tn specifications slim polarized relay tn relays 5.6 .220 14 .551 9.8 .386 mm inch rohs directive compatibility information http://www.nais-e.com/ features small header area makes higher density mounting possible high sensitivity: 140 mw nominal operating power (single side stable 3-12 v type) surge voltage withstand: 1500 v fcc part 68 self-clinching terminal also available contact note: #1 this value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. (sx relays are available for low level load switching [10v dc, 10ma max. level]) characteristics arrangement 2 form c initial contact resistance, max. (by voltage drop 6 v dc 1a) 60 m ? contact material gold-clad silver rating nominal switching capacity (resistive load) 1 a 30 v dc, 0.5 a 125 v ac max. switching power (resistive load) 30 w, 62.5 va max. switching voltage 110 v dc,125 v ac max. switching current 1 a min. switching capacity (reference value) #1 10 a 10 mv dc nominal operating power single side stable 140 mw (3 to 12 v dc) 200 mw (24 v dc) 300 mw (48 v dc) 1 coil latching 100 mw (3 to 12 v dc) 150 mw (24 v dc) 2 coil latching 200 mw (3 to 12 v dc) 300 mw (24 v dc) expected life (min. operations) mechanical (at 180 cpm) 10 8 electrical (at 20 cpm) 1 a 30 v dc resistive load 2 10 5 0.5 a 125 v ac resistive load 10 5 initial insulation resistance* 1 min. 1,000 m ? (at 500 v dc) initial breakdown voltage between open contacts 750 vrms for 1 min. (detection current: 10 ma) between contact and coil 1,000 vrms for 1 min. (detection current: 10 ma) between contact sets 1,000 vrms for 1 min. (detection current: 10 ma) fcc surge voltage between open contacts 1,500 v temperature rise* 2 (at 20 c) max. 50 c operate time [set time]* 3 (at 20 c) max. 3 ms [max. 3 ms] release time [reset time]* 4 (at 20 c) max. 3 ms [max. 3 ms] shock resistance functional* 5 min. 490 m/s 2 {50g} destructive* 6 min. 980 m/s 2 {100g} vibration resistance functional* 7 176.4 m/s 2 {18g}, 10 to 55 hz at double amplitude of 3 mm destructive 294 m/s 2 {30g}, 10 to 55 hz at double amplitude of 5 mm conditions for operation, transport and storage* 8 (not freezing and condensing at low temperature) ambient temperature ?0 c to +70 c ?0 f to +158 f humidity 5 to 85% r.h. unit weight approx. 1.5 g . 053 oz remarks * speci?ations will vary with foreign standards certi?ation ratings. * 1 measurement at same location as "initial breakdown voltage" section. * 2 by resistive method, nominal voltage applied to the coil; contact carrying current: 1 a. * 3 nominal voltage applied to the coil, excluding contact bounce time. * 4 nominal voltage applied to the coil, excluding contact bounce time without diode. * 5 half-wave pulse of sine wave: 11 ms; detection time: 10 s. * 6 half-wave pulse of sine wave: 6 ms. * 7 detection time: 10 s. * 8 refer to 6. conditions for operation, transport and storage mentioned in ambient envi r onment . all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
tn ordering information types and coil data (at 20 c 68 f ) 1. single side stable 2. 1 coil latching 3. 2 coil latching notes: 1. speci?d value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. 2. standard packing: tube: 50 pcs.; case: 1,000 pcs. 3. in case of 5 v drive circuit, it is recommended to use 4.5 v type relay. 4. agpd stationary contact types available for high resistance against contact sticking. when ordering, please add suf? "?" l ike tn2-12v-3. part no. nominal voltage, v dc pick-up voltage, v dc (max.) drop-out voltage, v dc (min.) nominal operating current, ma ( 10%) coil resistance, ? ( 10%) nominal operating power, mw max. allowable voltage, v dc standard pc board terminal self-clinching terminal tn2-3 v tn2-h-3 v 3 2.25 0.3 46.7 64.3 140 4.5 tn2-4.5 v tn2-h-4.5 v 4.5 3.38 0.45 31.1 145 140 6.7 tn2-5 v tn2-h-5 v 5 3.75 0.5 28.1 178 140 7.5 tn2-6 v tn2-h-6 v 6 4.5 0.6 23.3 257 140 9 tn2-9 v tn2-h-9 v 9 6.75 0.9 15.5 579 140 13.5 tn2-12 v tn2-h-12 v 1 2 9 1.2 11.7 1,028 140 18 tn2-24 v tn2-h-24 v 2 4 1 8 2.4 8.3 2,880 200 36 tn2-48 v tn2-h-48 v 4 8 3 6 4.8 6.25 7,680 300 57.6 part no. nominal voltage, v dc set voltage, v dc (max.) reset voltage, v dc (max.) nominal operating current, ma ( 10%) coil resistance, ? ( 10%) nominal operating power, mw max. allowable voltage, v dc standard pc board terminal self-clinching terminal tn2-l-3 v tn2-l-h-3 v 3 2.25 2.25 33.3 90 100 4.5 tn2-l-4.5 v tn2-l-h-4.5 v 4.5 3.38 3.38 22.2 202.5 100 6.7 tn2-l-5 v tn2-l-h-5 v 5 3.75 3.75 20 250 100 7.5 tn2-l-6 v tn2-l-h-6 v 6 4.5 4.5 16.7 360 100 9 tn2-l-9 v tn2-l-h-9 v 9 6.75 6.75 11.1 810 100 13.5 tn2-l-12 v tn2-l-h-12 v 1 2 9 9 8.3 1,440 100 18 tn2-l-24 v tn2-l-h-24 v 2 4 1 8 1 8 6.3 3,840 150 36 part no. nominal voltage, v dc set voltage, v dc (max.) reset voltage, v dc (max.) nominal operating current, ma ( 10%) coil resistance, ? ( 10%) nominal operating power, mw max. allowable voltage, v dc standard pc board terminal self-clinching terminal tn2-l2-3 v tn2-l2-h-3 v 3 2.25 2.25 66.7 45 200 4.5 tn2-l2-4.5 v tn2-l2-h-4.5 v 4.5 3.38 3.38 44.4 101.2 200 6.7 tn2-l2-5 v tn2-l2-h-5 v 5 3.75 3.75 40 125 200 7.5 tn2-l2-6 v tn2-l2-h-6 v 6 4.5 4.5 33.3 180 200 9 tn2-l2-9 v tn2-l2-h-9 v 9 6.75 6.75 22.2 405 200 13.5 tn2-l2-12 v tn2-l2-h-12 v 1 2 9 9 16.7 720 200 18 tn2-l2-24 v tn2-l2-h-24 v 2 4 1 8 1 8 12.5 1,920 300 28.8 ex. tn 2 l 2 h 12v contact arrangement operating function terminal shape coil voltage(dc) 2: 2 form c nil: standard pc board terminal h: self-clinching terminal nil: single side stable l: 1 coil latching l2: 2 coil latching 3,4.5,5,6,9,12, 24,48*v *48 v coil type: single side stable only note: agpd stationary contact types available for high resistance against contact sticking. when ordering, please add suffix 3?like tn2?2v?. all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
tn dimensions mm inch reference data standard pc board terminal self-clinching terminal general tolerance: 0.3 .012 3.5 .138 2.54 .100 0.5 .020 0.25 .010 1.385 .055 2.54 .100 14 551 9.8 9.5 .386 .374 5.6 .220 3.5 .138 2.54 .100 0.5 .020 0.25 .010 1.385 .055 2.54 .100 14 551 9.8 9.5 .386 .374 5.6 .220 pc board pattern (copper-side view) 2.54 .100 10.16 .400 2.54 .100 10-1.0 dia. hole 10-.039 dia. hole tolerance: 0.1 .004 schematic (bottom view) ?single side stable (deenergized condition) ?1-coil latching (reset condition) ?2-coil latching (reset condition) direction indication* 10 9 8 7 6 1 2 3 4 5 direction indication* 10 9 8 7 6 1 2 3 4 5 direction indication* 10 9 8 7 6 1 2 3 4 5 *orientation stripe located on top of relay 1. maximum switching capacity 2. life curve 3. mechanical life tested sample: tn2-12v, 10 pcs. 30 100 200 1.0 0.5 0.4 0.3 0.2 switching voltage,v switching current, a dc load (cos ? =1) ac load (cos ? =1) 100 10 0 0.5 1.0 switching current, a no. of operations, 10 4 125 v ac resistive load 30 v dc resistive load 10 100 1,000 10,000 0 10 20 30 40 50 60 70 80 90 100 ratio against the rated voltage, %v no. of operations, 10 4 max. max. min. min. pick-up voltage drop-out voltage 4. electrical life (dc load) tested sample: tn2-12v, 10 pcs. condition: 1 a 30 v dc resistive load, 20 cpm change of pick-up and drop-out voltage change of contact resistance 5. coil temperature rise tested sample: tn2-12v point measured: inside the coil ambient temperature: room temperature (25 to 26 c), 70 c (77 to 79 f), 158 f max. max. min. min. no. of operations, 10 4 0 10 20 30 40 50 60 70 80 90 100 5101 520 ratio against the rated voltage %v pick-up voltage drop-out voltage 5101520 no.of operations, 10 4 contact resistance,m ? 0 10 20 30 40 50 60 70 80 90 100 terminal no.2?? terminal no.7?? 0 coil applied voltage, %v temperature rise, c 80 90 100 110 120 130 140 150 10 20 30 40 50 60 70 carrying current 0 a (room temp.) 1 a (room temp.) 0 a (70 c) 1 a (70 c) all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
tn 6. operate/release time characteristics tested sample: tn2-12v, 5 pcs. 7. set/reset time characteristics tested sample: tn2-l2-12v, 5 pcs. 8. distribution of pick-up and drop-out voltages tested sample: tn2-12v, 40 pcs. max. min. min. 0 1 2 3 4 5 6 80 90 100 110 120 coil applied voltage, %v operate and release time, ms operate time release time max. max. min. 0 1 2 3 4 5 6 80 90 100 110 120 coil applied voltage, %v set and reset time, ms set time reset time ratio against the rated voltage, %v quantity 20 30 10 10 0203 0405060708090100 pick-up voltage drop-out voltage 9. distribution of set and reset voltage tested sample: tn2-l2-12v, 32 pcs. 10. ambient temperature characteristics tested sample: tn2-12v, 5 pcs. 11. distribution of contact resistance tested sample: tn2-12v, 38 pcs. (38 4 contacts) ratio against the rated voltage, %v quantity 20 30 10 0102 030405060708090100 set voltage reset voltage 20 0 x x pick-up voltage 40 60 80 e10e20e40 10 20 30 40 drop-out voltage ambient temperature, c ?0 ?0 ?0 ?0 variation ratio, % contact resistance,m ? quantity 10 20 30 40 0304050 terminal no. 2,3,4 side terminal no. 7,8,9 side 6 7 8 9 10 1 2 3 4 5 12-(1). malfunctional shock (single side stable) tested sample: tn2-12v, 6 pcs. 12-(2). malfunctional shock (latching) tested sample: tn2-l2-12v, 6 pcs. y z , z x , x , x x z z , y y , 980m/s 2 980m/s 2 980m/s 2 980m/s 2 980m/s 2 980m/s 2 y , deenergized condition energized condition y z , z x , x , x x z z , y y , 980m/s 2 980m/s 2 980m/s 2 980m/s 2 980m/s 2 980m/s 2 y , deenergized condition energized condition 13-(1). in?ence of adjacent mounting 13-(2). in?ence of adjacent mounting on on on off off off inter-relay distance , mm inch rate of change, % rate of change, % 05 .197 ?0 10 0 ?0 0 10 pick-up voltage drop-out voltage on on on off off off inter-relay distance , mm inch rate of change, % rate of change, % 05 .197 0 20 10 ?0 0 10 pick-up voltage drop-out voltage all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
tn for cautions f or us e , see rel a y t e c hnical in f ormation. 14. actual load test (35 ma 48 v dc wire spring relay load) circuit change of pick-up and drop-out voltage change of contact resistance 500 ? 500 ? 0.1 f 0.1 f 48 v dc 3 2 wire spring relay circuit diagram no. of operations, 10 4 ratio against the rated voltage, %v max. min. max. min. 010 10 20 30 40 50 60 70 80 90 100 20 30 40 50 pick-up voltage drop-out voltage no. of operations, 10 4 max. min. 010 10 20 30 40 50 60 70 80 90 100 20 30 40 50 contact resistance, m ? terminal no. 2? 15-(1). high-frequency characteristics tested sample: tn2-xxv isolation characteristics 15-(2). high-frequency characteristics tested sample: tn2-xxv insertion loss characteristics 15-(3). high-frequency characteristics tested sample: tn2-xxv v. s . w .r. terminal no. 7?? terminal no. 2?? 50 100 10 100 1000 frequency, mhz isolation, db 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 insertion loss, db terminal no. 7?? terminal no. 2?? 10 100 1000 frequency, mhz v.s.w.r. 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 terminal no. 7-8-9 terminal no. 2-3-4 10 100 1000 frequency, mhz all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
|
