency spurs. for example, setting f pfd = 25 mhz, and f out = 100.01 mhz can create an output spur at 10 khz offset to 100.01 mhz, depending on board layout. choosing a smaller mod value results in fractional spurs that are at a higher frequency and, consequently, are better filtered by the pll loop filter bandwidth of 50 khz. setting the output frequency of pll2 for example, to set the output frequency (f out2 ) on port 2 to 155.52 mhz and the output frequency (f out3 ) on port 3 to 38.88 mhz using a reference frequency (f ref ) and pfd frequency (f pfd ) of 25 mhz, do the following. the frequency f out2 presented to out2 can be set according to equation 10. the frequency f out3 presented to out3 can be set according to equation 11. in this case, both 155.52 mhz and 38.88 mhz can be derived from the same vco frequency because they are related by a factor of 4. the next step is to determine what the required values of f vco2 , v2, and d2 are to divide down to 155.52 mhz. table 24 shows the available options. table 24. suitable values of f vco2 and v2 d2, to achieve f out2 = 155.52 mhz f out2 (mhz) v2 d2 f vco2 (ghz) 155.52 14 2.17728 155.52 15 2.3328 155.52 16 2.48832 choose a f vco2 value of 2.48832 ghz. next, determine that the multiplication ratio (nb + frac/mod) required to multiply a f pfd of 25 mhz up to 2.48832 ghz is 99.5328. therefore, nb must be set to 99 and (frac/mod) = 0.5328. to convert 0.5328 to a fraction, 0.5328 can be the same as 5328/10000. this fraction can then be reduced to the lowest terms by dividing both the numerator and denominator by 16, where 16 is the greatest common divisor (gcd) of the 5328 and 10,000. this results in a solution for frac/mod = 333/625. for 155.52 mhz on port 2, set v2 d2 = 16. this can be achieved by setting v2 to 4 and d2 to 4. for 38.88 mhz on port 3, set v3 d3 = 64. this can be achieved by setting v3 to 4 and d3 to 16. with a reference frequency of 25 mhz, the reference divider value, r, must be set to 1 by setting register g0[1] to 0. because both channels use vco divide values of 4on v2 and v3, syncch23, register bdv2[0], can be set to 1 to ensure that the clock edges on port 2 and port 3 are synchronized. table 25 summarizes the register setting for this configuration. table 25. registers setting for example pll2 configuration parameter value i 2 c register register value nb 99 bf3[5:0] 010011 frac 333 bf0[7:0], bf1[7:4] 000101001101 mod 625 bf1[3:0], bf2[7:0] 001001110001 v2 4 bdv0[7:5] 100 d2 4 bdv0[4:0] 00100 v3 4 bdv1[7:5] 100 d3 16 bdv1[4:0] 10000 r 1 g0[1] 0000 syncch23 1 bdv2[0] 1
data sheet ad9577 rev. 0 | page 35 of 44 margining by asserting the margin pin, a second full frequency map can be applied to the output ports. the values for the na, v0, d0, v1, and d1 parameters, and the nb, frac, mod, v2, d2, v3, d3 parameters must be programmed over the i 2 c, although default values exist. there are some limitations: the output buffer signal formats cannot be changed, and the pll2 fractional-n settings, such as power-down of the sdm, and bleed settings cannot be changed. the margining feature can be used to set higher than nominal frequencies on each of the ports to test system robustness. when the margin pin signal level is changed, a new frequency acquisition is performed. spread spectrum clock generation (sscg) by asserting the sscg (spread spectrum clock generator) pin, pll2 operates in spread spectrum mode, and the output frequency modulates with a triangular profile. as the clock signal energy spreads out over a range of frequencies, it reduces the peak power at any one frequency when observed with a spectrum analyzer through a resolution bandwidth filter. this result improves the radiated emissions from the part and from the devices that receive its clock. t he triangular-wave modulation is implemented by controlling the divide ratio of the feedback divider. this is achieved by ramping the fractional word to the sdm. figure 43 shows an example implementation. the pfd frequency, f pfd , is 25 mhz. the starting vco frequency, f vco , is 25 mhz (99 + 3072/4096), giving 2.49375 ghz. by continuously ramping the frac word down and up, this frequency is periodically reduced to 25 mhz (99 + 1029/4096) = 2.481281 ghz. this results in a triangular frequency modulation profile, with a peak downspread (that is, peak percentage frequency reduction) of ?0.5%. by controlling the step size, number of steps, and the step rate, the modulation frequency is adjusted. f pfd f pfd vco 2.15ghz to 2.55ghz pfd/cp third order lpf divide by 80 to 131 feedback divider n b sdm 3-bit 0 1 frac frac_triwave sscg mod ckdiv frac fracstep numsteps sscg triwave generator frac_triwave f vco f vco ? 0.5% time vco frequency time frac_triwave = 3072 frac_triwave = 1029 09284-048 figure 43. spread spectrum clock generator with triangular wave modulation, f pfd = 25 mhz basic spread spectrum programming the sscg is highly programmable; however, most applications require that the frequency modulation rate be between 30 khz and 33 khz and that the peak frequency deviation be ?0.5% downspread. the ad9577 supports downspread only, with a maximum deviation of ?0.5%. the key parameters (which are not themselves registers) that define the frequency modulation profile include the following: ? f mod , which is the frequency of the modulation waveform. ? fracrange, which determines the peak frequency deviation by setting the maximum change in the frac value from the nominal. t he following equations determine the value of these parameters: f racrange = fracstep numsteps (12) ckdiv numsteps f f pfd mod = 2 (13) where the following are programmable registers: ? numsteps is the number of fractional word steps in half the triwave period. ? fracstep is the value of the fractional word increment/ decrement, while traversing the tri-wave. ? ckdiv is the integer value by which the reference clock frequency is divided to determine the update rate of the triangular-wave generator, that is, the step update rate. ? f pfd is the pfd frequency.
ad9577 data sheet rev. 0 | page 36 of 44 table 27. ckdiv and fracstep values used in worked example ckdiv ideal fracstep rounded fracstep table 26 shows the relevant register names and programmable ranges. table 26. registers used to program sscg operation parameter fracstep error 2 ?1.5675 ?2 21.6% register name range numsteps 3 ?2.35125 ?2 17.6% bs2[7:0], bs3[7] +1 to +511 fracstep 4 ?3.135 ?3 4.5% bs1[7:0] ?128 to 0 5 ?3.91875 ?4 2.0% ckdiv bs3[6:0] +2 to +127 6 ?4.7025 ?5 6.0% 7 ?5.48625 ?5 9.7% because the register values need to be expressed as integers, there are no guaranteed exact solutions; therefore, some approximations and trade-offs must be made. the fact that neither fracrange nor f mod needs to be exact is exploited. note that the sscg pin must be toggled every time the sscg parameters are adjusted for the changes to take effect. 8 ?6.27 ?6 4.5% 9 ?7.05375 ?7 0.77% 10 ?7.8375 ?8 2.0% both ckdiv and numsteps must be integers. to minimize error, ckdiv = 9 and fracstep = ?7 was chosen. with a target for fracrange = ?313.5, equation 12 is used to find the ideal value of numsteps = 44.79, which is rounded to 45. from equation 12, the actual used value for fracrange is worked example: programming for f mod = 31.25 khz, downspread = ?0.5%, f pfd = 25 mhz assume nb = 100, mod = 625, and frac = 198. in addition, a large number of frequency steps are desired to cover ?0.5%. the objective is to find values for fracstep, numsteps, and ckdiv that result in the required frequency modulation profile. fracrange = ?7 45 = ?315 the accuracy of this solution needs to be verified. putting the derived values into equation 13 gives the total feedback divider ratio is khz30.86 9452 mhz25 2 = = = n tot = nb + m od frac = 100 + 198/625 = 62,698/625 fracrange is set to ?0.5% of 62,698, which results in an ideal value of ?313.5. by rearranging equation 12 and equation 13, it results in ? ? ? ? ? ? ? ? = 2 (14) in addition, the percentage frequency deviation is obtained as %502.0 625 62698 625 315100 100 ?= ? = = the f mod and the percentage frequency deviation are very close to the target values. the register settings required for this example are detailed in table 29 . putting in the values for fracrange, f mod , and f pfd from the previous information, the following results: fracstep = ckdiv (?0.78375) (15) sscg register summary an approximate solution must be found to equation 15 that produces an integer value for ckdiv, which gives a value that is very close to an integer for fracstep. in this case, considering ckdiv values in the range of 2 to 10 gives the fracstep values shown in table 27 . table 28 summarizes the programmable registers required to set up sscg. table 28. register values for sscg parameter register names range numsteps bs2[7:0], bs3[7] +1 to +511 fracstep bs1[7:0] ?128 to 0 ckdiv bs3[6:0] +2 to +127 frac bf0[7:0], bf1[7:4] 0 to +4094 mod bf1[3:0], bf2[7:0] 0 to +4095 nb bf3[5:0] 0 to +51
data sheet ad9577 rev. 0 | page 37 of 44 max_bw the normal bandwidth of pll2 is 50 khz. this low bandwidth is required to filter the sdm phase noise. when sscg is activated, the bandwidth is increased to 125 khz. there is a trade-off in setting the pll bandwidth between allowing the triangular-wave modulation (that is, its higher order harmonics) to pass through the pll unattenuated and passing more sdm phase noise through to the pll output. bringing the max_bw pin high changes the pll bandwidth to 250 khz from its default value of 125 khz during sscg operation. increasing the pll bandwidth results in more sdm phase noise being passed unfiltered through to the pll output, but more of the triangular-wave harmonics are also passed through, improving the triangular-wave accuracy. table 29. register values for sscg example parameter register name range value (decimal) value(binary) numsteps bs2[7:0], bs3[7] +1 to +511 +45 00101101 fracstep bs1[7:0] ?128 to 0 ?7 11111001 ckdiv bs3[6:0] +2 to +127 +9 0001001 frac bf0[7:0], bf1[7:4] 0 to +4094 +198 000011000110 mod bf1[3:0], bf2[7:0] 0 to +4095 +625 001001110001 nb bf3[5:0] 0 to +63 80 + 20 = 100 010100
ad9577 data sheet rev. 0 | page 38 of 44 i 2 c interface timing and internal register description 1 0 0 0 0 0 0 x slave address [6:0] r/w ctrl 0 = wr 1 = rd 09284-049 figure 44. slave address configuration s slave addr, lsb = 0 (wr) a(s) a(s) a(s) data sub addr a(s) p data 09284-050 figure 45. i 2 c write data transfer s s = start bit p = stop bit a(s) = acknowledge by slave a(m) = acknowledge by master a(m) = lack of acknowledge by master s slave addr, lsb = 0 (wr) slave addr, lsb = 1 (rd) a(s) a(s) sub addr a(s) data a(m) data p a(m) 09284-051 figure 46. i 2 c read data transfer start bit s stop bit p ack ack wr ack d0 d7 a0 a7 a5 a6 sladdr[4:0] slave address sub address data sub addr[6:1] data[6:1] scl sda 09284-052 figure 47. i 2 c data transfer timing t buf sda ss scl t f t low t r t f t hd;sta t hd;dat t su;dat t high t su;sta t su;sto t hd;sta t r 09284-053 p s figure 48. i 2 c port timing diagram
data sheet ad9577 rev. 0 | page 39 of 44 table 30. internal register map register name r/w addr d7 d6 d5 d4 d3 d2 d1 d0 c0 w 0x40 0 0 0 0 0 0 eni2c 0 x0 w 0x1f 0 0 0 0 0 0 0 newacq bp0 w 0x11 0 0 0 0 0 bleed pdch1 pdch0 af0 w 0x18 0 0 na[5:0], pll1 feedback divider ratio bf3 w 0x1c 0 0 nb[5:0], pll2 feedback divider ratio bf0 w 0x19 frac[11:4], sdm fractional word bf1 w 0x1a frac[3:0], sdm fractional word mod[11:8], sdm modulus bf2 w 0x1b mod[7:0], sdm modulus abf0 w 0x1d 1 1 0 pd_sdm 0 0 0 0 adv0 w 0x22 v0[2:0], channel 0 vco divider d0[4:0], channel 0 output divider value adv1 w 0x23 v1[2:0], channel 1 vco divider d1[4:0], channel 1 output divider value adv2 w 0x24 0 0 0 0 0 0 0 syncch01 bdv0 w 0x25 v2[2:0], channel 2 vco divide r d2[4:0], channel 2 output divider value bdv1 w 0x26 v3[2:0], channel 3 vco divide r d3[4:0], channel 3 output divider value bdv2 w 0x27 0 0 0 0 0 0 0 syncch23 bs1 w 0x2a fracstep[7:0], sscg fractional step size bs2 w 0x2b numsteps[8:1], number of fractional word increments/decrements per half triangular-wave cycle bs3 w 0x2c numsteps[0] ckdiv[6:0], reference divider output is divided by this integer to determine sscg update rate am0 w 0x30 0 0 na[5:0], pll1 feedback divider ratio divider; margin = 1 am1 w 0x31 v0[2:0], channel 0 vco divider; margin = 1 d0[4:0], channel 0 output divider value; margin = 1 am2 w 0x32 v1[2:0], channel 1 vco divider; margin = 1 d1[4:0], channel 1 output divider value; margin = 1 bm0 w 0x33 0 0 nb[5:0], pll2 feedback divider ratio divider; margin = 1 bm1 w 0x34 frac[11:4], sdm fractional word; margin = 1 bm2 w 0x35 frac[3:0], sdm fractional word; margin = 1 mod[11:8], sdm modulus; margin = 1 bm3 w 0x36 mod[7:0], sdm modulus; margin = 1 bm4 w 0x37 v3[2:0], channel 3 vco divider; margin = 1 d3[4:0], channel 3 output divider value; margin = 1 bm5 w 0x38 v2[2:0], channel 2 vco divider; margin = 1 d2[4:0], channel 2 output divider value; margin = 1 dr1 w 0x3a pdch3 pdch2 format2[2:0], output format selection for pll2 (see table 21 ) format1[2:0], output format selection for pll1 (see table 20 ) dr2 w 0x3b 0 0 0 0 0 0 0 pdrefout g0 w 0x3d 0 0 0 0 pdpll1, power- down pll1 pdpll2, power- down pll2 r; 0 = divide by 1 0
ad9577 data sheet rev. 0 | page 40 of 44 default frequency map and output formats the power-up operation (without i 2 c programming) of the ad9577 is represented by a default frequency map and output formats (see table 31 ). table 31. default parameter values, f pfd = 25 mhz parameter value notes pll1 f out0 = 156.25 mhz, f out1 = 125 mhz na 80 + 20 = 100 v0 4 d0 4 v1 4 d1 5 format1 000 out0/out1 are lvpecl syncch01 0 pll2 f out2 = 100 mhz, f out3 = 33.333 mhz nb 80 + 16 = 96 frac 0 mod 0 pd_sdm 1 bleed 0 v2 4 d2 6 v3 4 d3 18 format2 000 out2/out3 are lvpecl syncch23 0 sscg fracstep 0 numsteps 0 ckdiv 0 control eni2c 0 newacq 0 pdch0 0 pdch1 0 pdch2 0 pdch3 0 pdrefout 0 pdpll1 0 pdpll2 0 r 0 parameter value notes margining these parameters are applied only when the margin pin = high pll1 f out0 = 156.25 mhz, f out1 = 125 mhz na 80 + 20 = 100 v0 4 d0 4 v1 4 d1 5 f out0 156.25 mhz f out1 125 mhz pll2 f out2 = 212.5 mhz, f out3 = 106.25 mhz nb 80 + 22 = 102 frac 0 mod 0 v2 2 d2 6 v3 4 d3 6 i 2 c interface operation the ad9577 is programmed by a 2-wire, i 2 c-compatible serial bus driving multiple peripherals. two inputs, serial data (sda) and serial clock (scl), carry information between any devices connected to the bus. each slave device is recognized by a unique address. the slave address consists of the 7 msbs of an 8-bit word. the 7-bit slave address of the ad9577 is 1000000. the lsb of the word sets either a read or write operation (see figure 44 ). logic 1 corresponds to a read operation, and logic 0 corresponds to a write operation. to control the device on the bus, do the following protocol. first, the master initiates a data transfer by establishing a start condition, defined by a high-to-low transition on sda while scl remains high, which indicates that an address/data stream follows. all peripherals respond to the start condition and shift the next eight bits (the 7-bit address and the r/ w bit). the bits are transferred from msb to lsb. the peripheral that recognizes the transmitted address responds by pulling the data line low during the ninth clock pulse, which is known as the acknowledge bit. all other devices withdraw from the bus at this point and maintain an idle condition. the idle condition is where the device monitors the sda and scl lines waiting for the start condition and correct transmitted address. the r/ w bit determines the direction of the data. logic 0 on the lsb of the first byte means that the master writes information to the peripheral, and logic 1 on the lsb of the first byte means that the master reads information from the peripheral.
data sheet ad9577 rev. 0 | page 41 of 44 th e ad9577 acts as a standard slave device on the bus. the data on the sda pin is eight bits long supporting the 7-bit addresses plus the r/ w bit. the has 31 subaddresses to enable the user-accessible internal registers (see ). therefore, it interprets the first byte as the device address and the second byte as the starting subaddress. auto-increment mode is supported, which allows data to be read from or written to the starting subaddress and each subsequent address without manually addressing the subsequent subaddress. a data transfer is always terminated by a stop condition. the user can also access any unique subaddress register on a one-by-one basis without updating all registers. ad9577 table 30 stop and start conditions can be detected at any stage of the data transfer. if these conditions are asserted out of sequence with normal read and write operations, they cause an immediate jump to the idle condition. during a given scl high period, one start condition, one stop condition, or a single stop condition followed by a single start condition should be issued. if an invalid subaddress is issued, the ad9577 does not issue an acknowledge and returns to the idle condition. if the highest subaddress is exceeded while reading back in auto-increment mode, the highest subaddress register contents continue to be output until the master device issues a no acknowledge, which indicates the end of a read. in a no acknowledge condition, the sda line is not pulled low on the ninth pulse. see figure 45 and figure 46 for sample read and write data transfers, and see figure 47 for a more detailed timing diagram. to overwrite any of the default register values, complete the following steps: 1. enable the overwriting of registers by setting eni2c, register c0[1]. 2. only write to registers that need modification from their default value. 3. after all the registers have been set, a new acquisition is initiated by toggling newacq, register x0[0] from low to high to low. an example set of i 2 c commands follows. these enable the i 2 c registers and program the output frequencies of both plls. f pfd is 25 mhz. a leading w represents a write command. table 32. i 2 c programming example register writes write/read register name data (hex) operation w c0 02 enable i 2 c registers w af0 0a na = 80 + 10 = 90; f vco1 = 2.25 ghz w adv0 a6 channel 0 divides by 5 6 = 30; f out0 = 75 mhz w adv1 cc channel 1 divides by 6 12 = 72; f out1 = 31.25 mhz w bf3 15 nb = 80 + 21 = 101; f vco2 = 2.53832 ghz w bf0 14 frac = 333 w bf1 d2 frac = 333, mod = 625 w bf2 71 mod = 625 w abf0 c0 power-up sdm, release sdm reset w bp0 04 turn on bleed w bdv0 44 channel 2 divides by 2 4 = 8; f out2 = 317.29 mhz w bdv1 b0 channel 3 divides by 5 16 = 80; f out3 = 31.729 mhz w x0 01 force new acquisition by toggling newacq w x0 00
ad9577 data sheet rev. 0 | page 42 of 44 typical application circuits 100 ? differential transmission line 100 ? differential transmission line 100 ? differential transmission line 1 10 vsca vsi2c refout vsrefout vsx refclk xt2 xt1 refsel vscb 30 21 out3p vsfb vsm sscg vsfa out1n out1p vsob1a out3n vsob3b 11 20 tst1b tst2b ldo gnd out2n gnd out2p vsob2b margin vsvb out0n out0p gnd gnd scl vsva tst2a 40 max_bw vsob0a 31 sda ad9577 22pf 22pf c d c d v s v s v s v s v s v s v s v s c d c d 220nf c d c d r t = 100 ? r t = 100 ? 100 ? differential transmission line r t = 100 ? r t = 100 ? v s v s v s v s v s do not connect other traces to pin 15, pin 16, pin 35, and pin 36. capacitors c d consist of 100nf in parallel with 10nf. 10k ? v s 10k ? v s 09284-054 c d c d figure 49. typical lvds application circuit
data sheet ad9577 rev. 0 | page 43 of 44 1 10 vsca vsi2c refout vsrefout vsx refclk xt2 xt1 refsel vscb 30 21 out3p vsfb vsm sscg vsfa out1n out1p vsob1a out3n vsob3b 11 20 tst1b tst2b ldo g nd out2n gnd out2p v sob2b margin vsvb out0n o ut0p gnd gnd scl vsva tst2a 40 max_bw vsob0a 31 sda ad9577 22pf 22pf c d c d v s v s v s v s v s v s v s v s c d c d 220nf c d c d v s v s v s v s v s do not connect other traces to pin 15, pin 16, pin 35, and pin 36. capacitors c d consist of 100nf in parallel with 10nf. 10k ? v s 10k ? v s 50? 50? 50? 50? 50? 50? v s 127 ? 83 ? 127 ? 83 ? v s 127 ? 83 ? 127 ? 83 ? v s 127 ? 83? 127 ? 83 ? 50? 50? v s 127 ? 83? 127 ? 83 ? 09284-055 c d c d figure 50. typical lvpecl application circuit power and grounding considerations and power supply rejection many applications seek high speed and performance under less than ideal operating conditions. in these application circuits, the implementation and construction of the pcb is as important as the circuit design. proper rf techniques must be used for device selection, placement, and routing, as well as for power supply bypassing and grounding to ensure optimum performance. each power supply pin should have independent decoupling and connections to the power supply plane. it is recommended that the device exposed paddle be directly connected to the ground plane by a grid of at least nine vias. care should be taken to ensure that the output traces cannot couple onto the reference or crystal input circuitry.
ad9577 data sheet rev. 0 | page 44 of 44 outline dimensions 02-02-2010-a 0.50 bsc bottom view top view pin 1 indicator exposed pad p i n 1 i n d i c a t o r seating plane 0.05 max 0.02 nom 0.20 ref coplanarity 0.08 0.30 0.25 0.18 6.10 6.00 sq 5.90 0.80 0.75 0.70 for proper connection of the exposed pad, refer to the pin configuration and function descriptions section of this data sheet. 0.45 0.40 0.35 0.20 min * 4.70 4.60 sq 4.50 compliant to jedec standards mo-220-wjjd-5 with exception to exposed pad dimension. 40 1 11 20 21 30 31 10 figure 51. 40-lead lead frame chip scale package [lfcsp_wq] 6 mm 6 mm body, very very thin quad (cp-40-7) dimensions shown in millimeters ordering guide model 1 temperature range package description package option ordering quantity ad9577bcpz ?40c to +85c 40-lead lfcsp_wq cp-40-7 ad9577bcpz-rl ?40c to +85c 40-lead lfcsp_wq, 13 tape reel cp-40-7 2,500 ad9577bcpz-r7 ?40c to +85c 40-lead lfcsp_wq, 7 tape reel cp-40-7 750 AD9577-EVALZ evaluation board 1 z = rohs compliant part. i 2 c refers to a communications protocol originally developed by philips semiconductors (now nxp semiconductors). ?2011 analog devices, inc. all rights reserved. trademarks and registered trademarks are the prop erty of their respective owners. d09284-0-10/11(0)

▲Up To Search▲

Price & Availability of AD9577-EVALZ

	To Download AD9577-EVALZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .