panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ cm asctb222e 201203-t1 ordering information types standard type standard packing; carton: 50 pcs.; case: 200 pcs. note: please use ?m ?? -r- ? - ? ?b uilt-in resistor type. (asterisks ? ? should be ?led in from ordering information.) aut omotive micro-iso relay cm relays contact arrangement coil voltage plug-in type pc board type sealed type flux-resistant type sealed type flux-resistant type part no. part no. part no. part no. 1 form a 12 v dc cm1a-12v cm1af-12v 24 v dc cm1a-24v cm1af-24v cm1a-p-24v cm1af-p-24v 1 form c 12 v dc CM1-12V cm1f-12v 24 v dc cm1-24v cm1f-24v cm1-p-24v cm1f-p-24v plug-in type pc board type rohs compliant features ?micro-iso type terminals ?small size: 20 mm(l) 15 mm(w) 22 mm(h) .787 inch(l) .591 inch(l) .866 inch(h) ?wide line-up pc board and plug-in type, resistor inside type. 24v dc type is also available. ?compact and high-capacity 35a load switching n.o.: 35a 14v dc, n.c.: 20a 14v dc (sealed type) min. 5 10 4 n.o.: 35a 14v dc, n.c.: 20a 14v dc (flux-resistant type) min. 10 5 *12v dc type ?uses international standard iso terminal arrangement. the iso international standard terminal arrangement is used. typical applications ?fan motor ?heater ?head lump ?air compressor ?eps ?abs ?blower fan ?defogger, etc. contact arrangement 1a: 1: 1 form a 1 form c cm protective construction nil: f: sealed type flux-resistant type mounting classification nil: p: plug-in type pc board type protective element nil: r: none (standard type) with resistor inside coil voltage (dc) 12 v, 24 v
panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ cm asctb222e 201203-t1 rating 1. coil data 2. speci?ations notes: *1. this value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. *2. the upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value. please refer to ?sage ambient condition in cautions for use of automotive relays. *3. please inquire if you will be using the relay in a high temperature atmosphere. reference data nominal coil voltage pick-up voltage (at 20 c 68 f ) drop-out voltage (at 20 c 68 f ) nominal operating current [ 10%] (at 20 c 68 f ) coil resistance [ 10%] (at 20 c 68 f ) nominal operating power usable voltage range 12 v dc 3 to 7 v dc 1.2 to 4.2 v dc 125 ma 96 ? 1.5 w 10 to 16v dc 24 v dc 6 to 14 v dc 2.4 to 8.4 v dc 75 ma 320 ? 1.8 w 20 to 32v dc characteristics item speci?ations 12 v dc 24 v dc contact arrangement 1 form a 1 form c 1 form a 1 form c contact resistance (initial) typ 2m ? (by voltage drop 6v dc 1a) contact voltage drop (after electrical life test) n.o.: max. 0.5 v (by voltage drop 14 v dc 35 a) n.o.: max. 0.5 v (by voltage drop 14 v dc 35 a) n.c.: max. 0.3 v (by voltage drop 14 v dc 20 a) n.o.: max. 0.3 v (by voltage drop 28 v dc 15 a) n.o.: max. 0.3 v (by voltage drop 28 v dc 15 a) n.c.: max. 0.2 v (by voltage drop 28 v dc 8 a) contact material ag alloy (cadmium free) rating nominal switching capacity (resistive load) n.o.: 35 a 14v dc n.o.: 35 a 14v dc n.c.: 20 a 14v dc n.o.: 15 a 28v dc n.o.: 15 a 28v dc n.c.: 8 a 28v dc max. carrying current (at 85 c 185 f , continuous) n.o.: 20 a 14v dc n.o.: 20 a 14v dc n.c.: 10 a 14v dc n.o.: 15 a 28v dc n.o.: 15 a 28v dc n.c.: 8 a 28v dc nominal operating power 1.5 w, 1.7 w (with resistor inside type) 1.8 w, 2.0 w (with resistor inside type) min. switching capacity (resistive load)* 1 1 a 12v dc 1 a 24v dc electrical characteristics insulation resistance (initial) min. 20 m ? (at 500v dc, measurement at same location as ?reakdown voltage section.) breakdown voltage (initial) between open contacts 500 vrms for 1 min. (detection current: 10ma) between contacts and coil 500 vrms for 1 min. (detection current: 10ma) operate time (at nominal voltage) (at 20 c 68 f ) max. 10ms (excluding contact bounce time) (initial) release time (at nominal voltage) (at 20 c 68 f ) max. 10ms (excluding contact bounce time) (initial) mechanical characteristics shock resistance functional min. 200 m/s 2 {20g} (half-wave pulse of sine wave: 11ms; detection time: 10 s) destructive min. 1,000 m/s 2 {100g} (half-wave pulse of sine wave: 6ms) vibration resistance functional 10 hz to 500 hz, min. 44.1 m/s 2 {4.5g} destructive 10 hz to 2,000 hz, min. 44.1 m/s 2 {4.5g}, time of vibration for each direction; x, y, z direction: 4 hours expected life mechanical (at 120 cpm) min. 10 6 electrical (operating frequency: 2s on, 2s off) flux-resistant type: min. 10 5 , sealed type: min. 5 10 4 conditions conditions for operation, transport and storage* 2 ambient temperature: ?0 c to +85 c ?0 f to +185 f * 3 , humidity: 5% r.h. to 85% r.h. (not freezing and condensing at low temperature), air pressure: 86 to 106 kpa mass approx. 20 g .71 oz 1-(1). coil temperature rise (12v type) sample: cm1f-12v, 3 pcs. measured portion: inside the coil contact carrying current: 20a, 35a ambient temperature: 85 c 185 f 1-(2). coil temperature rise (24v type) sample: cm1f-24v, 4 pcs. measured portion: inside the coil contact carrying current: 0a, 15a ambient temperature: 85 c 185 f 2. max. switching capability (resistive load, initial) 12 14 16 120 100 80 60 40 20 0 35a 20a coil applied voltage, v temperature rise, c 24 28 32 120 100 80 60 40 20 0 15a 0a coil applied voltage, v temperature rise, c 0 switching current, a switching voltage, vdc 60 50 40 30 20 10 010203 04050 (n.o. side room temperature) 24v type 12v type
panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ cm asctb222e 201203-t1 3. ambient temperature and operating voltage range (12v type) 4. ambient temperature characteristics (cold/initial) 5. distribution of pick-up and drop-out voltage sample: cm1f-12v, 100pcs. 0 ambient temperature, c coil applied voltage, vdc 5 10 15 30 25 20 ? 40 ? 20 20 40 60 8085 1000 120 operation range pick-up voltage (cold start) 0 ambient temperature, c ratio against the rated voltage, % 20 40 60 70 50 30 10 80 ? 40 ? 20 20 40 60 800 100 pick-up voltage upper limit drop-out voltage lower limit 0 30 20 10 40 50 60 70 voltage, v quantity, n 1.5 2.0 2.5 3.0 3.5 4.5 5.04.0 5.5 6.0 6.5 7.01.0 pick-up voltage drop-out voltage 6. distribution of operate time sample: cm1f-12v, 30pcs. * max. 10ms standard (excluding contact bounce) 7. distribution of release time sample: cm1f-12v, 30pcs. * max. 10ms standard (excluding contact bounce) 0 30 20 10 40 25 15 5 35 time, ms quantity, n 0.5 1 1.5 2 2.5 3.5 4.5 34567 5.5 6.5 0 30 20 10 40 25 15 5 35 time, ms quantity, n 0.5 1 1.5 2 2.5 3.5 4.5 34567 5.5 6.5 8-(1). electrical life test (motor free) sample: cm1af-r-12v, 6pcs. load: 16 a 13.5 v dc cooling fan motor actual load (free condition) operating frequency: on 2s, off 6s ambient temperature: room temperature circuit change of pick-up and drop-out voltage change of contact resistance cooling fan motor 13.5v m m 0 no. of operations, 10 4 pick-up and drop-out voltage, v max. max. min. min. 2 1 4 6 8 9 7 5 3 10 0102035 pick-up voltage drop-out voltage 0 no. of operations, 10 4 contact resistance, m ? max. min. 2 1 4 6 8 9 7 5 3 10 0102035 x load current waveform inrush current: 85a, steady current: 18a, 500ms 20a
panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ cm asctb222e 201203-t1 dimensions (mm inch ) 8-(2). electrical life test (halogen lamp load) sample: cm1af-r-12v, 6pcs. load: 20a 13.5v dc operating frequency: on 1s, off 14s ambient temperature: room temperature change of pick-up and drop-out voltage change of contact resistance 0 no. of operations, 10 4 pick-up and drop-out voltage, v max. max. min. min. 2 1 4 6 8 9 7 5 3 10 0510 pick-up voltage drop-out voltage 0 no. of operations, 10 4 contact resistance, m ? max. min. 2 1 4 6 8 9 7 5 3 10 0510 x the cad data of the products with a cad data mark can be downloaded from: http://industrial.panasonic.com/ac/e/ 1. micro-iso plug-in type (1 form c) external dimensions sealed by epoxy resin 86 85 87 87 30 2-1.75 dia. 3-1.5 dia. a* 8 2.1 20 15 0.8 4.8 6.3 14 0.8 a 3.25 9 11 22 4.25 .248 .031 .433 .866 .167 2-.069 dia. .591 .083 .354 .315 .551 3-.059 dia. .787 .031 .128 .189 dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 * intervals between terminals is measured at a surface level. schematic (bottom view) including resistor type also available 30 85 86 87a 87 cad data 2. micro-iso plug-in type (1 form a) external dimensions 86 85 8 a 87 30 7 sealed by epoxy resin 2-1.75 dia. 3-1.5 dia. a* 8 2.1 20 15 0.8 4.8 6.3 14 0.8 3.25 9 11 22 4.25 2-.069 dia. .591 .248 .031 .433 .866 .167 .083 .354 .315 .551 3-.059 dia. .787 .189 .031 .128 dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 * intervals between terminals is measured at a surface level. schematic (bottom view) 30 85 86 87 including resistor type also available cad data
panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ cm asctb222e 201203-t1 for cautions f or us e , see rel a y t e c hnical in f ormation. 3. micro-iso pc board type (1 form c) external dimensions pre-soldering sealed by epoxy resin 86 85 87 a 87 30 a* 2.5 8 2.1 2.1 20 15 0.8 4.8 6.3 15 0.8 9 23 max. 1.2 1 3.5 .591 .248 .098 .031 .906 .039 .138 .083 .354 .315 .591 .031 max. .047 .083 .787 .189 dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 * dimensions (thickness and width) of terminal is measured before pre-soldering. intervals between terminals is measured at a surface level. schematic (bottom view) pc board pattern (bottom view) including resistor type also available 30 85 86 87a 87 1c type only 1c type only 87 87a 86 85 30 9.0 0.05 .354 .002 2-1.4 +0.1 0 2-.055 +.004 0 2-2.7 +0.1 0 2-.106 +.004 0 1.4 +0.1 0 .055 +.004 0 1.4 +0.1 0 .055 +.004 0 2 (or 3)-2.4 +0.1 0 2 (or 3)-.094 +.004 0 4.5 0.05 .177 .002 15.0 0.05 .591 .002 8.0 0.05 .315 .002 cad data 4. micro-iso pc board type (1 form a) external dimensions 86 85 87 a 87 30 sealed by epoxy resin pre-soldering a* 2.5 8 2.1 2.1 20 15 0.8 4.8 6.3 15 0.8 9 23 max. 1.2 1 3.5 .591 .248 .098 .031 .906 .039 .138 .031 max. .047 .083 .787 .189 .083 .354 .315 .591 dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 * dimensions (thickness and width) of terminal is measured before pre-soldering. intervals between terminals is measured at a surface level. schematic (bottom view) 30 85 86 87 including resistor type also available cad data
|
