Part Number Hot Search : 
NP175014 E001159 D1212 CS2012 40D112K G1427 109215 LM3580
Product Description
Full Text Search
 

To Download FSCM0565RCYDTUNL Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  ?2005 fairchild semiconductor corporation www.fairchildsemi.com rev.1.1.0 fps tm is a trademark of fairchild semiconductor corporation features ? internal avalanche rugged sensefet ? low start-up current (max 40ua) ? low power consumption under 1 w at 240vac and 0.4w load ? precise fixed operating frequency (66khz) ? frequency modulation for low emi ? pulse by pulse current limiting (adjustable) ? over voltage protection (ovp) ? over load protection (olp) ? thermal shutdown function (tsd) ? auto-restart mode ? under voltage lock out (uvlo) with hysteresis ? built-in soft start (15ms) application ? smps for vcr, svr, stb, dvd and dvcd ? adaptor ? smps for lcd monitor related application notes ? an-4137 : design guidelines for off-line flyback converters using fairchild power switch (fps) ? an-4140 : transformer design c onsideration for off-line flyback converters using fairchild power switch ? an-4141 : troubleshooting and design tips for fairchild power switch flyback applications ? an-4148 : audible noise reduction techniques for fps applications description the fscm0565r is an integrated pulse width modulator (pwm) and sensefet specifically designed for high performance offline switch mode power supplies (smps) with minimal external components. this device is an integrated high voltage power switching regulator which combines an avalanche rugged sensefet with a current mode pwm control block. the pwm controller includes integrated fixed frequency oscillator, under voltage lockout, leading edge blanking (leb), optimized gate driver, internal soft start, temperature compensated precise current sources for a loop compensation, and self protection circuitry. compared with a discrete mosfet and pwm controller solution, it can reduce total cost, component count, size , and weight while simultaneously increasing efficiency, productivity, and system reliability. this device is a basic platform well suited for cost effective designs of flyback converters. table 1. maximum output power notes: 1. typical continuous power in a non-ventilated enclosed adapter measured at 50 c ambient. 2. maximum practical continuous power in an open-frame design at 50 c ambient. 3. 230 vac or 100/115 vac with doubler. typical circuit figure 1. typical flyback application output power table product 230vac 15% (3) 85-265vac adapt- er (1) open frame (2) adapt- er (1) open frame (2) fscm0565rj 50w 65w 40w 50w fscm0765rj 65w 70w 50w 60w fscm0565ri 50w 65w 40w 50w fscm0765ri 65w 70w 50w 60w fscm0565rg 70w 85w 60w 70w fscm0765rg 85w 95w 70w 85w drain gnd vfb vcc pwm ac in dc out i limit fscm0565r green mode fairchild power switch (fps tm )
fscm0565r 2 internal block diagram figure 2. functional block diagram of fscm0565r 8v/12v 3 1 2 4 vref internal bias s q q r osc v cc v cc i delay i fb v sd tsd vovp v cc s q q r r 2.5r vcc good v cc drain fb gnd gate driver v cc good 0.3/0.5v leb pwm soft start + - 6 i_limit freq. modulation v cc uv reset 0.3k 5 n.c.
fscm0565r 3 pin definitions pin configuration figure 3. pin configuration (top view) pin number pin name pin function description 1drain this pin is the high voltage power sensef et drain. it is designed to drive the transformer directly. 2 gnd this pin is the control ground and the sensefet source. 3v cc this pin is the positive supply voltage input. initially, during start up, the power is supplied through the startup resistor fr om dc link. when vcc reaches 12v, the power is supplied from the auxiliary transformer winding. 4 feedback (fb) this pin is internally connected to the inverting input of the pwm comparator. the collector of an optocoupler is typically tied to this pin. for stable operation, a capacitor should be placed between this pin and gnd. if the voltage of this pin reaches 6.0v, the over load protection is activated resulting in shutdown of the fps. 5n.c. this pin is not connected. 6i limit this pin is for the pulse by pulse current limit level programming. by using a resistor to gnd on this pin, the current limit level can be changed. if this pin is left floating, the typical current limit will be 2.5a. fscm0565rj 1 : drain 2 : gnd 6 : i_limit 4 : fb 3 : vcc 5 : n.c. d2-pak-6l fscm0565rg 1. drain 2. gnd 3. vcc 4. fb 6. i_limit 5. n.c. to-220-6l fscm0565rj fscm0565rg i2-pak-6l fscm0565ri fscm0565ri 1 : drain 2 : gnd 6 : i_limit 4 : fb 3 : vcc 5 : n.c.
fscm0565r 4 absolute maximum ratings (ta=25 c, unless otherwise specified.) notes: 1. t j = 25 c to 150 c 2. repetitive rating: pulse width limi ted by maximum junction temperature . thermal impedance note: 1. free standing with no heat -sink under natural convection 2. infinite cooling condition - refer to the semi g30-88. parameter symbol value unit drain-source (gnd) voltage (1) v dss 650 v drain-gate voltage (r gs =1m )v dgr 650 v gate-source (gnd) voltage v gs 30 v drain current pulsed (2) i dm 20 a dc continuous drain current (d2-pak, i2-pak) @ tc = 25c i d 3.9 a dc @ tc =100 ci d 2.5 a dc continuous drain current (to-220) @ tc = 25c i d 5a dc @ tc =100 ci d 3.2 a dc supply voltage v cc 20 v analog input voltage range v fb -0.3 to v cc v total power dissipation (d2-pak,i2-pak) p d 75 w total power dissipation (to-220) p d 120 w operating junction temperature t j internally limited c operating ambient temperature t a -25 to +85 c storage temperature range t stg -55 to +150 c esd capability, hbm model (all pins except vfb) - 2.0 (gnd-vfb = 1.5kv) (vcc-vfb = 1.0kv) kv esd capability, machine model (all pins except vfb) - 300 (gnd-vfb = 250v) (vcc-vfb = 100v) v parameter symbol value unit junction-to-ambient thermal ja (1) - c/w junction-to-case thermal (d2-pak, i2-pak) jc (2) 1.7 c/w junction-to-case thermal (to-220) jc (2) 1.0 c/w
fscm0565r 5 electrical characteristics (ta = 25 c unless otherwise specified.) notes: 1. pulse test: pulse width 300 s, duty 2% 2. these parameters, although guaranteed at the design, are not tested in mass production. parameter symbol condition min. typ. max. unit sensefet section drain source breakdown voltage bv dss v gs = 0v, i d = 250 a 650 - - v zero-gate-voltage current i dss v ds = max, rating v gs = 0v - - 500 a static drain source on resistance (1) r ds(on) v gs = 10v, i d = 2.3a - 1.76 2.2 output capacitance c oss v gs = 0v, v ds = 25v, f = 1mhz -78 -pf turn on delay time t d(on) v dd = 325v, i d = 5a (mosfet switching time is essentially independent of operating temperature) -22 - ns rise time t r -52 - turn off delay time t d(off) -95 - fall time t f -50 - control section initial frequency f osc v cc = 14v, v fb = 5v 60 66 72 khz modulated frequency range f mod --3-khz frequency modulation cycle t mod --4-ms voltage stability f stable 10v v cc 17v 0 1 3 % temperature stability (2) f osc ? 25 c ta +85 c - 5 10 % maximum duty cycle d max -758085% minimum duty cycle d min ---0% start threshold voltage v start v fb = gnd 11 12 13 v stop threshold voltage v stop v fb = gnd 7 8 9 v feedback source current i fb v fb = gnd 0.7 0.9 1.1 ma soft-start time t ss -101520ms burst mode section burst mode voltages (2) v bh v cc =14v 0.4 0.5 0.6 v vb l v cc = 14v 0.24 0.3 0.36 v
fscm0565r 6 notes: 1. these parameters, although guaranteed at the design, are not tested in mass production. 2. these parameters indicate the inductor current. 3. this parameter is the current flowing into the control ic. protection section peak current limit (2) i lim v cc = 14v, v fb = 5v 2.2 2.5 2.8 a over voltage protection v ovp -181920v thermal shutdown temperature (1) t sd 130 145 160 c shutdowndelay current i delay v fb = 4v 3.5 5.3 7 a shutdown feedback voltage v sd v fb > 5.5v 5.5 6 6.5 v total device section startup current i start -2040 a operating supply current (3) i op(min) v cc = 10v, v fb = 0v -2.55ma i op(max) v cc = 20v, v fb = 0v
fscm0565r 7 comparison between fs dm0565rb and fscm0565r function fsdm0565rb fscm0565r frequency modulation n/a available ? modulated frequency range (df mod ) = 3khz ? frequency modulation cycle (t mod ) = 4ms pulse-by-pulse current limit ? internally fixed (2. 25a) ? programmable using external resistor (2.5a max) internal startup circuit ? available ? n/a (requires a startup resistor) ? startup current: 40ua (max)
fscm0565r 8 typical performance characteristics (these characteristic graphs are normalized at ta= 25 c.) figure 4. startup current vs. temp fi gure 7. start threshold voltage vs. temp figure 5 stop threshold voltage vs. temp figure 8. initial freqency vs. temp figure 6. maximum duty cycle vs. temp fi gure 9. feedback source current vs. temp 0.60 0.80 1.00 1.20 1.40 1.60 -50 -25 0 25 50 75 100 125 junction temperature ( ) start up current (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) start threshold voltage (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50 -25 0 25 50 75 100 125 junction temperature ( ) stop threshold voltage (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) initial frequency (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) maximum duty cycle (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) fb source current (normalized to 25 )
fscm0565r 9 typical performance characteristics (continued) (these characteristic graphs are normalized at ta= 25 c.) figure 10. shutdown feedback voltage vs. temp figure 13. shutdown delay current vs. temp figure 11. burst mode enable voltage vs. temp figure 14. burst mode disable voltage vs. temp figure 12. macimum drain current vs. temp fi gure 15. operating s upply current vs. temp 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction temperature ( ) shutdown fb voltag e (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) shutdown delay curren t (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) burst mode enable voltag e (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) burst mode disable voltag e (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) maximum drain current (normalized to 25 ) 0.80 0.88 0.96 1.04 1.12 1.20 -50-25 0 255075100125 junction t emperature ( ) operating supply curren t (normalized to 25 )
fscm0565r 10 functional description 1. startup : figure 16 shows the typical startup circuit and transformer auxiliary winding for the fscm0565r application. before the fscm0565r begins switching, it consumes only startup current (typically 25ua) and the current supplied from the dc link supply current consumed by the fps (icc), and charges the external capacitor (c a ) that is connected to the vcc pin. when vcc reaches start voltage of 12v (v start ), the fscm0565r begins switching, and the current consumed by the fscm0565r increases to 3ma. then, the fscm0565r continues its normal switching operation and the power required for this device is supplied from the transformer auxiliary winding, unless vcc drops below the stop voltage of 8v (v stop ). to guarantee the stable operation of the control ic, vcc has under voltage lockout (uvlo) with 4v hyst eresis. figure 17 shows the relation between the current consumed by the fps (i cc) and the supply voltage (v cc ) figure 16. startup circuit figure 17. relation between o perating supply c urrent and vcc voltage the minimum current supplied through the startup resistor is given by where v line min is the minimum input voltage, v start is the start voltage (12v) and r str is the startup resistor. the startup resistor should be chosen so that i sup min is larger than the maximum startup current (40ua). if not, v cc can not be charged to the start voltage and fps will fail to start up. 2. feedback control : the fscm0565r employs current mode control, as shown in figure 18. an opto-coupler (such as the h11a817a) and a shunt regulator (such as the ka431) are typically used to implement the feedback network. comparing the feedback voltage with the voltage across the rsense resistor makes it possible to control the switching duty cycle. when the reference pin voltage of the ka431 exceeds the internal reference voltage of 2.5v, the h11a817a led current increases, thus pulling down the feedback voltage and reducing the duty cycle. this event typically happens when the input voltage is increased or the output load is decreased. 2.1 pulse-by-pulse current limit : because current mode control is employed, the peak current through the sensefet is determined by the inverting input of the pwm comparator (vfb*) as shown in figure 18. when the current through the opto transistor is zero and the current limit pin (#5) is left floating, the feedback current source (i fb ) of 0.9ma flows only through the internal resistor (r+2.5r=2.8k). in this case, the cathode voltage of diode d2 and the peak drain current have maximum values of 2.5v and 2.5a, respec- tively. the pulse-by-pulse current limit can be adjusted using a resistor to gnd on the current limit pin (#5). the current limit level using an external resistor (r lim ) is given by figure 18. pulse width m odulation (pwm) circuit 2.2 leading edge blanking (leb) : at the instant the internal sensefet is turned on, there usually exists a high fscm0565r rstr v cc ca da i su p ac line (v line min - v line max ) c dc i cc i cc v cc vstop=8v 25ua 3ma vstart=12v vz power up power down i sup min 2v line min ? v start ? () 1 r str ----------- - ? = i lim r lim 2.5 a ? 2.8k r lim + ------------------------------------ = 4 osc vcc vref i delay i fb v sd r 2.5r gate driver olp d1 d2 + v fb * - vfb ka431 c b vo h11a817a r sense sensefet 6 r li m 0.9ma 0.3k
fscm0565r 11 current spike through the sensefet, caused by primary-side capacitance and secondary-side rectifier reverse recovery. excessive voltage across the rsense resistor can lead to incorrect feedback operation in the current mode pwm control. to counter this ef fect, the fscm0565r employs a leading edge blanking (leb) circuit. this circuit inhibits the pwm comparator for a short time (t leb ) after the sensefet is turned on. 3. protection circuit : the fscm0565r has several self protective functions such as over load protection (olp), over voltage protection (ovp) and thermal shutdown (tsd). because these protection circuits are fully integrated into the ic without external components, the reliability can be improved without increasing cost. once the fault condition occurs, switching is terminated and the sensefet remains off. this causes vcc to fall. when vcc reaches the uvlo stop voltage of 8v, the current consumed by the fscm0565r decreases to the startup current (typically 25ua) and the current supplied from the dc link charges the external capacitor (c a ) that is connected to the vcc pin. when vcc reaches the start voltage of 12v, the fscm0565r resumes its normal operation. in this manner, the auto-restart can alternately enable and disable the switching of the power sensefet until the fault condition is eliminated (see figure 19). figure 19. auto restart operation 3.1 over load protection (olp): overload is defined as the load current exceeding a pre-set level due to an unexpected event. in this situation, the protection circuit should be activated to protect the smps. however, even when the smps is in the normal operation, the over load protection circuit can be activated during the load transition. to avoid this undesired operation, the over load protection circuit is designed to be activated after a specified time to determine whether it is a transient situation or an overload situation. because of the pulse-by-pulse current limit capability, the maximum peak current through the sensefet is limited, and therefore the maximum input power is restricted with a given input voltage. if the output consumes beyond this maximum power, the output voltage (vo) decreases below the set voltage. this reduces the current through the opto-coupler led, which also reduces the opto- coupler transistor current, thus increasing the feedback voltage (vfb). if vfb exceeds 2.5v, d1 is blocked and the 5.3ua current source (i delay ) starts to charge c b slowly up to vcc. in this condition, vfb continues increasing until it reaches 6v, when the switching operation is terminated as shown in figure 20. the delay time for shutdown is the time required to charge c b from 2.5v to 6.0v with 5.3ua (i delay ). in general, a 10 ~ 50 ms delay time is typical for most applications. figure 20. over load protection 3.2 over voltage protection (ovp) : if the secondary side feedback circuit were to malfunction or a solder defect caused an open in the feedback path, the current through the opto-coupler transistor becomes almost zero. then, vfb climbs up in a similar manner to the over load situation, forcing the preset maximum current to be supplied to the smps until the over load protection is activated. because more energy than required is provided to the output, the output voltage may exceed the rated voltage before the over load protection is activated, resulting in the breakdown of the devices in the secondary side. to prevent this situation, an over voltage protection (ovp) circuit is employed. in general, vcc is proportional to the output voltage and the fscm0565r uses vcc instead of directly monitoring the output voltage. if v cc exceeds 19v, an ovp circuit is activated resulting in the termination of the switching operation. to avoid undesired activation of ovp during normal operation, vcc should be designed to be below 19v. 3.3 thermal shutdown (tsd): the sensefet and the fault situation 8v 12v vcc vds t fault occurs fault removed normal operation normal operation power on v fb t 2.5v 6.0v over load protection t 12 = cfb*(6.0-2.5)/i delay t 1 t 2
fscm0565r 12 control ic are built in one package. this makes it easy for the control ic to detect the heat generation from the sensefet. when the temperature exceeds approximately 145 c, the thermal protection is triggered resulting in shutdown of the fps. 4. frequency modulation : emi reduction can be accomplished by modulating the switching frequency of a switched power supply. frequency modulation can reduce emi by spreading the energy over a wider frequency range than the band width measured by the emi test equipment. the amount of emi reduction is directly related to the depth of the reference frequency. as can be seen in figure 21, the frequency changes from 63khz to 69khz in 4ms. figure 21. frequency modulation 5. soft start : the fscm0565r has an internal soft start circuit that increases pwm comparator inverting input voltage together with the sens efet current slowly after it starts up. the typical soft start time is15ms. the pulse width to the power switching device is progressively increased to establish the correct working conditions for transformers, rectifier diodes and capacitors. the voltage on the output capacitors is progressively in creased with the intention of smoothly establishing the required output voltage. preventing transformer saturation and reducing stress on the secondary diode during start up is also helpful. 6. burst operation: to minimize power dissipation in standby mode, the fscm0565r enters into burst mode operation at light load condition. as the load decreases, the feedback voltage decreases. as shown in figure 22, the device automatically enters into burst mode when the feedback voltage drops below vbl (300mv). at this point switching stops and the output voltages start to drop at a rate dependent on standby current load. this causes the feedback voltage to rise. once it passes vbh (500mv) , switching resumes. the feedback voltage then falls , and the process repeats. burst mode operation alternately enables and disables switching of the power sensefet , thereby reducing switching loss in standby mode. figure 22. waveforms of burst operation t s t s t s drain current f s 66khz 69khz 63khz 4ms t v fb vds 0.3v 0.5v ids vo vo set time switching disable d t1 t2 t3 switching di sable d t4
fscm0565r 13 typical application circuit features ? high efficiency (>81% at 85vac input) ? low standby mode power consumption (<1w at 240vac input and 0.4w load) ? low component count ? enhanced system reliability through various protection functions ? low emi through frequency modulation ? internal soft-start (15ms) key design notes ? resistors r102 and r105 are employed to prevent start-up at low input voltage ? the delay time for over load protection is designed to be a bout 50ms with c106 of 47nf. if a faster triggering of olp is required, c106 can be reduced to 22nf. 1. schematic figure 23. demo circuit application output power input vo ltage output voltage (max current) lcd monitor 40w universal input (85-265vac) 5v (2.0a) 12v (2.5a) 3 4 c102 220nf 275va c lf101 23mh c101 220nf 275va c rt1 5d-9 f1 fuse 250v 2a c103 100uf 400v r103 56k ? 2w c104 2.2nf 1kv d101 uf 4007 c106 47nf 50v c105 22uf 50v d102 tvr10g r104 5 ? 1 2 3 4 5 t1 eer3016 bd101 2kbp06m3n257 1 2 r101 560k ? 1w fscm0565r i limit vf b vcc drain gnd 1 2 3 4 6 zd10 1 22v 8 10 d202 mbrf10100 c201 1000uf 25v c202 1000u f 25v l20 1 12v, 2.5a 6 7 d201 mbrf1045 c203 1000uf 10v c204 1000u f 10v l20 2 5v, 2a r201 1k ? r202 1.2k ? r204 5.6k ? r203 10k ? c205 47nf r205 5.6k ? c301 4.7n f ic301 h11a817a ic201 ka431 r102 500k ? r105 500k ? r106 5k ? 1/4w 5 n.c
fscm0565r 14 2. transformer figure 24. transformer schematic diagram 3.winding specification 4.electrical characteristics 5. core & bobbin core: eer 3016 bobbin: eer3016 ae(mm2): 96 no pin (s f) wire turns winding method na 4 50.2 1 8 center winding insulation: polyester tape t = 0.050mm, 2layers np/2 2 10.4 1 18 solenoid winding insulation: polyester tape t = 0.050mm, 2layers n 12v 10 80.3 3 7 center winding insulation: polyester tape t = 0.050mm, 2layers n5v 7 60.3 3 3 center winding insulation: polyester tape t = 0.050mm, 2layers np/2 3 20.4 1 18 solenoid winding outer insulation: polyester tape t = 0.050mm, 2layers pin specification remarks inductance 1 - 3 520uh 10% 100khz, 1v leakage inductance 1 - 3 10uh max 2 nd all short eer3016 n p /2 n 12v n a 1 2 3 4 5 6 7 8 9 10 n p /2 n 5v
fscm0565r 15 6. demo circuit part list part value note part value note fuse c301 4.7nf polyester film cap. f101 2a/250v ntc inductor rt101 5d-9 l201 5uh wire 1.2mm resistor l202 5uh wire 1.2mm r101 560k 1w r102 500k 1/4w r103 56k 2w r104 5 1/4w diode r105 500k 1/4w d101 uf4007 r106 5k 1/4w d102 tvr10g r201 1k 1/4w d201 mbrf1045 r202 10k 1/4w d202 mbrf10100 r203 1.2k 1/4w r204 5.6k 1/4w r205 5.6k 1/4w bridge diode bd101 2kbp06m 3n257 bridge diode capacitor c101 220nf/275vac box capacitor line filter c102 220nf/275vac box capacitor lf101 23mh wire 0.4mm c103 100uf/400v electrolytic capacitor ic c104 10nf/1kv ceramic capacitor ic101 fscm0565r fps tm c105 22uf/50v electrolytic capacitor ic201 ka431(tl431) voltage reference c106 47nf/50v ceramic capacitor ic301 h11a817a opto-coupler c201 1000uf/25v electrolytic capacitor c202 1000uf/25v electrolytic capacitor c203 1000uf/10v electrolytic capacitor c204 1000uf/10v electrolytic capacitor c205 47nf/50v ceramic capacitor
fscm0565r 16 package dimensions d2-pak-6l notes: unless otherwise specified a) this package does not comply to any current packaging standard. b) all dimensions are in millimeters. c) dimensions are exclusive of burrs, mold flash, and tie bar extrusions. d) dimensions and tolerances per asme y14.5m-1994 5.10 4.70 9.40 9.00 (0.75) 2.19 1.27 3.81 1.75 1.40 1.00 10.10 9.70 1.40 1.25 4.70 4.30 0.70 0.50 min 9.50 min 9.00 10.00 min 4.00 min 0.85 2.19 1.27 1.75 b see detail a a (4.40) (8.58) (1.75) (0.90) (7.20) 15.60 15.00 r0.45 10.20 9.80 max1.10 max0.80
fscm0565r 17 package dimensions (continued) i2-pak-6l (forming)
fscm0565r 18 package dimensions (continued) dimensions in millimeters to-220-6l (forming) 0.60 0.45 (0.65) (7.15) (13.55) 2.19 1.27 3.81 1.75 1.40 1.25 (0.75) 15.90 15.50 max1.10 max0.80 10.20 9.80 r0.55 r0.55 0.70 0.50 8.30 7.30 9.40 9.00 3.48 2.88 2.60 2.20 23.80 23.20 20.00 19.00 4.70 4.30 2.90 2.70 10.10 9.70
fscm0565r 19 ordering information product number package marki ng code bvdss rds(on) max. fscm0565rj d2-pak-6l cm0565r 650v 2.2 fscm0565riwdtu i2-pak-6l fscm0565rgwdtu to-220-6l
fscm0565r 12/15/05 0.0m 001 ? 2005 fairchild semiconductor corporation life support policy fairchild?s products are not authorized for use as critical components in life support devices or systems without the express written approval of the president of fairchild semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain li fe, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com disclaimer fairchild semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. fairchild does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others.
careers | sitema go datasheets, samples, buy technical information applications design center support company investors my f a home >> find products >> fscm0565r recommend new device, fsq0565r general description back to top features contents ? general description ? features ? applications ? product status/pricing/packaging ? order samples ? application notes ? qualification support the fscm0565r is an integrated pulse width modulator (pwm) and sensefet specifically designed for high performance offline switch mode power supplies (smps) with minimal external components. this device is an integrated high voltage power switching regulator which combines an avalanche rugged sensefet with a current mode pwm control block. the pwm controller includes integrated fixed frequency oscillator, under voltage lockout, leading edge blanking (leb), optimized gate driver, internal soft start, temperature compensated precise sources for a loop compensation, and self protection circuitry. compared with a discrete mosfet and pwm controller solution, it can reduce to tal cost, comp onent count, size, and weight while si multaneously increasi ng efficiency, produ ctivity, and system reliability. this device is a basic platform well su ited for cost effective designs of flyback converters. z internal avalanche rugged sensefet z low start-up current (max 40a) z low power consumption under 1 w at 240vac and 0.4w load z precise fixed operating frequency (66khz) z frequency modulation for low emi z pulse by pulse current limiting (adjustable) z over voltage protection (ovp) z over load protection (olp) z thermal shutdown function (tsd) datasheet download this datasheet e - mail this datasheet this page print version related links request samples how to order products product change notices (pcns) support sales support quality and reliability design cente r pa g e 1 of 3 product folder - fairchil d p/n fscm0565r - recommend new device, fsq0565 r 17-au g -2007 mhtml:file://c:\temp\fscm0565rcydtu _ nl.mht
product status/pricing/packaging back to top application notes back to top back to top applications back to top z auto-restart mode z under voltage lock out (uvlo) with hysteresis z built-in soft start (15ms) z smps for vcr, svr, st b, dvd and dvcd z adaptor z smps for lcd monitor related application notes { an-4137: design guidelines for off-line flyback converters using fairchild power switch (fps) { an-4140: transformer design considerations for off-line flyback converters using fairchild power switch { an-4141: troubleshooting and design tips for fairchild power switch flyback applications { an-4148: audible noise reduction techniques for fps applications product product status pb-free status package type leads packing method package marking convention** fscm0565rcydtu_nl not recommended for new designs to-220 5 rail line 1: $y (fairchild logo) & z (asm. plant code) &e& 3 (3-digit date code) line 2: cm0565r indicates product with pb -free second-level interconne ct. for more information click here. package marking information for product fscm0565r is available. click here for more information . a n - 4148: audible noise reduction techniques for fps applications (215 k) jul 27, 2007 pa g e 2 of 3 product folder - fairchil d p/n fscm0565r - recommend new device, fsq0565 r 17-au g -2007 mhtml:file://c:\temp\fscm0565rcydtu _ nl.mht
qualification support click on a product for detailed qualification data back to top product fscm0565rcydtu_nl ? 2007 fairchild semiconductor products | design center | support | company news | investors | my fairchild | contact us | site index | privacy policy | site terms & conditions | standard terms & conditions o pa g e 3 of 3 product folder - fairchil d p/n fscm0565r - recommend new device, fsq0565 r 17-au g -2007 mhtml:file://c:\temp\fscm0565rcydtu _ nl.mht


▲Up To Search▲   

 
Price & Availability of FSCM0565RCYDTUNL

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X