size list 34 6.8 10 22 33 39 47 56 68 82 100 120 150 180 220 270 330 470 560 680 820 1200 1500 e12 f13 rv sv f 2.5 3.3 4 5.2 6.3 8.2 10 11.5 16 18.4 20 23.0 25 25.0 c6 c6 e7 e7 f8 e12 f8 f13 c6 e7 f8 e12 f13 c6 e7 f8 e12 f13 c6 e7 f8 e12 f13 c6 e7 e7 f8 f8 f8,e12 f13 c6 e7 f8 e12 f13 (unit : mm) t 1 in case of some problems for measured values, measure after applying rated voltage for 2.5 to 20v products or temperature derating voltage for 25v products for 120 minutes at 105 c . dimensions rv : rated voltage (sv) : surge (room temperature) t for the minimum packing quantity, please refer to page 51. this is a radial lead type using conductive polymer based on the svp series. because of its improved heat-proof characteristics, the rated ripple current values are guaranteed at 105 c . furthermore, there is no need to apply a temperature-compensating coefficient. lead free-flow is supported. marking : polarity( ), rated voltage, rated capacitance (purple) lot.no., sep specifications 4 q f d j g j d b u j p o t g p s f b d i t f s j f t 4 . specifications for each series d l f 15min. 19min. d 4min. 6.3 8.0 10.0 8.0 10.0 6.0 7.0 8.0 12.0 13.0 2.5 0.5 3.5 0.5 5.0 0.5 3.5 0.5 5.0 0.5 0.45 0.45 0.50 0.60 0.60 c6 e7 f8 e12 f13 size code d+0.5max. lmax. f d 0.05 conductive polymer type sep series standard radial lead type, guaranteed at 105 c for 3,000h items characteristics -55 c to +105 c m : 20% less than or equal to the value of table9 less than or equal to the value of table9 less than or equal to the value of table9 within 20% 1.5 times or less than an initial standard 1.5 times or less than an initial standard below an initial standard within 20% 1.5 times or less than an initial standard 1.5 times or less than an initial standard below an initial standard (after voltage processing) within 5% below an initial standard below an initial standard below an initial standard (after voltage processing) category temperature range tolerance on rated capacitance tangent of loss angle leakage current esr endurance damp heat (steady state) characteristics of impedance ratio at high temp. and low temp. -55 c +105 c ? c/c tan esr leakage current ? c/c tan esr leakage current ? c/c tan esr leakage current resistance to soldering heat z / z 20 c z / z 20 c 0.75 to 1.25 0.75 to 1.25 120hz 120hz 105 c, 3,000h, rated voltage applied (2.5v 2,000h), (25v 20v applied) 60 c, 90 to 95%rh, 1,000h, no-applied voltage flow method (260 5 c x 10s) t 1 conditions based the value at 100khz | +20 c after 2 minutes
35 c6 25sep6r8m 20sep22m 16sep39m 10sep56m 6sep82m 4sep100m 4sep150m 25sep10m 20sep33m 20sep47m 16sep82m 10sep120m 6sep150m 4sep220m 4sep330m 25sep22m 20sep56m 20sep68m 20sep100mx 16sep150m 10sep270m 6sep330m 4sep470m 4sep680m 25sep33m 20sep100m 16sep180m 10sep330m 6sep470m 4sep560m 2r5sep680m 25sep56m 20sep150m 16sep330m 10sep560m 6sep820m 4sep1200m 2r5sep1500m 25 20 16 10 6.3 4 4 25 20 20 16 10 6.3 4 4 25 20 20 20 16 10 6.3 4 4 25 20 16 10 6.3 4 2.5 25 20 16 10 6.3 4 2.5 6.8 22 39 56 82 100 150 10 33 47 82 120 150 220 330 22 56 68 100 150 270 330 470 680 33 100 180 330 470 560 680 56 150 330 560 820 1200 1500 80 60 50 45 45 40 40 60 45 45 40 35 35 35 35 50 40 40 35 30 25 25 25 25 30 24 20 17 15 13 13 28 20 16 13 12 12 12 1200 1450 1620 1700 1700 1810 1810 1500 1890 1890 2120 2560 2560 2560 2560 2000 2400 2400 2570 3020 3700 3700 3700 3700 2980 3320 3640 3950 4210 4520 4520 3800 4320 4720 5230 5440 5440 5440 0.10 0.10 0.10 0.12 0.12 0.12 0.12 0.10 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.10 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.15 0.15 0.15 0.15 0.15 0.15 0.12 0.15 0.15 0.15 0.15 0.18 0.18 170 220 312 280 258 200 300 250 330 470 656 600 472 440 660 275 224 272 400 480 540 416 376 544 413 400 576 660 592 448 340 700 600 792 840 775 960 750 size code e7 f8 e12 f13 table9 sep series characteristics list part number t 1 rated voltage (v) rated capacitance ( f) esr 100khz to 300khz (m ? ) (max.) tangent of loss angle (max.) leakage current ( a) (max.) t 2 rated ripple current 100khz (marms) at 105 c 4 . specifications for each series 4 q f d j g j d b u j p o t g p s f b d i t f s j f t t capacitance tolerance : m 20% t 2 after 2 minutes frequency coefficient for ripple current frequency coefficient 120hz ? f ? 1khz 0.05 1khz ? f ? 10khz 0.3 10khz ? f ? 100khz 0.7 100khz ? f ? 500khz 1
|
