View 4322-025-15101_5996336.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

technical note philips magnetic products philips components smd coil formers and cores
philips magnetic products 1 contents introduction 3 ferrite material properties 6 range overview 7 e5.3/2.7/2 8 e6.3/2.9/2 10 efd10 12 efd12 14 efd15 16 efd20 18 ep7 20 er9.5 22 er11 24 rm4/i 26 rm5/i 28 rm6s/i 30 rm6s/ilp 32 tag plate tgps-9 34 smd coil formers and cores
philips magnetic products 2 range of smd accessories and cores
philips magnetic products 3 introduction with its new range of surface-mount coil formers, philips components offers a real solution to circuit designers wishing to take maximum advantage of surface-mount technology in their designs. the trend toward full surface-mount technology has been hampered by the problems of introducing inductive components (inductors and transformers for example) in surface-mount execution. these devices, consisting of cores, coil-formers and windings held together by clips, were not easily converted to surface-mount versions, and former designs, based on "gull-wing" terminations (see fig.1) have not been entirely satisfactory. disadvantages of "gull-wing" pins in particular, tensions introduced by the winding wire, which is wrapped around the upper part of the gull-wing terminations, can severely degrade the coplanarity of the solder pads. the use of thin wire windings is a partial solution to this problem but this introduces limitations on coil design. furthermore, during soldering of the winding wire to the termination, spillage of solder onto the solder pad can further degrade coplanarity. however, for very small coil formers gull-wing pins are the only possible design due to space limitations. for small to medium sized coil formers there is a better solution: u-pins. > 0.1 mm fig.1 the gull-wing design.
philips magnetic products 4 advantages of the u-pin design the introduction of philips' new range of surface-mount, coil formers, however, solves all these problems. these feature "u-pin" terminations (fig.2) securely embedded in the plastic coil former body. these pins are thicker and wider than most gull-wing pins and therefore stronger. the solder pads, located beneath the plastic body and in contact with it, form a rigid structure with a guaranteed coplanarity of less than 0.1 mm, according to iec 191-2q. the upper part of the u-pins protrude from the plastic body and offer a large area on which to terminate the windings. since these are physically separated from the solder pads, tension introduced by the winding wire will not affect coplanarity, and neither will solder used to attach the winding wires spill onto the solder pads. the contact surface of the pads is also much larger than typical gull- wing solder pads, making them ideal for these relatively heavy components. moreover, with this design, the thickness of the winding wire is no longer a limitation, allowing circuit designers far more freedom in their choice of wire. high-grade plastic the coil former body is of high-grade liquid-crystal polymer (lcp) offering excellent thermal stability. the body is exceptionally tough and can withstand soldering temperatures up to 350 o c and operating temperatures up to 180 o c. excellent ferrites in combination with philips' extensive range of ferrite cores, these new coil formers provide surface-mount solutions in a host of applications from wide-band signal transformers to power transformers. when assembled with windings, coil-formers, cores and a newly-designed clip with a flat upper surface (ideal for vacuum pickup), the products can easily be inserted by a pick and place assembly line. < 0.1 mm clean solder pads fig.2 the u-pin design
philips magnetic products 5
philips magnetic products 6 initial permeability m i -f = 10 khz, b < 0.1mt, 1800 900 ~ 80 4700 10000 12000 t = 25 o c saturation flux density b s mt f = 10 khz, t = 25 o c ~ 500 ~ 450 ~ 330 ~ 360 ~ 360 ~ 400 at field strength h a/m 3000 3000 3000 250 250 250 remanence b r mt t = 25 o c ~ 150 ~ 150 ~ 200 ~ 100 ~ 80 ~ 100 coercivity h c a/m t = 25 o c ~ 15 ~ 60 ~ 170 ~ 10 ~ 5 ~ 4 power loss density p v kw/m 3 f = 25khz, b = 200mt 70 - - - - (typical, sine wave f = 100khz, b = 100mt 50 200 - - - excitation) f = 500khz, b = 50mt 180 180 - - - f = 1mhz, b = 30mt 300 140 300 - - f = 3mhz, b = 10mt - 240 150 - - curie temperature t c o c- 3 200 3 220 3 260 3 125 3 125 3 130 resistivity (dc) rw m t = 25 o c ~ 2 ~ 10 ~ 10 5 ~ 1 ~ 0.5 ~ 0.5 density g/cm 3 t = 25 o c ~ 4.8 ~ 4.7 ~ 4.6 ~ 4.8 ~ 4.9 ~ 4.9 ferrite material properties parameter symbol unit test conditions 3f3 3f4 4f1 3e4 3e5 3e6
philips magnetic products 7 range overview core type core materials smd 3f3 3f4 3e4 3e5 3e6 coil former e5.3/2.7/2 e6.3/2.9/2 efd10 efd12 efd15 efd20 ep7 er9.5 er11 rm4/i rm5/i rm6/i rm6/ilp efd assembly
philips magnetic products 8 1.6 5.5 1.85 1.2 4.9max. 4.7 max. 3.7 0 -0,15 5.3 max. 7.85 max. 2.6min. 2.15 +0.1 0 2.3 0.1 1.5 +0.1 0 2.9 0 -0.1 3.6 0.1 4.9 0.5 3.7 0.25 0.6 1.5 5.8 6 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless (crni) steel clamping force ~ 5n type number clm-e5.3/2 fig. 1 smd coil former for e5.3/2.7/2 fig. 2 clamp for e5.3/2.7/2 e5.3/2.7/2 winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 6 1.5 2.6 12.6 cphs e5.3/2-1s-6p 262 0.6 2 1.0 13 cphs e5.3/2-2s-6p 4.8 max 1.6 max 4.8 max fig. 3 cover for e5.3/2.7/2 cover material liquid crystal polymer (lcp) type number cov-e5.3/2 cover data
philips magnetic products 9 2.65 0.05 1.9 +0.1 0 2 0 -0.1 5.25 0.1 1.4 0 -0.1 3.8 +0.2 0 s (l/a) core factor (c1) 5.13 mm -1 v e effective volume 31.4 mm 3 l e effective length 12.7 mm a e effective area 2.5 mm 2 a min minimum area 2.3 mm 2 m mass of core half ~ 0.08 g 3f3 265 25% ~ 1080 ~ 0 e5.3/2.7/2-3f3 3f4 165 25% ~ 675 ~ 0 e5.3/2.7/2-3f4 3e5 1400 +40/-30% ~ 5700 ~ 0 e5.3/2.7/2-3e5 3e6 1600 +40/-30% ~ 6520 ~ 0 e5.3/2.7/2-3e6 b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core halves for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 300 0.005 0.008 - - 3f4 3 250 - - 0.006 0.010 fig. 3 e5.3/2.7/2 core half e5.3/2.7/2
philips magnetic products 10 5.08 0.6 4.4 3.5 0.08 2.9 0.05 3.5 0 - 0.1 1.5 +0.1 0 2.3 0.05 4.7 max. 5 max. 2.1 +0.1 0 2.7 min. 5.5 8.6 max. 6.4 max. 2.54 1.6 1.6 6.5 1.2 0.25 5.1 max. 7.7 max 6.9 max coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s cover material liquid crystal polymer (lcp) type number cov- e6.3/2 fig. 1 smd coil former for e6.3/2.9/2 fig. 2 cover for e6.3/2.9/2 e6.3/2.9/2 winding data coil former data cover data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 6 1.62 2.7 12.8 cphs- e6.3/2-1s-6p 262 0.45 2 0.75 12.8 cphs- e6.3/2-2s-6p
philips magnetic products 11 1.4 0 - 0.1 6.3 0 - 0.25 2 0 -0,1 1.85 + 0.1 0 2.9 0 - 0.1 3.6 + 0.2 0 s (l/a) core factor (c1) 3.67 mm -1 v e effective volume 40.6 mm 3 l e effective length 12.2 mm a e effective area 3.3 mm 2 a min minimum area 2.6 mm 2 m mass of core half ~ 0.12 g 3f3 360 25% ~ 1050 ~ 0 e6.3/2.9/2-3f3 3f4 225 25% ~ 660 ~ 0 e6.3/2.9/2-3f4 3e5 1700 +40/-30% ~ 4960 ~ 0 e6.3/2.9/2-3e5 3e6 2100 +40/-30% ~ 6130 ~ 0 e6.3/2.9/2-3e6 b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core halves for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 300 0.007 0.010 -- 3f4 3 250 - - 0.008 0.013 fig. 3 e6.3/2.9/2 core half e6.3/2.9/2
philips magnetic products 12 12 4.8+0.1 5.7-0.1 7.3-0.15 3 9 11.7max. 0.8 1.6+0.1 2.5-0.1 5.4max. 0.3 6.05min. 7.1-0.15 14.7max. 1.8 2 0.3 3 1.8 2.8 11 mbw122 10.5 0.2 4 10 - 0.3 12 - 0.3 9.4 2.5 8 8 mbw128 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clamp material stainless(crni) steel clamping force ~ 15n type number clm-efd10 fig. 1 smd coil former for efd10 fig. 2 clamp for efd10 efd10 winding data coil former data clamp data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 8 4.2 6.05 14.8 cphs-efd10-1s-8p
philips magnetic products 13 7.65 0.25 4.55 0.15 10.5 0.3 5.2 0.1 3.75 0.15 0.2 2.7 0.1 1.45 0.05 mbw131 s (l/a) core factor (c1) 3.29 mm -1 v e effective volume 171 mm 3 l e effective length 23.7 mm a e effective area 7.2 mm 2 a min minimum area 6.5 mm 2 m mass of core half ~ 0.45 g 3f3 255% ~ 66 ~ 540 efd10-3f3-a25-s 408% ~ 105 ~ 300 efd10-3f3-a40-s 6310% ~ 165 ~ 170 efd10-3f3-a63-s 50025% ~ 1290 ~ 0 efd10-3f3-s 3f4 255% ~ 66 ~ 520 efd10-3f4-a25-s 408% ~ 105 ~ 280 efd10-3f4-a40-s 6310% ~ 165 ~ 150 efd10-3f4-a63-s 28025% ~ 730 ~ 0 efd10-3f4-s 3e4 1400 +40/-30% ~ 3670 ~ 0 efd10-3e4-s 3e5 2000 +40/-30% ~ 5240 ~ 0 efd10-3e5-s b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 315 0.02 0.035 -- 3f4 3 250 -- 0.034 0.055 fig. 3 efd10 core half efd10
philips magnetic products 14 1.8 2.8 12.5 3 13.4 1.8 16.2max. 2 3 0.8 9 13.7max. 5.65+0.1 6.55-0.1 8.65-0.15 2.2+0.1 3.1-0.1 6.2max. 0.3 7.65min. 8.7-0.15 0.3 mbw123 12.5 0.2 4 12 - 0.3 14 - 0.3 11.5 2.5 9.4 10.5 mbw129 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clamp material stainless(crni) steel clamping force ~ 20n type number clm-efd12 fig. 1 smd coil former for efd12 fig. 2 clamp for efd12 efd12 winding data coil former data clamp data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 8 6.5 7.65 18.6 cphs-efd12-1s-8p
philips magnetic products 15 2 0.1 3.5 0.1 0.2 4.55 0.15 6.2 0.1 12.5 0.3 5.4 0.15 9 0.25 mbw132 s (l/a) core factor (c1) 2.50 mm -1 v e effective volume 325 mm 3 l e effective length 28.5 mm a e effective area 11.4 mm 2 a min minimum area 10.7 mm 2 m mass of core half ~ 0.9 g 3f3 405% ~ 80 ~ 490 efd12-3f3-a40-s 638% ~ 125 ~ 280 efd12-3f3-a63-s 10010% ~ 200 ~ 160 efd12-3f3-a100-s 70025% ~ 1370 ~ 0 efd12-3f3-s 3f4 405% ~ 80 ~ 470 efd12-3f4-a40-s 638% ~ 125 ~ 260 efd12-3f4-a63-s 10010% ~ 200 ~ 140 efd12-3f4-a100-s 38025% ~ 760 ~ 0 efd12-3f4-s 3e4 1900 +40/-30% ~ 3780 ~ 0 efd12-3e4-s 3e5 2800 +40/-30% ~ 5570 ~ 0 efd12-3e5-s b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 315 0.04 0.065 -- 3f4 3 250 -- 0.065 0.11 fig. 3 efd12 core half efd12
philips magnetic products 16 1.8 16 1 0.3 2 0.3 7.5 max 10.4 - 0.15 9.15 min 18.7 max 3.7 - 0.1 2.6 + 0.1 10.55 - 0.15 6.65 - 0.1 5.55+0.1 16.7 max 11.25 3.75 2 2.8 15 3.75 mbw143 5 2.6 19 13.3 4.5 mbw144 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless(crni) steel clamping force ~ 12.5n each type number cli-efd15 fig. 1 smd coil former for efd15 fig. 2 clip for efd15 efd15 winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm2) (mm) of turn (mm) 1 8 16.7 9.15 25.6 cphs-efd15-1s-8p 12.5 15 0.2 4 13.5 16.5 0 -0.3 14.3 0.2 4 12 fig. 2 clamp for efd15 clamp material stainless(crni) steel clamping force ~ 25n type number clm-efd15 clamp data
philips magnetic products 17 4.65 0.15 0.2 5.5 0.25 7.5 0.15 15 0.4 5.3 0.15 2.4 0.1 11 0.35 mbw145 s (l/a) core factor (c1) 2.27 mm -1 v e effective volume 510 mm 3 l e effective length 34.0 mm a e effective area 15.0 mm 2 a min minimum area 12.2 mm 2 m mass of core half ~ 1.4 g 3f3 635% ~ 115 ~ 350 efd15-3f3-a63-s 1008% ~ 180 ~ 170 efd15-3f3-a100-s 16010% ~ 290 ~ 100 efd15-3f3-a160-s 78025% ~ 1400 ~ 0 efd15-3f3-s 3f4 635% ~ 115 ~ 350 efd15-3f4-a63-s 1008% ~ 180 ~ 160 efd15-3f4-a100-s 16010% ~ 290 ~ 90 efd15-3f4-a160-s 40025% ~ 720 ~ 0 efd15-3f4-s 3e4 2000 +40/-30% ~ 3610 ~ 0 efd15-3e4-s 3e5 3 2500 3 4510 ~ 0 efd15-3e5-s b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 315 0.06 0.10 -- 3f4 3 250 -- 0.10 0.16 fig. 3 efd15 core half efd15
philips magnetic products 18 7.5 0.05 15 0.05 21.7 max 9.2 + 0.1 10.5 - 0.15 14.8 - 0.2 3.9 + 0.1 5 -0.1 9.5 max 23.7 max 13.5 min 14.8-0.2 0.3 2 0.3 20 2.8 2 3.75 1 21 1.8 mbw148 5 4 24 18.3 6 mbw146 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless(crni) steel clamping force ~ 20n each type number cli-efd20 fig. 1 smd coil former for efd20 fig. 2 clip for efd20 efd20 winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 10 27.7 13.5 34.1 cphs-efd20-1s-10p 4 20 0.2 17.5 4.7 19.3 0.2 17 21.5 0 - 0.3 18.5 fig. 2 clamp for efd20 clamp material stainless(crni) steel clamping force ~ 30n type number clm-efd20 clamp data
philips magnetic products 19 6.65 0.15 7.7 0.25 10 0.15 20 0.55 8.9 0.2 3.6 0.15 15.4 0.5 mbw147 0.17 s (l/a) core factor (c1) 1,52 mm -1 v e effective volume 1460 mm 3 l e effective length 47.0 mm a e effective area 31.0 mm 2 a min minimum area 29.0 mm 2 m mass of core half ~ 3.5 g 3f3 633% ~ 75 ~ 500 efd20-3f3-e63-s 1003% ~ 120 ~ 240 efd20-3f3-a100-s 1605% ~ 195 ~ 140 efd20-3f3-a160-s 2508% ~ 300 ~ 90 efd20-3f3-a250-s 31510% ~ 425 ~ 65 efd20-3f3-a315-s 120025% ~ 1450 ~ 0 efd20-3f3 3f4 633% ~ 75 ~ 500 efd20-3f4-e63-s 1003% ~ 120 ~ 240 efd20-3f4-a100-s 1605% ~ 195 ~ 140 efd20-3f4-a160-s 2508% ~ 300 ~ 90 efd20-3f4-a250-s 31510% ~ 425 ~ 65 efd20-3f4-a315-s 65025% ~ 785 ~ 0 efd20-3f4 b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core halves/sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 315 0.17 0.28 -- 3f4 3 300 -- 0.44 0.50 fig. 3 efd20 core half efd20
6 2.8 3 1.8 3.9min. 4.9-0.1 7.15 1.8 9.85max. 2 0.8 3 6 9.2max. 3.5+0.1 4.5-0.1 7-0.1 0.3 7.3max. 0.3 mbw124 9 0.25 6.9-0.3 4.3 9.4+0,2 4 mbw130 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless(crni) steel clamping force ~ 22n type number cli-ep7 fig. 1 smd coil former for ep7 fig. 2 clip for ep7 ep7 winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm2) (mm) of turn (mm) 1 6 4.7 3.9 17.9 cphs-ep7-1s-6p philips magnetic products 20
7.5 - 0.2 5 + 0.4 9.4 - 0.4 6.5 - 0.3 1.7 0.1 3.4 - 0.2 7.2 + 0.4 mbw133 s (l/a) core factor (c1) 1.45 mm -1 v e effective volume 165 mm 3 l e effective length 15.5 mm a e effective area 10.7 mm 2 a min minimum area 8.55 mm 2 m mass of core set ~ 0.8 g 3f3 253% ~ 30 ~ 790 ep7-3f3-e25 403% ~ 48 ~ 440 ep7-3f3-a40 633% ~ 76 ~ 260 ep7-3f3-a63 1003% ~ 121 ~ 150 ep7-3f3-a100 1605% ~ 193 ~ 85 ep7-3f3-a160 100025% ~ 1210 ~ 0 ep7-3f3 3f4 1003% ~ 121 ~ 150 ep7-3f4-a100 1605% ~ 193 ~ 85 ep7-3f4-a160 60025% ~ 730 ~ 0 ep7-3f4 3e5 5200 +40/-30% ~ 6300 ~ 0 ep7-3e5 3e6 5800 +40/-30% ~ 7000 ~ 0 ep7-3e6 b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 315 0.02 0.035 -- 3f4 3 250 -- 0.033 0.053 fig. 3 ep7 core set ep7 philips magnetic products 21
philips magnetic products 22 1.6 10 1.6 2 6 2 0.7 8.1 3.6 0.08 ? 4.45 0.08 ? 7.3 0,1 ? 4.4 max. 2.05 min. 11.7 max. 0.25 2.95 0.1 8.6 max. 5.5 9.8 4 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clamp material stainless(crni)steel clamping force ~ 20n type number clm-er9.5 fig. 1 smd coil former for er9.5 fig. 2 clamp for er9.5 er9.5 winding data coil former data clamp data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 8 2.8 2.05 18.4 cpvs-er9.5-1s-8p
philips magnetic products 23 9.5 0 - 0.3 7.1 + 0.2 0 7.5 + 0.25 0 3.5 0 - 0.2 5 0 - 0.2 2.45 0.05 1.6 +0.15 0 s (l/a) core factor (c1) 1.67 mm -1 v e effective volume 120 mm 3 l e effective length 14.2 mm a e effective area 8.47 mm 2 a min minimum area 7.60 mm 2 m mass of core half ~ 0.35 g 3f3 85025% ~ 1145 ~ 0 er9.5-3f3-s 3f4 52525% ~ 700 ~ 0 er9.5-3f4-s 3e5 3600 +40/-30% ~ 4780 ~ 0 er9.5-3e5-s 3e6 4800 +40/-30% ~ 6380 ~ 0 er9.5-3e6-s b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 300 0.015 0.025 -- 3f4 3 250 -- 0.024 0.038 fig. 3 er9.5 core half er9.5
philips magnetic products 24 10.6 max. 2.8 0.1 0.25 12.35 max. 1.85 min. 4.4 max. 8.5 +0.1 -0.2 ? 5.3 0.1 ? 4.5 0.1 ? 9.2 4 8 0.7 1.6 2 1.6 10 4.4 11.5 5.6 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless(crni) steel clamping force ~ 25n type number clm-er11 fig. 1 smd coil former for er11 fig. 2 clamp for er11 er11 winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 10 2.8 1.85 21.6 cpvs-er11-1s-10p
philips magnetic products 25 2.45 0.05 4.25 0 - 0.25 1.5 +0.15 0 11 0 - 0.35 6 0 - 0.2 8.7 +0.3 0 8 +0.2 0 s (l/a) core factor (c1) 1.23 mm -1 v e effective volume 174 mm 3 l e effective length 14.7 mm a e effective area 11.9 mm 2 a min minimum area 10.3 mm 2 m mass of core half ~ 0.5 g 3f3 120025% ~ 1170 ~ 0 er11-3f3-s 3f4 72525% ~ 710 ~ 0 er11-3f4-s 3e5 5000 +40/-30% ~ 4890 ~ 0 er11-3e5-s 3e6 6700 +40/-30% ~ 6560 ~ 0 er11-3e6-s b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number properties of core sets under power conditions 3f3 3 300 0.025 0.040 -- 3f4 3 250 -- 0.035 0.056 fig. 3 er11 core half er11
philips magnetic products 26 1 8.8 max 1.8 2 7 0.4 6.8-0.1 (5.7 min) 0.3 7.85-0.15 ? 4.9-0.1 ? 4+0.1 ? 10.65 max 7.5 2.8 8.5 3.75 2 11.15 max mbw125 2.1 9.3 8.2 22 r coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless steel clamping force ~ 5 n each type number cli-rm4/5 fig. 1 smd coil former for rm4/i fig. 2 clip for rm4/i rm4/i winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 6 8.4 5.75 19.8 cpvs-rm4-1s-6p
philips magnetic products 27 9.8 - 0.4 4.6 - 0.2 > 5.8 7 + 0.4 10.4 0.1 9 0.25 3.9 - 0.2 ? ? 7.95 + 0.4 11 - 0.5 2.5 mbw134 s (l/a) core factor (c1) 1.69 mm -1 v e effective volume 322 mm 3 l e effective length 23.3 mm a e effective area 13.8 mm 2 a min minimum area 11.5 mm 2 m mass of core set ~ 1.7 g b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit properties of core sets under power conditions 3f3 3 300 0.05 0.07 -- 3f4 3 250 -- 0.065 0.11 fig. 3 rm4/i core set rm4/i 3f3 1003% ~ 134 ~ 170 rm4/i-3f3-a100 1603% ~ 215 ~ 100 rm4/i-3f3-a160 25010% ~ 336 ~ 50 rm4/i-3f3-a250 95025% ~ 1280 ~ 0 rm4/i-3f3 3f4 1003% ~ 134 ~ 150 rm4/i-3f4-a100 1603% ~ 215 ~ 80 rm4/i-3f4-a160 25010% ~ 336 ~ 40 rm4/i-3f4-a250 56025% ~ 750 ~ 0 rm4/i-3f4 3e5 3500 +40/-30% ~ 4700 ~ 0 rm4/i-3e5 core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number
philips magnetic products 28 1.8 5 +0.1 0 ? 0.3 8.45 max. 1 14.25 max. 11.25 3.75 5.9 0 - 0.1 ? 10.1 0 - 0.15 ? 2 14.9 max. 0.4 6.1 4.9 min. 2.8 11.2 3.75 2 0.9 2.1 9.3 8.2 22 r coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless (crni)steel clamping force ~ 5 n each type number cli-rm4/5 fig. 1 smd coil former for rm5/i fig. 2 clip for rm5/i rm5/i winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 8 9.8 4.9 24.9 cpvs-rm5-1s-8p
philips magnetic products 29 6.3 + 0.4 10.4 0.1 9.1 0.25 4.9 - 0.2 ? ? 10.2 + 0.4 14.6 - 0,6 > 6 6.8 - 0.4 2.5 12.3 - 0.5 mbw135 s (l/a) core factor (c1) 0.935 mm -1 v e effective volume 574 mm 3 l e effective length 23.2 mm a e effective area 24.8 mm 2 a min minimum area 18.1 mm 2 m mass of core set ~ 3.3 g b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit properties of core sets under power conditions 3f3 3 315 0.08 0.11 -- 3f4 3 250 -- 0.11 0.20 fig. 3 rm5/i core set rm5/i 3f3 1003% ~ 74 ~ 300 rm5/i-3f3-a100 1603% ~ 119 ~ 160 rm5/i-3f3-a160 2503% ~ 186 ~ 90 rm5/i-3f3-a250 170025% ~ 1270 ~ 0 rm5/i-3f3 3f4 1003% ~ 74 ~ 300 rm5/i-3f4-a100 1603% ~ 119 ~ 160 rm5/i-3f4-a160 2503% ~ 186 ~ 90 rm5/i-3f4-a250 100025% ~ 750 ~ 0 rm5/i-3f4 3e5 6700 +40/-30% ~ 4980 ~ 0 rm5/i-3e5 3e6 9500 +40/-30% ~ 7050 ~ 0 rm5/i-3e6 core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number
philips magnetic products 30 13.7 2.8 2 3.75 5 3.75 1 15.7 max 5 12.5 7.55-0.15 ? 12.3-0.25 ? 10.5 max 0.3 2.2 6.5+0.15 ? 17.45 max 1.8 14.7 2 0.5 6.25 min 7.9-0.1 mbw127 2.3 9.45 11.7 30 r mbw138 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless (crni) steel clamping force ~ 10 n each type number cli-rm6 fig. 1 smd coil former for rm6s/i fig. 2 clip for rm6s/i rm6s/i winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 8 14 6.25 31 cpvs-rm6s-1s-8p
philips magnetic products 31 10.35 0.25 17.9 - 0.7 2.8 8.2 - 0.4 ? 12.4 + 0.5 8 + 0.4 12.4 0.1 ? 6.4 - 0.2 > 8.8 14.7 - 0.6 mbw136 s (l/a) core factor (c1) 0.784 mm -1 v e effective volume 1090 mm 3 l e effective length 29.2 mm a e effective area 37.0 mm 2 a min minimum area 31.2 mm 2 m mass of core set ~ 4.9 g b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit properties of core sets under power conditions 3f3 3 315 0.14 0.20 -- 3f4 3 250 -- 0.22 0.35 fig. 3 rm6s/i core set rm6s/i 3f3 633% ~ 39 ~ 950 rm6s/i-3f3-a63 1003% ~ 62 ~ 500 rm6s/i-3f3-a100 1603% ~ 100 ~ 300 rm6s/i-3f3-a160 2503% ~ 156 ~ 1 50 rm6s/i-3f3-a250 215025% ~ 1350 ~ 0 rm6s/i-3f3 3f4 633% ~ 39 ~ 950 rm6s/i-3f4-a63 1003% ~ 62 ~ 500 rm6s/i-3f4-a100 1603% ~ 100 ~ 300 rm6s/i-3f4-a160 2503% ~ 156 ~ 150 rm6s/i-3f4-a250 125025% ~ 780 ~ 0 rm6s/i-3f4 3e5 8600 +40/-30% ~ 5370 ~ 0 rm6s/i-3e5 3e6 12500 +40/-30% ~ 6200 ~ 0 rm6s/i-3e6 core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number
philips magnetic products 32 4.4 - 0.1 2.8 min 0.5 2 14.7 1.8 17.45 max 6.5 +0.15 ? 2.2 0.3 7.0 max 12.3 - 0.25 ? 7.55 - 0.15 ? 12.5 5 15.7 max 1 3.75 5 3.75 2 2.8 13.7 mbw142 2.3 5.95 7.5 16 r coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s clip material stainless (crni) steel clamping force ~ 10 n each type number cli-rm6/lp fig. 1 smd coil former for rm6s/ilp fig. 2 clip for rm6s/ilp rm6s/ilp winding data coil former data clip data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) 1 8 6.4 2.8 min 31.0 cpvs-rm6s/lp-1s-8p
philips magnetic products 33 6.84 0.25 ? 12.4 +0.5 4.5 + 0.4 9 - 0.2 ? 6.4 - 0.2 17.9 - 0.7 2.8 8.2 - 0.4 > 8.8 14.7 - 0.6 mbw140 s (l/a) core factor (c1) 0.580 mm -1 v e effective volume 820 mm 3 l e effective length 21.8 mm a e effective area 37.5 mm 2 a min minimum area 31.2 mm 2 m mass of core set ~ 4.2 g b(mt) at core loss at core loss at core loss at core loss at grade h = 250 a/m f = 100 khz f = 400 khz f = 1mhz f = 3mhz f = 25khz b = 100mt b = 50mt b = 30mt b = 10mt t = 100 o c t = 100 o c t = 100 o c t = 100 o c t = 100 o c effective core parameters symbol parameter value unit properties of core sets under power conditions 3f3 3 300 0.10 0.15 -- 3f4 3 250 -- 0.16 0.26 fig. 3 rm6s/ilp core set rm6s/ilp 3f3 270025% ~ 1250 ~ 0 rm6s/ilp-3f3 3f4 160025% ~ 740 ~ 0 rm6s/ilp-3f4 3e5 10500 +40/-30% ~ 4850 ~ 0 rm6s/ilp-3e5 3e6 15000 +40/-30% ~ 6930 ~ 0 rm6s/ilp-3e6 core sets for general purpose transformers and power applications grade a l (nh) m e airgap ( m m) type number
philips magnetic products 34 1.8 12 11 2.8 3 3 9 0.8 2 14.7 max. 10.8 min. 0.3 1.8 13 max. 1.75 max. 45 ? 0.6 (4x) 6 max. 11 0.1 11.7 max 0.6 coil former material liquid crystal polymer (lcp), glass reinforced, flame retardant in accordance with ul94v-0. solder pad material copper-tin alloy (cusn), tin-lead alloy (snpb) plated maximum operating temperature 155 o c, iec 85 class f resistance to soldering heat iec 68-2-20 part2, test tb, method 1b: 350 o c, 3.5s. solderability iec 68-2-20 part2, test ta, method 1: 235 o c, 2s cover material polyamide (pa4.6) glass reinforced, flame retardant in accordance with ul94v-0. maximum operating 130 o c, iec 85 class b temperature type number cov-9 fig. 1 tag plate for 9mm ring cores. fig. 2 cover for tgps-9 tgps-9 winding data coil former data cover data number of number of winding area winding width average length type number sections solder pads (mm 2 ) (mm) of turn (mm) - 8 - - - tgps-9
philips magnetic products 35 9.4 0.3 5.5 0.3 3.4 0.3 s (l/a) core factor (c1) 5.17 mm -1 v e effective volume 102 mm 3 l e effective length 22.9 mm a e effective area 4.44 mm 2 m mass of core ~ 0.5 g effective core parameters symbol parameter value unit fig. 3 tn9/6/3 ring core 3f3 440 25% ~ 1800 blue tn9/6/3-3f3 3e5 1) 2070 30% ~ 8500 yellow/white tl9/6/3-3e5 3e6 2) 2435 30% ~ 10000 purple/white tc9/6/3-3e6 ring core data grade a l (nh) m e colour code type number tn9/6/3 note 1. ring cores in 3e5 are lacquered and therefore have different dimensions: od = 9.30.4 mm, id = 5.750.3mm, h = 3.250.3mm. 2. ring cores in 3e6 are coated with parylene and therefore have different dimensions: od = 9.00.2 mm, id = 6.00.2mm, h = 3.0 0.15mm.
philips components philips components - a worldwide company australia: philips components pty ltd., north ryde, tel. +61 2 9805 4455, fax. +61 2 9805 4466 austria: ?sterreichische philips industrie gmbh, wien, tel. +43 1 60 101 12 41, fax. +43 1 60 101 12 11 belarus: philips office belarus, minsk, tel. +375 172 200 924/733, fax. +375 172 200 773 benelux: philips nederland b.v., eindhoven, nl, tel. +31 40 2783 749, fax. +31 40 2788 399 brazil: philips components, s?o paulo, tel. +55 11 821 2333, fax. +55 11 829 1849 canada: philips electronics ltd., scarborough, tel. +1 416 292 5161, fax. +1 416 754 6248 china: philips company, shanghai, tel. +86 21 6354 1088, fax. +86 21 6354 1060 denmark: philips components a/s, copenhagen s, tel. +45 3329 3333, fax. +45 3329 3905 finland: philips components, espoo, tel. +358 9 615 800, fax. +358 9 615 80510 france: philips composants, suresnes, tel. +33 1 4099 6161, fax. +33 1 4099 6493 germany: philips components gmbh, hamburg, tel. +49 40 2489-0, fax. +49 40 2489 1400 greece: philips hellas s.a., tavros, tel. +30 1 4894 339/+30 1 4894 239, fax. +30 1 4814 240 hong kong: philips hong kong, kowloon, tel. +852 2784 3000, fax. +852 2784 3003 india: philips india ltd., mumbai, tel. +91 22 4930 311, fax. +91 22 4930 966/4950 304 indonesia: p.t. philips development corp., jakarta, tel. +62 21 794 0040, fax. +62 21 794 0080 ireland: philips electronics (ireland) ltd., dublin, tel. +353 1 7640 203, fax. +353 1 7640 210 israel: rapac electronics ltd., tel aviv, tel. +972 3 6450 444, fax. +972 3 6491 007 italy: philips components s.r.l., milano, tel. +39 2 6752 2531, fax. +39 2 6752 2557 japan: philips japan ltd., tokyo, tel. +81 3 3740 5135, fax. +81 3 3740 5035 korea (republic of): philips electronics (korea) ltd., seoul, tel. +82 2 709 1472, fax. +82 2 709 1480 malaysia: philips malaysia sdn berhad, components division, pulau pinang, tel. +60 3 750 5213, fax. +60 3 757 4880 mexico: philips components, el paso, u.s.a., tel. +52 915 772 4020, fax. +52 915 772 4332 new zealand: philips new zealand ltd., auckland, tel. +64 9 815 4000, fax. +64 9 849 7811 norway: norsk a/s philips, oslo, tel. +47 22 74 8000, fax. +47 22 74 8341 pakistan: philips electrical industries of pakistan ltd., karachi, tel. +92 21 587 4641-49, fax. +92 21 577 035/+92 21 587 4546 philippines: philips semiconductors philippines inc., metro manila, tel. +63 2 816 6345, fax. +63 2 817 3474 poland: philips poland sp. z.o.o., warszawa, tel. +48 22 612 2594, fax. +48 22 612 2327 portugal: philips portuguesa s.a., philips components: linda-a-velha, tel. +351 1 416 3160/416 3333, fax. +351 1 416 3174/416 3366 russia: philips russia, moscow, tel. +7 95 755 6918, fax. +7 95 755 6919 singapore: philips singapore pte ltd., singapore, tel. +65 350 2000, fax. +65 355 1758 south africa: s.a. philips pty ltd., johannesburg, tel. +27 11 470 5911, fax. +27 11 470 5494 spain: philips components, barcelona, tel. +34 93 301 63 12, fax. +34 93 301 42 43 sweden: philips components ab, stockholm, tel. +46 8 5985 2000, fax. +46 8 5985 2745 switzerland: philips components ag, zrich, tel. +41 1 488 22 11, fax. +41 1 481 7730 taiwan: philips taiwan ltd., taipei, tel. +886 2 2134 2900, fax. +886 2 2134 2929 thailand: philips electronics (thailand) ltd., bangkok, tel. +66 2 745 4090, fax. +66 2 398 0793 turkey: trk philips ticaret a.s., gltepe/istanbul, tel. +90 212 279 2770, fax. +90 212 282 6707 united kingdom: philips components ltd., dorking, tel. +44 1306 512 000, fax. +44 1306 512 345 united states: ? display components, ann arbor, mi, tel. +1 734 996 9400, fax. +1 734 761 2776 ? magnetic products, saugerties, ny, tel. +1 914 246 2811, fax. +1 914 246 0487 ? passive components, san jose, ca, tel. +1 408 570 5600, fax. +1 408 570 5700 yugoslavia (federal republic of): philips components, belgrade, tel. +381 11 625 344/373, fax. +381 11 635 777 internet: ? display components: www.dc.comp.philips.com ? passive components: www.passives.comp.philips.com for all other countries apply to: philips components, building bf-1, p.o. box 218, 5600 md eindhoven, the netherlands, fax. +31-40-27 23 903. cob20 philips electronics n.v. 1998 all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. printed in the netherlands xxxx xxx xxxxx date of release: 11/98 printed in the netherlands 9398 237 50011 date of release: 6/97
magnetic products nafta sales offices alabama over and over, inc., charlotte, nc (708) 583-9100 alaska eclipse marketing group, redmond, wa (206) 885-6991 arizona harper and two, tempe, az (602) 804-1290 arkansas philips components, willoughby, oh (440) 269-8585 california - northern criterion sales, santa clara, ca (408) 988-6300 california - southern harper and two, signal hill, ca (801) 264-8050 colorado philips components, willoughby, oh (440) 269-8585 connecticut philips components, woburn, ma (617) 932-4748 deleware philips components, woburn, ma (617) 932-4748 florida over and over, charlotte, nc (704) 583-9100 georgia over and over, charlotte, nc (704) 583-9100 hawaii harper and two, signal hill, ca (310) 424-3030 idaho - northern eclipse marketing group, redmond, wa (206) 885-6991 idaho - southern electrodyne, inc., salt lake city, ut (801) 264-8050 illinois - northern philips components, willoughby, oh (440) 269-8585 illinois - quad cities lorenz sales, cedar rapids, ia (319) 377-4666 illinois - southern lorenz sales, st. louis, mo (314) 997-4558 indiana - northern corrao marsh, fort wayne, in (219) 482-2725 indiana - central and southern corrao marsh, green eld, in (317) 462-4446 iowa - all except quad cities lorenz sales, cedar rapids, ia (319) 377-4666 kansas - northeast lorenz sales, overland park, ks (913) 469-1312 kansas - all except northeast lorenz sales, wichita, ks (316) 721-0500 kentucky corrao marsh, green eld, in (317) 462-4446 louisiana philips components, willoughby, oh (440) 269-8585 maine philips components, woburn, ma (617) 932-4748 maryland philips components, willoughby, oh (440) 269-8585 massachusetts philips components, woburn, ma (617) 932-4748 michigan philips components, willoughby, oh (440) 269-8585 minnesota electronic component sales, minneapolis, mn (612) 946-9510 mississippi over and over, charlotte, nc (704) 583-9100 missouri - eastern lorenz sales, st. louis, mo (314) 997-4558 missouri - western lorenz sales, overland park, ks (913) 469-1312 montana electrodyne, inc., salt lake city, ut (801) 264-8050 nebraska lorenz sales, cedar rapids, ia (319) 377-4666 nevada - central and northern criterion sales, santa clara, ca (408) 988-6300 nevada - sourthern harper and two, tempe, az (602) 804-1290 new hampshire philips components, woburn, ma (617) 932-4748 new jersey philips components, woburn, ma (617) 932-4748 new mexico harper and two, tempe, az (602) 804-1290 new york - western philips components, willoughby, oh (440) 269-8585 new york - all other philips components, woburn, ma (617) 932-4748 north carlolina over and over, charlotte, nc (704) 583-9100 north dakota electronic component sales, minneapolis, mn (612) 946-9510 ohio philips components, willoughby, oh (440) 269-8585 oklahoma philips components, willoughby, oh (440) 269-8585 oregon eclipse marketing group, beaverton, or (503) 642-1661 pennsylvania - western philips components, willoughby, oh (440) 269-8585 pennsylvania - eastern philips components, woburn, ma (617) 932-4748 rhode island philips components, woburn, ma (617) 932-4748 south carolina over and over, charlotte, nc (704) 583-9100 south dakota electronic component sales, minneapolis, mn (612) 946-9510 tennesse over and over, charlotte, nc (704) 583-9100 texas philips components, willoughby, oh (440) 269-8585 utah electrodyne, inc., salt lake city, ut (801) 264-8050 vermont philips components, woburn, ma (617) 932-4748 virginia philips components, willoughby, oh (440) 269-8585 washington eclipse marketing group, redmond, wa (206) 885-6991 washington dc philips components, willoughby, oh (440) 269-8585 west virginia philips components, willoughby, oh (440) 269-8585 wisconsin philips components, willoughby, oh (440) 269-8585 wyoming electrodyne, inc., salt lake city, ut (801) 264-8050 canada philips components, scarborough, on (416) 292-5161 mexico philips components, el paso, tx (915) 772-4020 puerto rico max anderson co., caperra heights, pr (809) 783-6544 virgin islands max anderson co., caperra heights, pr (809) 783-6544

▲Up To Search▲

Price & Availability of 4322-025-15101

	To Download 4322-025-15101 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .