general purpose pin photodiodes specifications responsivity: 0.32 a/w minimum, 0.36 a/w typical @ 632.8nm; 0.50 a/w minimum, 0.55 a/w typical @ 900 nm series resistance: 100 w maximum (measured by applying +10ma to photodiode and measuring voltage across anode and cathode) part number active area storage & operating temp. shunt resistance dark current 1 @ 5v breakdown voltage 2 @ 10 m a capacitance 3 (typ) nep 4 max. linear current 5 response time 6 @ 10v . in. (mm) (c ) (min) (m-ohm) (typ) (na) (max) (na) (typ) (v) at 0v (pf) at 5v (pf) (typ) (w/ ? hz) (typ) (ma) (typ) (nsec) sd 057-11-21-015 0.051 x 0.051 (1.3 x 1.3) -20 to 75 800 0.5 2.0 50 28 6 2.8x10 -14 0.17 7 sd 057-11-21-011 0.051 x 0.051 (1.3 x 1.3) -40 to 110 800 0.5 2.0 50 28 6 2.8x10 -14 0.17 7 sd 076-11-21-011 (isolated) ?211 0.105 x 0.043 (2.66 x 1.09) -40 to 110 450 0.9 3.5 50 50 10 3.2x10 -14 0.29 8 sd 100-11-21-021 (isolated) -221 0.100 (dia.) (2.54 dia.) -40 to 110 300 1.6 6.4 50 87 18 4.0x10 -14 0.51 10 sd 125-11-21-021 0.111 x 0.111 (2.8 x 2.8) -40 to 110 180 2.5 10.0 50 135 28 5.2x10 -14 0.80 15 sd 172-11-21-021 (isolated) ?221 0.185 x 0.125 (4.7 x 3.18) -40 to 110 100 5.0 20.0 50 255 53 7.0x10 -14 1.5 30 sd 200-11-21-041 (isolated) ?241 0.200 (dia.) (5.08 dia.) -40 to 110 70 6.5 26.0 50 345 71 8.6x10 -14 2.03 32 sd 290-11-21-041 (isolated) ?241 0.300 x 0.220 (7.62 x 5.58) -40 to 110 35 13.0 52.0 50 725 150 1.2x10 -13 4.26 70 sd 445-11-21-305 0.394 x 0.394 (10 x 10) -20 to 75 15 30.0 120 50 1700 350 2.0x10 -13 10.0 140 ? 1 . dark current and shunt resistance vary with temperature as follows: for t>23 c, i d =1.09 d t i d23, r sh =0.9 d t r sh23 and for t<23 c, i d =i d23 /1.09 d t , r sh =r sh23 /0.9 d t , where d t is the temperature difference from 23 c, and i d23 and r sh23 are the dark current and shunt resistance at 23 c. 2. typical values listed. minimum value shall be 50% of typical. 3. typical values are listed in the table. maximum value is 20% higher than the typical value. 4. test conditions are v b =5v and 950nm. 5. maximum linear current specifies the level above which the output current deviates more than 10%. short circuit current saturates at approximately 10 times this level. 6. response times listed are for the rising or falling edge, and were measured at 830nm with a 50w load. shorter wavelengths will result in faster rise and fall times. ? ? ? ? ? ? general purpose pin file:///d|/web sites/api/tmpehsgpgbkzq.htm (1 of 5) [7/11/2001 10:39:04 am]
general purpose pin file:///d|/web sites/api/tmpehsgpgbkzq.htm (2 of 5) [7/11/2001 10:39:04 am]
? general purpose pin file:///d|/web sites/api/tmpehsgpgbkzq.htm (3 of 5) [7/11/2001 10:39:04 am]
? ? general purpose pin file:///d|/web sites/api/tmpehsgpgbkzq.htm (4 of 5) [7/11/2001 10:39:04 am]
? ? general purpose pin file:///d|/web sites/api/tmpehsgpgbkzq.htm (5 of 5) [7/11/2001 10:39:04 am]
|
