non-operating/storage temperture rating: -40c to 8 5c tri-loc body: .000100 min nickel per ams-qq-n-290 humidity: <95 rh (at 40c) operating temperature rating: -40c to 75c 5. environmental: aux electrical contacts: 600 vac, 10 amp low voltage contacts: 42 - 60 vac, 1 amp 4. electrical specifications: copper flash per astm b73 4 (rohs) crimp sleeve: .000100 min nickel per ams-qq-n-290 o ver .000080 min nickel per ams-qqn -290 (rohs) contacts: .000100 min gold per astm b488 over over copper flash per a stm b734 (rohs) catalog p/n: 7765-4-3 notes: unless otherwise specified 1. interface compliant to smpte 304 specificat ion. 2. material specifications: contacts and tri-loc body: copper alloy alignment pins: brass per astm b16 crimp sleeve: phos. bronze o-rings and strain relief: silicone rubber all plastic parts: 20% glass filled polypropylene all other metal parts: 303 stainless steel per astm a582 3. finish specifications: stainless steel parts: passivate 6. optical: wavelength: 1100nm - 1350nm insertion loss: 0.3db typical, 0.5db max return loss: > -45db, -50db typical 7. replacement kits: contact kit: 7760-000-00708z contact kit with cartridge: 7760-000-00710z 8. cable preparation and stripping procedure: cap-e05. 9. optional environmental boot 7760-000-00704 z sold separately. 10. red ldpe dust cap included (not shown) 11. crimp tooling: for factory application use hand tool kth-1000 and die kth-2035 for field application use hand tool kth-5000 and di e kth-5018 62 barnes industrial road north angle .xxxx [x.xxx] .xxxx wallingford, connecticut 06492 xxx kfc date 01/07/10 by per er30231 description 05 rev xx/xx/xx xxx date approved xx/xx/xx xxx date approved 04/07/10 wpm date approved 04/06/10 psm date appd revised drawing drawn .xxx [x.xx] .005 [0.13] customer angles: 2 scale: 1:1 sales drawing per asme y14.5m-1994 unless otherwise specified: dimensions are in inches [mm] tolerances: decimal: .xx [x.x] .01 [0.3] winchester electronics corporation third dmf026 b 1 2 a 05 pre-polished sht rev of tri-loc, smpte 304, plug sd7765-4-3 .915 23.24 9/16" wrench flats (180 apart) 3/4" wrench flats (180 apart) mark: 7765-4-3 (date code) 5.051 128.30 .804 20.42
catalog p/n: 7765-4-3 item no. part no. description new ferrule design/qty. plating code(s) 14 vnfps01-900-34 splice protector sleeve, 34mm 50 13 vnsc-3-4u red ldpe dust cap, .750" id 25 12 7760-000-00711z fiber optic connector stub 2 11 78-0705u rear o-ring 25 10 78-1012U strength member support clamp 10 9 78-3013u plug insulator half side "a" 25 8 78-3012u plgu insulator half side "b" 25 7 78-0102u #4-40 hex set screw 10 6 1-8156u crimp sleeve (cable shield ferrule) 25 5 78-4006u plug female crimp contact 50 4 78-4005u plug male crimp contact 50 3 78-7003u plug cartridge assembly 10 2 78-0301u washer for rear cable seal 25 1 78-0701u rear cable seal 25 xxx kfc 01/07/11 by date appd revised drawing per er30231 description 05 rev xx/xx/xx xxx date approved xx/xx/xx xxx date approved 04/07/10 wpm date approved 04/06/10 psm date drawn customer sales drawing per asme y14.5m-1994 unless otherwise specified: dimensions are in inches [mm] tolerances: decimal: .xx [x.x] .01 [0.3] .xxx [x.xx] .005 [0.13] .xxxx [x.xxx] .xxxx angles: 2 scale: 1:1 winchester electronics corporation 62 barnes industrial road north wallingford, connecticut 06492 third angle dmf026 b a tri-loc, smpte 304, plug pre-polished sht rev of 05 2 2 sd7765-4-3 2 1 11 6 10 7 9 3 13 8 4 5 14 12 replacement component ordering numbers
|