designed & dimensioned in millimeters[inches] do not scale from this print pesc-xx-xx-xx-01-x-vt-xx power pins (per end) -01, -02, -04 (see table 1 for available combinations) signal pins -12 -40 (see table 1 for available combinations) power pins (per end) -01, -02, -04 (see table 1 for available combinations) option -lc: locking clip (use lc-11-tm) (see fig. 2, sht 2) -s: selective gold on contact /matte tin on tail -t: matte tin all over -l: light selective gold on contact/matte tin on tail plating specification vertical lead style -01 f "a" ref (see table 2) 12.00 ref .472 "b" (see table 2) 11.43 .450 (typ) ref 5.72 (typ) .225 "a" "a" c1 01 04 12.64 .497 ref 0.64 ref .025 0.50 (typ) ref .020 2.54 (typ) .100 ("e" spaces @ [2.54] .100) 2.54 ref (typ) .100 0.79 x 0.41 [.016] ref (typ) .031 2.040 .080 0.38 ref (typ) .015 4.40 ref .173 "d" (see table 2) 2 max sway (typ) (either direction) "b" "b" "c" "c" section "a"-"a" c4 c5 max c-08-02-x c11 c13 6.60 ref (typ) .260 0.64 (typ) ref .025 5.70 ref .224 (contact area) 1.54 (typ) .061 2.47 - 0.50 + 0.25 .097 - .020 + .010 (typ) 2.54 (typ) .100 1.91 .075 section "b"-"b" pes-02-v-40 sub-c-204-01-xx c6 c7 4.00 .157 section "c"-"c" c8 c fig. 1 pesc-01-40-01-01-x-vt shown * * = not released f f sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: vertical power socket by: pesc-xx-xx-xx-01-x-vt-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 1/10/2006 2 1 sheet scale: 1:0.666667 insulator: lcp, color: black contact: copper alloy f:\dwg\misc\mktg\pesc-xx-xx-xx-01-x-vt-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: 0.038[.0015] max. 3. minimum pushout force: 2.22n [.5 lb]. 4. parts to be packaged in trays. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision f
3.50 .138 (2 plcs) 2.75 .108 (measure at tips) "c" (see table 2) 2 max sway (typ) (either direction) lc-11-tm c9 3.50 ref .138 fig. 2 pesc-01-40-01-01-x-vt-lc shown (same as fig. 1, except as shown) 0.64 (typ) ref .025 2 max sway (typ) (either direction) 6.35 (typ) .250 "b" (see table 2) "a" ref (see table 2) fig. 3 pesc-02-40-02-01-x-vt shown (same as fig. 1 except as shown) c11 c10 pes-04-v-40 6.35 (typ) .250 "b" (see table 2) "a" ref (see table 2) fig. 4 pesc-04-40-04-01-x-vt shown (same as fig. 1 except as shown) c13 c12 pes-08-v-40 pes-02-v-40 "d" (see table 2) "d" (see table 2) f sheet of vertical power socket by: pesc-xx-xx-xx-01-x-vt-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 1/10/2006 2 2 sheet scale: 1:0.666667 revision f f:\dwg\misc\mktg\pesc-xx-xx-xx-01-x-vt-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|