TLP700 2007-11-20 1 unit in mm weight: 0.26 g (t y p .) 4.580.25 4.0 +0.25 ? 0.20 9.70.3 6.80.25 0.40.1 1.270.2 1.250.25 7.620.25 3.65 +0.15 ? 0.25 0.25 1 2 3 6 5 4 11-5j1 toshiba 11-5j1 ? 0.05 +0.10 toshiba photocoupler gaa ? as ir ed + photo ic TLP700 industrial inverters inverter for air conditioners igbt/power mos fet gate drive TLP700 consists of a gaa ? as light-emitting diode and an integrated photodetector. this unit is 6-lead sdip package. the TLP700 is 50% smaller than the 8-pin dip and meets the reinforced insulation clas s requirements of international safety standards. therefore the mounting area can be reduced in equipment requiring safety standard certification. the TLP700 is suitable for gate driving circuits for igbts or power mosfets. in particular, the TLP700 is capable of ?direct? gate driving of low-power igbts. ? peak output current : 2.0 a (max) ? guaranteed performance over temperature : ? 40~100c ? supply current : 2 ma (max) ? power supply voltage : 15~30 v ? threshold input current : i flh = 5 ma (max) ? switching time (t p lh / t p hl ) : 500 ns (max) ? common mode transient immunity : 10 kv/ s (min) ? isolation voltage : 5000 vrms (min) ? construction mechanical rating 7.62-mm pitch standard type 10.16-mm pitch tlpxxxf type creepage distance clearance insulation thickness 7.0 mm (min) 7.0 mm (min) 0.4 mm (min) 8.0 mm (min) 8.0 mm (min) 0.4 mm (min) ? ul recognized : ul1577, file no. e67349 ? option (d4) type tv approval : en60747-5-2 under plan truth table input led m1 m2 output h on on off h l off off on l 1: anode 2: n.c 3: cathode 4: gnd 5: v o (output) 6: v cc 1 3 4 5 6 2 shield pin configuration (top view) a 0.1- f bypass capacitor must be connected between pins 6 and 4. (see note 6.) schematic v cc gnd i cc (m1) (m2) i o i f 1+ 4 5 6 v o v f 3- shield www.datasheet.co.kr datasheet pdf - http://www..net/
TLP700 2007-11-20 2 absolute maximum ratings (ta = 25 c) characteristics symbol rating unit forward current i f 20 ma forward current derating (ta 85c) i f / ta ? 0.54 ma/c peak transient forward current (note 1) i fp 1 a reverse voltage v r 6 v led junction temperature t j 125 c ?h? peak output current i oph ? 2.0 a ?l? peak output current ta=-40~100 c (note 2) i opl 2.0 a output voltage v o 35 v supply voltage v cc 35 v detector junction temperature t j 125 c operating frequency (note 3) f 50 khz operating temperature range t opr ? 40~100 c storage temperature range t stg ? 55~125 c lead soldering temperature (10 s) (note 4) t sol 260 c isolation voltage (ac, 1 minute, r.h. 60%) (note 5) bv s 5000 vr m s note: using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operat ing temperature/current/voltage, etc. ) are within the absolute maximum ratings. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). note 1: pulse width p w 1 s, 300 pps note 2: exponential waveform pulse width p w 0.3 s, f 15 khz note 3: exponential waveform i oph ? 1.5 a ( 0.3 s), i opl +1.5 a ( 0.3 s), ta=100c note 4: for the effective lead soldering area note 5: device considered a two-terminal device: pins 1, 2 and 3 paired with pins 4, 5 and 6 respectively. note 6: a cerami c capacitor (0.1 f) should be connected from pin 6 to pin 4 to stabilize the operation of the high gain linear amplifier. failure to provide the bypassing may impair the switching property. the total lead length between capacitor and coupler should not exceed 1 cm. recommended operating conditions characteristics symbol min typ. max unit input current, on (note 7) i f (on) 7.5 ? 10 ma input voltage, off v f (off) 0 ? 0.8 v supply voltage * (note 8) v cc 15 ? 30 v peak output current i oph / i opl ? ? 1.5 a operating temperature t opr ? 40 ? 100 c * this item denotes operating ranges, not m eaning of recommended operating conditions. note: recommended operating conditions are given as a design guideline to obtain expected performance of the device. additionally, each item is an independent guid eline respectively. in developing designs using this product, please confirm specified characteristics shown in this document. note 7: input signal rise time (fall time) 0.5 s. note 8: if the vcc rise slope is sharp, an internal circuit might not operate with stability. please design the vcc rise slope under 3.0 v/ s. www.datasheet.co.kr datasheet pdf - http://www..net/
TLP700 2007-11-20 3 electrical characteristics (ta = ? 40 ~ 100 c, unless otherwise specified) characteristics symbol test circuit test condition min typ. * max unit forward voltage v f ? i f = 10 ma, ta = 25 c ? 1.57 1.75 v temperature coefficient of forward voltage ? v f /? ta ? i f = 10 ma ? ? 2.0 ? mv/c input reverse current i r ? v r = 6 v, ta = 25 c ? ? 10 a input capacitance c t ? v =0 v, f = 1 mhz, ta = 25 c ? 100 ? pf i oph1 v 6-5 = -3.5 v ? 1.0 ? 1.4 ? ?h? level i oph2 1 v cc = 15 v i f = 5 ma v 6-5 = -7 v ? 1.5 ? ? i opl1 v 5-4 = 2.5 v 1.0 1.4 ? output current (note 9) ?l? level i opl2 2 v cc = 15 v i f = 0 ma v 5-4 = 7 v 1.5 ? ? a ?h? level v oh 3 vcc1=+15v, vee1=-15v r l = 200 ? , i f = 5 ma 11 13.7 ? output voltage ?l? level v ol 4 vcc1=+15v, vee1=-15v r l = 200 ? ,v f = 0.8 v ? -14.9 -12.5 v ?h? level i cch 5 i f = 10 ma ? 1.3 2.0 supply current ?l? level i ccl 6 v cc = 30 v v o =open i f = 0 ma ? 1.3 2.0 ma threshold input current l h i flh ? v cc = 15 v, v o > 1 v ? 1.8 5 ma threshold input voltage h l v fhl ? v cc = 15 v, v o < 1 v 0.8 ? ? v supply voltage v cc ? ? 15 ? 30 v v uvlo+ ? v o > 2.5v, if = 5 ma 11.0 12.5 13.5 v uvlo thresh hold v uvlo- ? v o < 2.5v, if = 5 ma 9.5 11.0 12.0 v uvlo hysteresis uvlo hys ? ? ? 1.5 ? v (*): all typical values are at ta = 25c note 9: duration of io time 50 s, 1 pulse note 10: this product is more sensitive than conventional pr oducts to electrostatic discharge (esd) owing to its low power consumption design. it is therefore all the more necessary to observe general precautions regarding esd when handling this component. isolation characteristics (ta = 25 c) characteristic symbol test condition min. typ. max. unit capacitance input to output c s vs = 0 v , f = 1mhz (note 5) ? 1.0 ? pf isolation resistance r s r.h. 60 %, v s = 500 v (note 5) 110 12 10 14 ? ? ac, 1 minute 5000 ? ? ac, 1 second, in oil ? 10000 ? vrms isolation voltage bv s dc, 1 minute, in oil ? 10000 ? vdc www.datasheet.co.kr datasheet pdf - http://www..net/
TLP700 2007-11-20 4 switching characteristics (ta = ? 40 ~ 100 c, unless otherwise specified) characteristics symbol test circuit test condition min typ. * max unit l h t p lh i f = 0 5 ma 50 ? 500 propagation delay time h l t p hl i f = 5 0 ma 50 ? 500 output rise time (10 ? 90 %) t r i f = 0 5 ma ? 50 ? output fall time (90 ? 10 %) t f i f = 5 0 ma ? 50 ? switching time dispersion between on and off | t p hl -t p lh | 7 v cc = 30 v r g = 20 c g = 10 nf i f = 0 ? 5 ma ? ? 250 ns common mode transient immunity at high level output cm h i f = 5 ma v o (min) = 26 v ? 10000 ? ? common mode transient immunity at low level output cm l 8 v cm = 1000 vp-p ta = 25 c v cc = 30 v i f = 0 ma v o (max) = 1 v 10000 ? ? v/ s (*) : all typical values are at ta = 25 c. test circuit 1: i oph test circuit 2: i opl test circuit 3: v oh test circuit 4: v ol test circuit 5: i cch test circuit 6: i ccl a i opl v 5-4 v cc 1 3 4 6 0.1 f a i f 1 3 4 6 i oph v 6-5 v cc 0.1 f v cc a i cch i f 1 3 4 6 0.1 f v cc a i ccl 1 3 4 6 0.1 f v cc1 v v oh i f 1 3 4 6 0.1 f v ee1 r l v f 1 3 v cc1 v v ol 4 6 0.1 f v ee1 r l www.datasheet.co.kr datasheet pdf - http://www..net/
TLP700 2007-11-20 5 test circuit 7: t p lh , t p hl , t r , t f , | t p hl -t p lh | test circuit 8: cm h , cm l cm l (cm h ) is the maximum rate of rise (fall) of the comm on mode voltage that can be sustained with the output voltage in the low (high) state. 90 % 10 % 1000 v t f t r 26v cm h 1v cm l v cm v o ? sw a: i f = 5 ma ? sw b: i f = 0 ma cm l = 800 v t r ( s) cm h = ? 800 v t f ( s) v cc 1 3 4 6 0.1 f v o rg = 20 cg = 10nf i f t p hl i f 90 % t f 50% 10 % v o t p lh t r v oh v ol 1 6 i f 3 4 0.1 f v o v cc sw a b + ? v cm www.datasheet.co.kr datasheet pdf - http://www..net/
TLP700 2007-11-20 6 restrictions on product use 20070701-en ? the information contained herein is subject to change without notice. ? toshiba is continually working to improve the quality and reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity an d vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba produc ts, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshib a products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconduct or devices,? or ?toshiba semiconductor reliability handbook? etc. ? the toshiba products listed in this document are in tended for usage in general electronics applications (computer, personal equipment, office equipment, measuri ng equipment, industrial robotics, domestic appliances, etc.).these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfuncti on or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage incl ude atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, et c.. unintended usage of toshiba products listed in his document shall be made at the customer?s own risk. ? the products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. ? gaas(gallium arsenide) is used in this product. the dus t or vapor is harmful to the human body. do not break, cut, crush or dissolve chemically. ? please contact your sales representative for product- by-product details in this document regarding rohs compatibility. please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. www.datasheet.co.kr datasheet pdf - http://www..net/
|
