View TDA3603P_6096822.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

d a t a sh eet product speci?cation supersedes data of 1995 oct 04 file under integrated circuits, ic01 1997 aug 15 integrated circuits tda3603 multiple voltage regulator with switch
1997 aug 15 2 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 features general one v p state controlled regulator (regulator 2) regulator 2, reset and ignition buffer operate during load dump and thermal shutdown one control pin for switching regulator 1 and the power switch supply voltage range of - 18 to +50 v (operating from 9.75 v) low reverse current of regulator 2 low quiescent current (when regulator 1, power switch and ignition input are switched off, standby) ignition input/output reset output high ripple rejection power switch. protections reverse polarity safe (down to - 18 v without high reverse current) able to withstand voltages up to 18 v at the outputs (supply line may be shortened) esd protected on all pins thermal protection load dump protection foldback current limit protection for regulators 1 and 2 delayed second current limit protection for the power switch the regulator outputs and the power switch are dc short-circuited safe to ground and v p . general description the tda3603 is a multiple output voltage regulator with a power switch, intended for use in car radios with or without a microcontroller. it contains one fixed voltage regulator with a foldback current protection (regulator 1) and one fixed voltage regulator (regulator 2), intended to supply a microcontroller, that also operates during load dump and thermal shutdown. there is a power switch with protections, operated by the enable input. the reset and ignition outputs can be used to interface by the microcontroller. the reset signal can be used to call up the microcontroller and the ignition output indicates ignition voltage available. the supply pin can withstand load dump pulses and negative supply voltages. regulator 2 will be switched on at a supply voltage >6.5 v and off at a voltage of regulator 2 <1.9 v. ordering information type number package name description version tda3603 sil9mpf plastic single in-line medium power package with ?n; 9 leads sot110-1 TDA3603P hdip18 plastic heat-dissipating dual in-line package; 18 leads sot398-1
1997 aug 15 3 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 quick reference data notes 1. minimum operating voltage, only if v p has exceeded 6.5 v. 2. the drop-out voltage of regulator 1 is measured between v p and reg1. 3. the drop-out voltage of the power switch is measured between v p and v sw . symbol parameter conditions min. typ. max. unit supply v p supply voltage operating 9.75 14.4 25 v regulator 2 on note 1 2.4 14.4 25 v jump start t 10 minutes -- 30 v load dump protection during 50 ms; t r 3 2.5 ms -- 50 v i q total quiescent current standby mode - 400 500 m a t vj operating virtual junction temperature -- 150 c voltage regulators v reg1 output voltage regulator 1 0.5 ma i reg1 300 ma 8.65 9.0 9.35 v v reg2 output voltage regulator 2 0.5 ma i reg2 50 ma; v p = 14.4 v 4.8 5.0 5.2 v v regd1 drop-out voltage regulator 1 i reg1 = 0.3 a; note 2 -- 0.5 v power switch v swd drop-out voltage i sw = 0.3 a; note 3 -- 0.9 v i m peak current t 10 ms 1.4 -- a
1997 aug 15 4 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 block diagram fig.1 block diagram (for sot110-1). handbook, full pagewidth mbe231 regulator 1 ignition buffer regulator 2 7 9 2 3 5 temperature load dump protection 1 8 4 6 power switch & & ground v p (14.4 v) v en tda3603 v i(ig) v o(ig) res (5 v) reg1 (9 v/300 ma) reg2 (5 v/50 ma) v sw (14.0 v/0.3 a)
1997 aug 15 5 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 pinning symbol pin description sot110-1 sot398-1 v p 1 1 supply voltage reg1 2 2 regulator 1 output res 3 3 reset output voltage (+5 v) v en 4 4 enable input voltage v o(ig) 5 5 ignition output voltage gnd 6 6 ground (0 v) reg2 7 7 regulator 2 output v i(ig) 8 8 ignition input voltage v sw 9 9 power switch output voltage i.c. - 10 to 18 can be connected to a heat spreader fig.2 pin configuration for sot110-1. handbook, halfpage tda3603 mbe230 1 2 3 4 5 6 7 8 9 v p reg1 reg2 res v o(ig) v i(ig) v sw gnd v en fig.3 pin configuration for sot398-1. pins 10 to 18 can be connected to a heat spreader. handbook, halfpage TDA3603P mbe229 1 2 3 4 5 6 7 8 9 18 17 16 15 14 13 12 11 10 v i.c. i.c. i.c. i.c. i.c. i.c. i.c. i.c. i.c. p reg1 reg2 res v o(ig) v i(ig) v sw gnd v en
1997 aug 15 6 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 functional description the tda3603 is a multiple output voltage regulator with a power switch, intended for use in car radios with or without a microcontroller. because of low-voltage operation of the car radio, low-voltage drop regulators are used. regulator 2 will switch on when the supply voltage exceeds 6.5 v for the first time and will switch off again when the output voltage of regulator 2 is below 1.9 v (this is below an engine start). when regulator 2 is switched on and the output voltage of this regulator is within its voltage range, the reset output will be enabled (reset will go high via a pull-up resistor) to generate a reset to the microcontroller. the reset cycles can be extended by an external capacitor at the reset output (pin 3). the start-up feature is built-in to ensure a smooth start-up of the microcontroller at first connection, without uncontrolled switching of regulator 2 during the start-up sequence. when both regulator 2 and the supply voltage (v p > 4.5 v) are available, regulator 1 and the switch can be operated by an enable input (pin 4). all output pins are fully protected. the regulators are protected against load dump (regulator 1 will switch off at supply voltages higher than 25 v) and short-circuit (foldback current protection). the switch contains a current protection which is delayed for 3 10 ms (in short-circuit condition). during this time the current is limited to 1.4 a (v p 18 v). at supply voltages over 16.9 v the switch is clamped at 15.0 v (to avoid externally connected circuitry being damaged by an overvoltage) and the switch will switch off at load dump. interfacing with the microcontroller can be accomplished by an ignition schmitt trigger and ignition output buffer, (simple full/semi on/off logic applications). the total timing of a semi on/off logic set is shown fig.4.
1997 aug 15 7 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 fig.4 timing diagrams. h andbook, full pagewidth mbe235 6.5 v 5.4 v 4.0 v 5.0 v 1.9 v 0 v 5.0 v 0 v 18.0 v 8.9 v 4.5 v 4.0 v 2.2 v 2.0 v 8.5 v 0 v 5.4 v 2.2 v 2.0 v 5.0 v 0.2 v 16.9 v 4.5 v 4.0 v 2.2 v 2.0 v 0 v load dump load dump load dump v p regulator 2 reset v p enable regulator 1 regulator 1 ignition input ignition output v p enable power switch power switch output
1997 aug 15 8 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 limiting values in accordance with the absolute maximum rating system (iec 134). thermal characteristics symbol parameter conditions min. max. unit v p supply voltage operating - 25 v jump start t 10 minutes - 30 v load dump protection during 50 ms; t r 3 2.5 ms - 50 v v p reverse battery voltage non-operating -- 18 v v ppi positive pulse voltage at ignition buffer v p = 14.4 v; r i =1k w- 50 v v npi negative pulse voltage at ignition buffer v p = 14.4 v; r i =1k w- - 100 v t stg storage temperature non-operating - 55 +150 c t vj operating virtual junction temperature - 40 +150 c p tot total power dissipation sot110-1 - 10.4 w sot398-1 - 8.3 w symbol type number parameter value unit r th j-c tda3603 thermal resistance from junction to case 12 k/w r th j-p TDA3603P thermal resistance from junction to pins 15 k/w
1997 aug 15 9 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 characteristics v p = 14.4 v; t amb =25 c; see fig.7; unless otherwise speci?ed. symbol parameter conditions min. typ. max. unit supply v p supply voltage operating 9.75 14.4 25 v regulator 2 on note 1 2.4 14.4 25 v jump start t 10 minutes -- 30 v load dump protection during 50 ms; t r 3 2.5 ms -- 50 v i q quiescent current v p = 12.4 v; note 2 - 400 500 m a v p = 14.4 v; note 2 - 420 -m a schmitt trigger power supply for the power switch v thr rising voltage threshold 4.0 4.5 5.0 v v thf falling voltage threshold 3.5 4.0 4.5 v v hys hysteresis - 0.5 - v schmitt trigger for regulator 1 v thr rising voltage threshold 4.0 4.5 5.0 v v thf falling voltage threshold 3.5 4.0 4.5 v v hys hysteresis - 0.5 - v schmitt trigger power supply for regulator 2 v thr rising voltage threshold 6.0 6.5 7.1 v v thf falling voltage threshold 1.7 1.9 2.2 v v hys hysteresis - 4.7 - v schmitt trigger for enable input v thr rising voltage threshold 1.7 2.2 2.7 v v thf falling voltage threshold 1.5 2.0 2.5 v v hys hysteresis - 0.2 - v schmitt trigger for reset buffer v r(reg2) rising voltage of regulator 2 note 3 - v reg2 - 0.15 - v v f(reg2) falling voltage of regulator 2 note 3 - v reg2 - 0.25 - v v spread voltage spread on tracking note 4 - 10 - mv schmitt trigger for ignition buffer v thr rising voltage threshold 1.7 2.2 2.7 v v thf falling voltage threshold 1.5 2.0 2.5 v v hys hysteresis - 0.2 - v reset buffer i sink low-level sink current v res 0.8 v 15 20 - ma i leak leakage current v p = 14.4 v; v res = 5 v 25 50 100 m a
1997 aug 15 10 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 ignition buffer v ol low-level output voltage i ol = 0 ma 0 0.2 0.8 v v oh high-level output voltage note 5 - 5.0 5.2 v i ol low-level output current v ol 0.8 v 0.3 0.8 - ma i oh high-level output current v oh 3 3 v 0.3 2.0 - ma regulator 1; note 6 v reg1 output voltage off - 1 400 mv v reg1 output voltage 0.5 ma i reg1 300 ma 8.65 9.0 9.35 v 10 v v p 18 v 8.65 9.0 9.35 v d v reg1 line regulation 10 v v p 18 v -- 50 mv d v regl1 load regulation 0.5 ma i reg1 300 ma -- 70 mv svrr1 supply voltage ripple rejection f i = 200 hz; v i = 2 v (p-p) 60 -- db v regd1 drop-out voltage i reg1 = 300 ma; note 7 - 0.4 0.5 v i regm1 current limit v reg1 > 7 v; note 8 0.45 - 1.2 a i regsc1 short-circuit current r l 0.5 w ; note 9 50 300 - ma a ct cross talk note 10 - 50 - db regulator 2; note 11 v reg2 output voltage 0.5 ma i reg2 50 ma 4.8 5.0 5.2 v 7v v p 18 v 4.8 5.0 5.2 v 18 v v p 50 v 4.75 5.0 5.25 v d v reg2 line regulation 7 v v p 18 v -- 50 mv d v regl2 load regulation 0.5 ma i reg1 30 ma -- 50 mv svrr2 supply voltage ripple rejection f i = 200 hz; v i = 2 v (p-p) 60 -- db v regd2 drop-out voltage i reg2 = 30 ma; note 12 - 0.3 0.4 v i regm2 current limit v reg2 > 4.5 v; note 8 0.1 - 0.5 a i regsc2 short-circuit current r l 0.5 w ; note 9 - 50 - ma a ct cross talk note 13 - 50 - db power switch v swd drop-out voltage i sw = 0.3 a; note 14 - 0.4 0.9 v i swcc continuous current 0.5 -- a v swcl clamping voltage v p 3 16.9 v - 15.0 16.2 v i m peak current t 10 ms 1.4 -- a v swfb ?y back voltage behaviour i sw = - 200 ma, v p =9v -- 20 v i lim(sw) current limit v p = 14.4 v; v sw < 1.5 v; note 8 0.6 - 1.0 a symbol parameter conditions min. typ. max. unit
1997 aug 15 11 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 notes to the characteristics 1. minimum operating voltage, only if v p has exceeded 6.5 v. 2. enable and ignition inputs are low and regulator 2 is unloaded. 3. voltage drop due to load condition. 4. the spread on tracking is one sigma value. 5. ignition output voltage will be less than or equal to the output voltage of regulator 2. 6. i reg1 = 5 ma. 7. the drop-out voltage of regulator 1 is measured between v p and reg1. 8. at current limit, i regm is held constant (see fig.5). 9. the foldback current protection limits the dissipated power at short-circuit (see figs 5 and 6). 10. the cross talk of regulator 1 is measured with an i reg2 = 0.5 ma up to 30 ma with an input frequency of f i = 100 khz. 11. i reg2 = 5 ma. 12. the drop-out voltage of regulator 2 is measured between v p and reg2. 13. the cross talk of regulator 2 is measured with an i reg1 = 0.5 ma up to 100 ma with an input frequency of f i = 100 khz. 14. the drop-out voltage of the power switch is measured between v p and v sw .
1997 aug 15 12 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 fig.5 foldback current protection of the regulators. handbook, halfpage 3 300 ma mgb755 9 v 2 v v reg1 i regsc1 i reg1 i regm1 handbook, halfpage 3 50 ma mgb756 5.0 v 1 v v reg2 i regsc2 i reg2 i regm2 a. regulator 1. b. regulator 2. fig.6 foldback current protection of the power switch. handbook, halfpage mbe234 1.4 10 1.4 0.5 t (ms) i sw (a)
1997 aug 15 13 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 test and application information fig.7 test circuit (for sot110-1). (1) capacitor not required for stability. n dbook, full pagewidth mbe232 regulator 2 regulator 1 enable input v ignition input reset output c3 10 m f v c2 10 m f c1 220 nf c4 10 m f c5 1 m f ignition output 47 k w r2 1 k w 5 v 8.5 v r l(sw) 1 k w r l(reg1) 1 k w r l(reg2) sw 9 7 2 3 5 8 4 1 6 tda3603 ground p v r1 1 k w p v en v i(ig) (1) noise information the noise at the output of the regulators depends on the bandwidth of the regulators, which can be adjusted by the output capacitors. table 1 shows the noise figures. although stability is guaranteed when c l is higher than 10 m f (over temperature range) with tan ( f ) = 1 in the frequency range 1 to 10 khz, however, for low noise, a 47 m f load capacitor is required. when electrolytic capacitors are used, the capacitor value will decrease and the esr will increase much at low temperatures. to avoid oscillation a normal capacitor of 220 nf can be placed in parallel with this electrolytic capacitor. the noise on the supply line depends on the value of the supply capacitor and is caused by a current noise (output noise of the regulators is translated into a current noise by the output capacitors). when a high frequency capacitor of 220 nf with an electrolytic capacitor of 100 m f in parallel is placed directly over pins 1 and 6 (supply and ground) the noise is minimized. table 1 noise ?gures note 1. bandwidth of 100 khz. regulator noise ( m v) (1) output capacitor ( m f) 1 180 10 100 47 80 100 2 120 10 70 47 70 100
1997 aug 15 14 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 short circuit behaviour of power switch the short circuit behaviour of the switch with large inductive loads (switch output goes out of the radio) can be improved by replacing c2 (see fig.7) by a larger electrolytic capacitor of 10 m f/16 v. when the temperature protection of the switch becomes active, due to a short circuit of the switch, the behaviour will be improved. when the switch is clamped an minimum output capacitor of 10 m f is needed. the power switch is not protected against loss of ground condition (= short of the switch to ground with floating ground pin of the tda3603 itself). a loss of ground situation can in practice only occur when the switch output goes outside the car-radio box. there is an application solution to protect against loss of ground (see fig.8). it is advisable to limit the dissipation at short circuit condition by monitoring the output of the power switch. the microprocessor can switch of the power switch when the switch was enabled and the switch output remains low due to a short circuit condition. fig.8 loss of ground protection. handbook, full pagewidth mgk595 v bat ( + ) v bat ( - ) v bat ( - ) tda3603 v p 1 6 gnd v sw d1 d2 c1 d3 switch output 9 short circuit to v bat ( - ) radio disconnected from v bat ( - )
1997 aug 15 15 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 package outlines unit a a max. 2 a 3 b 1 d 1 b 2 bcd (1) e (1) z max. (1) elpp 1 q 1 q 2 q references outline version european projection issue date iec jedec eiaj mm 18.5 17.8 3.7 8.7 8.0 a 4 15.8 15.4 1.40 1.14 0.67 0.50 1.40 1.14 0.48 0.38 21.8 21.4 21.4 20.7 6.48 6.20 3.4 3.2 2.54 1.0 5.9 5.7 4.4 4.2 3.9 3.4 15.1 14.9 q 1.75 1.55 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.25 mm maximum per side are not included. 2.75 2.50 sot110-1 92-11-17 95-02-25 0 5 10 mm scale 0.25 w d e a a c a 2 3 a 4 q 1 q 2 l q w m b b 1 b 2 d 1 p q 1 z e 19 p seating plane pin 1 index sil9mpf: plastic single in-line medium power package with fin; 9 leads sot110-1
1997 aug 15 16 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 unit a max. 12 b 1 (1) (1) (1) b 2 cd e e m z h l references outline version european projection issue date iec jedec eiaj mm dimensions (inch dimensions are derived from the original mm dimensions) sot398-1 94-04-13 95-01-25 a min. a max. b max. w m e e 1 1.40 1.14 0.67 0.50 0.47 0.38 21.85 21.35 6.5 6.2 3.9 3.1 0.25 2.54 7.62 8.32 8.02 8.7 7.7 1.0 4.7 0.51 3.7 inches 0.06 0.04 0.03 0.02 0.02 0.01 1.05 0.75 0.04 0.03 0.87 0.84 0.26 0.24 0.15 0.12 0.01 0.10 0.30 0.33 0.32 0.34 0.30 0.04 0.19 0.02 0.15 m h c (e ) 1 m e w m b 1 b 2 e a a 1 a 2 l seating plane z d e 18 1 10 9 b pin 1 index 0 5 10 mm scale note 1. plastic or metal protrusions of 0.25 mm maximum per side are not included. hdip18: plastic heat-dissipating dual in-line package; 18 leads sot398-1
1997 aug 15 17 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 soldering introduction there is no soldering method that is ideal for all ic packages. wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. however, wave soldering is not always suitable for surface mounted ics, or for printed-circuits with high population densities. in these situations reflow soldering is often used. this text gives a very brief insight to a complex technology. a more in-depth account of soldering ics can be found in our ic package databook (order code 9398 652 90011). soldering by dipping or by wave the maximum permissible temperature of the solder is 260 c; solder at this temperature must not be in contact with the joint for more than 5 seconds. the total contact time of successive solder waves must not exceed 5 seconds. the device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (t stg max ). if the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. repairing soldered joints apply a low voltage soldering iron (less than 24 v) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. if the temperature of the soldering iron bit is less than 300 c it may remain in contact for up to 10 seconds. if the bit temperature is between 300 and 400 c, contact may be up to 5 seconds. definitions life support applications these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips for any damages resulting from such improper use or sale. data sheet status objective speci?cation this data sheet contains target or goal speci?cations for product development. preliminary speci?cation this data sheet contains preliminary data; supplementary data may be published later. product speci?cation this data sheet contains ?nal product speci?cations. limiting values limiting values given are in accordance with the absolute maximum rating system (iec 134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the speci?cation is not implied. exposure to limiting values for extended periods may affect device reliability. application information where application information is given, it is advisory and does not form part of the speci?cation.
1997 aug 15 18 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 notes
1997 aug 15 19 philips semiconductors product speci?cation multiple voltage regulator with switch tda3603 notes
internet: http://www.semiconductors.philips.com philips semiconductors C a worldwide company ? philips electronics n.v. 1997 sca55 all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owne r. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reli able and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not con vey nor imply any license under patent- or other industrial or intellectual property rights. netherlands: postbus 90050, 5600 pb eindhoven, bldg. vb, tel. +31 40 27 82785, fax. +31 40 27 88399 new zealand: 2 wagener place, c.p.o. box 1041, auckland, tel. +64 9 849 4160, fax. +64 9 849 7811 norway: box 1, manglerud 0612, oslo, tel. +47 22 74 8000, fax. +47 22 74 8341 philippines: philips semiconductors philippines inc., 106 valero st. salcedo village, p.o. box 2108 mcc, makati, metro manila, tel. +63 2 816 6380, fax. +63 2 817 3474 poland: ul. lukiska 10, pl 04-123 warszawa, tel. +48 22 612 2831, fax. +48 22 612 2327 portugal: see spain romania: see italy russia: philips russia, ul. usatcheva 35a, 119048 moscow, tel. +7 095 755 6918, fax. +7 095 755 6919 singapore: lorong 1, toa payoh, singapore 1231, tel. +65 350 2538, fax. +65 251 6500 slovakia: see austria slovenia: see italy south africa: s.a. philips pty ltd., 195-215 main road martindale, 2092 johannesburg, p.o. box 7430 johannesburg 2000, tel. +27 11 470 5911, fax. +27 11 470 5494 south america: rua do rocio 220, 5th floor, suite 51, 04552-903 s?o paulo, s?o paulo - sp, brazil, tel. +55 11 821 2333, fax. +55 11 829 1849 spain: balmes 22, 08007 barcelona, tel. +34 3 301 6312, fax. +34 3 301 4107 sweden: kottbygatan 7, akalla, s-16485 stockholm, tel. +46 8 632 2000, fax. +46 8 632 2745 switzerland: allmendstrasse 140, ch-8027 zrich, tel. +41 1 488 2686, fax. +41 1 481 7730 taiwan: philips semiconductors, 6f, no. 96, chien kuo n. rd., sec. 1, taipei, taiwan tel. +886 2 2134 2865, fax. +886 2 2134 2874 thailand: philips electronics (thailand) ltd., 209/2 sanpavuth-bangna road prakanong, bangkok 10260, tel. +66 2 745 4090, fax. +66 2 398 0793 turkey: talatpasa cad. no. 5, 80640 gltepe/istanbul, tel. +90 212 279 2770, fax. +90 212 282 6707 ukraine : philips ukraine, 4 patrice lumumba str., building b, floor 7, 252042 kiev, tel. +380 44 264 2776, fax. +380 44 268 0461 united kingdom: philips semiconductors ltd., 276 bath road, hayes, middlesex ub3 5bx, tel. +44 181 730 5000, fax. +44 181 754 8421 united states: 811 east arques avenue, sunnyvale, ca 94088-3409, tel. +1 800 234 7381 uruguay: see south america vietnam: see singapore yugoslavia: philips, trg n. pasica 5/v, 11000 beograd, tel. +381 11 625 344, fax.+381 11 635 777 for all other countries apply to: philips semiconductors, marketing & sales communications, building be-p, p.o. box 218, 5600 md eindhoven, the netherlands, fax. +31 40 27 24825 argentina: see south america australia: 34 waterloo road, north ryde, nsw 2113, tel. +61 2 9805 4455, fax. +61 2 9805 4466 austria: computerstr. 6, a-1101 wien, p.o. box 213, tel. +43 160 1010, fax. +43 160 101 1210 belarus: hotel minsk business center, bld. 3, r. 1211, volodarski str. 6, 220050 minsk, tel. +375 172 200 733, fax. +375 172 200 773 belgium: see the netherlands brazil: see south america bulgaria: philips bulgaria ltd., energoproject, 15th floor, 51 james bourchier blvd., 1407 sofia, tel. +359 2 689 211, fax. +359 2 689 102 canada: philips semiconductors/components, tel. +1 800 234 7381 china/hong kong: 501 hong kong industrial technology centre, 72 tat chee avenue, kowloon tong, hong kong, tel. +852 2319 7888, fax. +852 2319 7700 colombia: see south america czech republic: see austria denmark: prags boulevard 80, pb 1919, dk-2300 copenhagen s, tel. +45 32 88 2636, fax. +45 31 57 0044 finland: sinikalliontie 3, fin-02630 espoo, tel. +358 9 615800, fax. +358 9 61580920 france: 4 rue du port-aux-vins, bp317, 92156 suresnes cedex, tel. +33 1 40 99 6161, fax. +33 1 40 99 6427 germany: hammerbrookstra?e 69, d-20097 hamburg, tel. +49 40 23 53 60, fax. +49 40 23 536 300 greece: no. 15, 25th march street, gr 17778 tavros/athens, tel. +30 1 4894 339/239, fax. +30 1 4814 240 hungary: see austria india: philips india ltd, band box building, 2nd floor, 254-d, dr. annie besant road, worli, mumbai 400 025, tel. +91 22 493 8541, fax. +91 22 493 0966 indonesia: see singapore ireland: newstead, clonskeagh, dublin 14, tel. +353 1 7640 000, fax. +353 1 7640 200 israel: rapac electronics, 7 kehilat saloniki st, po box 18053, tel aviv 61180, tel. +972 3 645 0444, fax. +972 3 649 1007 italy: philips semiconductors, piazza iv novembre 3, 20124 milano, tel. +39 2 6752 2531, fax. +39 2 6752 2557 japan: philips bldg 13-37, kohnan 2-chome, minato-ku, tokyo 108, tel. +81 3 3740 5130, fax. +81 3 3740 5077 korea: philips house, 260-199 itaewon-dong, yongsan-ku, seoul, tel. +82 2 709 1412, fax. +82 2 709 1415 malaysia: no. 76 jalan universiti, 46200 petaling jaya, selangor, tel. +60 3 750 5214, fax. +60 3 757 4880 mexico: 5900 gateway east, suite 200, el paso, texas 79905, tel. +9-5 800 234 7381 middle east: see italy printed in the netherlands 547027/1200/03/pp20 date of release: 1997 aug 15 document order number: 9397 750 02229

▲Up To Search▲

Price & Availability of TDA3603P

	To Download TDA3603P Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .