|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
1. product profile 1.1 general description passivated high commutation triac in a sot78 (to-220ab) plastic package. intended for use in circuits where high static and dynamic dv/dt and high di/dt can occur. these devices will commutate the full rated rms current at the maxi mum rated junction temperature, without the aid of a snubber. 1.2 features and benefits ? high maximum junction temperature ? high commutation capability 1.3 applications ? motor control ? industrial and domestic heating 1.4 quick reference data 2. pinning information BTA225-600BT three quadrant triacs high commutation rev. 2 ? 9 november 2011 product data sheet to-220ab ? v drm ? 600 v ? i t(rms) ? 25 a ? i tsm ? 200 a ? i gt ? 50 ma (t2+ g+; t2+ g ? ; t2 ? g ? ) table 1. pinning pin description simplified outline symbol 1 main terminal 1 (t1) sot78 (to-220ab) 2 main terminal 2 (t2) 3 gate (g) mb mounting base, connected to main terminal 2 (t2) 123 mb 03ab54 sym051 t1 g t2
BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 2 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation 3. ordering information 4. limiting values [1] although not recommended, off-state voltages up to 800 v may be applied without damage, but the triac may switch to the on-state. the rate of rise of current should not exceed 15 a/ ? s. table 2. ordering information type number package name description version BTA225-600BT sc-46 plastic single-ended package; heatsink mounted; 1 mounting hole; 3-lead to-220ab sot78 table 3. limiting values in accordance with the absolute ma ximum rating system (iec 60134). symbol parameter conditions min max unit v drm repetitive peak off-state voltage [1] -600v i t(rms) rms on-state current f ull sine wave; t mb ? 116 ?c; see figure 4 and 5 -25a i tsm non-repetitive peak on-state current full sine wave; t j =25 ? c prior to surge; see figure 2 and 3 t p =20ms - 200 a t p = 16.7 ms - 220 a i 2 ti 2 t for fusing t = 10 ms - 200 a 2 s di t /dt repetitive rate of rise of on-state current after triggering i tm =30a; i g =0.2a; di g /dt = 0.2 a/ ? s -100a/ ? s i gm peak gate current - 2 a v gm peak gate voltage - 5 v p gm peak gate power - 5 w p g(av) average gate power over any 20 ms period - 0.5 w t stg storage temperature ? 40 +150 ?c t j junction temperature - 150 ?c BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 3 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation ? = conduction angle fig 1. total power dissipation as a function of rms on-state current; maximum values f = 50 hz fig 2. non-repetitive peak on-state current as a function of the number of sinusoidal current cycles; maximum values i t(rms) (a) 0 30 25 15 20 510 001aac222 10 30 20 40 p tot (w) 0 140 120 130 110 t mb(max) (c) 150 = 180 c 120 c 90 c 30 c 60 c 001aac224 50 100 250 200 150 i tsm (a) 0 n 1 10 3 10 2 10 time i tsm i t t p t j initial = 25 c max BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 4 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation t p ? 20 ms fig 3. non-repetitive peak on-state current as a function of pulse width (t p ) for sinusoidal currents; maximum values f = 50 hz; t mb ? 116 ? c fig 4. rms on-state current as a function of surge duration for sinusoidal currents fig 5. rms on-state current as a function of mounting base temperature; maximum values 001aac223 t p (s) 10 ?5 10 ?1 10 ?2 10 ?4 10 ?3 10 2 10 3 i tsm (a) 10 dl t /dt limit time i tsm i t t p t j initial = 25 c max 003aaa805 0 20 40 60 80 10 -2 10 -1 1 10 surge duration (s) i t(rms) (a) 003aaa796 0 10 20 30 ? 50 0 50 100 150 200 (a) 116 c t mb (c) i t(rms) BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 5 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation 5. thermal characteristics table 4. thermal characteristics symbol parameter conditions min typ max unit r th(j-mb) thermal resistance from junction to mounting base full cycle - - 1.0 k/w half cycle - - 1.4 k/w r th(j-a) thermal resistance from junction to ambient in free air - 60 - k/w (1) unidirectional (2) bidirectional fig 6. transient thermal impedance as a function of pulse width 001aac229 10 ?1 10 ?2 1 10 z th(j-mb) (k/w) 10 ?3 t p (s) 10 ?5 11 0 10 ?1 10 ?2 10 ?4 10 ?3 (1) (2) t t p p d BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 6 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation 6. characteristics [1] device does not trigger in the t2 ? , g+ quadrant. table 5. characteristics t j =25 ? c unless otherwise specified. symbol parameter conditions min typ max unit static characteristics i gt gate trigger current v d =12v; i t =0.1a; see figure 8 [1] t2+ g+ 2 18 50 ma t2+ g ? 22150ma t2 ? g ? 23450ma i l latching current v d =12v; i gt =0.1a; see figure 10 t2+ g+ - 31 60 ma t2+ g ? -3 49 0m a t2 ? g ? -3 06 0m a i h holding current v d =12v; i gt =0.1a; see figure 11 -3 16 0m a v t on-state voltage i t =30a; see figure 9 - 1.3 1.55 v v gt gate trigger voltage v d =12v; i t =0.1a; see figure 7 -0 . 71 . 5v v d =400v; i t =0.1a; t j = 150 ? c 0.25 0.4 - v i d off-state leakage current v d =v drm(max) ; t j =150 ? c-15m a dynamic characteristics dv d /dt critical rate of rise of off-state voltage v dm =67% v drm(max) ; t j = 150 ? c; exponential waveform; gate open circuit 1000 4000 - v/ ? s di com /dt critical rate of change of commutating current v dm = 400 v; t j = 150 ?c; i t(rms) = 25 a; without snubber; gate open circuit; see figure 12 920- a/ms t gt gate controlled turn-on time i tm =30a; v d =v drm(max) ; i g = 0.1 a; di g /dt = 5 a/ ? s -2- ? s BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 7 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation (1) t2 ? g ? (2) t2+ g ? (3) t2+ g+ fig 7. normalized gate trigger voltage as a function of junction temperature fig 8. normalized gate trigger current as a function of junction temperature v o = 1.073 v r s = 0.015 ? (1) t j = 150 ? c; typical values (2) t j = 150 ? c; maximum values (3) t j = 25 ? c; maximum values fig 9. on-state current characteristics fig 10. normalized latching current as a function of junction temperature t j ( c) ? 50 0 150 100 50 001aac225 0.8 1.2 1.6 0.4 v gt(tj) v gt(25c) t j (c) ? 50 0 150 100 50 001aac226 1 2 3 0 (1) (2) (3) i gt(tj) i gt(25c) 001aac227 v t (v) 03 2 1 40 20 60 80 i t (a) 0 (3)(2)(1) t j (c) ? 50 0 150 100 50 001aac228 1 2 3 0 i l(tj) i l(25c) BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 8 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation 7. package information refer to mounting instructions for sot78 (to-220ab) package. epoxy meets requirements of ul94 v-0 at 1 8 inch. fig 11. normalized holding current as a function of junction te mperature fig 12. critical rate of change of commutating current as a function of junction temperature; typical values t j (c) ? 50 0 150 100 50 001aac230 1 2 3 0 i h(tj) i h(25c) 001aac231 t j (c) 0 160 120 80 40 10 2 10 10 3 di com /dt (a/ms) 1 BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 9 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation 8. package outline fig 13. package outline sot78 (to-220ab) references outline version european projection issue date iec jedec jeita sot78 sc-46 3-lead to-220ab sot78 08-04-23 08-06-13 notes 1. lead shoulder designs may vary. 2. dimension includes excess dambar. unit a mm 4.7 4.1 1.40 1.25 0.9 0.6 0.7 0.4 16.0 15.2 6.6 5.9 10.3 9.7 15.0 12.8 3.30 2.79 3.8 3.5 a 1 dimensions (mm are the original dimensions) plastic single-ended package; heatsink mounted; 1 mounting hole; 3-lead to-220ab 0 5 10 mm scale b b 1 (2) 1.6 1.0 c d 1.3 1.0 b 2 (2) d 1 e e 2.54 l l 1 (1) l 2 (1) max. 3.0 p q 3.0 2.7 q 2.6 2.2 d d 1 q p l 123 l 1 (1) b 1 (2) (3) b 2 (2) (2) e e b(3) a e a 1 c q l 2 (1) mounting base BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 10 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation 9. revision history table 6. revision history document id release date data sheet status change notice supersedes BTA225-600BT v.2 20111109 product data sheet - BTA225-600BT v.1 modifications: ? the format of this data sheet has been redesigned to comply with the new identity guidelines of nxp semiconductors. ? legal texts have been adapted to the new company name where appropriate. BTA225-600BT v.1 20050303 product data sheet - - BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 11 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation 10. legal information 10.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.nxp.com . 10.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request vi a the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification ? the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer , unless nxp semiconductors and customer have explicitly agreed otherwis e in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 10.3 disclaimers limited warranty and liability ? information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors? aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use ? nxp semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors accepts no liability for inclusion and/or use of nxp semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer?s own risk. applications ? applications that are described herein for any of these products are for illustrative purpos es only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customer?s sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer(s). customer is responsible for doing all necessary testing for the customer?s applic ations and products using nxp semiconductors products in order to av oid a default of the applications and the products or of the application or use by customer?s third party customer(s). nxp does not accept any liability in this respect. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale ? nxp semiconductors products are sold subject to the gener al terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nxp semiconducto rs products by customer. no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any lic ense under any copyrights, patents or other industrial or intellectual property rights. export control ? this document as well as the item(s) described herein may be subject to export control regulations. export might require a prior authorization from competent authorities. document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification. BTA225-600BT all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 9 november 2011 12 of 13 nxp semiconductors BTA225-600BT three quadrant triacs high commutation quick reference data ? the quick reference data is an extract of the product data given in the limiting values and characteristics sections of this document, and as such is not comple te, exhaustive or legally binding. non-automotive qualified products ? unless this data sheet expressly states that this specific nxp semicon ductors product is automotive qualified, the product is not suitable for automotive use. it is neither qualified nor tested in accordance with automotive testing or application requirements. nxp semiconductors accepts no liabili ty for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. in the event that customer uses t he product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without nxp semiconductors? warranty of the product for such automotive applicat ions, use and specifications, and (b) whenever customer uses the product for automotive applications beyond nxp semiconductors? specifications such use shall be solely at customer?s own risk, and (c) customer fully indemnifies nxp semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive app lications beyond nxp semiconductors? standard warranty and nxp semiconduct ors? product specifications. 10.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. 11. contact information for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com nxp semiconductors BTA225-600BT three quadrant triacs high commutation ? nxp b.v. 2011. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please se nd an email to: salesaddresses@nxp.com date of release: 9 november 2011 document identifier: BTA225-600BT please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 12. contents 1 product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 general description . . . . . . . . . . . . . . . . . . . . . 1 1.2 features and benefits . . . . . . . . . . . . . . . . . . . . 1 1.3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.4 quick reference data . . . . . . . . . . . . . . . . . . . . 1 2 pinning information . . . . . . . . . . . . . . . . . . . . . . 1 3 ordering information . . . . . . . . . . . . . . . . . . . . . 2 4 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 thermal characteristics . . . . . . . . . . . . . . . . . . 5 6 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 6 7 package information . . . . . . . . . . . . . . . . . . . . . 8 8 package outline . . . . . . . . . . . . . . . . . . . . . . . . . 9 9 revision history . . . . . . . . . . . . . . . . . . . . . . . . 10 10 legal information. . . . . . . . . . . . . . . . . . . . . . . 11 10.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 11 10.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 10.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 10.4 trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 12 11 contact information. . . . . . . . . . . . . . . . . . . . . 12 12 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 |
Price & Availability of BTA225-600BT |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |