led-converter unit ps-ld0602-x-yyy(s) (3 w) power systems ? the power solution web: www.power-systems.de address: hauptstr. 48 ; 74360 ilsfeld-auenstein / germany email: info@power-systems.de tel. : + 49 / 70 62 / 67 59 - 6 fax: + 49 / 70 62 / 67 59 - 800 all specifications are subject to change without not ice. page (1) version 1.2.2, 20th august 2009 (preliminary information) description : this low profile led-converter is developed for max. 6 led-lines applicable: 1~6 led lines (serial mode) pout max. 0,9 watt per line, total max. 3 watt led voltage max. 35v lamp current max. 35 madc per line features : internal open led detection for every line voltage or ext. pwm dimming 1000:1 dimming ratio with external pwm remote on / off wide input voltage range rohs compliant (s) temperature & humidity : operating temperatur e range -20c ~ +70c storage temperature range -20c ~ +85c humidity 95 %rh max dimensions : l x w x h 64 x 32 x 6.5 mm weight :5 (g) typ. connector style pin-terminal style components no. part description qty. material note 1 pcb 1 ul94v-0 (fr-4 or cem-3) t=1.0mm 2 connector cn1 1 53261-0890 molex 3 connector cn3 1 53261-0790 molex pin terminal length may differ
led-converter unit ps-ld0602-x-yyy(s) (3 w) power systems ? the power solution web: www.power-systems.de address: hauptstr. 48 ; 74360 ilsfeld-auenstein / germany email: info@power-systems.de tel. : + 49 / 70 62 / 67 59 - 6 fax: + 49 / 70 62 / 67 59 - 800 all specifications are subject to change without not ice. page (2) version 1.2.2, 20th august 2009 (preliminary information) electrical characteristics : output current select control jumper jp 1 jp 2 jp 3 jp 4 jp 5 output current break +1 ma break +2 ma break +4 ma break +8 ma break +5 ma example: 10ma (output current min.) + 1ma (jp1) = 11ma 10ma (output current min.) + 8ma (jp4) = 18ma jp1 ~ jp5 open = 30ma for more information, please visit our web-site. derating: 1 1,2 1,4 1,6 1,8 2 2,2 2,4 2,6 2,8 3 3,2 3,4 50 55 60 65 70 75 80 ambient temp. output wat t dc 5v input dc 12v input output side cn3 / cn4 pin no. symbols ratings cn3 / 4-1 rtn1 (-) led line 6 return cn3 / 4-2 rtn2 (-) led line 5 return cn3 / 4-3 rtn3 (-) led line 4 return cn3 / 4-4 rtn4 (-) led line 3 return cn3 / 4-5 rtn5 (-) led line 2 return cn3 / 4-6 rtn6 (-) led line 1 return cn3 / 4-7 vhigh (+) max 30vdc (max.30madc) input side cn1/cn2: pin no. sym bols ratings cn 1-1 vin 4.75 ~ 13.2 vdc cn 1-2 vin 4.75 ~ 13.2 vdc cn 1-3 vrmt 0 ~ 0.8 = off / 2.5 ~ vin = on cn 1-4 ext. pwm 0 ~ 0.5 = low / 2.5 ~ 5 = high cn 1-5 vbr 0.0 ~ 5.0 (5v=low brightness) cn 1-6 gnd - cn 1-7 gnd - cn 1-8 gnd - vin (v) vbr (v) tu (c) min. typ. max. output current iout 4.75 ~ 13.2 0 -20~+70 8 10 12 madc duty 100% , max current output current imin 4.75 ~ 13.2 5 -20~+70 - 10 - % duty cycle input current iin 4.75 ~ 13.2 0 -20~+70 0.06 - 0.3 adc open load shutdown vbias 4.75 ~ 13.2 0 -20~+70 - 35 - vdc pwm frequency f(pwm) 4.75 ~ 13.2 0 -20~+70 150 - 300 hz output power pout 4.75 ~ 13.2 0 -20~+70 tbd 3 tbd watt t u: - 2 0 ~+50 d eg c output power pout 4.75 ~ 13.2 0 -20~+70 tbd 1.9 tbd watt t u: - 2 0 ~+70 d eg c output power pout 4.75 ~ 13.2 0 -20~+50 tbd 0.9 tbd watt fo r o ne line output power pout 4.75 ~ 13.2 0 -20~+70 tbd 0.6 tbd watt fo r o ne line unit note parameters symbols conditions specification
led-converter unit ps-ld0602-x-yyy(s) (3 w) power systems ? the power solution web: www.power-systems.de address: hauptstr. 48 ; 74360 ilsfeld-auenstein / germany email: info@power-systems.de tel. : + 49 / 70 62 / 67 59 - 6 fax: + 49 / 70 62 / 67 59 - 800 all specifications are subject to change without not ice. page (3) version 1.2.2, 20th august 2009 (preliminary information) order key : ps-ld0602 -x -yyy with order of this converter please give the following key: -x to be replaced by: -1 for connectors -2 for pin-terminal in case of quantity orders (300+ p cs), a pre-configuration can be ordered: -yyy to be replaced by: three digit value for required output current per led line (from 010 to 030 including) attention: * if no value is mentioned, 10 ma output cu rrent per led line will be set as default * a selection of incorrect led current ma y decrease lifetime or destroy the backlight * orders for pre-configured converters can?t be cancelled examples: ps-ld0602 -1 -015 (s) 15 ma output current pcb with connectors ps-ld0602 -2 -025 (s) 25 ma output current pcb with pin-terminal test circuit : connect vbr to ground while using ext. pwm dimming. cables : for input: 500 mm, stripped and tinned ends, order key for output: 500 mm, stripped and tinned ends, order key note 1 : do not use analog dimming function and external pwm for dimming at the same time. note 2 : pin terminal style converters have molex connectors mounted. note 3 : above output current is the default value. corr ect output current is to be selected by user and under his sole responsibility. exceeding currents will damage the led backlight. note 4 : external pwm-signal is low active. note 5: do not use output 1 in case you connec t only 5 (or less) outputs. examples: use 5 outputs only 1 then connect pin 2+3+4+5+6. note 6 : in case customer do not connect all output, please ask factory. do not connect ext. pwm dimming while using vbr.
We use cookies to deliver the best possible
web experience and assist with our advertising efforts. By continuing to use
this site, you consent to the use of cookies. For more information on
cookies, please take a look at our Privacy Policy.
