View V-15G-5A5-K_7021526.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

snap action switch v 121 snap action switch v general purpose s nap action switch ? industry standard design with swit ching currents of 10a to 21a ? widely used for applications where long life expectancy and high reliability is required. ? choose from a variety of levers, terminals and operating forces. ? right and left barrier options are available for the v-21 and v-16 models ? heat resistant versions of the v-15 and v-10 are available. ? rohs compliant ordering information model number legend v - - - - 1. ratin g s 21: 21 a at 250 v ac 16: 16 a at 250 v ac 2. contact gap none: 1 mm (f gap) g: 0.5 mm (g gap) 15: 15 a at 250 v ac 11: 11 a at 250 v ac 10: 10 a at 250 v ac 4: 100 gf 7. maximum operatin g force 6: 400 gf 5: 200 gf 8. special purpose t: heat resisti v e ( v -15 and v -10, only) 4. contact form 1: spdt com terminal, bottom position: com terminal, side position: 2: spst-nc 9. mountin g hole size none: 3.1 mm none: standard k: 2.9 mm 3: spst-no 4: spdt 5: spst-nc 6: spst-no 6. insulation barrier none: w itho u t barrier r: right-hand b arrier l: left-hand b arrier note: these of v al u es are for the pin pl u nger models. 3. actuator none: pin pl u nger 1: short hinge le v er 2: hinge le v er 3: long hinge le v er 4: sim u lated roller le v er 5: short hinge roller le v er 6: hinge roller le v er 5. terminals a: solder terminals c2: q u ick-connect terminal (#187) c: q u ick-connect terminal (#250) 3 4 5 2 1 7 8 9 6 (barriers a v aila b le for v -21 and v -16, only) note: cons u lt omron regarding nomenclat u re com b inations and part n u m b ers not fo u nd in this datasheet.
122 snap action switch v available combinations note: 1. ? : available model. consult omro n for specific models with standard approval. list of models thermoplastic case 21 a (of: 400 gf) note: 1. add ?g? to the part number in the appropriate location to obtain a 0.5 mm contact gap. add ?-k? to the part number in the app ropriate location to obtain 2.9 mm mounting holes. example: v-21 g 2-1c6- k 2. n ot all combinations are available. consul t omron regarding nomenclature combinations and part numbers not found in this datashe et. thermoplastic case thermosetting case modelv-21v-16v-11v-15 v-10 rated current 21 a 16 a 11 a 15 a 10 a com terminal position insulation barrier heat resistance of terminal symbol 400 gf 400 gf 200 gf 100 gf 400 gf 200 gf 200 gf 100 gf bottom n o standard ( 8 0 c) solder terminals (a) - - - ??????? quick-connect terminals (#1 8 7)(c2) - - - ??????? quick-connect terminals (#250)(c) ???????? heat resistant (150 c) solder terminals (a) - - - - - - - - - - - - ???? quick-connect terminals (#1 8 7)(c2) - - - - - - - - - - - - ???? quick-connect terminals (#250)(c) - - -- - -- - -- - -- - -- - -- - -- - - yes standard ( 8 0 c) solder terminals (a) - - - ?? - - - - - - - - - - - - - - - quick-connect terminals (#1 8 7)(c2) - - - ?? - - - - - - - - - - - - - - - quick-connect terminals (#250)(c) ??? - - - - - - - - - - - - - - - side n o standard ( 8 0 c) solder terminals (a) - - - - - - - - - - - - ???? quick-connect terminals (#1 8 7)(c2) - - - - - - - - - - - - ???? quick-connect terminals (#250)(c) ? - - - - - - - - - - - - - - - - - - - - - common terminal position contact form terminal style actuator bottom spdt quick-connect (#250) (c) v-21-1c6 v-21-1cr6 v-21-1cl6 spst- n c v-21-2c6 v-21-2cr6 v-21-2cl6 spst- n o v-21-3c6 v-21-3cr6 v-21-3cl6 spdt v-211-1c6 v-211-1cr6 v-211-1cl6 v-212-1c6 v-212-1cr6 v-212-1c6 v-213-1c6 v-213-1cr6 v-213-1cl6 v-214-1c6 v-214-1cr6 v-214-1cl6 v-215-1c6 v-215-1cr6 v-215-1cl6 v-216-1c6 v-216-1cr6 v-216-1cl6 without barrier without barrier ri g ht-hand barrier left-hand barrier pin plunger short hinge lever hinge lever long hinge lever simulated roller lever short hinge roller lever hinge roller lever
snap action switch v 123 16 a (of: 200 gf) 11 a (of: 100 gf) note: 1. add ?g? to the part number in the appropriate location to obtain a 0.5 mm contact gap. add ?-k? to the part number in the app ropriate location to obtain 2.9 mm mounting holes. examples: 1) v-16 g 3-1c25- k 2) v-11 g -1a4- k 2. n ot all combinations are available. cons ult omron regarding nomenclature combinations and part numbers not found in this datashe et. common terminal position contact form terminal style actuator bottom spdt a v-16-1a5 v-16-1ar5 v-16-1al5 c2 v-16-1c25 v-16-1c2r5 v-16-1c2l5 c v-16-1c5 - - - - - - spst- n ca v-16-2a5 v-16-2ar5 v-16-2al5 c2 v-16-2c25 v-16-2c2r5 v-16-2c2l5 c v-16-2c5 - - - - - - spst- n oa v-16-3a5 v-16-3ar5 v-16-3al5 c2 v-16-3c25 v-16-3c2r5 v-16-3c2l5 c v-16-3c5 - - - - - - spdt a v-161-1a5 v-161-1ar5 v-161-1al5 c2 v-161-1c25 v-161-1c2r5 v-161-1c2l5 c v-161-1c5 - - - - - - a v-162-1a5 v-162-1ar5 v-162-1al5 c2 v-162-1c25 v-162-1c2r5 v-162-1c2l5 c v-162-1c5 - - - - - - a v-163-1a5 v-163-1ar5 v-163-1al5 c2 v-163-1c25 v-163-1c2r5 v-163-1c2l5 c v-163-1c5 - - - - - - a v-164-1a5 v-164-1ar5 v-164-1al5 c2 v-164-1c25 v-164-1c2r5 v-164-1c2l5 c v-164-1c5 - - - - - - a v-165-1a5 v-165-1ar5 v-165-1al5 c2 v-165-1c25 v-165-1c2r5 v-165-1c2l5 c v-165-1c5 - - - - - - a v-166-1a5 v-166-1ar5 v-166-1al5 c2 v-166-1c25 v-166-1c2r5 v-166-1c2l5 c v-166-1c5 - - - - - - without barrier without barrier ri g ht-hand barrier left-hand barrier pin plunger short hinge lever hinge lever long hinge lever simulated roller lever short hinge roller lever hinge roller lever common terminal position contact form terminal style actuator bottom spdt a v-11-1a4 c2 v-11-1c24 c v-11-1c4 a v-111-1a4 c2 v-111-1c24 c v-111-1c4 a v-112-1a4 c2 v-112-1c24 c v-112-1c4 a v-113-1a4 c2 v-113-1c24 c v-113-1c4 a v-114-1a4 c2 v-114-1c24 c v-114-1c4 a v-115-1a4 c2 v-115-1c24 c v-115-1c4 a v-116-1a4 c2 v-116-1c24 c v-116-1c4 without barrier pin plunger short hinge lever hinge lever long hinge lever simulated roller lever short hinge roller lever hinge roller lever
124 snap action switch v thermosetting case standard models - 15 a / 10 a note: 1. for spst- n c and spst- n o with levers consult omron. 2. n ot all combinations are available. consul t omron regarding nomenclature combinations and part numbers not found in this datashe et. heat resistant models (up to 150 c) - 15 a / 10a note: 1. add ?g? to the part number in the appropriate location to obtain a 0.5 mm contact gap. add ?-k? to the part number in the app ropriate location to obtain 2.9 mm mounting holes. add ?c2? to the part number in the appropriate location to obtain versions with #1 8 7 quick- connect terminals. example: 1) v-15 g 1-1c25-t- k 2. n ot all combinations are available. consul t omron regarding nomenclature combinations and part numbers not found in this datashe et. common terminal position contact form terminal style actuator 15 a 10 a 200 gf 200 gf 100 gf bottom spdt a v-15g-1a5-k v-10g-1a5-k v-10g-1a4-k c2 v-15g-1c25-k v-10g-1c25-k v-10g-1c24-k c v-15g-1c5-k ? ? spst- n ca v-15g-2a5-k v-10g-2a5-k v-10g-2a4-k c2 v-15g-2c25-k v-10g-2 c25-k v-10g-2c24-k spst- n oa v-15g-3a5-k v-10g-3a5-k v-10g-3a4-k c2 v-15g-3c25-k v-10g-3 c25-k v-10g-3c24-k c v-15g-3c5-k ? ? side spdt a v-15g-4a5-k v-10g-4a5-k v-10g-4a4-k spst- n c V-15G-5A5-K v-10g-5a5-k v-10g-5a4-k spst- n o v-15g-6a5-k v-10g-6a5-k v-10g-6a4-k bottom spdt a v-15g1-1a5-k v-10g1- 1a5-k v-10g1-1a4-k c2 v-15g1-1c25-k v-10g1- 1c25-k v-10g1-1c24-k a v-15g2-1a5-k v-10g2- 1a5-k v-10g2-1a4-k c2 v-15g2-1c25-k v-10g2- 1c25-k v-10g2-1c24-k a v-15g3-1a5-k v-10g3- 1a5-k v-10g3-1a4-k c2 v-15g3-1c25-k v-10g3-1c25-k v-10g3-1c24-k a v-15g4-1a5-k v-10g4- 1a5-k v-10g4-1a4-k c2 v-15g4-1c25-k v-10g4-1c25-k v-10g4-1c24-k a v-15g5-1a5-k v-10g5- 1a5-k v-10g5-1a4-k c2 v-15g5-1c25-k v-10g5-1c 25-k v-10g5-1c24-k a v-15g6-1a5-k v-10g6- 1a5-k v-10g6-1a4-k c2 v-15g6-1c25-k ? v-10g6-1c24-k common terminal position contact form terminal style actuator 15 a 10 a 200 gf 100 gf bottom spdt solder terminals (a) v-15-1a5-t v-10-1a4-t v-151-1a5-t v-101-1a4-t v-152-1a5-t v-102-1a4-t v-153-1a5-t v-103-1a4-t v-154-1a5-t v-104-1a4-t v-155-1a5-t v-105-1a4-t v-156-1a5-t v-106-1a4-t pin plunger short hinge lever hinge lever long hinge lever simulated roller lever short hinge roller lever hinge roller lever pin plunger short hinge lever hinge lever long hinge lever simulated roller lever short hinge roller lever hinge roller lever
snap action switch v 125 specifications ratings (reference values) note: 1. the above current values are the normal current values of model s with a contact gap of 1 mm (gap f), which vary with the normal current values of models with a contact gap of 0.5 mm (gap g). 2. inductive load has a power factor of 0.4 min. (ac) and a time constant of 7 ms max. (dc). 3. lamp load has an inrush current of 10 times the steady-state current. 4. motor load has an inrush current of 6 times the steady-state current. 5. the ratings values apply under the following test conditions: ambient temperature: 20 2 c, ambient humidity: 65 5%, operating frequency: 30 operations/min approved standards ul1054 (file no. e41515) csa c22.2 no.55 (file no. lr21642) en 6105 8 -1 (file no. 12960 8 , vde approval) testing conditions: 5e4 ( 50,000 operations), t105 (0 c to 105 c) en 6105 8 -1 (file no. t9451451, tv rheinland approval) testing conditions: 5e4 (50,000 operations), t 8 5 (0 c to 8 5 c) type rated voltage non-inductive load inductive load resistive load lamp load inductive load motor load nc no nc no nc no nc no v-21 250 vac 21 a 3 a 12 a 4 a 8 vdc 30 vdc 125 vdc 250 vdc 21 a 14 a 0.6 a 0.3 a 5 a 5 a 0.1 a 0.05 a 12 a 12 a 0.6 a 0.3 a 7 a 5 a 0.1 a 0.05 a v-16 250 vac 16 a 2 a 10 a 3 a 8 vdc 30 vdc 125 vdc 250 vdc 16 a 10 a 0.6 a 0.3 a 4 a 4 a 0.1 a 0.05 a 10 a 10 a 0.6 a 0.3 a 6 a 4 a 0.1 a 0.05 a v-15 250 vac 15 a 2 a 10 a 3 a 8 vdc 30 vdc 125 vdc 250 vdc 15 a 10 a 0.6 a 0.3 a 4 a 4 a 0.1 a 0.05 a 10 a 10 a 0.6 a 0.3 a 6 a 4 a 0.1 a 0.05 a v-11 250 vac 11 a 1.5 a 6 a 2 a 8 vdc 30 vdc 125 vdc 250 vdc 11 a 6 a 0.6 a 0.3 a 3 a 3 a 0.1 a 0.05 a 6 a 6 a 0.6 a 0.3 a 3 a 3 a 0.1 a 0.05 a v-10 250 vac 10 a 1.5 a 6 a 2 a 8 vdc 30 vdc 125 vdc 250 vdc 10 a 6 a 0.6 a 0.3 a 3 a 3 a 0.1 a 0.05 a 6 a 6 a 0.6 a 0.3 a 3 a 3 a 0.1 a 0.05 a rated voltage v-21 v-16 v-15 v-11 v-10 125 vac 21 a, 1/2 hp 16 a, 1/2 hp 15 a, 1/2 hp 11 a, 1/3 hp 10 a, 1/3 hp 250 vac 125 vdc 0.6 a 250 vdc 0.3 a rated voltage v-21 v-16 v-11 250 vac 20 (4) a 16 (4) a 11 (3) a rated voltage v-15 v-10 250 vac 15 a 10 a 250 vdc 0.3 a
126 snap action switch v characteristics note: 1. data shown are of initial value. 2. the dielectric strength shown is measured using a separator between the switch and metal mounting plate. 3. for pin plunger models, the above values apply for use at both th e free position and total travel position. for lever models, t hey apply at the total travel position. 4. for testing conditions, contact your omro n sales representative. contact specifications note: minimum applicable loads are indicated by n standard reference values. this value represents the failure rate at a 60% ( 60 ) reliability level (jis c5003). the equation 60 =0.5 x 10 -6 / operations indicates that a failure rate of 1/ 2,000,000 operations can be expected at a reliability level of 60% operating speed 0.1 mm to 1 m/s (plunger models) operating frequency mechanical: 600 operations/minute, max. electrical: 30 operations/minute, max. insulation resistance 100 m min. (at 500 vdc) contact resistance 15 m max. dielectric strength (see note 2) 1,000 vac, 50/60 hz for 1 min between terminals of the same polarity v-21, v-16 and v-11: 2,000 vac, 50/60 hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts v-15 and v-10: 1,500 vac, 50/60 hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts vibration resistance (see note 3) malfunction: 10 to 55 hz, 1.5-mm double amplitude shock resistance (see note 3) destruction: 1,000 m/s 2 (approx. 100g) max. malfunction: v-21/v-16/v-15: 300 m/s 2 (approx. 30g) max. v-11/v10: 200 m/s 2 (approx. 20g) max. life expectancy mechanical: 50,000,000 operations min. (60 operations/minute) electrical: v-21/v-16/v-15: 100,000 operat ions min. (30 operations/minute) (v-15 heat resistive: 20,000 operations min. (30 ops/minute)) v-11/v-10: 300,000 operations min. (30 operations/minute) (v-10 heat resistive: 50,000 operations min. (30 ops/minute)) degree of protection iec ip40 degree of protection against electric shock class i proof tracking index (pti) 175 ambient operating temperature -25 c to 8 0 c (at 60% rh max.) with no icing -25 c to 150 c for heat resistive models (at 60% rh max.) with no icing. ambient operating humidity 8 5% max. (for 5 c to 35 c) weight approx. 6.2 g (plunger models) item v-21 v-16 v-15 v-11 v-10 contact specification rivet material silver alloy silver gap (standard value) 1 mm (f gap type) or 0.5 mm (g gap type) inrush current n c 50 a max. 40 a max. 36 a max. 24 a max. n o minimum applicable load 160 ma at 5 vdc
snap action switch v 127 engineering data contact form * the spst- n c and spst- n o contact form types listed in the ordering information tables are for pin plunger models only. for information concerning lever models consult omron. barrier direction (v-21 and v-16) mounting holes all switches may be panel mounted using m3 mounting screws with plane washers or spring washers to securely mount the switch. tighten the screws to a torque of 0.39 to 0.59 n m. mechanical service life electrical service life (pin plunger models) (pin plunger models) v-21/-16/-15/-10 n u m b er of operations (x10 ) 6 200 100 50 10 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 (1.6) 1.8 am b ient temperat u re: 20 2 c am b ient h u midity: 65 5 % w itho u t load operating fre qu ency: 600 operations/min v -10 (0.98 n {100 gf}), v -11 v -10 (1.96 n {200 gf}) v -15 v -16 v -21 ot rated v al u e f u ll stroke ot (mm) v-21/-16/-15 operating fre qu ency: 60 operations/min cos = 1, 250 v ac 5 2 1 0.5 0.3 0.1 0 4 8 1216202428 v -21 v -15 v -16 s w itching c u rrent (a) n u m b er of operations (x10 ) 6 5 2 1 0.5 0.3 0.1 0 0.5 1 2 3 4 5 6 7 8 9 10 11 12 v -10 v -11 v-11/-10 s w itching c u rrent (a) am b ient temperat u re: 20 2 c am b ient h u midity: 65 5 % operating fre qu ency: 60 operations/min cos = 1, 250 v ac n u m b er of operations (x10 ) 6 common terminal position contact form spdt spst-nc* spst-no* bottom type side type ri g ht-hand barrier left-hand barrier t w o, 3.1-dia. mo u nting holes or m3 scre w holes 10.3 0.1 22.2 0.1
12 8 snap action switch v dimensions terminals note: 1. unless otherwise specifi ed, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions 2. the following table is for the spdt contact specific ations. two terminals will be available for spst- n o or spst- n c contact specifications. for terminal positions, refer to the above contact form 3. right-angle pcb terminal type is available with some m odels (not shown). drawings will be provided if requested. d5: pins at right angles, to the right d6: pins at right angle, to the left terminal type solder terminal (a) quick-connect terminal (#1 8 7) (c2) quick-connect terminal (#250) (c) com bottom position com side position terminal dimensions t = 0.5 three, solder terminals (10) 2.9 (6.5) (5.5) t = 0.5 three, qu ick-connect terminals (#187) (10) 2.9 (6.5) (5.5) t = 0.8 three, qu ick-connect terminals (#250) (12.0) 3.2 (7.7) (4.9) (10) 2.4 (6.5) (5.5) (10) 2.4 (6.5) (5.5) (12.0) 3.6 (7.7) (4.9) 1.6 dia. 2.4 dia. 4.75 0.1 6.35 3.2 (see note) note: indicates the length to the center of the 1.6-dia. holes 1.6-dia. terminal hole 4.75 0.1 3.2 6.35 1.65-dia. terminal hole 6.35 0.1 3.95 8.1
snap action switch v 129 dimensions and operating characteristics thermoplastic case models note: 1. unless otherwise specified, all units are in millim eters and a tolerance of 0.4 mm applies to all dimensions 2. the following illustrations and drawings are for quick-connect terminals (#250) (terminals c). v models also incorporate termin als a and c2, which are omitted from the following drawings. refer to terminals section for the dimensions of these terminals. 3. the @ in the model number is for the terminal code. 4. the illustrations for v-21, v-16 and v-11 show a hole size of 3.1 mm. v-21, v-16 and v-11 models with a suffix ?k? have a hol e size of 2.9 mm. 5. the operating characteristics are for operation in the a direction ( ). pin plunger models ? (without barrier) v-21-1 6 v-16-1 5 v-11-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t=0.8 three, qu ick-connect terminals (#250) 20.2 0.25 2.8 1.6 2.8 10.3 0.1 pt op 22.2 0.1 2.8 (12.0) 27.8 39.8 0.8 2.8 8.4 15.9 19.1 0.6 4.2 2.8 10.3 (with ri g ht-hand barrier) v-21-1 r6 v-16-1 r5 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t=0.8 three, qu ick-connect terminals (#250) 20.2 0.25 2.8 1.6 2.8 10.3 0.1 pt op 22.2 0.1 2.8 (12.0) 27.8 39.8 0.8 40.2 2.8 15.9 8.4 19.1 21.9 0.6 4.2 2.8 0.6 10.3 a a (with left-hand barrier) v-21-1 l6 v-16-1 l5 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t=0.8 three, qu ick-connect terminals (#250) 2.8 0.6 4.2 0.6 10.3 2.8 19.1 15.9 8.4 21.9 1.6 20.2 0.25 2.8 2.8 (12.0) 2.8 27.8 39.8 0.8 22.2 0.1 40.2 10.3 0.1 pt op a characteristics v-21-1 @ 6 v-16-1 @ 5 of max. 400 gf 200 gf rf min. 8 0 gf 50 gf pt max. 1.2 mm ot min. 1.0 mm md max. 0.4 mm op 14.7 0.4 mm characteristics v-11-1 @ 4 v-11-1 @ 5 of max. 100 gf 200 gf rf min. 20 gf 50 gf pt max. 1.2 mm ot min. 1.0 mm md max. 0.4 mm op 14.7 0.4 mm
130 snap action switch v note: 1. unless otherwise specifi ed, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions 2. the following illustrations and drawings are for quick-connect terminals (#250) (termina ls c). v models also incorporate termin als a and c2, which are omitted from the following drawings. refer to te r m i n a l s section for the dimensions of these terminals. 3. the @ in the model number is for the terminal code. 4. the illustrations for v-21, v-16 and v-11 sh ow a hole size of 3.1 mm. v-21, v-16 and v-11 models with a suffix ?k? have a hol e size of 2.9 mm. 5. the operating characteristics are for operation in the a direction ( ). short hinge lever models hinge lever models long hinge lever models ? 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.8 three, qu ick-connect terminals (#250) 22.1 8.1 pt op 2.8 10.3 0.1 2.8 (12.0) 27.8 22.2 0.1 39.8 0.8 1.6 2.8 8.4 15.9 19.1 0.6 2.8 4.3 10.3 note: stainless-steel le v er a characteristics v-211-1 @ 6 v-161-1 @ 5 v-111-1 @ 4 of max. 400 gf 200 gf 100 gf rf min. 50 gf 50 gf 15 gf pt max. 1.6 mm ot min. 0. 8 mm md max. 0.6 mm op 15.2 0.5 mm 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.8 three, qu ick-connect terminals (#250) 35.6 0.8 8.1 1.6 pt op 2.8 10.3 0.1 22.2 0.1 (12.0) 2.8 27.8 39.8 0.8 2.8 15.9 8.4 19.1 0.6 2.8 4.3 10.3 v-212-1 6 v-162-1 5 v-112-1 4 note: stainless-steel le v er a characteristics v-212-1 @ 6 v-162-1 @ 5 v-112-1 @ 4 of max. 250 gf 125 gf 60 gf rf min. 25 gf 14 gf 6 gf pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 15.2 1.2 mm 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.8 three, qu ick-connect terminals (#250) 59.4 0.8 pt op 2.8 10.3 0.1 22.2 0.1 (12.0) 2.8 27.8 39.8 0.8 2.8 8.4 15.9 19.1 0.6 2.8 4.3 10.3 v-213-1 6 v-163-1 5 v-113-1 4 note: stainless-steel le v er 1.6 a characteristics v-213-1 @ 6 v-163-1 @ 5 v-113-1 @ 4 of max. 130 gf 70 gf 35 gf rf min. 12 gf 6 gf - - - pt max. 9.0 mm ot min. 2.0 mm 3.2 mm md max. 2. 8 mm op 15.2 2.6 mm 15.2 mm +2.6 ? 3.2
snap action switch v 131 note: 1. unless otherwise specified, all units are in millim eters and a tolerance of 0.4 mm applies to all dimensions 2. the following illustrations and drawings are for quick-connect terminals (#250) (terminals c). v models also incorporate termin als a and c2, which are omitted from the following drawings. refer to terminals section for the dimensions of these terminals. 3. the @ in the model number is for the terminal code. 4. the illustrations for v-21, v-16 and v-11 show a hole size of 3.1 mm. v-21, v-16 and v-11 models with a suffix ?k? have a hol e size of 2.9 mm. 5. the operating characteristics are for operation in the a direction ( ). simulated roller lever models short hinge roller lever models hinge roller lever models ? v-214-1 6 v-164-1 5 v-114-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.8 three, qu ick-connect terminals (#250) 3.5r 32.6 0.8 8.1 1.6 pt op 2.8 10.3 0.1 22.2 0.1 (12.0) 2.8 27.8 39.8 0.8 0.6 3 . 48 . 2 10.3 note: stainless-steel le v er 2.8 15.9 19.1 8.4 a characteristics v-214-1 @ 6 v-164-1 @ 5 v-114-1 @ 4 of max. 250 gf 125 gf 60 gf rf min. 25 gf 14 gf 6 gf pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 1 8 .7 1.2 mm note: 1. stainless-steel le v er 2. oilless polyacetar resin roller v-215-1 6 v-165-1 5 v-115-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note 1) 4.8 dia. 4.8 (see note 2) t=0.8 three, qu ick-connect terminals (#250) 20.1 8.1 1.6 pt op 2.8 10.3 0.1 22.2 0.1 2.8 (12.0) 27.8 39.8 0.8 2.8 8.4 15.9 19.1 0.6 5.1 10.3 a characteristics v-215-1 @ 6 v-165-1 @ 5 v-115-1 @ 4 of max. 4 8 0 gf 240 gf 120 gf rf min. 50 gf 50 gf 15 gf pt max. 1.6 mm ot min. 0. 8 mm md max. 0.6 mm op 20.7 0.6 mm v-216-1 6 v-166-1 5 v-116-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note 1) 4.8 dia. 4.8 (see note 2) t=0.8 three, qu ick-connect terminals (#250) 34.0 0.8 8.1 1.6 pt op 2.8 10.3 0.1 22.2 0.1 (12.0) 2.8 27.8 39.8 0.8 2.8 19.1 0.6 5.1 10.3 15.9 8.4 note: 1. stainless-steel le v er 2. oilless polyacetar resin roller a characteristics v-216-1 @ 6 v-166-1 @ 5 v-116-1 @ 4 of max. 250 gf 125 gf 60 gf rf min. 25 gf 14 gf 6 gf pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 20.7 1.2 mm
132 snap action switch v thermosetting case models note: 1. unless otherwise specifi ed, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions 2. the following illustrations are for quick-connect terminals (#250) (terminals c). refer to terminals section for the dimensions of other terminals. 3. the @ in the model number is for the terminal code. 4. the illustrations show models with a suffix ?k ?, which have a hole size of 2.9 mm. omit the ?k? to obtain models with hole size = 3.1 mm. 5. the operating characteristics are for operation in the a direction ( ). pin plunger models short hinge lever models hinge lever models long hinge lever models ? 2.9 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t=0.5 three, solder terminals 20.2 0.25 2.8 2.8 10.3 0.1 pt op 22.2 0.1 2.8 27.8 (10) 37.8 0.8 15.9 18.8 4.2 2.8 10.3 a characteristics v-15g-1 @ 5-k v-10g-1 @ 5-k v-10g-1 @ 4-k of max. 200 gf 100 gf rf min. 50 gf 20 gf pt max. 1.2 mm ot min. 1.3 mm md max. 0.3 mm op 14.7 0.4 mm v-15g1-1 5-k v-10g1-1 5-k v-10g1-1 4-k 2.9 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.5 three, solder terminals 22.1 8.1 pt 2.8 22.2 0.1 2.8 27.8 (10) 37.8 0.8 15.9 18.8 4.3 2.8 10.3 op 10.3 0.1 note: stainless-steel le v er a characteristics v-15g1-1 @ 5-k v-10g1-1 @ 5-k v-10g1-1 @ 4-k of max. 200 gf 100 gf rf min. 50 gf 15 gf pt max. 1.5 mm ot min. 1.0 mm md max. 0.5 mm op 15.2 0.5 mm v-15g2-1 5-k v-10g2-1 5-k v-10g2-1 4-k 2.9 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.5 three, solder terminals 35.6 0.8 8.1 pt op 2.8 10.3 0.1 22.2 0.1 2.8 27.8 (10) 37.8 0.8 15.9 18.8 4.3 2.8 10.3 note: stainless-steel le v er a characteristics v-15g2-1 @ 5-k v-10g2-1 @ 5-k v-10g2-1 @ 4-k of max. 125 gf 60 gf rf min. 14 gf 6 gf pt max. 3.3 mm ot min. 2.3 mm md max. 0. 8 mm op 15.2 1.2 mm 15.2 mm +2.6 ? 3.2 v-15g3-1 5-k v-10g3-1 5-k v-10g3-1 4-k 2.9 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.5 three, solder terminals 22.2 0.1 27.8 2.8 (10) 15.9 18.8 10.3 0.1 op pt 8.1 4.3 2.8 10.3 37.8 0.8 59.4 0.8 2.8 note: stainless-steel le v er a characteristics v-15g3-1 @ 5-k v-10g3-1 @ 5-k v-10g3-1 @ 4-k of max. 70 gf 35 gf rf min. 6 gf - - - gf pt max. 9.0 mm 7.6 mm ot min. 3.0 mm 3.2 mm md max. 2.0 mm op 15.2 2.6 mm
snap action switch v 133 note: 1. unless otherwise specified, all units are in millim eters and a tolerance of 0.4 mm applies to all dimensions 2. the following illustrations are for quick-connect terminals (#250) (terminals c). refer to te r m i n a l s section for the dimensions of other terminals. 3. the @ in the model number is for the terminal code. 4. the illustrations show models with a suffix ?k ?, which have a hole size of 2.9 mm. omit the ?k? to obtain mo dels with hole size = 3.1 mm. 5. the operating characteristics are for operation in the a direction ( ). simulated roller lever models short hinge roller lever models hinge roller lever models accessories refer to the ?v/vx/d3c common accessories? datasheet for inform ation regarding val, vam and vav external actuators (sold separa tely). ? v-15g4-1 5-k v-10g4-1 5-k v-10g4-1 4-k 3.5r 2.9 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.5 three, solder terminals 22.2 0.1 27.8 2.8 (10) 15.9 18.8 10.3 0.1 op pt 8.1 4.3 2.8 10.3 37.8 0.8 32.6 0.8 2.8 note: stainless-steel le v er a characteristics v-15g4-1 @ 5-k v-10g4-1 @ 5-k v-10g4-1 @ 4-k of max. 125 gf 60 gf rf min. 14 gf 6 gf pt max. 3.3 mm ot min. 2.3 mm md max. 0. 8 mm op 1 8 .7 1.2 mm 4.8 dia. 4.8 (see note 2) 2.9 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note 1) 22.2 0.1 27.8 2.8 (10) 15.9 18.8 10.3 0.1 op pt 8.1 5.1 10.3 37.8 0.8 20.1 2.8 v-15g5-1 5-k v-10g5-1 5-k v-10g5-1 4-k note: 1. stainless-steel le v er 2. oilless polyacetar resin roller a t=0.5 three, solder terminals characteristics v-15g5-1 @ 5-k v-10g5-1 @ 5-k v-10g5-1 @ 4-k of max. 240 gf 120 gf rf min. 50 gf 15 gf pt max. 1.5 mm ot min. 1.0 mm md max. 0.5 mm op 20.7 0.6 mm v-15g6-1 5-k v-10g6-1 5-k v-10g6-1 4-k 4.8 dia. 4.8 (see note 2) 2.9 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note 1) 22.2 0.1 27.8 2.8 (10) 15.9 18.8 10.3 0.1 op pt 8.1 5.1 10.3 37.8 0.8 34.0 0.8 2.8 note: 1. stainless-steel le v er 2. oilless polyacetar resin roller a t=0.5 three, solder terminals characteristics v-15g6-1 @ 5-k v-10g6-1 @ 5-k v-10g6-1 @ 4-k of max. 125 gf 60 gf rf min. 14 gf 6 gf pt max. 3.3 mm ot min. 2.3 mm md max. 0. 8 mm op 20.7 1.6 mm
134 snap action switch v precautions be sure to read the precautions and inform ation common to all snap action and detecti on switches, contained in the technical us er?s guide, ?snap action switches, technical information? for correct use. correct use terminal connection to solder the lead to the solder terminal, apply a soldering iron rated at 60 w max. quickly (within 5 seconds) with the actuator at the free position. n ote that applying a soldering iron for too long a time or using one that is rated at more than 60 w may degrade the switch characteris- tics. use an appropriate mating connector for #1 8 7 or #250 quick connect terminals. specifications approved by tv rheinland according to en6105 8 -1 appropriate cable size (mm 2 ) operation make sure that the operating body pushes the switch actuator with an adequate force when the switch is to be operated, and that it does not touch the actuator when the switch is released. do not change the operating position by modifying the actuator. do not use the switch in a application where the operating speed is extremely slow or the actuator is set in the midpoint between the free position and operating position. install the pin plunger switch so that the operating force is applied in alignment with the stroke of the actuator. the switch should be set so that its stroke is in the range of 60 to 90% of the rated ot (minimum value) when the switch has been operated. cautions insulation distance according to e n 6105 8 -1, the minimum insulation thickness for this switch should be 1.1 mm and minimum clearance distance between the terminal and mounting plate should be 1.0 mm. if the insulation distance cannot be provided in the product incorporating the switch, either use a switch with insulation barrier or use a separator to ensure sufficient insulation distance. model solder terminal v-10 0.75, 1.25, 2.0 v-15 1.25, 2.0
snap action switch v memo
snap action switch v omron on-line global - http://www.omron.com usa - http://www.components.omron.com cat. n o. x303-e-1 printed in usa omron electronic components llc 55 e. commerce drive, suite b schaumburg, il 60173 8 47- 88 2-22 88 11/10 specificat ions subject to change without notice all sales are subject to omron electronic components llc standard terms and conditions of sale, which can be found at http://www.components.omron.com/compon ents/web/webfiles.ns f/sales_terms.html all dimensions shown are in millimeters. to convert millimeters into inches, multiply by 0.0393 7. to convert grams into ounces, multiply by 0.03527.

▲Up To Search▲

Price & Availability of V-15G-5A5-K

	To Download V-15G-5A5-K Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .