4 bi-directional solid state relay c60 series optically isolated 0.5 to 2.5 a electrical specifications (25 c unless otherwise specified) part number relay description c60 solid state relay, terminals for through hole mount sc60 solid state relay, terminals for surface mount input (control) specifications (see note 1) parameter min max units control voltage range (see figure 1) 1.1 1.5 vdc input current (see figure 1 and notes 1, 7) 50 ma input current (guaranteed on), (see figure 4 and note 7) 5.0 ma turn-off voltage (guaranteed off) 0.8 vdc reverse voltage protection -6 vdc output (load) specifications (see figure 2 and note 2) part number dc bi-directional parameter min max min max units load voltage rating c60-10 60 60 vdc C60-20 100 100 c60-30 200 200 c60-40 400 400 output current rating c60-10 2.5 1.25 adc C60-20 1.5 0.75 c60-30 1.0 0.50 c60-40 0.5 0.25 on resistance (see note 6) c60-10 0.07 0.28 ohms C60-20 0.2 0.7 c60-30 0.45 1.8 c60-40 1.0 4.0 leakage current at maximum voltage 2.0 1.0 m adc turn-on time @ 10 ma (see figure 4 and note 7) c60-10 4.0 4.0 ms C60-20,-30,-40 3.0 3.0 turn-off time c60-10 4.0 4.0 ms C60-20,-30,-40 3.0 3.0 output capacitance c60-10 1000 500 pf C60-20 500 250 c60-30 400 200 c60-40 400 200 isolation (input to output) 10 9 10 9 ohms dielectric strength 1500 1500 vac capacitance (input to output) 3.0 3.0 pf junction temperature (t j ) 125 125 c features/benefits power fet output with very low on resistance - virtually no offset with very low leakage and voltage drop. optical isolation - isolates control elements from load transients. eliminates ground loops and signal ground noise. three terminal output - output fets can be paralleled externally to change current load rating. floating output - allows for high and low side switching. switches high voltages and currents - voltages to 400 vdc. current to 2.5 adc. bi-directional, dc, or ac. high noise immunity - control circuit cannot be triggered by output switching noise. 6 pin mini-dip package - standard or surface mount available. description the c60 series solid state relay is an advanced design capable of switching very heavy loads in a physically small 6 pin mini dip package. these relays have a power fet output that ensures low on resistance, no offset voltage and low leakage current. they are versatile and can be used to switch ac, bi- directional or dc loads. optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching bl oc k dia g ram 5 64 123 input output y t ?
3 characteristic curves c60 series control current vs. voltage 25 20 15 10 5 0.9 1.0 1.1 1.2 1.3 1.4 1.5 volts notes: 1. series resistor is required to limit input current to 50 ma maximum. 4. loads may be connected to positive or negative referenced power supplies. inductive loads must be diode suppressed. 5. continuous load current is rated under the conditions of still air and mounted on a printed circuit board. r on = r (25?c) x e 0.006 (t j - 25?c) 2. the input current is 10 ma for all tests unless otherwise speci?d. 3. the surge current is non repetitive for a maximum duration of 20 ms (see figure 3). 6. to calculate on resistance for a given junction temperature calculate the new r on using the equation shown below: 7. turn on time can be controlled with input control current. calculate a new turn-on time: t on =(t speci cation limit )(10 ma/i in ) mechanical specification + - + - a) bi-directional/ac configuration (see note 4) b) dc configuration (see note 4) r s r s load load load load 5 6 4 1 2 3 5 6 4 1 2 3 ac/ dc ac/ dc +dc - dc - 40?c 25?c 85?c current (ma) figure 1 5.0 4.0 3.0 2.0 1.0 0 510152025 c60 - 10 c60 - 20,-30,-40 turn on time (ms) input current (ma) typical turn-on time vs. input current figure 4 0 8. load voltage rating should be derated 10% at -40?c specifications are subject to change without notice ?1996 teledyne relays solid state products 1/96 wiring configurations 20.0 -20 40 10 70 junction temperature ?c 4.0 8.0 12.0 16.0 surge current vs. junction temperature surge current (a) figure 3 (see note 3) 0 85 55 25 -5 c60-10 C60-20 10.0 2.0 4.0 6.0 8.0 0 c60-40 c60-30 bi-directional dc -20 0 20 40 60 80 1.25 0.25 0.50 0.75 1.00 2.5 2.0 1.5 1.0 0.5 ambient temperature ?c bi-directional maximum load current vs. temperature 0 0 figure 2 100 output current (a) dc C60-20 c60-30 c60-40 c60-10 sc 60 - dimensions are shown in inches (millimeters) tolerances (unless otherwise speci?d) operating temperature range: -40 c to 85 c storage temperature range: -40 c to 100 c case: 6 pin dual in line, filled epoxy. weight: 1 gm. maximum 654 3 2 1 0.195 (4.95) 0.390 (9.91) 0.250 (6.35) date code 0.290 (7.37) surface mount land pattern 0.065 (1.65) min 0.025 (0.64) min 0.100 (2.54) 0.200 (5.08) 0.010 (0.25) 0.175 (4.45) 0.018 0.xx = 0.010 ( 0.25) 0.03 0.010 10 5 0.150 min 0.100 0.085 (2.16) 0.300 0.020 min (0.762) (0.76) (0.051) (2.54) (0.46) 0.xxx = 0.005 ( 0.13) c 60 - 0.200 5 64 123 pin 1 index (5.08) (0.25)
|
