www.rfm.com e-mail: info@rfm.com page 1 of 3 ?2009-2010 by rf monolithics, inc. XVT9005 - 2/2/10 electrical characteristics characteristic sym notes minimum typical maximum units nominal frequency fo 32.000000 mhz storagetemperature range -55 +125 c operating temperature range -30 +85 c power supply voltage vcc 2.8 v output voltage with load 10 pf || 10 k ? vout 0.8 vp-p output waveform clipped sinewave power supply current icc 2.0 ma control voltage vcon 1.41.0 v control voltage terminal input impedance 100k ohms frequency tolerance after reflow, vcon = 1.5 v 1.0 ppm max @ 25 c 3 c frequency stability ppm versus temperature, -30 to +85 c 2.0 versus supply voltage, 2.8 v 5% 0.3 versus load variation, 10 pf || 10 k ? 10% 0.2 aging 1 ppm frequency control range, vcon = 1.41.0 v 10 ppm start up time, 90% of final rf level in vp-p 2.0 ms harmonics -5.0 dbc ssb phase noise @ 10 khz carrier offset -130 dbc/hz max stanard shipping quantity on 180 mm (7?) reel 1000 units lid symbolization 9005 // ywws sm3225-4 case ? voltage controlled temperature compensated crystal oscillator application: wireless communication devices excellent frequency stability & low phase noise 3.2 x 2.5 x 1.3 mm surface-mount case complies with directive 2002/95/ec (rohs) 32 mhz vctcxo XVT9005 caution: electrostatic sensitive device. observe precautions for handling. notes: 1. the design, manufacturing process, and specifications of this device are subject to change without notice. pb preliminary
www.rfm.com e-mail: info@rfm.com page 2 of 3 ?2009-2010 by rf monolithics, inc. XVT9005 - 2/2/10 3.2 0.2 2 . 5 0 . 2 1.3 (max) 0.79 0 . 7 9 1.5 0 . 8 0.79 0 . 7 9 0 . 8 1.5 1 2 3 4 pin connection 1 vcon 2 gnd/case gnd 3 output 4vcc 4-terminal surface-mount seam weld case 3.2 x 2.5 mm nominal footprint sm3225-4 case application circuit
dimensions in mm
www.rfm.com e-mail: info@rfm.com page 3 of 3 ?2009-2010 by rf monolithics, inc. XVT9005 - 2/2/10 reel dimensions tape dimensions mm a0 b0 w f e p0 p1 p2 d1 d k0 t dimension 2.80 3.71 8.00 3.50 1.75 4.00 4.00 2.00 1.50 1.00 1.75 0.25 tolerance 0.10 0.10 +0.30/-0.10 0.05 0.10 0.10 0.10 0.05 +0.10/-0.00 +0.25/-0.00 0.10 0.02 mm a b c d e f g h t1 t2 t3 dimension 180 60 13.0 2.0 9.1 2.9 4.9 3.9 9.0 11.4 1.2 tolerance 1.0 +1.0/-0.0 0.2 0.5 0.5 0.5 0.5 0.5 0.3 1.0 0.1
|
