View AD8031_7235900.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

16-bit, 250 ksps pulsar adc in msop/qfn ad7685 rev. c information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2004C2011 analog devices, inc. all rights reserved. features 16-bit resolution with no missing codes throughput: 250 ksps inl: 0.6 lsb typical, 2 lsb maximum (0.003% of fsr) sinad: 93.5 db @ 20 khz thd: ?110 db @ 20 khz pseudo differential analog input range 0 v to v ref with v ref up to vdd no pipeline delay single-supply operation 2.3 v to 5.5 v with 1.8 v to 5 v logic interface serial interface spi?-/qspi?-/microwire?-/dsp-compatible daisy-chain multiple adcs, busy indicator power dissipation 1.4 w @ 2.5 v/100 sps 1.35 mw @ 2.5 v/100 ksps, 4 mw @ 5 v/100 ksps standby current: 1 na 10-lead package: msop (msop-8 size) and 3 mm 3 mm qfn (lfcsp) (sot-23 size) pin-for-pin-compatible with 10-lead msop/qfn pulsar? adcs applications battery-powered equipment medical instruments mobile communications personal digital assistants (pdas) data acquisition instrumentation process controls 02968-005 code 65536 0 16384 32768 49152 inl (lsb) 2.0 1.5 1.0 0.5 0 ?0.5 ?1.0 ?1.5 ?2.0 positive inl = +0.33lsb negative inl = ?0.50lsb figure 1. integral nonlinearity vs. code. application diagram ad7685 ref gnd vdd in+ in? vio sdi sck sdo cnv 1.8v to vdd 3- or 4-wire interface (spi, daisy chain, cs) 0.5 v to vdd 2.5 v to 5v 0 to vref 02968-001 figure 2. table 1. msop, qfn (lfcsp)/sot-23 14-/16-/18-bit pulsar adc type 100 ksps 250 ksps 400 ksps to 500 ksps 1000 ksps adc driver 18-bit true ad7691 ad7690 ad7982 ada4941 differential ad7982 ada4841 16-bit true ad7684 ad7687 ad7688 ada4941 differential ad7693 ada4841 16-bit pseudo ad7680 ad7685 ad7686 ad7980 ada4841 differential ad7683 ad7694 14-bit pseudo ad7940 ad7942 ad7946 ada4841 differential general description the ad7685 is a 16-bit, charge redistribution successive approximation, analog-to-digital converter (adc) that operates from a single power supply, vdd, between 2.3 v to 5.5 v. it contains a low power, high speed, 16-bit sampling adc with no missing codes, an internal conversion clock, and a versatile serial interface port. the part also contains a low noise, wide bandwidth, short aperture delay, track-and-hold circuit. on the cnv rising edge, it samples an analog input in+ between 0 v to ref with respect to a ground sense in?. the reference voltage, ref, is applied externally and can be set up to the supply voltage. power dissipation scales linearly with throughput. the spi-compatible serial interface also features the ability, using the sdi input, to daisy chain several adcs on a single 3-wire bus or provides an optional busy indicator. it is compatible with 1.8 v, 2.5 v, 3 v, or 5 v logic using the separate supply vio. the ad7685 is housed in a 10-lead msop or a 10-lead qfn (lfcsp) with operation specified from ?40c to +85c.
ad7685 rev. c | page 2 of 28 table of contents features .............................................................................................. 1 ? applications....................................................................................... 1 ? application diagram........................................................................ 1 ? general description ......................................................................... 1 ? revision history ............................................................................... 2 ? specifications..................................................................................... 3 ? timing specifications....................................................................... 5 ? absolute maximum ratings............................................................ 7 ? esd caution.................................................................................. 7 ? pin configuration and function descriptions............................. 8 ? terminology ...................................................................................... 9 ? typical performance characteristics ........................................... 10 ? theory of operation ...................................................................... 13 ? circuit information.................................................................... 13 ? converter operation.................................................................. 13 ? typical connecti on diagram ................................................... 14 ? analog inputs.............................................................................. 15 ? driver amplifier choice ........................................................... 16 ? voltage reference input ............................................................ 16 ? power supply............................................................................... 16 ? supplying the adc from the reference.................................. 17 ? digital interface.......................................................................... 17 ? cs mode 3-wire, no busy indicator..................................... 18 ? cs mode 3-wire with busy indicator ................................... 19 ? cs mode 4-wire, no busy indicator..................................... 20 ? cs mode 4-wire with busy indicator ................................... 21 ? chain mode, no busy indicator ............................................ 22 ? chain mode with busy indicator........................................... 23 ? application hints ........................................................................... 24 ? layout .......................................................................................... 24 ? evaluating the performance of the ad7685............................... 24 ? true 16-bit isolated application example .............................. 25 ? outline dimensions ....................................................................... 26 ? ordering guide .......................................................................... 27 ? revision history 8/11rev. b to rev. c changes to figure 6 and table 7..................................................... 8 updated outline dimensions ....................................................... 26 changes to ordering guide .......................................................... 27 3/07rev. a to rev. b changes to features and table 1 .................................................... 1 changes to table 3............................................................................ 4 moved figure 3 and figure 4 to page............................................. 6 inserted figure 6; renumbered sequentially................................ 8 changes to figure 13 and figure 14............................................. 11 changes to figure 27...................................................................... 14 changes to table 9.......................................................................... 16 changes to figure 32...................................................................... 17 changes to figure 43...................................................................... 22 changes to figure 45...................................................................... 23 updated outline dimensions ....................................................... 26 changes to ordering guide .......................................................... 27 12/04rev. 0 to rev. a changes to specifications.................................................................3 changes to figure 17 captions..................................................... 11 changes to power supply section ................................................ 17 changes to digital interface section ........................................... 18 changes to cs mode 4-wire no busy indicator section ......... 21 changes to cs mode 4-wire with busy indicator section....... 22 changes to chain mode, no busy indicator section................ 23 changes to chain mode with busy indicator section .............. 24 added true 16-bit isolated application example section ....... 26 added figure 47 ............................................................................. 26 changes to ordering guide .......................................................... 28 4/04revision 0: initial revision
ad7685 rev. c | page 3 of 28 specifications vdd = 2.3 v to 5.5 v, vio = 2.3 v to vdd, v ref = vdd, t a = C40c to +85c, unless otherwise noted. table 2. a grade b grade c grade parameter conditions min typ max min typ max min typ max unit resolution 16 16 16 bits analog input voltage range in+ ? in? 0 v ref 0 v ref 0 v ref v absolute input voltage in+ ?0.1 vdd + 0.1 ?0.1 vdd + 0.1 ?0.1 vdd + 0.1 v in? ?0.1 +0.1 ?0.1 +0.1 ?0.1 +0.1 v analog input cmrr f in = 250 khz 65 65 65 db leakage current at 25c acquisition phase 1 1 1 na input impedance see the analog inputs section see the analog inputs section see the analog inputs section accuracy no missing codes 15 16 16 bits differential linearity error ?1 0.7 ?1 0.5 +1.5 lsb 1 integral linearity error ?6 +6 ?3 1 +3 ?2 0.6 +2 lsb transition noise ref = vdd = 5 v 0.5 0.5 0.45 lsb gain error 2 , t min to t max 2 30 2 30 2 15 lsb gain error temperature drift 0.3 0.3 0.3 ppm/c offset error 2 , t min to t max vdd = 4.5 v to 5.5 v 0.1 1.6 0.1 1.6 0.1 1.6 mv vdd = 2.3 v to 4.5 v 0.7 3.5 0.7 3.5 0.7 3.5 mv offset temperature drift 0.3 0.3 0.3 ppm/c power supply sensitivity vdd = 5 v 5% 0.05 0.05 0.05 lsb throughput conversion rate vdd = 4.5 v to 5.5 v 0 250 0 250 0 250 ksps vdd = 2.3 v to 4.5 v 0 200 0 200 0 200 ksps transient response full-scale st ep 1.8 1.8 1.8 s ac accuracy signal-to-noise ratio f in = 20 khz, v ref = 5 v 90 90 92 91.5 93.5 db 3 f in = 20 khz, v ref = 2.5 v 86 86 88 87.5 88.5 db spurious-free dynamic range f in = 20 khz ?100 ?106 ?110 db total harmonic distortion f in = 20 khz ?100 ?106 ?110 db signal-to-(noise + distortion) f in = 20 khz, v ref = 5 v 89 90 92 91.5 93.5 db f in = 20 khz, v ref = 5 v, ?60 db input 32 33.5 db f in = 20 khz, v ref = 2.5 v 86 85.5 87.5 87 88.5 db intermodulation distortion 4 ?110 ?115 db 1 lsb means least significant bit. with the 5 v input range, 1 lsb is 76.3 v. 2 see terminology section. these specificat ions do include full temperature range variation but do not include the error contrib ution from the external reference. 3 all specifications in db are referred to a full-scale input fs. tested with an input signal at 0.5 db below full-scale, unless otherwise specified. 4 f in1 = 21.4 khz, f in2 = 18.9 khz, each tone at ?7 db below full scale.
ad7685 rev. c | page 4 of 28 vdd = 2.3 v to 5.5 v, vio = 2.3 v to vdd, v ref = vdd, t a = C40c to +85c, unless otherwise noted. table 3. parameter conditions min typ max unit reference voltage range 0.5 vdd + 0.3 v load current 250 ksps, ref = 5 v 50 a sampling dynamics ?3 db input bandwidth 2 mhz aperture delay vdd = 5 v 2.5 ns digital inputs logic levels v il C0.3 0.3 vio v v ih 0.7 vio vio + 0.3 v i il ?1 +1 a i ih ?1 +1 a digital outputs data format serial 16 bits straight binary pipeline delay conversion results available immediately after completed conversion v ol i sink = +500 a 0.4 v v oh i source = ?500 a vio ? 0.3 v power supplies vdd specified performance 2.3 5.5 v vio specified performance 2.3 vdd + 0.3 v vio range 1.8 vdd + 0.3 v standby current 1 , 2 vdd and vio = 5 v, 25c 1 50 na power dissipation vdd = 2.5 v, 100 sps throughput 1.4 w vdd = 2.5 v, 100 ksps throughput 1.35 2.4 mw vdd = 2.5 v, 200 ksps throughput 2.7 4.8 mw vdd = 5 v, 100 ksps throughput 4 6 mw vdd = 5 v, 250 ksps throughput 10 15 mw temperature range 3 specified performance t min to t max ?40 +85 c 1 with all digital inputs forced to vio or gnd as required. 2 during acquisition phase. 3 contact sales for extended temperature range.
ad7685 rev. c | page 5 of 28 timing specifications ?40c to +85c, vio = 2.3 v to 5.5 v or vdd + 0.3 v, whichever is the lowest, unless otherwise stated. table 4. vdd = 4.5 v to 5.5 v 1 parameter symbol min typ max unit conversion time: cnv rising edge to data available t conv 0.5 2.2 s acquisition time t acq 1.8 s time between conversions t cyc 4 s cnv pulse width ( cs mode) t cnvh 10 ns sck period ( cs mode) t sck 15 ns sck period (chain mode) t sck vio above 4.5 v 17 ns vio above 3 v 18 ns vio above 2.7 v 19 ns vio above 2.3 v 20 ns sck low time t sckl 7 ns sck high time t sckh 7 ns sck falling edge to data remains valid t hsdo 5 ns sck falling edge to data valid delay t dsdo vio above 4.5 v 14 ns vio above 3 v 15 ns vio above 2.7 v 16 ns vio above 2.3 v 17 ns cnv or sdi low to sdo d15 msb valid ( cs mode) t en vio above 4.5 v 15 ns vio above 2.7 v 18 ns vio above 2.3 v 22 ns cnv or sdi high or last sck falling edge to sdo high impedance ( cs mode) t dis 25 ns sdi valid setup time from cnv rising edge ( cs mode) t ssdicnv 15 ns sdi valid hold time from cnv rising edge ( cs mode) t hsdicnv 0 ns sck valid setup time from cnv rising edge (chain mode) t ssckcnv 5 ns sck valid hold time from cnv rising edge (chain mode) t hsckcnv 5 ns sdi valid setup time from sck falling edge (chain mode) t ssdisck 3 ns sdi valid hold time from sck falling edge (chain mode) t hsdisck 4 ns sdi high to sdo high (chain mode with busy indicator) t dsdosdi vio above 4.5 v 15 ns vio above 2.3 v 26 ns 1 see figure 3 and figure 4 for load conditions.
ad7685 rev. c | page 6 of 28 ?40c to +85c, vio = 2.3 v to 4.5 v or vdd + 0.3 v, whichever is the lowest, unless otherwise stated. table 5. vdd = 2.3v to 4.5 v 1 parameter symbol min typ max unit conversion time: cnv rising edge to data available t conv 0.7 3.2 s acquisition time t acq 1.8 s time between conversions t cyc 5 s cnv pulse width ( cs mode) t cnvh 10 ns sck period ( cs mode) t sck 25 ns sck period (chain mode) t sck vio above 3 v 29 ns vio above 2.7 v 35 ns vio above 2.3 v 40 ns sck low time t sckl 12 ns sck high time t sckh 12 ns sck falling edge to data remains valid t hsdo 5 ns sck falling edge to data valid delay t dsdo vio above 3 v 24 ns vio above 2.7 v 30 ns vio above 2.3 v 35 ns cnv or sdi low to sdo d15 msb valid ( cs mode) t en vio above 2.7 v 18 ns vio above 2.3 v 22 ns cnv or sdi high or last sck falling edge to sdo high impedance ( cs mode) t dis 25 ns sdi valid setup time from cnv rising edge ( cs mode) t ssdicnv 30 ns sdi valid hold time from cnv rising edge ( cs mode) t hsdicnv 0 ns sck valid setup time from cnv rising edge (chain mode) t ssckcnv 5 ns sck valid hold time from cnv rising edge (chain mode) t hsckcnv 8 ns sdi valid setup time from sck falling edge (chain mode) t ssdisck 5 ns sdi valid hold time from sck falling edge (chain mode) t hsdisck 4 ns sdi high to sdo high (chain mode with busy indicator) t dsdosdi 36 ns 1 see figure 3 and figure 4 for load conditions. 500a i ol 500a i oh 1.4v to sdo c l 50pf 02968-002 figure 3. load circuit fo r digital interface timing 30% vio 70% vio 2v or vio ? 0.5v 1 0.8v or 0.5v 2 0.8v or 0.5v 2 2v or vio ? 0.5v 1 t delay t delay 02968-003 notes 1. 2v if vio above 2.5v, vio ? 0.5v if vio below 2.5v. 2. 0.8v if vio above 2.5v, 0.5v if vio below 2.5v. figure 4. voltage levels for timing
ad7685 rev. c | page 7 of 28 absolute maximum ratings table 6. parameter rating analog inputs in+ 1 , in? 1 , ref gnd ? 0.3 v to vdd + 0.3 v or 130 ma supply voltages vdd, vio to gnd ?0.3 v to +7 v vdd to vio 7 v digital inputs to gnd ?0.3 v to vio + 0.3 v digital outputs to gnd ?0.3 v to vio + 0.3 v storage temperature range ?65c to +150c junction temperature 150c ja thermal impedance 200c/w (msop-10) jc thermal impedance 44c/w (msop-10) lead temperature vapor phase (60 sec) 215c infrared (15 sec) 220c 1 see the analog inputs section. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. esd caution
ad7685 rev. c | page 8 of 28 pin configuration and fu nction descriptions ref 1 vdd 2 in+ 3 in? 4 gnd 5 vio 10 sdi 9 sck 8 sdo 7 cnv 6 ad7685 top view (not to scale) 02968-004 figure 5. 10-lead ms op pin configuration 1 ref 2 vdd 3 in+ 4 in? 5 gnd 10 vio 9sdi 8sck 7sdo 6cnv top view (not to scale) ad7685 02968-005 notes 1. exposed pad connected to gnd. this connection is not required to mee t the electrical performances. figure 6. 10-lead qfn (l fcsp) pin configuration table 7. pin function descriptions pin no mnemonic type 1 description 1 ref ai reference input voltage. the ref range is from 0.5 v to vdd. it is referred to the gnd pin. this pin should be decoupled closely to the pin with a 10 f capacitor. 2 vdd p power supply. 3 in+ ai analog input. it is referred to in?. the voltage range, that is, the difference between in+ and in?, is 0 v to v ref . 4 in? ai analog input ground sense. connect to the analog ground plane or to a remote sense ground. 5 gnd p power supply ground. 6 cnv di convert input. this input has multiple functions. on its leading edge, it initiates the conversions and selects the interface mode of the part, chain, or cs mode. in cs mode, it enables the sdo pin when low. in chain mode, the data should be read when cnv is high. 7 sdo do serial data output. the conversion result is output on this pin. it is synchronized to sck. 8 sck di serial data clock input. when the part is select ed, the conversion result is shifted out by this clock. 9 sdi di serial data input. this input provides multiple fe atures. it selects the interface mode of the adc as follows: chain mode is selected if sdi is low during the cnv risi ng edge. in this mode, sdi is used as a data input to daisy chain the conversion results of two or more adcs onto a single sdo line. the digital data level on sdi is output on sdo with a delay of 16 sck cycles. cs mode is selected if sdi is high during the cnv risi ng edge. in this mode, either sdi or cnv can enable the serial output signals when low, and if sdi or cnv is low when the conversion is complete, the busy indicator feature is enabled. 10 vio p input/output interface digital power. nominally at the same supply as the host interface (1.8 v, 2.5 v, 3 v, or 5 v). epad exposed pad. exposed pad connected to gnd. this co nnection is not required to meet the electrical performances. 1 ai = analog input, di = digital input, do = digital output, and p = power.
ad7685 rev. c | page 9 of 28 terminology integral nonlinearity error (inl) inl refers to the deviation of each individual code from a line drawn from negative full scale through positive full scale. the point used as negative full scale occurs ? lsb before the first code transition. positive full scale is defined as a level 1? lsb beyond the last code transition. the deviation is measured from the middle of each code to the true straight line (see figure 26 ). differential nonlinearity error (dnl) in an ideal adc, code transitions are 1 lsb apart. dnl is the maximum deviation from this ideal value. it is often specified in terms of resolution for which no missing codes are guaranteed. offset error the first transition should occur at a level ? lsb above analog ground (38.1 v for the 0 v to 5 v range). the offset error is the deviation of the actual transition from that point. gain error the last transition (from 111 . . . 10 to 111 . . . 11) should occur for an analog voltage 1? lsb below the nominal full scale (4.999886 v for the 0 v to 5 v range). the gain error is the deviation of the actual level of the last transition from the ideal level after the offset is adjusted out. spurious-free dynamic range (sfdr) the difference, in decibels (db), between the rms amplitude of the input signal and the peak spurious signal. effective number of bits (enob) enob is a measurement of the resolution with a sine wave input. it is related to sinad by enob = ( sinad db ? 1.76)/6.02 and is expressed in bits. total harmonic distortion (thd) thd is the ratio of the rms sum of the first five harmonic components to the rms value of a full-scale input signal and is expressed in db. signal-to-noise ratio (snr) snr is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the nyquist frequency, excluding harmonics and dc. the value for snr is expressed in db. signal-to-(noise + distortion), sinad sinad is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the nyquist frequency, including harmonics but excluding dc. the value for sinad is expressed in db. aperture delay aperture delay is a measure of the acquisition performance and is the time between the rising edge of the cnv input and when the input signal is held for a conversion. transient resp onse the time required for the adc to accurately acquire its input after a full-scale step function is applied.
ad7685 rev. c | page 10 of 28 typical performance characteristics 02968-047 code 65536 0 16384 32768 49152 inl (lsb) 2.0 1.5 1.0 0.5 0 ?0.5 ?1.0 ?1.5 ?2.0 positive inl = +0.33lsb negative inl = ?0.50lsb figure 7. integral nonlinearity vs. code 02968-006 code in hex 80ea 80eb 80ec 80ed 80e5 80e6 80e7 80e8 80e9 counts 250000 200000 150000 100000 50000 0 0012 00 204292 27755 29041 20 vdd = ref = 5v figure 8. histogram of a dc input at the code center 02968-007 frequency (khz) 120 0 20406080100 amplitude (db of full scale) 0 ?20 ?40 ?60 ?80 ?100 ?120 ?160 ?140 ?180 8192 point fft vdd = ref = 5v f s = 250ksps f in = 20.45khz snr = 93.3db thd = ?111.6db sfdr = ?113.7db second harmonic = ?113.7db third harmonic = ?117.6db figure 9. fft plot 02968-008 code 65536 0 16384 32768 49152 dnl (lsb) 2.0 1.5 1.0 0.5 0 ?0.5 ?1.0 ?1.5 ?2.0 positive dnl = +0.21lsb negative dnl = ?0.30lsb figure 10. differential nonlinearity vs. code 02968-009 code in hex 8058 804e 804f 8050 8051 8052 8053 8054 8055 8056 8057 counts 140000 120000 100000 80000 60000 40000 20000 0 02 213 6956 179 0 0 60966 125055 8667 59082 vdd = ref = 2.5v figure 11. histogram of a dc input at the code center 02968-010 frequency (khz) 120 0 20406080100 amplitude (db of full scale) 0 ?20 ?40 ?60 ?80 ?100 ?120 ?140 ?160 ?180 16384 point fft vdd = ref = 2.5v f s = 250ksps f in = 20.45khz snr = 88.8db thd = ?103.5db sfdr = ?104.5db second harmonic = ?112.4db third harmonic = ?105.4db figure 12. fft plot
ad7685 rev. c | page 11 of 28 02968-011 reference voltage (v) 5.5 2.3 2.7 3.1 3.5 3.9 4.3 4.7 5.1 enob (bits) 13 17 16 15 14 sinad (db) 100 95 90 85 80 snr sinad enob figure 13. snr, sinad, and enob vs. reference voltage 02968-012 sinad (db) frequency (khz) 200 0 50 100 150 100 95 90 85 80 75 70 v ref = 5v, ?1db v ref = 2.5v, ?1db v ref = 5v, ?10db figure 14. sinad vs. frequency 02968-013 temperature (c) 125 ?55 ?35 ?15 5 25 45 65 85 105 snr (db) 100 95 90 85 80 75 70 v ref = 5v v ref = 2.5v figure 15. snr vs. temperature 02968-014 reference voltage (v) 5.5 2.3 2.7 3.1 3.5 3.9 4.3 4.7 5.1 thd, sfdr (db) ? 90 ?95 ?100 ?105 ?110 ?115 ?120 ?125 ?130 sfdr thd figure 16. thd, sfdr vs. reference voltage 02968-015 frequency (khz) 200 0 50 100 150 thd (db) ? 60 ?70 ?80 ?90 ?100 ?110 ?120 v ref = 2.5v, ?1db v ref = 5v, ?1db v ref = 5v, ?10db figure 17. thd vs. frequency 02968-016 temperature (c) 125 ?55 ?35 ?15 5 25 45 65 85 105 thd (db) ? 90 ?100 ?110 ?120 ?130 v ref = 2.5v v ref = 5v figure 18. thd vs. temperature
ad7685 rev. c | page 12 of 28 02968-017 input level (db) 0 ?10 ?8 ?6 ?4 ?2 thd (db) ?120 ? 105 ?110 ?115 snr reference to full scale (db) 95 94 93 92 91 90 snr thd 02968-020 temperature (c) 125 ?55 ?35 ?15 5 25 45 65 85 105 oper a ting currents (a) 1000 750 500 250 0 vdd = 5v vio f s = 100ksps vdd = 2.5v figure 19. snr and thd vs. input level figure 22. operating currents vs. temperature 02968-021 temperature (c) 125 ?55 ?35 ?15 5 25 45 65 85 105 offset, gain error (lsb) 6 4 5 2 3 0 1 ?2 ?1 ?4 ?3 ?6 ?5 gain error offset error 02968-018 supply (v) 5.5 2.3 2.7 3.1 3.5 3.9 4.3 4.7 5.1 oper a ting currents (a) 1000 750 500 250 0 vdd vio f s = 100ksps figure 23. offset and gain error vs. temperature figure 20. operating currents vs. supply 02968-022 sdo capacitive load (pf) 120 020406080100 t dsdo delay (ns) 25 20 15 10 5 0 vdd = 2.5v, 85c vdd = 3.3v, 25c vdd = 3.3v, 85c vdd = 5v, 85c vdd = 5v, 25c vdd = 2.5v, 25c 02968-019 temperature (c) 125 ?55 ?35 ?15 5 25 45 65 85 105 power-down currents (na) 1000 750 500 250 0 vdd + vio figure 24. t dsdo delay vs. capacitance load and supply figure 21. power-down currents vs. temperature
ad7685 rev. c | page 13 of 28 theory of operation sw+ msb 16,384c in+ lsb comp control logic switches control busy output code cnv ref gnd in? 4c 2c c c 32,768c sw? msb 16,384c lsb 4c 2c c c 32,768c 02968-023 figure 25. adc simplified schematic circuit information the ad7685 is a fast, low power, single-supply, precise 16-bit adc using a successive approximation architecture. the ad7685 is capable of converting 250,000 samples per second (250 ksps) and powers down between conversions. when operating at 100 sps, for example, it consumes typically 1.35 w with a 2.5 v supply, ideal for battery-powered applications. the ad7685 provides the user with on-chip, track-and-hold and does not exhibit any pipeline delay or latency, making it ideal for multiple multiplexed channel applications. the ad7685 is specified from 2.3 v to 5.5 v and can be interfaced to any 1.8 v to 5 v digital logic family. it is housed in a 10-lead msop or a tiny 10-le ad qfn (lfcsp) that combines space savings and allows flexible configurations. it is pin-for-pin-compatible with the ad7686, ad7687 , and ad7688. converter operation the ad7685 is a successive approximation adc based on a charge redistribution dac. figure 25 shows the simplified schematic of the adc. the capacitive dac consists of two identical arrays of 16 binary weighted capacitors, which are connected to the two comparator inputs. during the acquisition phase, terminals of the array tied to the comparators input are connected to gnd via sw+ and sw?. all independent switches are connected to the analog inputs. therefore, the capacitor arrays are used as sampling capacitors and acquire the analog signal on the in+ and in? inputs. when the acquisition phase is complete and the cnv input goes high, a conversion phase is initiated. when the conversion phase begins, sw+ and sw? are open ed first. the two capacitor arrays are then disconnected from the inputs and connected to the gnd input. therefore, the differential voltage between the inputs in+ and in? captured at the end of the acquisition phase is applied to the comparator inputs, causing the comparator to become unbalanced. by switching each element of the capacitor array between gnd and ref, the comparator input varies by binary weighted voltage steps (v ref /2, v ref /4 . . . v ref /65536). the control logic toggles these switches, starting with the msb, to bring the comparator back into a balanced condition. after the completion of this process, the part powers down and returns to the acquisition phase, and the control logic generates the adc output code and a busy signal indicator. because the ad7685 has an on-board conversion clock, the serial clock, sck, is not required for the conversion process.
ad7685 rev. c | page 14 of 28 transfer functions the ideal transfer characteristic for the ad7685 is shown in figure 26 and table 8 . 000...000 000...001 000...010 111...101 111...110 111...111 adc code (straight bin a r y) analog input +fs ? 1.5 lsb +fs ? 1 lsb ?fs + 1 lsb ?fs ?fs + 0.5 lsb 02968-024 figure 26. adc ideal transfer function typical connection diagram figure 27 shows an example of the recommended connection diagram for the ad7685 when multiple supplies are available. ad7685 ref gnd vdd in? in+ vio sdi sck sdo cnv 3- or 4-wire interface 5 100nf 100nf 5v 10f 2 7v 7v ?2v 1.8v to vdd ref 1 0 to vref 33 ? 2.7nf 3 4 02968-025 notes 1. see voltage reference input section for reference selection. 2. c ref is usually a 10f ceramic capacitor (x5r). 3. see driver amplifier choice section. 4. optional filter. see analog input section. 5. see digital interface for most convenient interface mode. figure 27. typical application diagram with multiple supplies table 8. output codes and ideal input voltages description analog input v ref = 5 v digital output code hexa fsr C 1 lsb 4.999924 v ffff 1 midscale + 1 lsb 2.500076 v 8001 midscale 2.5 v 8000 midscale C 1 lsb 2.499924 v 7fff Cfsr + 1 lsb 76.3 v 0001 Cfsr 0 v 0000 2 1 this is also the code for an overranged analog input (v in+ ? v in? above v ref ? v gnd ). 2 this is also the code for an underranged analog input (v in+ ? v in? below v gnd ).
ad7685 rev. c | page 15 of 28 analog inputs figure 28 shows an equivalent circuit of the input structure of the ad7685. the two diodes, d1 and d2, provide esd protection for the analog inputs in+ and in?. care must be taken to ensure that the analog input signal never exceeds the supply rails by more than 0.3 v because this will cause these diodes to begin to forward-bias and start conducting current. these diodes can handle a forward-biased current of 130 ma maximum. for instance, these conditions could eventually occur when the input buffers (u1) supplies are different from vdd. in such a case, an input buffer with a short-circuit current limitation can be used to protect the part. c in r in d1 d2 c pin in+ or in? gnd v dd 02968-026 figure 28. equivalent analog input circuit this analog input structure allows the sampling of the differential signal between in+ and in?. by using this differential input, small signals common to both inputs are rejected, as shown in figure 29 , which represents the typical cmrr over frequency. for instance, by using in? to sense a remote signal ground, ground potential differences between the sensor and the local adc ground are eliminated. 02968-027 frequency (khz) 10000 1 10 100 1000 cmrr (db) 80 70 60 50 40 v dd = 5v v dd = 2.5v figure 29. analog input cmrr vs. frequency during the acquisition phase, the impedance of the analog inputs (in+ or in?) can be modeled as a parallel combination of capacitor c pin and the network formed by the series connection of r in and c in . c pin is primarily the pin capacitance. r in is typically 3 k and is a lumped component made up of some serial resistors and the on resistance of the switches. c in is typically 30 pf and is mainly the adc sampling capacitor. during the conversion phase, where the switches are opened, the input impedance is limited to c pin . r in and c in make a 1-pole, low-pass filter that reduces undesirable aliasing effects and limits the noise. when the source impedance of the driving circuit is low, the ad7685 can be driven directly. large source impedances significantly affect the ac performance, especially thd. the dc performances are less sensitive to the input impedance. the maximum source impedance depends on the amount of thd that can be tolerated. the thd degrades as a function of the source impedance and the maximum input frequency, as shown in figure 30 . 02968-028 frequency (khz) 100 0 2 55 07 5 thd (db) ? 60 ?70 ?80 ?90 ?100 ?110 ?120 r s = 33 ? r s = 50 ? r s = 100 ? r s = 250 ? f igure 30. thd vs. analog input frequency and source resistance
ad7685 rev. c | page 16 of 28 driver amplifier choice although the ad7685 is easy to drive, the driver amplifier needs to meet the following requirements: ? the noise generated by the driver amplifier needs to be kept as low as possible to preserve the snr and transition noise performance of the ad7685. note that the ad7685 has a noise much lower than most of the other 16-bit adcs and, therefore, can be driven by a noisier amplifier to meet a given system noise specification. the noise coming from the amplifier is filtered by the ad7685 analog input circuit low- pass filter made by r in and c in or by an external filter, if one is used. because the typical noise of the ad7685 is 35 v rms, the snr degradation due to the amplifier is ? ? ? ? ? ? ? ? ? ? ? ? + = ? 2 3db 2 )(f 2 35 35 20log n loss ne snr where: f C3db is the input bandwidth in mhz of the ad7685 (2 mhz) or the cutoff frequency of the input filter, if one is used. n is the noise gain of the amplifier (for example, 1 in buffer configuration). e n is the equivalent input noise voltage of the op amp, in nv/hz. ? for ac applications, the driver should have a thd performance commensurate with the ad7685. figure 17 shows the ad7685s thd vs. frequency. ? for multichannel, multiplexed applications, the driver amplifier and the ad7685 analog input circuit must settle a full-scale step onto the capacitor array at a 16-bit level (0.0015%). in the amplifiers data sheet, settling at 0.1% to 0.01% is more commonly specified. this could differ significantly from the settling time at a 16-bit level and should be verified prior to driver selection. table 9. recommended driver amplifiers amplifier typical application ada4841-x very low noise and low power ad8605 , ad8615 5 v single-supply, low power ad8655 5 v single-supply, low power op184 low power, low noise, and low frequency ad8021 very low noise and high frequency ad8022 very low noise and high frequency ad8519 small, low power and low frequency AD8031 high frequency and low power voltage reference input the ad7685 voltage reference input, ref, has a dynamic input impedance and should therefore be driven by a low impedance source with efficient decoupling between the ref and gnd pins, as explained in the layout section. when ref is driven by a very low impedance source, for example, a reference buffer using the AD8031 or the ad8605, a 10 f (x5r, 0805 size) ceramic chip capacitor is appropriate for optimum performance. if an unbuffered reference voltage is used, the decoupling value depends on the reference used. for instance, a 22 f (x5r, 1206 size) ceramic chip capacitor is appropriate for optimum performance using a low temperature drift adr43x reference. if desired, smaller reference decoupling capacitor values down to 2.2 f can be used with a minimal impact on performance, especially dnl. power supply the ad7685 is specified over a wide operating range from 2.3 v to 5.5 v. it has, unlike other low voltage converters, a noise low enough to design a 16-bit resolution system with low supply and respectable performance. it uses two power supply pins: a core supply vdd and a digital input/output interface supply vio. vio allows direct interface with any logic between 1.8 v and vdd. to reduce the number of supplies needed, the vio and vdd can be tied together. the ad7685 is independent of power supply sequencing between vio and vdd. additionally, it is very insensitive to power supply variations over a wide frequency range, as shown in figure 31 , which represents psrr over frequency. 02968-029 frequency (khz) 10000 1 10 100 1000 psrr (db) 110 80 90 100 70 60 50 40 30 vdd = 5v vdd = 2.5v figure 31. psrr vs. frequency
ad7685 rev. c | page 17 of 28 the ad7685 powers down automatically at the end of each conversion phase and, therefore, the power scales linearly with the sampling rate, as shown in figure 32 . this makes the part ideal for low sampling rate (even a few hz) and low battery- powered applications. 02968-030 sampling rate (sps) 1000000 10 100 1000 10000 100000 oper a ting currents (a) 1000 10 0.1 0.001 10000 100 1 0.01 vdd = 5v vio vdd = 2.5v f igure 32. operating currents vs. sampling rate s upplying the adc from the reference for simplified applications, the ad7685, with its low operating current, can be supplied directly using the reference circuit, as shown in figure 33 . the reference line can be driven by either: ? the system power supply directly. ? a reference voltage with enough current output capability, such as the adr43x. ? a reference buffer, such as the AD8031 , that can also filter the system power supply, as shown in figure 33 . AD8031 ad7685 vio ref vdd 10f 1f 10 ? 10k ? 5v 5v 5v 1f 1 02968-031 1 optional reference buffer and filter. figure 33. example of application circuit digital interface though the ad7685 has a reduced number of pins, it offers substantial flexibility in its serial interface modes. the ad7685, when in cs mode, is compatible with spi, qspi, digital hosts, and dsps, for example, blackfin? adsp-bf53x or adsp-219x. this interface can use either 3-wire or 4-wire. a 3-wire interface using the cnv, sck, and sdo signals minimizes wiring connections, useful, for instance, in isolated applications. a 4-wire interface using the sdi, cnv, sck, and sdo signals allows cnv, which initiates the conversions, to be independent of the readback timing (sdi). this is useful in low jitter sampling or simultaneous sampling applications. the ad7685, when in chain mode, provides a daisy-chain feature using the sdi input for cascading multiple adcs on a single data line similar to a shift register. the mode in which the part operates depends on the sdi level when the cnv rising edge occurs. the cs mode is selected if sdi is high and the chain mode is selected if sdi is low. the sdi hold time is such that when sdi and cnv are connected together, the chain mode is always selected. in either the cs mode or the chain mode, the ad7685 offers the flexibility to optionally force a start bit in front of the data bits. this start bit can be used as a busy signal indicator to interrupt the digital host and trigger the data reading. otherwise, without a busy indicator, the user must time out the maximum conversion time prior to readback. the busy indicator feature is enabled as follows: ? in the cs mode, if cnv or sdi is low when the adc conversion ends (see and ). figure 37 figure 41 ? in the chain mode, if sck is high during the cnv rising edge (see figure 45 ).
ad7685 rev. c | page 18 of 28 cs mode 3-wire, no busy indicator this mode is usually used when a single ad7685 is connected to an spi-compatible digital host. the connection diagram is shown in figure 34 , and the corresponding timing is given in figure 35 . with sdi tied to vio, a rising edge on cnv initiates a conversion, selects the cs mode, and forces sdo to high impedance. once a conversion is initiated, it will continue to completion irrespective of the state of cnv. for instance, it could be useful to bring cnv low to select other spi devices, such as analog multiplexers, but cnv must be returned high before the minimum conversion time and held high until the maximum conversion time to avoid the generation of the busy signal indicator. when conversion is completed, the ad7685 enters the acquisition phase and powers down. when cnv goes low, the msb is output onto sdo. the remaining data bits are then clocked by subsequent sck falling edges. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge will allow a faster reading rate provided it has an acceptable hold time. after the 16th sck falling edge or when cnv goes high, whichever is earlier, sdo returns to high impedance. cnv sck sdo sdi data in clk convert v io digital host ad7685 02968-032 figure 34. cs mode 3-wire, no busy indicator connection diagram (sdi high) sdo d15 d14 d13 d1 d0 t dis sck 1 2 3 14 15 16 t sck t sckl t sckh t hsdo t dsdo cnv conversion acquisition t conv t cyc acquisition sdi = 1 t cnvh t acq t en 02968-033 figure 35. cs mode 3-wire, no busy indicator serial interface timing (sdi high)
ad7685 rev. c | page 19 of 28 cs mode 3-wire with busy indicator this mode is usually used when a single ad7685 is connected to an spi-compatible digital host having an interrupt input. the connection diagram is shown in figure 36 , and the corresponding timing is given in figure 37 . with sdi tied to vio, a rising edge on cnv initiates a conversion, selects the cs mode, and forces sdo to high impedance. sdo is maintained in high impedance until the completion of the conversion irrespective of the state of cnv. prior to the minimum conversion time, cnv could be used to select other spi devices, such as analog multiplexers, but cnv must be returned low before the minimum conversion time and held low until the maximum conversion time to guarantee the generation of the busy signal indicator. when the conversion is complete, sdo goes from high impedance to low. with a pull-up on the sdo line, this transition can be used as an interrupt signal to initiate the data reading controlled by the digital host. the ad7685 then enters the acquisition phase and powers down. the data bits are then clocked out, msb first, by subsequent sck falling edges. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge will allow a faster reading rate provided it has an acceptable hold time. after the optional 17th sck falling edge, or when cnv goes high, whichever is earlier, sdo returns to high impedance. data in irq clk convert vio digital host 02968-034 47k ? cnv sck sdo sdi v io ad7685 figure 36. cs mode 3-wire with busy indicator connection diagram (sdi high) sdo d15 d14 d1 d0 t dis sck 1 2 3 15 16 17 t sck t sckl t sckh t hsdo t dsdo cnv conversion acquisition t conv t cyc t cnvh t acq acquisition sdi = 1 0 2968-035 figure 37. cs mode 3-wire with busy indicator serial interface timing (sdi high)
ad7685 rev. c | page 20 of 28 cs mode 4-wire, no busy indicator this mode is usually used when multiple ad7685s are connected to an spi-compatible digital host. a connection diagram example using two ad7685s is shown in figure 38 , and the corresponding timing is given in figure 39 . with sdi high, a rising edge on cnv initiates a conversion, selects the cs mode, and forces sdo to high impedance. in this mode, cnv must be held high during the conversion phase and the subsequent data readback (if sdi and cnv are low, sdo is driven low). prior to the minimum conversion time, sdi could be used to select other spi devices, such as analog multiplexers, but sdi must be returned high before the minimum conversion time and held high until the maximum conversion time to avoid the generation of the busy signal indicator. when the conversion is complete, the ad7685 enters the acquisition phase and powers down. each adc result can be read by bringing low its sdi input, which consequently outputs the msb onto sdo. the remaining data bits are then clocked by subsequent sck falling edges. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge will allow a faster reading rate, provided it has an acceptable hold time. after the 16th sck falling edge, or when sdi goes high, whichever is earlier, sdo returns to high impedance and another ad7685 can be read. if multiple ad7685s are selected at the same time, the sdo output pin handles this contention without damage or induced latch-up. meanwhile, it is recommended to keep this contention as short as possible to limit extra power dissipation. data in clk cs1 convert cs2 digital host 02968-036 cnv sck sdo sdi ad7685 cnv sck sdo sdi ad7685 figure 38. cs mode 4-wire, no busy in dicator connection diagram sdo d15 d14 d13 d1 d0 t dis sck 123 303132 t hsdo t dsdo t en conversion acquisition t conv t cyc t acq acquisition sdi(cs1) cnv t ssdicnv t hsdicnv d1 14 15 t sck t sckl t sckh d0 d15 d14 17 18 16 sdi(cs2) 02968-037 figure 39. cs mode 4-wire, no busy indicator serial interface timing
ad7685 rev. c | page 21 of 28 cs mode 4-wire with busy indicator this mode is usually used when a single ad7685 is connected to an spi-compatible digital host, which has an interrupt input, and it is desired to keep cnv, which is used to sample the analog input, independent of the signal used to select the data reading. this requirement is particularly important in applications where low jitter on cnv is desired. the connection diagram is shown in figure 40 , and the corresponding timing is given in figure 41 . with sdi high, a rising edge on cnv initiates a conversion, selects the cs mode, and forces sdo to high impedance. in this mode, cnv must be held high during the conversion phase and the subsequent data readback (if sdi and cnv are low, sdo is driven low). prior to the minimum conversion time, sdi could be used to select other spi devices, such as analog multiplexers, but sdi must be returned low before the minimum conversion time and held low until the maximum conversion time to guarantee the generation of the busy signal indicator. when the conversion is complete, sdo goes from high impedance to low. with a pull-up on the sdo line, this transition can be used as an interrupt signal to initiate the data readback controlled by the digital host. the ad7685 then enters the acquisition phase and powers down. the data bits are then clocked out, msb first, by subsequent sck falling edges. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge will allow a faster reading rate provided it has an acceptable hold time. after the optional 17th sck falling edge, or sdi going high, whichever is earlier, the sdo returns to high impedance. data in irq clk convert cs1 vio digital host 02968-038 47k ? cnv sck sdo sdi ad7685 figure 40. cs mode 4-wire with busy indicator connection diagram sdo d15 d14 d1 d0 t dis sck 1 2 3 151617 t sck t sckl t sckh t hsdo t dsdo t en conversion acquisition t conv t cyc t acq acquisition sdi cnv t ssdicnv t hsdicnv 02968-039 figure 41. cs mode 4-wire with busy indicator serial interface timing
ad7685 rev. c | page 22 of 28 chain mode, no busy indicator this mode can be used to daisy-chain multiple ad7685s on a 3-wire serial interface. this feature is useful for reducing component count and wiring connections, for example, in isolated multiconverter applications or for systems with a limited interfacing capacity. data readback is analogous to clocking a shift register. a connection diagram example using two ad7685s is shown in figure 42 , and the corresponding timing is given in figure 43 . when sdi and cnv are low, sdo is driven low. with sck low, a rising edge on cnv initiates a conversion and selects the chain mode. in this mode, cnv is held high during the conversion phase and the subsequent data readback. when the conversion is complete, the msb is output onto sdo and the ad7685 enters the acquisition phase and powers down. the remaining data bits stored in the internal shift register are then clocked by subsequent sck falling edges. for each adc, sdi feeds the input of the internal shift register and is clocked by the sck falling edge. each adc in the chain outputs its data msb first, and 16 n clocks are required to readback the n adcs. the data is valid on both sck edges. although the rising edge can be used to capture the data, a digital host using the sck falling edge will allow a faster reading rate and, consequently, more ad7685s in the chain, provided the digital host has an acceptable hold time. the maximum conversion rate may be reduced due to the total readback time. for instance, with a 5 ns digital host setup time and 3 v interface, up to eight ad7685s running at a conversion rate of 220 ksps can be daisy-chained on a 3-wire port. clk convert data in digital host 02968-040 cnv sck sdo sdi ad7685 b cnv sck sdo sdi ad7685 a figure 42. chain mode connection diagram sdo a = sdi b d a 15 d a 14 d a 13 sck 1 2 3 303132 t ssdisck t hsdisck t en conversion acquisition t conv t cyc t acq acquisition cnv d a 1 14 15 t sck t sckl t sckh d a 0 17 18 16 sdi a = 0 sdo b d b 15 d b 14 d b 13 d a 1 d b 1d b 0d a 15 d a 14 t hsdo t dsdo t ssckcnv t hsckcnv d a 0 02968-041 figure 43. chain mode serial interface timing
ad7685 rev. c | page 23 of 28 chain mode with busy indicator this mode can also be used to daisy chain multiple ad7685s on a 3-wire serial interface while providing a busy indicator. this feature is useful for reducing component count and wiring connections, for example, in isolated multiconverter applications or for systems with a limited interfacing capacity. data readback is analogous to clocking a shift register. a connection diagram example using three ad7685s is shown in figure 44 , and the corresponding timing is given in figure 45 . when sdi and cnv are low, sdo is driven low. with sck high, a rising edge on cnv initiates a conversion, selects the chain mode, and enables the busy indicator feature. in this mode, cnv is held high during the conversion phase and the subsequent data readback. when all adcs in the chain have completed their conversions, the near-end adc (adc c in figure 44 ) sdo is driven high. this transition on sdo can be used as a busy indicator to trig ger the data readback controlled by the digital host. the ad7685 then enters the acquisition phase and powers down. the data bits stored in the internal shift register are then clocked out, msb first, by subsequent sck falling edges. for each adc, sdi feeds the input of the internal shift register and is clocked by the sck falling edge. each adc in the chain outputs its data msb first, and 16 n + 1 clocks are required to readback the n adcs. although the rising edge can be used to capture the data, a digital host also using the sck falling edge allows a faster reading rate and, consequently, more ad7685s in the chain, provided the digital host has an acceptable hold time. for instance, with a 5 ns digital host setup time and 3 v interface, up to eight ad7685s running at a conversion rate of 220 ksps can be daisy-chained to a single 3-wire port. clk convert data in irq digital host 02968-042 cnv sck sdo sdi ad7685 c cnv sck sdo sdi ad7685 a cnv sck sdo sdi ad7685 b figure 44. chain mode with bu sy indicator connection diagram sdo a = sdi b d a 15 d a 14 d a 13 sck 123 35 47 48 t en conversion acquisition t conv t cyc t acq acquisition cnv = sdi a d a 1 415 t sck t sckh t sckl d a 0 17 34 16 sdo b = sdi c d b 15 d b 14 d b 13 d a 1 d b 1d b 0d a 15 d a 14 49 t ssdisck t hsdisck t hsdo t dsdo sdo c d c 15 d c 14 d c 13 d a 1d a 0 d c 1d c 0d a 14 19 31 32 18 33 d b 1d b 0d a 15 d b 15 d b 14 t dsdosdi t ssckcnv t hsckcnv 0 2968-043 d a 0 t dsdosdi t dsdosdi t dsdosdi t dsdosdi figure 45. chain mode with busy indicator serial interface timing
ad7685 rev. c | page 24 of 28 application hints layout the printed circuit board (pcb) that houses the ad7685 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. the pinout of the ad7685 with all its analog signals on the left side and all its digital signals on the right side eases this task. avoid running digital lines under the device because these couple noise onto the die, unless a ground plane under the ad7685 is used as a shield. fast switching signals, such as cnv or clocks, should never run near analog signal paths. crossover of digital and analog signals should be avoided at least one ground plane should be used. it could be common or split between the digital and analog section. in the latter case, the planes should be joined underneath the ad7685. the ad7685 voltage reference input ref has a dynamic input impedance and should be decoupled with minimal parasitic inductances. this is done by placing the reference decoupling ceramic capacitor close to, and ideally right up against, the ref and gnd pins and connected with wide, low impedance traces. finally, the power supplies vdd and vio should be decoupled with ceramic capacitors, typically 100 nf, placed close to the ad7685 and connected using short and wide traces to provide low impedance paths and to reduce the effect of glitches on the power supply lines. an example layout following these rules is shown in figure 46 and figure 47 . evaluating the performance of the ad7685 other recommended layouts for the ad7690 are outlined in the documentation of the evaluation board ( eval-ad7685cb ). the evaluation board package includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from a pc via the universal evaluation control board ( eval-control brd3 ). 02968-044 figure 46. example of layout of the ad7685 (top layer) 0 2968-045 figure 47. example of layout of the ad7685 (bottom layer)
ad7685 rev. c | page 25 of 28 true 16-bit isolated application example in applications where high accuracy and isolation are required, for example, power monitoring, motor control, and some medical equipment, the circuit given in figure 48 , using the ad7685 and the adum1402c digital isolator, provides a compact and high performance solution. multiple ad7685s are daisy-chained to reduce the number of signals to isolate. note that the sckout, which is a readback of the ad7685s clock, has a very short skew with the data signal. this skew is the channel-to-channel matching propagation delay of the digital isolator (t pskcd ). this allows running the serial interface at the maximum speed of the digital isolator (45 mbps for the adum1402c), which would have been otherwise limited by the cascade of the propagation delays of the digital isolator. the complete analog chain runs on a 5 v single supply using the adr391 low dropout reference voltage and the rail-to-rail cmos ad8618 amplifier while offering true bipolar input range. in? gnd ref vdd vio sdo v dd1 , v e1 gnd 1 v dd2 , v e2 gnd 2 sck cnv sdi ad7685 1/4 ad8618 5v 1k ? 2v ref 10v input 5v ref 5 v 5v 10f 100nf 100nf in? gnd ref vdd vio sdo sck cnv sdi ad7685 1/4 ad8618 5v 1k ? 2v ref 10v input 5v ref 5v 10f 100nf in? gnd ref vdd vio sdo sck cnv sdi ad7685 1/4 ad8618 5v 1k ? 2v ref 10v input 5v ref 5v 10f 100nf in? in+ in+ in+ in+ gnd ref vdd vio sdo sck cnv sdi ad7685 1/4 ad8618 5v 1k ? 4k ? 4k ? 4k ? 4k ? 2v ref 5v 5v 1k ? 1k ? 1k ? 100nf 10f 5v ref 2v ref 4k ? 10v input 5v ref 5v 10f 100nf v ia v ib v oc v od v oa v ob v ic v id 2.7v to 5v 100nf data sckout sckin convert adum1402c out gnd in adr391 02968-046 figure 48. a true 16-bit isolated simultaneous sampling acquisition system
ad7685 rev. c | page 26 of 28 outline dimensions compliant to jedec standards mo-187-ba 091709-a 6 0 0.70 0.55 0.40 5 10 1 6 0.50 bsc 0.30 0.15 1.10 max 3.10 3.00 2.90 coplanarity 0.10 0.23 0.13 3.10 3.00 2.90 5.15 4.90 4.65 pin 1 identifier 15 max 0.95 0.85 0.75 0.15 0.05 figure 49.10-lead micro small outline package [msop] (rm-10) dimensions shown in millimeters 2.48 2.38 2.23 0.50 0.40 0.30 121009-a top view 10 1 6 5 0.30 0.25 0.20 bottom view pin 1 index area seating plane 0.80 0.75 0.70 1.74 1.64 1.49 0.20 ref 0.05 max 0.02 nom 0.50 bsc exposed pad 3.10 3.00 sq 2.90 p i n 1 i n d i c a t o r ( r 0 . 1 5 ) for proper connection of the exposed pad, refer to the pin configuration and function descriptions section of this data sheet. figure 50. 10-lead lead frame chip scale package [qfn (lfcsp_wd)] 3 mm 3 mm body, very very thin, dual lead (cp-10-9) dimensions shown in millimeters
ad7685 rev. c | page 27 of 28 ordering guide model 1 notes integral nonlinearity no missing code temperature range package description package option branding ordering quantity ad7685acpzrl 6 lsb max 15 bits C40c to +85c 10-lead qfn (lfcsp_wd) cp-10-9 c4h reel, 5,000 ad7685acpzrl7 6 lsb max 15 bits C40c to +85c 10-lead qfn (lfcsp_wd) cp-10-9 c4h reel, 1,500 ad7685armz 6 lsb max 15 bits C40c to +85c 10-lead msop rm-10 c4h tube, 50 ad7685armzrl7 6 lsb max 15 bits C40c to +85c 10-lead msop rm-10 c4h reel, 1,000 ad7685bcpzrl 3 lsb max 16 bits C40c to +85c 10-lead qfn (lfcsp_wd) cp-10-9 c3d reel, 5,000 ad7685bcpzrl7 3 lsb max 16 bits C40c to +85c 10-lead qfn (lfcsp_wd) cp-10-9 c3d reel, 1,500 ad7685brmz 3 lsb max 16 bits C40c to +85c 10-lead msop rm-10 c3d tube, 50 ad7685brmzrl7 3 lsb max 16 bits C40c to +85c 10-lead msop rm-10 c3d reel, 1,000 ad7685ccpzrl 2 lsb max 16 bits C40c to +85c 10-lead qfn (lfcsp_wd) cp-10-9 c4j reel, 5,000 ad7685ccpzrl7 2 lsb max 16 bits C40c to +85c 10-lead qfn (lfcsp_wd) cp-10-9 c4j reel, 1,500 ad7685crmz 2 lsb max 16 bits C40c to +85c 10-lead msop rm-10 c4j tube, 50 ad7685crmzrl7 2 lsb max 16 bits C40c to +85c 10-lead msop rm-10 c4j reel, 1,000 eval-ad7685cbz 2 evaluation board eval-control brd2z 3 controller board eval-control brd3z 3 controller board 1 z = rohs compliant part. 2 this board can be used as a standalone evaluation board or in conjunction with the eval-control brdx for evaluation/demonstrat ion purposes. 3 these boards allow a pc to control and communicate with all analog devices evaluation boards ending in the cb designators.
ad7685 rev. c | page 28 of 28 notes ?2004C2011 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. d02968-0-8/11(c)

▲Up To Search▲

Price & Availability of AD8031

	To Download AD8031 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .