? industry standard half-brick ? low-cost design ? 100c baseplate operation ? open-frame packaging ? 24v and 48v input versions ? input pi filter ? optional enable logic ? 1500v isolation features has dc-dc converters provide up to 30 watts of output power in an industry-standard package and footprint. with a maximum case temperature of 100c, the has is well suited for the most demanding telecom, networking, and industrial applications. the has features 1500 vdc isolation, short circuit, and overtemperature protection, as well as six-sided shielding. the has series is available with optional enable and voltage trim pins. please see the had series for dual-output applications. description technical specifications voltage range 24 vdc nominal 18 - 36 vdc 48 vdc nominal 36 - 75 vdc transient 100v/100ms reflected ripple 50 ma input setpoint accuracy 1% line regulation v in min. - v in max., i out rated 0.2% v out load regulation i out min. - i out max., v in nom. 0.2% v out remote sense headroom 0.5 vdc minimum output current 10 % dynamic regulation, loadstep 25% i out pk deviation 4% v out settling time 500 s voltage trim range 10% short circuit / overcurrent protection hiccup current limit threshold range, % of i out rated 110 - 140% ovp trip range 115 - 140% v out nom. remote shutdown reference v in negative shutdown pin current, sourced at off 10 ma max. output general turn-on time 10 ms remote shutdown positive/negative logic switching frequency 250 khz isolation input - output 1500 vdc input - case 1050 vdc output - case 500 vdc temperature coefficient 0.03%/c case temperature operating range -40 to +100c storage range -40 to +125c humidity max., non-condensing 95% vibration, 3 axes, 5 min each 5 g, 10 - 55 hz mtbf ? (bellcore tr-nwt-000332) 2.5 x 10 6 hrs safety ul, cul, tuv weight (approx.) 1.4 oz 50 55 60 65 70 75 80 85 90 95 10 20 30 40 50 60 70 80 90 100 load % efficiency % has030zh-a has030zg-a has030zj-a has030yg-a 60 65 70 75 80 85 90 10 20 30 40 50 60 70 80 90 100 load % efficiency % eff. (18v) eff. (24v) eff. (36v) efficiency vs. load (48v input) efficiency vs. load (24v input) notes ? mtbf predictions may vary slightly from model to model. specifications typically at 25c, normal line, and full load, unless otherwise stated. soldering conditions: i/o pins, 260c, ten seconds; fully compatible with commercial wave-soldering equipment. safety: agency approvals may vary from model to model. please consult factory for specific model information. units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. page 1 of 3 has30 dc-dc series data sheet rev. jun 03, 2004
model input voltage input voltage maximum input output rated output ripple & noise typical (volts) range (volts) current (amps)* voltage (volts) current (amps) pk-pk (mv) efficiency** has030yg-a 24 18-36 2.2 5 6.0 100 83% has030yh-a 24 18-36 2.2 12 2.5 150 87% has030yj-a 24 18-36 2.2 15 2.0 150 86% has030ze-at 48 36-75 1.0 3.3 6.0 100 81% has030zg-a 48 36-75 1.3 5 6.0 100 83% has030zh-a 48 36-75 1.3 12 2.5 150 88% has030zj-a 48 36-75 1.3 15 2.0 150 88% notes: * maximum input current at minimum input voltage, maximum rated output power. ** at nominal v in , rated output. model selection mechanical drawing 1 2 3 4 5 6 7 8 9 0.700"(17.8mm) 1.400"(35.6mm) 1.000"(25.4mm) 0.400"(10.2mm) 0 0.18" 2.28" (57.9mm) dia 0.040" 0.025" ref. 0.50" (12.7mm) (4.6mm) (1.0mm) mounting inserts m3x.5 through 4pl (0.6mm) bottom view 1.700"(43.2mm) -0.50"(-12.7mm) -0.300"(-7.6mm) -0.300"(-7.6mm) 1.400"(35.6mm) 1.000"(25.4mm) 0.400"(10.2mm) 0 0 (-4.8mm) -0.19" (48.3mm) 1.900" (61.0mm) 2.40 " thermal impedance natural convection 7.9 c/w 100 lfm 6.8 c/w 200 lfm 4.9 c/w 300 lfm 3.6 c/w 400 lfm 3.0 c/w tolerances note: thermal impedance data is dependent on many environmental factors. the exact thermal performance should be validated for specific application. 1-v in 2 case 3 on/off 4+v in 5-v out 6 -sense 7 trim 8 +sense 9+v out inches: (millimeters) .xx 0.020 .x 0.5 .xxx 0.010 .xx 0.25 pin: 0.002 0.05 (dimensions as listed unless otherwise specified.) pin function page 2 of 3 has30 dc-dc series data sheet rev. jun 03, 2004 model numbers highlighted in yellow or shaded are not recommended for new designs.
option suffix applicable series remarks negative logic n has, hbd, hbs, hes, hls, hld, les, ttl "low" turns module on qbs, qes, qls, tes, tqd ttl "high" turns module off lucent-compatible trim t has, hbd, hbs, hes, hls, qbs, qes, qls trim 1 ias, les enable 2 iad, ias, les, sms trim and enable 3 ias, les pin length and heatsink options standard pin length is 0.180" (4.6mm) 0.110" (2.8mm) pin length 8 all leaded models 0.150" (3.8mm) pin length 9 all leaded models 0.24" (6.1mm) horizontal heatsink 1h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.24" (6.1mm) vertical heatsink 1v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.45" (11.4mm) horizontal heatsink 2h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.45" (11.4mm) vertical heatsink 2v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.95" (24.1mm) horizontal heatsink 3h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.95" (24.1mm) vertical heatsink 3v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) page 3 of 3 options rev. jun 03, 2004 this page is offered as a reference. consult factory for actual availability of options. when ordering equipment options, use the following suffix information. select preferred option(s) and add the suffix to the model number. ordering option examples are located below the options table. example options: hbs050zg-ant3v = hbs050zg-a with negative logic, lucent-compatible trim, and 0.95? vertical heatsink. les015yj-3n = les015yj with optional trim and enable, negative logic. qbs066zg-at8 = qbs066zg-a with lucent-compatible trim and 0.110? pin length. nuclear and medical applications - power-one products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divi sional president of power-one, inc. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. specifications are subject to change without notice.
|