View MIG100Q6CMA0X_6911548.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIG100Q6CMA0X 2001-08-17 1 toshiba intelligent power module silicon n channel igbt MIG100Q6CMA0X (1200v/100a 6in1) high power switching application motor control application integrates inverter, brake power circuits & control circuits (igbt drive units, protection units for short-circuit current, overcurrent, undervoltage & overtemperature) in one package. the electrodes are isolated from case. v ce (sat) = 2.4 v (typ.) ul recognized file no. e87989 weight: 385 g (typ.) equivalent circuit
MIG100Q6CMA0X 2001-08-17 2 package dimensions toshiba 2-123a1a unit: mm 1. v d (u) 2. fo (u) 3. in (u) 4. gnd (u) 5. v d (v) 6. fo (v) 7. in (v) 8. gnd (v) 9. v d (w) 10. fo (w) 11. in (w) 12. gnd (w) 13. v d (l) 14. fo (l) 15. open 16.open 17. in (x) 18. in (y) 19. in (z) 20. gnd (l)
MIG100Q6CMA0X 2001-08-17 3 signal terminal layout unit: mm 1. v d (u) 2. fo (u) 3. in (u) 4. gnd (u) 5. v d (v) 6. fo (v) 7. in (v) 8. gnd (v) 9. vd (w) 10. fo (w) 11. in (w) 12. gnd (w) 13. vd (l) 14. fo (l) 15. open 16.open 17. in (x) 18. in (y) 19. in (z) 20. gnd (l)
MIG100Q6CMA0X 2001-08-17 4 maximum ratings (t j = 25c) stage characteristic condition symbol ratings unit supply voltage p-n power terminal v cc 900 v collector-emitter voltage D v ces 1200 v collector current tc = 25c, dc i c 100 a forward current tc = 25c, dc i f 100 a collector power dissipation tc = 25c p c 600 w inverter junction temperature D t j 150 c control supply voltage v d -gnd terminal v d 20 v input voltage in-gnd terminal v in 20 v fault output voltage fo-gnd (l) terminal v fo 20 v control fault output current fo sink current i fo 14 ma operating temperature D tc ? 20 ~ +100 c storage temperature range D t stg ? 40 ~ +125 c isolation voltage ac 1 minute v iso 2500 v module screw torque m5 D 3 nm electrical characteristics 1. inverter stage characteristic symbol test condition min typ. max unit t j = 25c D D 1 collector cut-off current i cex v ce = 1200 v t j = 125c D D 10 ma t j = 25c D 2.4 2.8 collector-emitter saturation voltage v ce (sat) v d = 15 v, i c = 100 a v in = 15 v 0 v t j = 125c D D 3.2 v forward voltage v f i f = 100 a, t j = 25c D 2.5 3.1 v t on D 1.0 2.0 t c(on) D 0.6 1.2 t rr D 0.3 0.6 t off D 2.0 3.0 switching time t c(off) v cc = 600 v, i c = 100 a v d = 15 v, v in = 15 v ? 0 v, t j = 25c, inductive load (note 1) D 0.3 0.7 s note 1: switching time test circuit & timing chart.
MIG100Q6CMA0X 2001-08-17 5 2. control stage ( t j = 25c ) characteristic symbol test condition min typ. max unit high side i d (h) D 8 12 control circuit current low side i d (l) v d = 15 v D 34 50 ma input-on signal voltage v in (on) v d = 15 v 1.4 1.6 1.8 input-off signal voltage v in (off) D 2.2 2.5 2.8 v protection i fo (on) D 10 12 fault output current normal i fo (off) v d = 15 v ,t j 125c D D 0.1 ma overcurrent protection trip level inverter oc v d = 15 v, t j 125c 160 D D a short-circuit current protection trip level inverter sc v d = 15 v, t j 125c 200 D D a overcurrent cut-off time t off (oc) v d = 15 v D 5 D s trip level ot 110 118 125 overtemperature protection reset level otr case temperature D 98 D c trip level uv 11.0 12.0 12.5 control supply under voltage protection reset level uvr D 12.0 12.5 13.0 v fault output pulse width t fo v d = 15 v 1 2 3 ms 3. thermal resistance ( tc = 25c ) characteristic symbol test condition min typ. max unit igbt D D 0.208 junction to case thermal resistance r th (j-c) frd D D 0.50 c / w case to fin thermal resistance r th (c-f) compound is applied D 0.013 D c / w
MIG100Q6CMA0X 2001-08-17 6 switching time test circuit timing chart pg tlp559 15 v 0.1 f 47 f 15 k ? intelligent power module v d in gnd out v s gnd u (v, w) p v cc 15 v 0.1 f 47 f 15 k ? v d in gnd out v s gnd i f = 16ma n input pulse v in waveform i c waveform v ce waveform 2.5 v 1.6 v 15 v 10% 10% t off t c(off) 10% 10% t on t c(on) 90% i rr t rr 0 i rr 20% i rr 90%
MIG100Q6CMA0X 2001-08-17 7 4. recommended conditions for application characteristics symbol test condition min typ. max unit supply voltage v cc p-n power terminal D 600 800 v control supply voltage v d v d -gnd signal terminal 13.5 15 16.5 v carrier frequency fc pwm control D D 20 khz dead time tdead switching time test circuit (see page.6) (note 2) 4 D D s note 2: the table lists dead time requirements for the module input, excluding photocoupler delays. when specifying dead time requirements for the photocoupler input, please add photocoupler delays to the dead time given above. dead time timing chart t dead 15 v v in waveform v in waveform 0 15 v 0 t dead
MIG100Q6CMA0X 2001-08-17 8
MIG100Q6CMA0X 2001-08-17 9
MIG100Q6CMA0X 2001-08-17 10 turn on loss ? i c turn off loss ? i c collector current i c (a) collector current i c (a) turn off loss eoff (mj) turn on loss eon (mj) 0.1 0 1 3 100 10 40 120 60 v cc = 600 v v d = 15 v l-load : tj = 25c : tj = 125c 20 0.3 0.5 5 30 50 100 80 0.1 0 1 3 100 10 40 120 60 v cc = 600 v v d = 15 v l-load : tj = 25c : tj = 125c 20 0.3 0.5 5 30 50 100 80
MIG100Q6CMA0X 2001-08-17 11 ? toshiba is continually working to improve the quality and reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshiba products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconductor devices,? or ?toshiba semiconductor reliability handbook? etc.. ? the toshiba products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. unintended usage of toshiba products listed in this document shall be made at the customer?s own risk. ? the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba corporation for any infringements of intellectual property or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any intellectual property or other rights of toshiba corporation or others. ? the information contained herein is subject to change without notice. 000707ea a restrictions on product use

▲Up To Search▲

Price & Availability of MIG100Q6CMA0X

	To Download MIG100Q6CMA0X Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .