vishay general semiconductor tpsmp6.8 thru tpsmp43a new product document number 88937 15-feb-06 www.vishay.com 1 do-220aa (smp) high power density surface mount automotive transient voltage suppressors features ? very low profile - typical height of 1.0 mm ? ideal for automated placement ? unidirection only ? exclusive patented par oxide passivated chip construction ? excellent clamping capability ? low incremental surge resistance ? very fast response time ? meets msl level 1, per j-std-020c ? solder dip 260 c, 40 seconds ? component in accordance to rohs 2002/95/ec and weee 2002/96/ec typical applications protection for ics, drive transistors, signal lines of sensor units, and electronic units in consumer, computer, industrial and automotive applications. mechanical data case: do-220aa (smp) epoxy meets ul-94v-0 flammability rating terminals: matte tin plated leads, solderable per j-std-002b and jesd22-b102d e3 suffix for commercial grade, he3 suffix for high reliability grade (aec q101 qualified) polarity: color band denotes cathode end major ratings and characteristics v (br) 6.8 v to 43 v p ppm (for v (br) 6.8 v) 250 w p ppm (for v (br) 7.5 v - 12 v) 300 w p ppm (for v (br) 13 v - 43 v) 400 w p d 1.0 w i fsm 40 a t j max. 185 c note: (1) non-repetitive current pulse, per fig. 3 and derated above t a = 25 c per fig. 2 (2) mounted on p.c.b. with 5.0 x 5.0 mm copper pads attached to each terminal (3) pulse test: 300 s pulse width, 1 % duty cycle maximum ratings (t a = 25 c, unless otherwise specified) parameter symbol value unit peak power dissipation with a 10/1000 s waveform (1)(2) (fig. 1 & 3) p ppm see table next page w peak power pulse current with a 10/1000 s waveform (1) (fig. 1) i ppm see table next page a power dissipation on in finite heatsink, t a = 50 c p d 1.0 w peak forward surge current 10 ms single half sine-wave superimposed on rated load i fsm 40 a maximum instantaneous forward voltage at 25 a (3) v f 2.5 v operating junction and storage temperature range t j , t stg - 65 to + 185 c
www.vishay.com 2 document number 88937 15-feb-06 vishay general semiconductor tpsmp6.8 thru tpsmp43a note: (1) v (br) measured after i t applied for 300 s, i t = square wave pulse or equivalent (2) surge current waveform per fig. 3 and derated per fig. 2 (3) all terms and symbols are consistent with ansi/ieee c62.35 electrical characteristics (t a = 25 c, unless otherwise specified) device type device marking code breakdow n voltage v (br) (1) at i t (v) test current i t (ma) stand- off voltage v wm (v) maximum reverse leakage at v wm i r (a) maximum reverse leakage at v wm t j = 150 c i d (a) maximum peak pulse surge current i ppm (2) (amps) maximum clamping voltage at i ppm v c (volts) maximum temperature coefficient of v (br) (%/c) min max tpsmp6.8 adp 6.12 7.48 10.0 5.50 300 1000 23.2 10.8 0.057 tpsmp6.8a aep 6.45 7.14 10.0 5.80 300 1000 23.8 10.5 0.057 tpsmp7.5 afp 6.75 8.25 10.0 6.05 150 500 25.6 11.7 0.060 tpsmp7.5a agp 7.13 7.88 10.0 6.40 150 500 26.5 11.3 0.061 tpsmp8.2 ahp 7.38 9.02 10.0 6.63 50.0 200 24.0 12.5 0.065 tpsmp8.2a akp 7.79 8.61 10.0 7.02 50.0 200 24.8 12.1 0.065 tpsmp9.1 alp 8.19 10.0 1.0 7.37 10.0 50.0 21.7 13.8 0.068 tpsmp9.1a amp 8.65 9.55 1.0 7.78 10.0 50.0 22.4 13.4 0.068 tpsmp10 anp 9.00 11.0 1.0 8.10 5.0 20.0 20.0 15.0 0.073 tpsmp10a app 9.50 10.5 1.0 8.55 5.0 20.0 20.7 14.5 0.073 tpsmp11 aqp 9.90 12.1 1.0 8.92 2.0 10.0 18.5 16.2 0.075 tpsmp11a arp 10.5 11.6 1.0 9.40 2.0 10.0 19.2 15.6 0.075 tpsmp12 asp 10.8 13.2 1.0 9.72 1.0 5.0 17.3 17.3 0.076 tpsmp12a atp 11.4 12.6 1.0 10.2 1.0 5.0 18.0 16.7 0.078 tpsmp13 aup 11.7 14.3 1.0 10.5 1.0 5.0 21.1 19.0 0.081 tpsmp13a avp 12.4 13.7 1.0 11.1 1.0 5.0 22.0 18.2 0.081 tpsmp15 awp 13.5 16.3 1.0 12.1 1.0 5.0 18.2 22.0 0.084 tpsmp15a axp 14.3 15.8 1.0 12.8 1.0 5.0 18.9 21.2 0.084 tpsmp16 ayp 14.4 17.6 1.0 12.9 1.0 5.0 17.0 23.5 0.086 tpsmp16a azp 15.2 16.8 1.0 13.6 1.0 5.0 17.8 22.5 0.086 tpsmp18 bdp 16.2 19.8 1.0 14.5 1.0 5.0 15.1 26.5 0.088 tpsmp18a bep 17.1 18.9 1.0 15.3 1.0 5.0 15.9 25.5 0.088 tpsmp20 bfp 18.0 22.0 1.0 16.2 1.0 5.0 13.7 29.1 0.090 tpsmp20a bgp 19.0 21.0 1.0 17.1 1.0 5.0 14.4 27.7 0.090 tpsmp22 bhp 19.8 24.2 1.0 17.8 1.0 5.0 12.5 31.9 0.092 tpsmp22a bkp 20.9 23.1 1.0 18.8 1.0 5.0 13.1 30.6 0.092 tpsmp24 blp 21.6 26.4 1.0 19.4 1.0 5.0 11.5 34.7 0.094 tpsmp24a bmp 22.8 25.2 1.0 20.5 1.0 5.0 12.0 33.2 0.094 tpsmp27 bnp 24.3 29.7 1.0 21.8 1.0 5.0 10.2 39.1 0.100 tpsmp27a bpp 25.7 28.4 1.0 23.1 1.0 5.0 10.7 37.5 0.096 tpsmp30 bqp 27.0 33.0 1.0 24.3 1.0 5.0 9.2 43.5 0.097 tpsmp30a brp 28.5 31.5 1.0 25.6 1.0 5.0 9.7 41.4 0.097 tpsmp33 bsp 29.7 36.3 1.0 26.8 1.0 5.0 8.4 47.7 0.098 tpsmp33a btp 31.4 34.7 1.0 28.2 1.0 5.0 8.8 45.7 0.098 tpsmp36 bup 32.4 39.6 1.0 29.1 1.0 5.0 7.7 52.0 0.099 tpsmp36a bvp 34.2 37.8 1.0 30.8 1.0 5.0 8.0 49.9 0.099 tpsmp39 bwp 35.1 42.9 1.0 31.6 1.0 5.0 7.1 56.4 0.100 tpsmp39a bxp 37.1 41.0 1.0 33.3 1.0 5.0 7.4 53.9 0.100 tpsmp43 byp 38.7 47.3 1.0 34.8 1.0 5.0 6.5 61.9 0.101 tpsmp43a bzp 40.9 45.2 1.0 36.8 1.0 5.0 6.7 59.3 0.101
document number 88937 15-feb-06 www.vishay.com 3 tpsmp6.8 thru tpsmp43a vishay general semiconductor ratings and characteristics curves (t a = 25 c unless otherwise specified) ordering information preferred p/n unit weight (g) preferred package code base quantity delivery mode tpsmp6.8a-e3/84a 0.024 84a 3000 7" diameter plastic tape & reel tpsmp6.8a-e3/85a 0.024 85a 10000 13" diameter plastic tape & reel figure 1. peak pulse power rating curve figure 2. pulse derating curve tpsmp13 - tpsmp43a tpsmp7.5 - tpsmp12a tpsmp6. 8 0.1 s 1.0 s 10 s 100 s 1.0 ms 10 ms 10 1.0 0.1 0.01 p ppm - peak po w er (k w ) td - p u lse w idth (s) 100 75 50 25 0 0 25 50 75 100 125 150 175 200 peak p u lse po w er (p pp ) or c u rrent (i pp ) derating in percentage ( % ) t j = initial temperat u re (c) figure 3. pulse waveform figure 4. typical junction capacitance 0 50 100 150 td 0 1.0 2.0 3.0 4.0 i ppm - peak p u lse c u rrent, % i rsm t - time (ms) tr = 10 sec peak v al u e i ppm half v al u e - i ppm ipp 2 10/1000 sec w a v eform as defined b y r.e.a. t j = 25 c p u lse w idth (td) is defined as the point w here the peak c u rrent decays to 50 % of i ppm c j ,j u nction capacitance, pf v (br) , breakdo w n v oltage ( v ) 10 100 1000 10000 1 10 100 200 meas u red at zero bias t j = 25 c f = 1 mhz v sig = 50 m v p-p meas u red at stand-off v oltage, v w m
www.vishay.com 4 document number 88937 15-feb-06 vishay general semiconductor tpsmp6.8 thru tpsmp43a package outline dimensions in inches (millimeters) figure 5. maximum peak forward surge current 40 35 30 25 20 15 10 5 0 1 10 100 peak for w ard s u rge c u rrent (a) nu m b er of cycles at 50 hz figure 6. maximum peak forward surge current 0 25 50 75 100 125 150 175 200 1.00 0.75 0.50 0.25 0 po w er dissipation ( w ) am b ient temperat u re, c 0.000 (0.00) 0.012 (0.30) 0.013 (0.35) 0.004 (0.10) 0.01 8 (0.45) 0.006 (0.15) 0.045 (1.15) 0.033 (0. 8 5) 0.036 (0.91) 0.024 (0.61) 0.016 (0.40) 0.032 (0. 8 0) 0.053 (1.35) 0.041 (1.05) 0.012 (0.30) ref 0.105 (2.67) 0.025 (0.635) 0.100 (2.54) 0.030 (0.762) 0.050 (1.27) cathode b and 0.142 (3.61) 0.126 (3.19) 0.15 8 (4.00) 0.146 (3.70) 0.0 8 6 (2.1 8 ) 0.074 (1. 88 ) 0.0 8 7 (2.20) 0.103 (2.60) do-220aa (smp)
legal disclaimer notice vishay document number: 91000 www.vishay.com revision: 08-apr-05 1 notice specifications of the products displayed herein are subjec t to change without notice. vishay intertechnology, inc., or anyone on its behalf, assume s no responsibility or liability fo r any errors or inaccuracies. information contained herein is intended to provide a product description only. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. except as provided in vishay's terms and conditions of sale for such products, vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and /or use of vishay products including liab ility or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyrigh t, or other intellectual property right. the products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify vishay for any damages resulting from such improper use or sale.
|
