View CAT4240TD-GT3_6039989.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2010 february, 2010 ? rev. 3 1 publication order number: cat4240/d cat4240 6 watt boost led driver description the cat4240 is a dc/dc step ? up converter that delivers an accurate constant current ideal for driving leds. operation at a fixed switching frequency of 1 mhz allows the device to be used with small value external ceramic capacitors and inductor. leds connected in series are driven with a regulated current set by the external resistor r1. the cat4240 high ? voltage output stage is perfect for driving mid ? size and large panel displays containing up to ten white leds in series. led dimming can be done by using a dc voltage, a logic signal, or a pulse width modulation (pwm) signal. the shutdown input pin allows the device to be placed in power ? down mode with ?zero? quiescent current. in addition to thermal protection and overload current limiting, the device also enters a very low power operating mode during ?open led? fault conditions. the device is housed in a low profile (1 mm max height) 5 ? lead thin sot23 package for space critical applications. features ? switch current limit 750 ma ? drives high voltage led strings (38 v) ? up to 94% efficiency ? low quiescent ground current 0.6 ma ? 1 mhz fixed frequency low noise operation ? soft start ?in ? rush? current limiting ? shutdown current less than 1 a ? open led overvoltage protection ? automatic shutdown at 1.9 v (uvlo) ? thermal overload protection ? thin sot23 5 ? lead (1 mm max height) ? these devices are pb ? free, halogen free/bfr free and are rohs compliant applications ? gps navigation systems ? portable media players ? handheld devices, digital cameras figure 1. typical application circuit l1: sumida cdrh6d28 ? 470 d1: central cmsh1 ? 40 (rated 40 v) vin cat4240 l1 d1 vout r1 1 r2 300 ma (300 mv) 1 f 4.7 f/16 v 8 v to 16 v vin 5 v c1 c3 c2 fb gnd 47 h 1 f/50 v sw 1 k shdn v l http://onsemi.com tsot ? 23 td suffix case 419ae pin connections tgym marking diagram device package shipping ordering information cat4240td ? gt3 tsot ? 23 (pb ? free) green* 3,000/ tape & reel tg = specific device code y = production year (last digit) m = production month (1 ? 9, a, b, c) 1 5 (top view) vin shdn sw gnd fb 1 * nipdau plated finish
cat4240 http://onsemi.com 2 table 1. absolute maximum ratings parameters ratings units v in , fb voltage ? 0.3 to +7 v shdn voltage ? 0.3 to +7 v sw voltage ? 0.3 to 60 v storage temperature range ? 65 to +160 c junction temperature range ? 40 to +150 c lead temperature 300 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. table 2. recommended operating conditions parameters range units v in up to 5.5 v sw pin voltage 0 to 38 v ambient temperature range (note 1) ? 40 to +85 c note: typical application circuit with external components is shown on page 1. 1. thin sot23 ? 5 package thermal resistance ja = 135 c/w when mounted on board over a ground plane. table 3. dc electrical characteristics (v in = 3.6 v, ambient temperature of 25 c (over recommended operating conditions unless otherwise specified)) symbol parameter test conditions min typ max units i q operating current v fb = 0.2 v v fb = 0.4 v (not switching) 0.6 0.1 1.5 0.6 ma i sd shutdown current v shdn = 0 v 0.1 1 a v fb fb pin voltage 6 leds with i led = 75 ma 285 300 315 mv i fb fb pin input leakage 1 a i led programmed led current r1 = 10 r1 = 5 28.5 30 60 31.5 ma v ih v il shdn logic high shdn logic low enable threshold level shutdown threshold level 0.4 0.8 0.7 1.5 v f sw switching frequency 0.8 1.0 1.3 mhz dc maximum duty cycle v in = 3 v 92 % i lim switch current limit v in = 3.6 v v in = 5 v 600 750 ma r sw switch ?on? resistance i sw = 100 ma 1.0 2.0 i leak switch leakage current switch off, v sw = 30 v 2 5 a thermal shutdown 150 c thermal hysteresis 20 c v uvlo undervoltage lockout (uvlo) threshold 1.9 v v ov-sw overvoltage detection threshold 40 v v ocl output voltage clamp ?open led? 42 v
cat4240 http://onsemi.com 3 typical characteristics (v in = 5 v, v l = 13 v, t amb = 25 c, typical application circuit unless otherwise specified.) figure 2. quiescent current vs. v in (not switching) figure 3. quiescent current vs. v in (switching) input voltage (v) input voltage (v) 5.5 5.0 4.5 4.0 3.5 3.0 50 100 150 200 5.0 4.5 4.0 3.5 3.0 0 0.5 1.0 1.5 2.0 figure 4. fb pin voltage vs. temperature figure 5. fb pin voltage vs. output current temperature ( c) output current (ma) 150 100 50 0 ? 50 297 298 299 300 301 302 303 200 150 100 50 0 290 295 300 305 310 figure 6. switching frequency vs. supply voltage figure 7. switch on resistance vs. input voltage input voltage (v) 5.0 4.5 5.5 4.0 3.5 3.0 0.8 0.9 1.0 1.1 1.2 quiescent current ( a) quiescent current (ma) fb pin voltage (mv) fb pin voltage (mv) switching frequency (mhz) v fb = 0.4 v 4 leds 5.5 input voltage (v) 5.0 4.5 5.5 4.0 3.5 3.0 0 0.5 1.0 1.5 2.0 switch resistance ( )
cat4240 http://onsemi.com 4 typical characteristics (v in = 5 v, v l = 13 v, t amb = 25 c, typical application circuit unless otherwise specified.) figure 8. led current vs. input voltage figure 9. led current regulation inductor voltage (v) inductor voltage (v) 14 11 10 9 8 100 150 200 250 300 350 16 14 13 11 10 8 ? 1.0 ? 0.5 0 0.5 1.0 figure 10. efficiency vs. load current (6 leds) figure 11. efficiency vs. inductor voltage (6 leds) led current (ma) inductor voltage (v) 300 250 200 150 100 50 80 85 90 95 100 15 12 11 9 8 80 85 90 95 100 figure 12. power ? up with 6 leds at 300 ma figure 13. switching waveform led current (ma) led current variation (%) efficiency (%) efficiency (%) 6 leds @ 150 ma 16 rset = 1 vout = 19.5 v 14 rset = 2 vout = 18.8 v 12 13 15 ? 2.0 ? 1.5 1.5 2.0 10 13 16 91215
cat4240 http://onsemi.com 5 typical characteristics (v in = 5 v, v l = 13 v, t amb = 25 c, typical application circuit unless otherwise specified.) figure 14. maximum output current figure 15. shutdown voltage inductor voltage (v) input voltage (v) 16 14 10 9 8 100 200 300 400 500 5.0 4.5 4.0 3.5 3.0 0.2 0.4 0.6 0.8 1.0 max output current (ma) shutdown voltage (v) vout = 30 v ? 25 c ? 40 c 85 c 125 c 12 figure 16. switch current limit vout = 20 v input voltage (v) 5.5 5.0 4.0 3.5 3.0 700 800 900 1000 1100 1200 sw current limit (ma) 4.5 vout = 20 v 11 13 15 2.5
cat4240 http://onsemi.com 6 pin description vin is the supply input for the internal logic. the device is compatible with supply voltages down to 2.8 v and up to 5.5 v. it is recommended that a small bypass ceramic capacitor (4.7 f) be placed between the vin and gnd pins near the device. if the supply voltage drops below 1.9 v, the device stops switching. shdn is the shutdown logic input. when the pin is tied to a voltage lower than 0.4 v, the device is in shutdown mode, drawing nearly zero current. when the pin is connected to a voltage higher than 1.5 v, the device is enabled. gnd is the ground reference pin. this pin should be connected directly to the ground plane on the pcb. sw pin is connected to the drain of the internal cmos power switch of the boost converter. the inductor and the schottky diode anode should be connected to the sw pin. traces going to the sw pin should be as short as possible with minimum loop area. an over-voltage detection circuit is connected to the sw pin. when the voltage reaches 40 v, the device enters a low power operating mode preventing the sw voltage from exceeding the maximum rating. fb feedback pin is regulated at 0.3 v. a resistor connected between the fb pin and ground sets the led current according to the formula: i led 0.3 v r1 the lower led cathode is connected to the fb pin. table 4. pin descriptions pin # name function 1 sw switch pin. this is the drain of the internal power switch. 2 gnd ground pin. connect the pin to the ground plane. 3 fb feedback pin. connect to the last led cathode. 4 shdn shutdown pin (logic low). set high to enable the driver. 5 vin power supply input. simplified block diagram figure 17. simplified block diagram current sense ref 300 mv led current c1 thermal shutdown & uvlo 1 mhz oscillator over voltage protection pwm & logic driver c2 gnd sw fb r1 + ? + ? + ? v in v in shdn r s v out
cat4240 http://onsemi.com 7 device operation the cat4240 is a fixed frequency (1 mhz), low noise, inductive boost converter that provides a constant current with excellent line and load regulation. the device uses a high-voltage cmos power switch between the sw pin and ground to energize the inductor. when the switch is turned off, the stored energy in the inductor is released into the load via the schottky diode. the on/off duty cycle of the power switch is internally adjusted and controlled to maintain a constant regulated voltage of 0.3 v across the feedback resistor connected to the feedback pin (fb). the value of the resistor sets the led current accordingly (0.3 v/r 1 ). during the initial power ? up stage, the duty cycle of the internal power switch is limited to prevent excessive in ? rush currents and thereby provide a ?soft ? start? mode of operation. when the inductor is connected to a 9 v supply or higher, the cat4240 can drive 6 leds in series at 300 ma delivering a total power of 6 watts into the load. a separate 5 v supply voltage is connected to the vin pin. in the event of an ?open led? fault condition, where the feedback control loop becomes open, the output voltage will continue to increase. once this voltage exceeds 40 v, an internal protection circuit will become active and place the device into a very low power safe operating mode. thermal overload protection circuitry has been included to prevent the device from operating at unsafe junction temperatures above 150 c. in the event of a thermal overload condition the device will automatically shutdown and wait till the junction temperatures cools to 130 c before normal operation is resumed. application information external component selection capacitors the cat4240 only requires small ceramic capacitors of 4.7 f on the inductor input, 1 f on the vin pin and 1 f on the output. under normal condition, a 4.7 f input capacitor is sufficient. for applications with higher output power, a lar ger input capacitor of 10 f may be appropriate. x5r and x7r capacitor types are ideal due to their stability across temperature range. inductor a 47 h inductor is recommended for most of the cat4240 applications. in cases where the efficiency is critical, inductances with lower series resistance are preferred. i nductors with current rating of 800 ma or higher are recommended for most applications. sumida cdrh6d28 ? 470 47 h inductor has a rated current of 800 ma and a series resistance (d.c.r.) of 176 m typical. schottky diode the current rating of the schottky diode must exceed the peak current flowing through it. the schottky diode performance is rated in terms of its forward voltage at a given current. in order to achieve the best efficiency, this forward voltage should be as low as possible. the response time is also critical since the driver is operating at 1 mhz. central semiconductor schottky rectifier cmsh1 ? 40 (1 a rated) is recommended for most applications. led current setting the led current is set by the external resistor r1 connected between the feedback pin (fb) and ground. the formula below gives the relationship between the resistor and the current: r1 0.3 v led current table 5. resistor r1 and led current led current (ma) r1 ( ) 20 15 25 12 30 10 100 3 300 1
cat4240 http://onsemi.com 8 open led protection in the event of an ?open led? fault condition, the cat4240 will continue to boost the output voltage with maximum power until the output voltage reaches approximately 40 v. once the output exceeds this level, the internal circuitry immediately places the device into a very low power mode where the total input power is limited to about 6 mw (about 1.6 ma input current with a 3.6 v supply). the sw pin clamps at a voltage below its maximum rating of 60 v. there is no need to use an external zener diode between vout and the fb pin. a 50 v rated c 2 capacitor is required to prevent any overvoltage damage in the open led condition. figure 18. open led protection without zener vin cat4240 l schottky 100 v (central cmsh1 ? 100) r1 3 4.7 f 1 f fb sw gnd on off 47 h vin c1 vout shdn c2 5 v v l 13 v figure 19. open led supply current vs. v in without zener inductor voltage (v) 14 13 10 9 8 0 2.0 1.0 4.0 5.0 input current (ma) 16 3.0 figure 20. open led output voltage vs. v in without zener inductor voltage (v) 14 13 10 9 8 40 50 45 55 60 output voltage (v) 16 11 12 15 11 12 15 vin = 5 v figure 21. open led disconnect and reconnect figure 22. open led disconnect
cat4240 http://onsemi.com 9 dimming control there are several methods available to control the led brightness. pwm signal on the shdn pin led brightness dimming can be done by applying a pwm signal to the shdn input. the led current is repetitively turned on and off, so that the average current is proportional to the duty cycle. a 100% duty cycle, with shdn always high, corresponds to the leds at nominal current. figure 23 shows a 1 khz signal with a 50% duty cycle applied to the shdn pin. the recommended pwm frequency range is from 100 hz to 2 khz. figure 23. switching waveform with 1 khz pwm on shdn filtered pwm signal a filtered pwm signal used as a variable dc voltage can control the led current. figure 24 shows the pwm control circuitry connected to the cat4240 fb pin. the pwm signal has a voltage swing of 0 v to 2.5 v. the led current can be dimmed within a range from 0 ma to 20 ma. the pwm signal frequency can vary from very low frequency up to 100 khz. figure 24. circuit for filtered pwm signal 1 k 3.1 k 0 v 2.5 v 0.22 f c3 vin cat4240 fb sw gnd pwm signal led current rb 3.73 k shdn r1 15 r2 ra v fb = 300 mv v in a pwm signal at 0 v dc, or a 0% duty cycle, results in a max led current of about 22 ma. a pwm signal with a 93% duty cycle or more, results in an led current of 0 ma. figure 25. filtered pwm dimming (0 v to 2.5 v) led current (ma) 25 20 15 10 5 0 0 10 20 30 40 50 60 70 80 90 100 pwm duty cycle (%)
cat4240 http://onsemi.com 10 board layout the cat4240 is a high ? frequency switching regulator. the traces that carry the high ? frequency switching current have to be carefully laid out on the board in order to minimize emi, ripple and noise in general. the thicker lines on figure 26 show the switching current path. all these traces have to be short and wide enough to minimize the parasitic inductance and resistance. the loop shown on figure 26 corresponds to the current path when the cat4240 internal switch is closed. on figure 27 is shown the current loop, when the cat4240 switch is open. both loop areas should be as small as possible. capacitor c 1 has to be placed as close as possible to the v in pin and gnd. the capacitor c 2 has to be connected separately to the top led anode. a ground plane under the cat4240 allows for direct connection of the capacitors to ground. the resistor r 1 must be connected directly to the gnd pin of the cat4240 and not shared with the switching current loops and any other components. figure 26. closed ? switch current loop figure 27. open ? switch current loop vin cat4240 v in ldv out r1 c 1 fb switch closed shdn sw gnd c 2 vin cat4240 v in ldv out r1 c 1 fb switch open shdn sw gnd c 2 figure 28. recommended pcb layout
cat4240 http://onsemi.com 11 package dimensions tsot ? 23, 5 lead case 419ae ? 01 issue o e1 e a2 a1 e b d c a top view side view end view l1 l l2 notes: (1) all dimensions are in millimeters. angles in degrees. (2) complies with jedec mo-193. symbol min nom max a a1 a2 b c d e e1 e l 0o 8o l1 l2 0.01 0.80 0.30 0.12 0.30 0.05 0.87 0.15 2.90 bsc 2.80 bsc 1.60 bsc 0.95 typ 0.40 0.60 ref 0.25 bsc 1.00 0.10 0.90 0.45 0.20 0.50
cat4240 http://onsemi.com 12 example of ordering information (note 4) prefix device # suffix company id cat 4240 product number 4240 t3 t: tape & reel 3: 3,000 / reel tape & reel (note 7) (optional) td package td: thin sot ? 23 ? g g: nipdau lead finish (lead ? free, halogen ? free) series led drivers part number description cat4137 ? white led driver ? compliant (lead ? free, halogen ? free). 3. the standard lead finish is nipdau. 4. the device used in the above example is a cat4240td ? gt3 (tsot ? 23, nipdau, tape & reel, 3,000/reel). 5. for additional package and temperature options, please contact your nearest on semiconductor sales office. 6. switch current limit, typical values. 7. for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. cat4240/d publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5773 ? 3850 literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative

▲Up To Search▲

Price & Availability of CAT4240TD-GT3

	To Download CAT4240TD-GT3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .