rev 02.24.05 technical support: (888) 41-astec or (407) 241-2752 americas: (760) 930-4600 europe (uk) 44 (1384) 842-211 asia (hk) 852-2437-96622 special features electrical specs 350-1400 watts hps35 series ? active power factor correction ? en61000-3-2 compliant ? cispr22, en55022 class-b conducted/radiated emi ? en61000 immunity standards ?5v sb @2a ? overvoltage protection (ovp) ? overcurrent protection (ocp) ? overtemperature protection (otp) ? ac ok signal and indicator led ? dc ok signal and indicator led ? remote inhibit ? remote sense on main output ?hot plug ? n+1 redundant ? optional i 2 c board (pending) voltage monitoring current monitoring remote on/off dc ok / ac ok temperature fan fail input input voltage 90-264 vac typical frequency 47-440 hz inrush current 40 a peak typical @ 25c efficiency 80% typ @ full load, 230 vac power factor 0.98 typical @ 115 vac, full load turn-on time ac - on 2 sec. inhibit / enable 160 ms emi filter standard cispr 22 en55022 level ?b? leakage current standard <0.5 ma max @ 230 vac @ 60hz (per module) radiated emi cispr 22 en55022 level ?b? holdup time 20 ms minimum (independent of input vac) ac ok 5 ms early warning minimum before outputs lose regulation harmonic distortion meets en61000-3-2 isolation meets en60950 output adjustability 5% of nominal output voltage overall reg <3% ripple 1% of vout pk - pk (20 mhz bandwidth) dynamic response 4% with 50% load step recovery time to within 1% in <300 sec overcurrent protection 115%-130% of rated output current short circuit protection protected for continuous short circuit. auto recovery. overvoltage protection 120 - 140% . ac reset. reverse voltage protection 100% of rated output current thermal protection main and aux disabled when internal temp exceeds safe operating range. remote sense up to 0.5 v total drop single wire parallel current share to within 10% of total rated current on main output dc ok 5% of nominal minimum load* none required (as a standalone module) standby voltage 5 vdc @2a max. present whenever ac input is applied global inhibit logic ?0? *3a minimum required for current share operation environmental t o t a l p p o w e r : 3 5 0 w i n p u t v v o l t a g e : 9 0 -2 2 6 4 v a c # o o f o o u t p u t s : o n e & & s s t a n d b y ul ul60950-1, 1st ed. (april 1, 2003) c s a csa c22.2 60950-1-03 tuv en60950-1:2001 (1st ed.) cb iec60950-1, 1st ed. (2001) ce mark (lvd) operating temperature: 0c to +50c ambient, derate output @ 2.5% per degree from 50c to 70c shock: operating - 4g, half since, 22 ms minimum duration, all 6 faces non-operating: 30g, half since, 6 ms minimum duration, all 6 faces random vibration operating: 1g rms, 20 min/axis non-operating: 12.5g rms, 20min/axis humidity: 95% non-condensing storage temperature: -40c to +85c temperature coefficient: 0.04% per c cooling: internal dc fans safety
asia units 2111-2116, level 21 tower1, metroplaza 223, hing fong road fwai fong, new territories hong kong telephone: 852-2437-9662 facsimile: 852-2402-4426 e e u u r r o o p p e e astec house, waterfront business park merry hill, dudley west midlands, dy5 1lx, uk telephone: 44 (1384) 842-211 facsimile: 44 (1384) 843-355 a a m m e e r r i i c c a a s s 5810 van allen way carlsbad, ca 92008 telephone: 760-930-4600 facsimile: 760-930-0698 www.astecpower.com watts 350 input voltage 90-264 module id hps35 code volts output amps l 12.0 29.2 w 48.0 7.3 module max. size max. module number unit code (h x w x l) power per rack weight (lbs) hps35 1.6" x 4.3" x 10.5" 350 w 4 3.2 modules output voltage l = 12 v w = 48 v power 35 = 350 w 50 = 500 w hps xxx special options & modifications contact astec n n 0 0 0 n r h h p p s s 3 3 5 5 l l -n n n n r r -0 0 0 0 0 0 hps35 7.6 53.8 hps35l-nnr-000 maximum output power is 350w date: yyww s/n: mmmmwwssssrrc made in philippines input: 90 - 240vac - 40a 50/60 hz serial no.: output: +12v / 29a rev: xx a/c code: xxxx 73-811-029
north america (usa): 1-888-41-astec europe (uk): 44 (1384) 842-211 asia (hk): 852-2437-9662 154 pin assignments rev 02.24.05 h h p p s s 3 3 5 5 m m o o d d u u l l e e m a t i n g c c o n n e c t o r : edac 307-048-520-201 or equivalent rating: 5a per contact u n i t c c o n n e c t o r card edge connector with gold fingers double-sided 1.6mm fr-4 pcb p p i i n n 6 6 - s s w w p p (in/out signal) ( ( s s i i n n g g l l e e w w i i r r e e p p a a r r a a l l l l e e l l ) ) swp pin is used when connecting units in parallel to achieve current sharing. current share accuracy is typically 10% of full load. note: swp voltage is 5v at 100% load current p p i i n n 2 2 3 3 - f f a a n n m m o o n n i i t t o o r r (out signal) p p i i n n z z - a a c c o o k k (out signal) p p i i n n f f - --r r e e m m o o t t e e s s e e n n s s e e p p i i n n h h - + + r r e e m m o o t t e e s s e e n n s s e e compensates for up to 0.5v drop. recommended shielded twisted wire pair. p p i i n n x x - m m o o d d u u l l e e i i n n h h i i b b i i t t (in signal) note: swp voltage is 5v at 100% load current note: hi state: source 100ua @ 4v low state: sink 10ma @ 0.5v p p i i n n a a a a - d d c c o o k k (out signal) u n i t c c o n n e c t o r card edge connector with gold fingers double-sided 1.6mm fr-4 pcb pin description 1 ac (l) 2 blank 3 ac (n) 4 blank 5 gnd 6 swp 7 5v rtn 8 common 9 common 10 common 11 common 12 common 13 common 14 v out 15 v out 16 v out 17 v out 18 v out 19 v out 20 blank 21 +5 standby 22 tba 23 fan mon 24 i 2 c clk pin description a ac (l) b blank c ac (n) d blank e gnd f -sense h +sense j common k common l common m common n common p common r v out s v out t v out u v out v v out w v out x inhibit y tba z ac ok aa dc ok bb i 2 c data b o t t o m t o p 1 abcde f hj kl mnprs t uvwxyz aa ab 23456789 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 top side 1-24
e e u u r r o o p p e e astec house, waterfront business park merry hill, dudley west midlands, dy5 1lx, uk telephone: 44 (1384) 842-211 facsimile: 44 (1384) 843-355 a a m m e e r r i i c c a a s s 5810 van allen way carlsbad, ca 92008 telephone: 760-930-4600 facsimile: 760-930-0698 155 www.astecpower.com asia units 2111-2116, level 21 tower1, metroplaza 223, hing fong road fwai fong, new territories hong kong telephone: 852-2437-9662 facsimile: 852-2402-4426 a c c c o r d : (north america) for all other countries, please contact factory. 1 ) quail electronics series 5050 or equivalent (15a/125v) supply end - nema 5-15p equipment end - iec 60320-c19 2 ) quail electronics series 5052 or equivalent (20a/125v) supply end - nema 5-20p equipment end - iec60320-c19 b l a n k p p a n e l : astec p/n 73-686-000 hps35 series drawings h h p p r r 1 1 -0 0 0 0 system max. size max. system module standard unit code (h x w x l) power distribution size weight (lbs.) hpr1 1.75" x 19.0" x 13.0" 1400 w (4 ea) hps35 1u 8.6 racks watts 1400 (fully populated) input voltage 90-264 module used hps35 rack id hpr1 code volts output amps l 12.0 116.8 w 48.0 29.2 hpr1 - standard options 00 = no options 01 = local sense 330.2 343.2 13.4 468.8 442.0 31.7 43.7 482.6 25.0 22.0 date: yyww s/n: mmmmwwssssrrc made in philippines rev: xx a/c code: xxxx 73-810-002 serial no.: maximum output power is 1400w input: 90 - 240vac - 40a 50/60 hz output: +12v / 29a hpr1-00 + rtn + rtn
p p i i n n 2 2 + + r r e e m m o o t t e e s s e e n n s s e e p p i i n n 3 3 - r r e e m m o o t t e e s s e e n n s s e e compensates for up to 0.5v drop. recommended shielded twisted wire pair. p p i i n n 1 1 2 2 - g g l l o o b b a a l l a a c c o o k k (out signal) note: ac ok signals are or'ed together internally. if any module fails, the led on the affected module will be off and the logic signal will indicate ac not ok. p p i i n n 1 1 9 9 - g g l l o o b b a a l l i i n n h h i i b b i i t t (in signal) note: all outputs disabled when pin 19 is open or high. p p i i n n 2 2 2 2 - s s w w p p (in/out signal) swp pin is used when connecting racks in parallel to achieve current sharing. current share accuracy is typically 10% of full load. note: swp voltage is 5v at 100% load current. m m o o d d u u l l e e i i n n h h i i b b i i t t (in signal) note: module inhibit signals for each slot in the rack is accessible in the d-sub connector (j18). refer to connector pin- out table for pin assignments. pin 1 is the return pin. north america (usa): 1-888-41-astec europe (uk): 44 (1384) 842-211 asia (hk): 852-2437-9662 156 rev 02.24.05 h h p p r r 1 1 -0 0 0 0 d-sub connector pin outs pin description 1 5v return (std-by) 2 + remote sense 3 - remote sense 4 5v stand by 5 unused 6 module inhibit 7 dc ok 8 ac ok 9 i2c_add#1 10 i2c_add#2 11 fan monitor 12 global ac ok 13 module inhibit 14 dc ok 15 ac ok 16 i2c_add#1 17 i2c_add#2 18 fan monitor 19 global inhibit d d c c o o k k (out signal) note: dc ok signals for each slot in the rack is accessible in the d-sub connector (j18). refer to connector pin-out table for pin assignments. pin 1 is the return pin. a a c c o o k k (out signal) note: ac ok signals for each slot in the rack is accessible in the d-sub connector (j18). refer to connector pin-out table for pin assignments. pin 1 is the return pin. hi state: source 100ua @ 4v low state: sink 10ma @ 0.5v f f a a n n m m o o n n i i t t o o r r (out signal) note: fan monitor signals for each slot in the rack is accessible in the d-sub connector (j18). refer to connector pin-out table for pin assignments. pin 1 is the return pin. i2c_add#1 i2c_add#2 tbd p s u c c o n n e c t o r 617-a-037-p-aj-1-21 (male socket) amphenol pin out diagram d-sub connector (male) m a t i n g c c o n n e c t o r 617-a-037-s-aj-1-20 (female socket) amphenol pin out diagram d-sub connector (female) s l o t 1 pin description 20 i2c clock 21 i2c data 22 swp 23 unused (i2c_int) 24 module inhibit 25 dc ok 26 ac ok 27 i2c_add#1 28 i2c_add#2 29 fan monitor 30 unused 31 module inhibit 32 dc ok 33 ac ok 34 i2c_add#1 35 i2c_add#2 36 fan monitor 37 unused s l o t 2 s l o t 3 s l o t 4
|
