scale from do not this print .0723 (see note 14) .0923 (see note 14) .0775 (4 plcs) (measured at base of tower) ((no of positions -1) x .100) .078 .010 .08 gate pads (see note 9) fig. 1 ipd1-06-s shown c l revision l e - m a i l : i n f o @ s a m t e c . c o m c o d e : 5 5 3 2 2 sheet of 15. all dimensions to be symmetric about centerline within .0015 dimensions are in inches. tolerances are: decimals angles confidential and proprietary to unless otherwise specified, this document contains information unless otherwise stated. 16. option not for sale. for retention latch feature , see ipd1-xx-s-m print. or transferred to other documents or .xx: samtec, inc. and shall not be reproduced .0015 [.038] material: .100 shrouded contact body by: ipd1-xx-s-x-x dwg. no. description: proprietary note .xxxx: .003 [.08] .xxx: .01 [.3] 2 consent of samtec, inc. d o n o t s c a l e d r a w i n g dean p 04/25/2005 3 1 s h e e t s c a l e : 2 : 1 zytel 103fhs, color: white f:\dwg\misc\mktg\ipd1-xx-s-x-x-mkt.slddrw max regrind: 25% obtained without the expressed written max gate vestige: .002 max flash allowed: .004 purpose other than that which it was disclosed to others or used for any notes: 1. represents a critical dimension. 2. samtec logo shall appear at one location on surface shown, approximately .150 x .094 (both sides). 3. all multiple cavity molds shall identify each cavity with a letter designation located where shown. 4. all identification marks must not stand greater than .002 off the surface of the part. 5. molded surfaces shall be consistent and smooth. surfaces to be free of scatches, nicks, sink areas, voids or other blemishes. 6. max allowable bow: see table 1. bow to be measured at midline of part. 7. part to be symmetric about the centerline within +/-.002, unless otherwise stated. 8. number of positions (per row) to be shown in this area excluding 2, 3 and 4 positions. size and depth similar to position 1 indicator. 9. gate pads must be recessed .005. 10. end cores are polarized. confirm geometry relative to position 1 indicator & gate pads. 11. position 1 indicator to be .0005 max depth, not present on 2-4 position options. 12. specified positions to be identified where shown (note 4 applies). 13. mold designer has discretion over rib location. steel print setup sheet must show rib configuration for each part number. 14. part must draft inward from bottom to top of stack. 5 2 0 p a r k e a s t b l v d , n e w a l b a n y , i n 4 7 1 5 0 p h o n e : 8 1 2 - 9 4 4 - 6 7 3 3 f a x : 8 1 2 - 9 4 8 - 5 0 4 7 alt material: zytel 101f, color: white option ipd1-xx-s-x-x no of positions -k: keyed polarization [see fig. 2 for -02 position] (per row) -s: single row specification option (see figure 3, sheet 2) -02 thru -25 -r: retention latch (see note 16) (see sheet 3) section "a"-"a" c5 see note 2 see note 3 see note 8 c6 'd' 'h' .4800 .255 . 0 0 2 + .0020 .059 - . 0 0 1 .100 .005 "b" "b" 03 01 05 06 04 see note 12 02 'g' .050 (typ) .050 .020 (2 plcs) section "b"-"b" parting line 'f' 'e' .112 .045 .082 c3 c4 .002 .003 'a' 'b' 'c' .200 .300 .002 .050 (typ) "a" "a" c1 c2 see note 11 .007 .003 .220 - ((no of positions x .100) + .055) .050 .010 .035 . 0 0 3 + . 0 0 5 .505 - . 0 0 0 + . 0 0 6 n o o f p o s t / b b o w s / s b o w - 0 2 t h r u - 1 0 . 0 0 2 . 0 0 2 - 1 1 t h r u - 2 5 . 0 0 3 . 0 0 3 t a b l e 1
.068 .1300 30 c8 scale 3 : 1 detail 'a' c7 .060 .075 .002 .145 .002 .035 .085 .145 .225 .005 r .025 c9 scale 5 : 1 detail 'b' c10 .0800 (typ) .100 (typ) detail 'n' scale 10 : 1 .0108 .0110 .0030 detail 'c' scale 5 : 1 c11 'n' .0400 (typ) .100 ref .0310 sq (typ) detail 'g' scale 5 : 1 .0895 - . 0 0 0 0 + . 0 0 3 0 (typ) .0750 - . 0 0 0 + . 0 0 3 (typ) .0850 - . 0 0 2 + . 0 0 3 (typ) fig. 3 -k: keyed polarization (ipd1-06-s-k shown) (same as fig. 1, unless otherwise stated) fig. 2 -02 position (same as fig. 1, unless otherwise stated) .325 detail 'h' scale 12 : 1 .020 (typ) .006 (typ) detail 'd' scale 5 : 1 18 - 2 + 5 (typ) .0200 (typ) .0187 15 - 4 + 2 (typ) "n" "n" section "n"-"n" scale 4 : 1 .0300 2 .020 scale 4 : 1 detail 'f' c14 max flash .006 this area only .030 .076 .110 - . 0 0 3 + . 0 0 0 34 .4550 .250 r .025 (typ) .041 .005 .015 20 .105 - . 0 0 3 + . 0 0 1 .200 c13 scale 8 : 1 detail 'e' c12 .0100 .0690 - . 0 0 1 + . 0 0 2 2 ref 30 (typ) .0020 .0250 .0100 .0735 15 (typ) .0159 sheet of .100 shrouded contact body by: ipd1-xx-s-x-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. d o n o t s c a l e d r a w i n g dean p 04/25/2005 3 2 s h e e t s c a l e : 2 : 1 revision l f:\dwg\misc\mktg\ipd1-xx-s-x-x-mkt.slddrw 5 2 0 p a r k e a s t b l v d , n e w a l b a n y , i n 4 7 1 5 0 p h o n e : 8 1 2 - 9 4 4 - 6 7 3 3 f a x : 8 1 2 - 9 4 8 - 5 0 4 7 e - m a i l : i n f o @ s a m t e c . c o m c o d e : 5 5 3 2 2
fig. 4 ( ipd1-06-s-r shown) (same as fig.1, unless otherwise stated) (see note 16) not released for production fig. 5 ( ipd1-02-s-r shown) (same as fig.2, unless otherwise stated) (see note 16) not released for production 'm' .230 .126 .1700 "j" "j" sheet of .100 shrouded contact body by: ipd1-xx-s-x-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. d o n o t s c a l e d r a w i n g dean p 04/25/2005 3 3 s h e e t s c a l e : 4 : 1 revision l f:\dwg\misc\mktg\ipd1-xx-s-x-x-mkt.slddrw 5 2 0 p a r k e a s t b l v d , n e w a l b a n y , i n 4 7 1 5 0 p h o n e : 8 1 2 - 9 4 4 - 6 7 3 3 f a x : 8 1 2 - 9 4 8 - 5 0 4 7 e - m a i l : i n f o @ s a m t e c . c o m c o d e : 5 5 3 2 2 'l' .355 "k" "k" c15 scale 5 : 1 section "j"-"j" c16 .0170 .0010 .041 - . 0 0 1 + . 0 0 0 r .055 .0327 "a" (see table 2) .250 c18 scale 6 : 1 section "k"-"k" c17 c19 .0085 45 x .1600 .0010 .1700 .0010 .1800 .0010 .070 .065 .040 .035 detail 'l' scale 8 : 1 r .005 (typ) .0400 detail 'm' scale 6 : 1 .0015 n o o f p o s " a " -02 . 3 2 5 -03 . 4 2 5 t a b l e 2
|
