DIM100WHS17-A000 caution: this device is sensitive to electrostatic discharge. users should follow esd handling procedures. 1/8 www.dynexsemi.com pds5715-1.1 febuary 2004 features 10 s short circuit withstand non punch through silicon isolated copper base plate applications inverters motor controllers the powerline range of high power modules includes half bridge, chopper, dual, single and bi-directional switch configurations covering voltages from 600v to 3300v and currents up to 3600a. the DIM100WHS17-A000 is a half bridge 1700v, n channel enhancement mode, insulated gate bipolar transistor (igbt) module. the igbt has a wide reverse bias safe operating area (rbsoa) plus full 10 s short circuit withstand. the module incorporates an electrically isolated base plate and low inductance construction enabling circuit designers to optimise circuit layouts and utilise grounded heat sinks for safety. ordering information order as: DIM100WHS17-A000 note: when ordering, please use the whole part number. key parameters v ces 1700v v ce(sat) * (typ) 2.7v i c (max) 100a i c(pk) (max) 200a *(measured at the power busbars and not the auxiliary terminals) DIM100WHS17-A000 half bridge igbt module fig. 1 half bridge circuit diagram fig. 2 module outline outline type code: w (see package details for further information) 3(c1) 1(e1c2) 2(e2) 6(g 2 ) 7(e 2 ) 5(e 1 ) 4(g 1 ) .com .com .com 4 .com u datasheet
DIM100WHS17-A000 2/8 caution: this device is sensitive to electrostatic discharge. users should follow esd handling procedures. www.dynexsemi.com test conditions continuous dissipation - junction to case continuous dissipation - junction to case mounting torque 5nm (with mounting grease) transistor diode - mounting - m6 electrical connections - m6 parameter thermal resistance - transistor (per arm) thermal resistance - diode (per arm) thermal resistance - case to heatsink (per module) junction temperature storage temperature range screw torque thermal and mechanical ratings internal insulation: al 2 o 3 clearance: 13mm baseplate material: cu cti (critical tracking index): 175 creepage distance: 24mm symbol r th(j-c) r th(j-c) r th(c-h) t j t stg - units ?c/w ?c/w ?c/w ?c ?c ?c nm nm max. 0.18 0.4 0.015 150 125 125 5 5 typ. - - - - - - - - min. - - - - - ?0 3 2.5 test conditions v ge = 0v - t case = 65?c 1ms, t case = 110?c t case = 25?c, t j = 150?c v r = 0, t p = 10ms, t vj = 125?c commoned terminals to base plate. ac rms, 1 min, 50hz iec1287. v 1 = 1800v, v 2 = 1300v, 50hz rms symbol v ces v ges i c i c(pk) p max i 2 t v isol q pd absolute maximum ratings - per arm stresses above those listed under 'absolute maximum ratings' may cause permanent damage to the device. in extreme conditions, as with all semiconductors, this may include potentially hazardous rupture of the package. appropriate safety prec autions should always be followed. exposure to absolute maximum ratings may affect device reliability. t case = 25?c unless stated otherwise units v v a a w ka 2 s v pc max. 1700 20 100 200 694 1.87 4000 10 parameter collector-emitter voltage gate-emitter voltage continuous collector current peak collector current max. transistor power dissipation diode i 2 t value isolation voltage - per module partial discharge - per module .com .com .com .com 4 .com u datasheet
DIM100WHS17-A000 caution: this device is sensitive to electrostatic discharge. users should follow esd handling procedures. 3/8 www.dynexsemi.com test conditions v ge = 0v, v ce = v ces v ge = 0v, v ce = v ces , t case = 125?c v ge = 20v, v ce = 0v i c = 5ma, v ge = v ce v ge = 15v, i c = 100a v ge = 15v, i c = 100a, , t case = 125?c dc t p = 1ms i f = 100a i f = 100a, t case = 125?c v ce = 25v, v ge = 0v, f = 1mhz - - t j = 125?c, v cc = 1000v, i 1 t p 10 s, v ce(max) = v ces ?l*. di/dt i 2 iec 60747-9 parameter collector cut-off current gate leakage current gate threshold voltage collector-emitter saturation voltage diode forward current diode maximum forward current diode forward voltage input capacitance module inductance - per arm internal transistor resistance - per arm short circuit. i sc electrical characteristics t case = 25?c unless stated otherwise. symbol i ces i ges v ge(th) v ce(sat) ? i f i fm v f ? c ies l m r int sc data units ma ma a v v v a a v v nf nh m ? a a max. 0.5 3 1 6.5 3.4 4.0 100 200 2.5 2.6 - - - - - typ. - - - 5.5 2.7 3.4 - - 2.2 2.3 8 20 0.23 450 400 min. - - - 4.5 - - - - - - - - - - - note: ? measured at the power busbars and not the auxiliary terminals. * l is the circuit inductance + l m .com .com .com .com 4 .com u datasheet
DIM100WHS17-A000 4/8 caution: this device is sensitive to electrostatic discharge. users should follow esd handling procedures. www.dynexsemi.com units ns ns mj ns ns mj c c a mj max. - - - - - - - - - - typ. 590 300 20 320 90 25 1 33 100 21 min. - - - - - - - - - - test conditions i c = 100a v ge = 15v v ce = 900v r g(on) = r g(off) = 10 ? l ~ 100nh i f = 100a, v r = 900v, di f /dt = 1500a/ s parameter turn-off delay time fall time turn-off energy loss turn-on delay time rise time turn-on energy loss gate charge diode reverse recovery charge diode reverse current diode reverse recovery energy electrical characteristics t case = 25?c unless stated otherwise symbol t d(off) t f e off t d(on) t r e on q g q rr i rr e rec t case = 125?c unless stated otherwise units ns ns mj ns ns mj c a mj max. - - - - - - - - - typ. 880 410 30 450 110 40 50 100 32 min. - - - - - - - - - test conditions i c = 100a v ge = 15v v ce = 900v r g(on) = r g(off) = 10 ? l ~ 100nh i f = 100a, v r = 900v, di f /dt = 1250a/ s parameter turn-off delay time fall time turn-off energy loss turn-on delay time rise time turn-on energy loss diode reverse recovery charge diode reverse current diode reverse recovery energy symbol t d(off) t f e off t d(on) t r e on q rr i rr e rec .com .com .com .com 4 .com u datasheet
DIM100WHS17-A000 caution: this device is sensitive to electrostatic discharge. users should follow esd handling procedures. 5/8 www.dynexsemi.com typical characteristics fig. 3 typical output characteristics fig. 4 typical output characteristics fig. 5 typical switching energy vs collector current fig. 6 typical switching energy vs gate resistance 0 5 10 15 20 25 30 35 40 0 102030405060708090100 collector current, i c - (a) switching energy, e sw - (mj) e on e off e rec conditions: t c = 125 ? c, r g = 10 ohms, v cc = 900v 0 10 20 30 40 50 60 70 820 gate resistance, r g - (ohms) switching energy, e sw - (mj) 10 12 14 16 18 conditions: t c = 125 ? c, i c = 100a, v cc = 900v e on e off e rec 0 50 25 75 100 125 150 175 200 0.5 0 1 1.5 2 2.5 3 3.5 4 4.5 5 collector-emitter voltage, v ce - (v) collector current, i c - (a) common emitter. t case = 25?c v ce is measured at power busbars and not the auxiliary terminals v ge = 20v 15v 12v 10v 0 75 50 25 100 125 150 175 200 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 collector-emitter voltage, v ce - (v) collector current, i c - (a) common emitter. t case = 125?c v ce is measured at power busbars and not the auxiliary terminals v ge = 20v 15v 12v 10v .com .com .com .com 4 .com u datasheet
DIM100WHS17-A000 6/8 caution: this device is sensitive to electrostatic discharge. users should follow esd handling procedures. www.dynexsemi.com fig. 7 diode typical forward characteristics fig. 8 reverse bias safe operating area fig. 9 di ode reverse bias safe operating area fig. 10 transient thermal impedance 0 25 50 75 100 125 150 175 200 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 foward volta g e, v f - ( v ) foward current, i f - (a) t j = 125 ? c t j = 25 ? c v f is measured at power busbars and not the auxiliary terminals 0 25 50 75 100 125 150 175 200 225 0 200 400 600 800 1000 1200 1400 1600 1800 collector emitter voltage, v ce - (v) collector current, i c - (a) conditions: t case = 125 ? c v ge = 15v r g(off) = 10 ohms module chip 0 25 50 75 100 125 150 175 200 0 400 800 1200 1600 2000 reverse voltage, v r - (v) reverse recovery current, i rr - (a) t j = 125?c 1 10 100 1000 0.001 0.01 1 0.1 10 pulse width, t p - (s) transient thermal impedance, z th (j-c) - ( c/kw ) diode transistor igbt r i (?c/kw) i (ms) diode r i (?c/kw) i (ms) 1 4.20 0.11 9.98 0.01 2 23.12 3.14 50.56 3.21 3 84.7 45.60 148.48 38.58 4 59.06 143.02 180.18 113.97 .com .com .com .com 4 .com u datasheet
DIM100WHS17-A000 caution: this device is sensitive to electrostatic discharge. users should follow esd handling procedures. 7/8 www.dynexsemi.com package details for further package information, please visit our website or contact customer services. all dimensions in mm, unless stated o therwise. do not scale. fig. 11 package details nominal weight: 420g module outline type code: w 3(c1) 1(e1c2) 2(e2) 6(g 2 ) 7(e 2 ) 5(e 1 ) 4(g 1 ) .com .com .com .com 4 .com u datasheet
www.dynexsemi.com power assembly capability the power assembly group was set up to provide a support service for those customers requiring more than the basic semiconductor, and has developed a flexible range of heatsink and clamping systems in line with advances in device voltages and current capability of our semiconductors. we offer an extensive range of air and liquid cooled assemblies covering the full range of circuit designs in general use today . the assembly group offers high quality engineering support dedicated to designing new units to satisfy the growing needs of our customers. using the latest cad methods our team of design and applications engineers aim to provide the power assembly complete solution (pacs). heatsinks the power assembly group has its own proprietary range of extruded aluminium heatsinks which have been designed to optimise the performance of dynex semiconductors. data with respect to air natural, forced air and liquid cooling (with flow rates) is available on request. for further information on device clamps, heatsinks and assemblies, please contact your nearest sales representative or customer services. customer service tel: +44 (0)1522 502753 / 502901. fax: +44 (0)1522 500020 sales offices benelux, italy & switzerland: tel: +33 (0)1 64 66 42 17. fax: +33 (0)1 64 66 42 19. france: tel: +33 (0)2 47 55 75 5 3 . fax: +33 (0)2 47 55 75 59. germany, northern europe, spain & rest of world: tel: +44 (0)1522 502753 / 502901. fax: +44 (0)1522 500020 north america: tel: (440) 259-2060. fax: (440) 259-2059. tel: (949) 733-3005. fax: (949) 733-2986. these offices are supported by representatives and distributors in many countries world-wide. ?dynex semiconductor 2003 technical documentation ?not for resale. produced in united kingdom headquarters operations dynex semiconductor ltd doddington road, lincoln. lincolnshire. ln6 3lf. united kingdom. tel: +44-(0)1522-500500 fax: +44-(0)1522-500550 this publication is issued to provide information only which (unless agreed by the company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. no warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. the company reserves the right to alter without prior notice the specification, design or price of any product or service. information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. it is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. these products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. all products and materials are sold and services provided subject to the company's conditions of sale, which are available on request. all brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners. http://www.dynexsemi.com e-mail: power_solutions@dynexsemi.com .com .com .com 4 .com u datasheet
|
