TX-704-0007-12M800000 tcxo www.vectron.com modified 2011-04-07 index : 1 printed 2011-06-03 ? page 1 of 4 vectron international ? product specifications tx-704-0007 nominal frequency (f0) 12 . 8 mhz frequency stabilities parameter frequency stability operating temp . range over all ( df / f 0 ) - 4 . 6 to 4 . 6 ppm vs . operating temp . range ( df / f @ 25 c ) - 0 . 28 to 0 . 28 ppm - 40 ... 85 c additional information temperature slope max : 0 . 2 ppm / c parameter value condition initial tolerance ( df / f 0 ) - 1 to 1 ppm @ 25 c vs . supply voltage change ( df / f ) - 0 . 2 to 0 . 2 ppm static ; 3 . 3 v 5 % vs . load change ( df / f ) - 0 . 2 to 0 . 2 ppm static ; load 10 % vs . aging / 20 years ( df / f ) < 2 . 5 ppm @ 40 c holdover 24 h 0 . 32 ppm incl . temp . stab . - 40 ...+ 85 c overall incl .: initial , temp .- 40 ..+ 85 c , supply , load var . and aging 20 years rf output parameter value condition signal lvcmos load 15 pf 10 % fan out 3 rise time < 5 ns @ 10 to 90 % vout fall time < 5 ns @ 90 to 10 % vout duty cycle 40 / 60 % @ 1 . 65 v v low x < 0 . 3 v v high x > 3 v enable function enable function output pin 8 pin 5 high data open data low high tristate supply voltage parameter value condition supply voltage ( vs ) 3 . 3 v 5 % current consumption steady state < 6 ma @ vsnom & 25 c additional parameters parameter typ . max . condition phase noise - 97 dbc / hz @ 10 hz - 118 dbc / hz @ 100 hz - 140 dbc / hz @ 1000 hz - 152 dbc / hz @ 10 khz - 153 dbc / hz @ 100 khz - 153 dbc / hz @ 1000 khz parameter value condition start - up time < 10 ms additional information this smd oscillator is designed only for pick and place / reflow soldering process . manual soldering may damage the part and therefore not recommended for the mounting of this oscillator . processing & packing handling & processing note additional environmental conditions sealing test a nicht dicht ( not hermetically sealed ) solderability j _ std _ 002 b cond a leaded / cond . b smd 245 c ( diving time 5 0 . 5 s ) dip + look with 8 h damp treatment : solder wetting > 95 %
TX-704-0007-12M800000 tcxo www.vectron.com modified 2011-04-07 index : 1 printed 2011-06-03 ? page 2 of 4 vectron international ? product specifications tx-704-0007 absolute maximum ratings parameter min typ max units condition operable temperature range - 40 85 c storage temperature range - 55 125 c enclosure type g 290 height 1 . 8 mm all units in mm pin connections pin 1 : i . c . 2 : n . c . pin 3 : i . c . 4 : gnd pin 5 : rf - output 6 : n . c . pin 7 : n . c . 8 : enable pin 9 : v _ supply 10 : n . c . marking tx - 007 12 m 800 * vayyww - - * pin - 1 marking
TX-704-0007-12M800000 tcxo www.vectron.com modified 2011-04-07 index : 1 printed 2011-06-03 ? page 3 of 4 vectron international ? product specifications tx-704-0007 reflow profile profile feature pb - free assembly / sn - pb assembly average ramp - up rate ( tl to tp ) 3 c / second max . preheat - temperature min ( tsmin ) 150 c - temperature min ( tsmax ) 200 c - time ( min to max ) ( ts ) 60 - 180 seconds tsmax to tl - ramp - up rate 3 c / second max . time maintainted above - temperature ( tl ) 217 c - time ( tl ) 60 - 150 seconds peak temperature ( tp ) max 260 c time within 5 c of actual peak temperature ( tp ) 20 - 40 seconds ramp - down rate 6 c / second max . time 25 c to peak temperature 8 minutes max . note : all temperatures refer to topside of the package , measured on the package body surface . additional information this smd oscillator has been designed for pick and place reflow soldering .
TX-704-0007-12M800000 tcxo www.vectron.com modified 2011-04-07 index : 1 printed 2011-06-03 ? page 4 of 4 vectron international ? product specifications tx-704-0007 standard shipping method tape width w [ mm ] quantity per meter quantity per reel p [ mm ] a [ mm ] b [ mm ] k [ mm ] 16 125 750 8 5 . 4 7 . 4 2 . 7 notes: unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25c). subject to technical modification.
|