506 dimensions are shown for reference purposes only. dimensions are in inches over (millimeters) unless otherwise specified. specifications and availability subject to change. p&b catalog 1308242 issued 3-03 (pdf revised 8-06) www.tycoelectronics.com technical support: refer to inside back cover. operate data @ 25 c must operate voltage: 75% of nominal voltage or less. must release voltage: 10% of nominal voltage or more. operate time (including bounce): 15 ms, max. release time (including bounce): 15 ms, max. at or from nominal coil voltage t9a series dc coil 30 amp pc board or panel mount relay file e22575 file lr15734 contact ratings @ 25 c arrangements: 1 form a (spst-no), and 1 form c (spdt). material: silver-cadmium oxide. mechanical life: 10 million operations, typical. minimum contact load: 1a @ 5vdc or 12vac. initial contact resistance: 75 milliohms, max., @ min. rated current (switched). initial dielectric strength between open contacts: 1,500v rms. between contacts and coil: 2,500v rms. 6 kv surge using 1.2 s/50 s impulse wave or .5 s C 100khz ring wave initial insulation resistance between mutually insulated elements: 10 9 ohms, min., @ 500vdc, 25 c and 50% r.h. coil data @ 25 c voltage: 5 to 110vdc. nominal coil power: 1.0w, (approx.) and 900mw (approx.) versions. maximum coil power: 2.8 watt. maximum coil temperature (5) : class f: 155 c. duty cycle: continuous. nominal dc resistance nominal voltage 10% (ohms) current (ma) 5 27 185 6 40 150 99793 12 155 77 15 256 59 18 380 47 20 450 44 22 545 40 24 660 36 28 890 31 36 1,450 25 48 2,560 19 110 13,450 8 coil data - 900mw coil data - 1 watt nominal dc resistance nominal voltage 10% (ohms) current (ma) 525200 636167 981111 12 144 83 15 225 67 18 324 56 22 484 45 24 576 42 48 2,304 21 110 12,100 9 features ? up to 30 amp switching in spst and 20 amp in spdt arrangements. ? wash-tight (washable) (6) , plastic case available. ? meets ul 873 and ul 508 spacing C 1/8" through air, 1/4" over surface. ? load connections made via 1/4" q. c. terminals and safety wells accept insulated female q. c. terminals (mounting codes 2 & 5). ? ul class f insulation system standard. ? well suited for various industrial, commercial and residential applications. typical electrical load & life - 1 watt coil contact contact load type of load operations arrangement 1 30a @ 240vac ul general purpose 100,000 25a @ 240vac resistive heater 100,000 5 20a/10a @ 240vac ul general purpose 100,000 20a/10a @ 240vac ul resistive 100,000 20a/10a @ 28vdc resistive 100,000 ul 508/873 & csa contact ratings - 1 watt coil voltage load type n.o. contact n.c. contact 277vac tungsten * 5.4a C 277vac ballast 10a 3a 240vac motor 2 hp 1/2 hp 240vac resistive *? 25a 20a 240vac general purpose? 30a 15a 240vac lra/fla **?? 80a/30a 30a/12a 240vac pilot duty * 470va 275va 125vac motor 1 hp 1/4 hp 120vac lra/fla 98a/22a C 120vac tungsten * 8.3a C 120vac pilot duty 470va C 28vdc resistive 20a 10a * rated 6,000 operations. ** higher ul & csa ratings available. ? for form c application, derate current to 20a (n.o.), 10a (n.c.). ?? for form c application, derate current to 67%. note: consult factory for other 900mw version contact ratings. contact ratings @ 25 c (unless otherwise noted) with relay properly vented. remove vent nib after soldering and cleaning. users should thoroughly review the technical data before selecting a product part number. it is recommended that user also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application. ul 508/873 & csa contact ratings - 900mw coil voltage load type n.o. contact n.c. contact operations 240vac general purpose 30a C 100,000 240vac resistive 18a C 100,000 @ 105 c 240vac resistive C 15a 6,000 240vac lra/fla 30a/15a C 100,000 120vac lra/fla 50a/16a C 100,000 120vac lra/fla 30a/11a C 200,000 note: consult factory for other 900mw version contact ratings.
507 dimensions are shown for reference purposes only. dimensions are in inches over (millimeters) unless otherwise specified. specifications and availability subject to change. www.tycoelectronics.com technical support: refer to inside back cover. p&b catalog 1308242 issued 3-03 (pdf revised 8-06) mechanical data termination: printed circuit and quick connect terminals (4) . enclosures (all have 94v-0 flammability rating): t9ap: dust protected plastic case t9as: wash-tight plastic case (washable) (2 & 3) . t9av: flux-proof plastic case. weight: q.c. version: 1.2 oz. (33g) approx. (mounting code 2 & 5). wash-tight model t9as: 0.9 oz. (26g) approx. (mounting code 1). notes (1) operating ambient temperature must consider must operate voltage change over temperature, contact temperature rise, coil temperature rise (if coil is not allowed to cool) and maximum coil temperature. specification ambient considers 20a load with coil cooled to ambient. (2) wash-tight relay terminals should not be bent. (3) remove knock-off nib after cleaning process for optimum life of wash-tight relays. (4) maximum soldering temperature is 500 f for 4 seconds. (5) class f coils are ul systems approved for maximum coil temperature of 140 c, by change of resistance method. (6) see application note 13c265 for proper relay mounting, termination, cleaning and pc board conductor width. coil rise test performed with 30a pc board to maintain 20 c maximum rise @ 30a. t9ap1d52-9 t9ap1d52-12 t9ap5d52-12 t9ap5d52-24 t9as1d12-12 t9as1d12-18 t9as1d12-24 t9as1d12-48 t9as1d22-12 t9as1d22-24 our authorized distributors are more likely to maintain the following items in stock for immediate delivery. 0 20 40 60 80 100 120 140 180 160 140 120 100 80 60 0a 10a 20a 30a wash-tight relay, vented (note 3) pc terminals for coil & contacts applied coil voltage (% of rated voltage) max. alowable ambient temp. ( c) 40 60 80 100 120 140 180 160 140 120 100 80 60 dust protected relay, flange mount 0a 10a 20a 30a applied coil voltage (% of rated voltage) max. alowable ambient temp. ( c) 0 20 40 60 80 100 120 140 180 160 140 120 100 80 60 wash-tight relay, vented (note 3) ; load connections via q.c. terminals, pc mount 0a 10a 20a 30a applied coil voltage (% of rated voltage) max. alowable ambient temp. ( c) environmental data storage temperature range: -55 c to 130 c. operating temperature range (1) : -55 c to +85 c. vibration, operational: 0.065" (1.65mm) max. excursions from 10-55 hz. with no contact opening >100 s. shock, operational: 10g for 11 ms with no contact opening >100 s. shock, mechanical: 100g. ambient temperature vs. coil voltage - 1 watt coil data below are average values and should be verified in application. tests were conducted within a 2' (.6 m) cube (still air); at nominal coil power @ 25 c; with normally open contact loaded; and with 4' (1.22 m) long, #10 awg load wires. p.c. board relays were mounted to a 30a, single side p.c. board (6) . ordering information typical part number b t9a s 5 d 2 2 -12 1. basic series: t9a = low cost, printed circuit board/panel power relay. 2. enclosure: p = dust protected plastic case (mounting code 5). s = wash-tight (washable) plastic case with knock off nib (mounting codes 1 & 2). v = flux-proof plastic case (mounting code 1). 3. contact arrangement: 1 = 1 form a (spst-no). 5 = 1 form c (spdt). 4. coil input: d = dc voltage (1 watt) l = dc voltage (900mw) 5. mounting & termination: 1 = printed circuit board mounting; pc terminals for coil & contacts (a) . 2 = printed circuit board mounting; pc terminals for coil & contacts, and .250" (6.35mm) quick connects for contacts (b) . 5 = flanged mounting; .187" (4.75mm) quick connects for coil and .250" (6.35mm) quick connects for contacts (c) . 6. contact material: 2 = silver-cadmium oxide. 7. coil voltage: 5 = 5vdc 9 = 9vdc 15 = 15vdc 20 = 20vdc 24 = 24vdc 36 = 36vdc 110 = 110vdc 6 = 6vdc 12 = 12vdc 18 = 18vdc 22 = 22vdc 28 = 28vdc 48 = 48vdc a) only available with enclosure code s & v. b) only available with enclosure code s. c) only available with enclosure code p. note: all part numbers are rohs compliant. t9as5d12-12 t9as5d12-24 t9as5d22-12 t9as5d22-24 t9av1l22-24
508 dimensions are shown for reference purposes only. dimensions are in inches over (millimeters) unless otherwise specified. specifications and availability subject to change. p&b catalog 1308242 issued 3-03 (pdf revised 8-06) www.tycoelectronics.com technical support: refer to inside back cover. t9as/v C mounting & termination code 1 .300 (7.62) .100 (2.54) .150 (3.81) .500 (12.7) .550 (13.97) .700 (17.78) .043 .003 dia. (1.09 .08) .081 .005 dia. (2.06 .13) .600 (15.24) .212 max. (5.38) .078 .003 dia. (1.98 .08) pc board layouts (bottom views) t9ap/s C mounting & termination code 2 .140 max. (3.56) .250 max. (6.35) .300 (7.62) .100 (2.54) .150 (3.81) .500 (12.7) .550 (13.97) .700 (17.78) .043 .003 dia. (1.09 .08) .081 .005 dia. (2.06 .13) .600 (15.24) .078 .003 dia. (1.98 .08) t9as/v C mounting & termination code 1 outline dimensions t9ap C mounting & termination code 5 wiring diagrams (bottom views) 1 form a t9as C mounting & termination code 2 1 form c .187 x .020 (4.75 x .508) quick connect 1.080 max. (27.43) 1.980 max. (50.29) 1.713 .010 (43.51 .25) .071 (1.80) rad. for #6 screw 1.280 max. (32.51) 1.100 max. (27.94) .250 x .032 (6.35 x .81) quick connect n c n o c o m note: recommended mounting screw torque is 4.0-5.0 lbs.in when #6 screw is used. .032 x .062 (.81 x 1.57) .045 x .045 (1.14 x 1.14) .03 (.80) 2 places .250 x .032 quick (6.35 x .81) connect nc no com 1.280 max. (32.51) 1.080 max. (27.43) .130 .020 (3.30 .51) 1.100 max. (27.94) ? .032 x .062 (.8 x 1.6) terminals .212 max. (5.38) .10 max. (2.54) .045 x .045 (1.14 x 1.14) terminal .805 max. (20.4) .69 (17.6) 1.280 max. (32.51) 1.08 max. (27.43) .50 (12.8) .03 (.80) terminals .130 + .016 C .010 3.30 + .41 C.25 ( ) ? .016 (.43)
|
