superworld electronics (s) pte ltd pg. 1 23.09.2010 note : specifications subject to change without notice. please check our website for latest information. 2. configuration & dimensions : 3. materials : (a) core : ferrite (b) wire : polyurethane enamelled copper wire (c) terminal clip : c5191 (f) s p i 3 0 2 0 - 1 r 5 n z f - (d)(e) (b) (c) (a) 1. part no. expression : (c) inductance code : 1r5 = 1.5uh (a) series code (b) dimension code (g) 11 ~ 99 : internal controlled number (f) f : rohs compliant 1.4 1.6 2.0 max. a b c 2.1 typ de 0.76 typ 3.00.3 3.00.2 unit:m/m (e) z : standard part (d) adhesive : epoxy recommended pcb pattern 3.4 1.2 typ fg 0.7 typ (e) ink : 70000 -00101 smd power inductors (preliminary) spi3020 series 0.6 3.3 3.2 or a b e d e c e marking f (d) tolerance code : m = 20%, n = 30% (g)
superworld electronics (s) pte ltd pg. 2 23.09.2010 note : specifications subject to change without notice. please check our website for latest information. 5. electrical characteristics : 4. general specification : f) resistance to solder heat : 260c 10secs e) operating temp. : -40c to +105c ( include self temp. rise ) d) storage temp. : -40c to +105c b) idc2 : based on temperature rise ( ? t: 40c typ.) a) idc1 : based on inductance change ( ? l/lo: <30%) @ ambient temp. 25c part no. spi3020-1r5nzf- inductance 1.530% ( uh ) idc1 ( m
) 0.1v/100k 64 1.80 ( a ) rdc idc2 1.70 ( a ) ( hz ) frequency test 20% 0.1v/100k 87 2.230% 0.1v/100k 100 spi3020-2r2nzf- 1.45 1.30 1.40 1.20 smd power inductors (preliminary) spi3020 series spi3020-3r3nzf- 3.330% 0.1v/100k 150 1.00 1.15 4.720% 0.1v/100k 180 0.1v/100k 240 spi3020-4r7mzf- 1.05 0.85 0.87 0.60 spi3020-6r8mzf- 6.820% 0.1v/100k 1410 0.32 0.35 1020% 0.1v/100k 1640 spi3020-100mzf- 0.30 0.27 4720% spi3020-470mzf- c) rated current : idc1 or idc2, whichever value is lower marking c e g i k m u w 6820% spi3020-680mzf-
superworld electronics (s) pte ltd pg. 3 6. reliability & test condition : resistance to soldering heat vibration substrate bending item (a total of 6 hours) the condition shown in the above profile for 1 time. 130~150c and after it has been immersed to a depth 0.5mm with new solder smoothly when the sample is taken out of the specimen shall be stored at standard atmospheric conditions for 1 hour, after which the measurement shall there shall be no damage or problems. the specimen shall be passed through the reflow oven with the solder bath. more than 90% of the electrode sections shall be cowered a temperature of 2455c. below for 30.2 seconds fully in molten solder m705 with then be preheated for about 2 minutes in a temperature of flux (rosin, isopropyl alcohol{jis-k-1522}) shall be coated over the whole of the sample before hard, the sample shall be applied to the 3 directions (x,y,z) for 2 hours each. a frequency of from 10 to 55hz/1 minute repeated should there shall be no mechanical damage. ? l/lo<10% there shall be no mechanical damage or the sample shall be soldered onto the printed circuit board and when a vibration having an amplitude of 1.52mm and performance test condition electrical damage. the sample shall be soldered onto the printed circuit board in figure 1 and a load applied until the figure in the arrow direction is made approximately 3mm.(keep time 30 secs) pressure rod figure-1 solderability new solder mechanical (reflow soldering) be made. 100 40 2 20 50 20 30 30 20 t = 1.6 ?4.5 452 452 20 10 r5 r340 bending test board ? l/lo<10% 23.09.2010 300 250 200 150 100 50 2 min. 10 sec 2 min. or more 150~ 180c 30 sec min. (230c max.) soldering (peak temperature 2603c 10sec) slow cooling (stored at room temperature) pre-heating soldering temperature (c) note : specifications subject to change without notice. please check our website for latest information. smd power inductors (preliminary) spi3020 series more than 90%
superworld electronics (s) pte ltd pg. 4 6. reliability & test condition : temperature characteristics dielectric withstand voltage item the sample shall be left for 964 hours in an atmosphere the sample has been left in a normal temperature and with a temperature of -253c. upon completion of the test, the measurement shall be normal humidity for 1 hour. upon completion of the measurement shall be made after the sample shall be left for 964 hours in an atmosphere with a temperature of 852c and a normal humidity. temperature and normal humidity shall be ? l/l20c<10%. calculated based on the value applicable in a normal 0~2000 ppm/c ? l/l20c<10% the test shall be performed after the sample has stabilized in an ambient temperature of -20 to +85c,and the value performance test condition ac 100v voltage shall be applied for 1 minute across the top surface and the terminal of this sample high temperature storage electrical characteristics test made after the sample has been left in a normal temperature there shall be no damage or problems. there shall be no mechanical damage. there shall be no mechanical damage. and normal humidity for 1 hour. change of temperature moisture storage there shall be no other damage of problems there shall be no mechanical damage. the sample shall be subject to 5 continuous cycles, such as shown in the table 2 below and then it shall be subjected to standard atmospheric conditions for 1 hour, after which measurement shall be made. duration 852c 4 2 3 1 (thermostat no.1) 5 sec. or less -253c temperature 30 min. no.1 : no.2 5 sec. or less no.2 : no.1 30 min. (thermostat no.2) standard atmospheric standard atmospheric the sample shall be left for 964 hours in a temperature of 402c and a humidity(rh) of 90~95%. upon completion of the test, the measurement shall be made after the sample has been left in a normal temperature and normal humidity more than 1 hour. ? l/lo<10% 23.09.2010 ? l/lo<10% low temperature storage ? l/lo<10% ? l/lo<10% note : specifications subject to change without notice. please check our website for latest information. smd power inductors (preliminary) spi3020 series
superworld electronics (s) pte ltd pg. 5 smd power inductors (preliminary) 23.09.2010 spi3020 series note : specifications subject to change without notice. please check our website for latest information. 7. packaging information : 7-1. reel dimension (mm) 100 18 2.2 7-2 carrier tape dimensions (mm) 17.3 13.2 330 13 120 7-3 taping dimensions (mm) 12mm w 3.2mm 3.5mm 2.4mm ao ko bo t p 0.3mm 8.0mm 7-4 quantity 3000pcs/reel the products are packaged so that no damage will be sustained. 8mm 4 mm start end leader no component 200mm min. components trailer no component 400mm min. user direction of feed t 4.00 2.000.05 ao p a a ko w 5.50 1.75 ?1.5+0.1/-0.0 1.5 bo e e e e
|